| Age | Commit message (Collapse) | Author |
|---|
|
AMxxxx dpll_data previously had autoidle_mask set, even if these SoC:s
don't have autoidle register. Remove the bit-field value as it is unused,
also drop the unnecessary DPLL_HAS_AUTOIDLE flag passing during init,
as we can just simply check against the contents of the autoidle_mask.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This rewrites the SIRF pinctrl driver to allocate a state container
for the GPIO chip, just as is done for the pin controller, and
use the gpiochip_add_pin_range() to add the range from the gpiochip
side rather than adding the range from the pinctrl side.
All resulting changes are done in order to pass around a state
container rather than refer to a static global object.
Acked-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Remove the 96-byte irb array from the lowcore and create a per-cpu
variable instead. That way we will pick up any change in the definition
of the struct irb automatically.
Acked-By: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Add "power-source" property to generic options used for DT parsing files.
This enables drivers, which use generic pin configurations, to get the
value passed to this property.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Fixes the following warning:
WARNING: drivers/built-in.o(.text.unlikely+0x2c50): Section mismatch in reference from the function exynos4_clk_sleep_init() to the (unknown reference) .init.data:(unknown)
The function exynos4_clk_sleep_init() references
the (unknown reference) __initdata (unknown).
This is often because exynos4_clk_sleep_init lacks a __initdata
annotation or the annotation of (unknown) is wrong.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
It's quite possible that multiple pcf857x can be hooked up
to the same interrupt line with the processor. So add IRQF_SHARED
in request irq..
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Currently irq_domain_cleanup is called twice if irq_domain_init fails.
This causes the following crash.
Unable to handle kernel paging request at virtual address 00100104
pgd = c0004000
[00100104] *pgd=00000000
Internal error: Oops: 805 [#1] SMP ARM
Modules linked in:
CPU: 0 PID: 6 Comm: kworker/u4:0 Not tainted 3.12.15-01889-gedd10a8-dirty #4
Workqueue: deferwq deferred_probe_work_func
task: ed0ee800 ti: ed116000 task.ti: ed116000
PC is at irq_domain_remove+0x3c/0x8c
LR is at 0x0
pc : [<c0089734>] lr : [<00000000>] psr: a0000013
sp : ed117b50 ip : 00100100 fp : ed117b64
r10: ed5d1a04 r9 : 00000008 r8 : 00000000
r7 : ffffffea r6 : ed5d1a20 r5 : ed5d1a00 r4 : ed5e7540
r3 : 00200200 r2 : 00100100 r1 : c08aa180 r0 : 00200200
Flags: NzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel
Control: 10c53c7d Table: 8000406a DAC: 00000017
Process kworker/u4:0 (pid: 6, stack limit = 0xed116248)
Stack: (0xed117b50 to 0xed118000)
7b40: 0000016b ed5d5f10 ed117b74 ed117b68
7b60: c02c8910 c0089704 ed117bb4 ed117b78 c02c8e14 c02c8900 ed5d1a04 ed5d4e80
...
<snip>
...
fe0: 00000000 00000000 00000000 00000000 00000013 00000000 384a13ea 1590210a
Backtrace:
[<c00896f8>] (irq_domain_remove+0x0/0x8c) from [<c02c8910>] (pcf857x_irq_domain_cleanup+0x1c/0x20)
r4:ed5d5f10 r3:0000016b
[<c02c88f4>] (pcf857x_irq_domain_cleanup+0x0/0x20) from [<c02c8e14>] (pcf857x_probe+0x2a8/0x364)
[<c02c8b6c>] (pcf857x_probe+0x0/0x364) from [<c04787ac>] (i2c_device_probe+0x80/0xc0)
[<c047872c>] (i2c_device_probe+0x0/0xc0) from [<c036c33c>] (driver_probe_device+0x104/0x240)
r6:00000000 r5:ed5d1a20 r4:c08c709c r3:c047872c
[<c036c238>] (driver_probe_device+0x0/0x240) from [<c036c558>] (__device_attach+0x48/0x4c)
r7:ed4fc480 r6:c036c510 r5:ed5d1a20 r4:c0866bb8
[<c036c510>] (__device_attach+0x0/0x4c) from [<c036a6d8>] (bus_for_each_drv+0x4c/0x94)
r5:ed5d1a20 r4:00000000
[<c036a68c>] (bus_for_each_drv+0x0/0x94) from [<c036c1f4>] (device_attach+0x78/0x90)
r6:c087fe50 r5:ed5d1a54 r4:ed5d1a20
[<c036c17c>] (device_attach+0x0/0x90) from [<c036b76c>] (bus_probe_device+0x8c/0xb4)
r6:c087fe50 r5:ed5d1a20 r4:ed5d1a20 r3:ed17e1c0
[<c036b6e0>] (bus_probe_device+0x0/0xb4) from [<c0369888>] (device_add+0x34c/0x624)
r6:ed5d1a28 r5:00000000 r4:ed5d1a20 r3:fffffffe
[<c036953c>] (device_add+0x0/0x624) from [<c0369b7c>] (device_register+0x1c/0x20)
...
<snip>
...
[<c0060844>] (process_one_work+0x0/0x37c) from [<c0061040>] (worker_thread+0x13c/0x3c4)
[<c0060f04>] (worker_thread+0x0/0x3c4) from [<c00670ec>] (kthread+0xac/0xb8)
[<c0067040>] (kthread+0x0/0xb8) from [<c00148b8>] (ret_from_fork+0x14/0x3c)
r7:00000000 r6:00000000 r5:c0067040 r4:ed105d20
Code: e59fc04c e591e000 e59f0048 e154000e (e5823004)
---[ end trace 59dd1e90032c4217 ]---
Signed-off-by: George Cherian <george.cherian@ti.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Commit 3e3bed913e8bbd78f38cefd5d575475f45c05dd0
"gpio: mcp23s08: fixed count variable for devicetree probing"
introduced a loop check to see if the number of chips were
unconsistent and going below zero counting downwards, but
this requires the counting variable to be able to be
negative, so switch the variable from unsigned to int.
Cc: Michael Stickel <ms@mycable.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
|
|
Some oscillators can be turned off during off-idle saving few
a little bit power at the cost of the oscillator start up
latency.
If you board can do this, you can now enable it by using the
ti,twl4030-power-idle-osc-off compatible flag.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
With the recommended twl4030 configuration added, we can now add
board specific changes as modifications to the recommended
configuration.
Note that the data is private to this driver, and the data must
always have a NULL resource in the sentinel.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
These settings are based on the "Recommended Sleep Sequences for
the Zoom Platform".
The settings assume most of the regulators are under control of
Linux, and twl4030 only cuts off VDD1 and VDD2 during off-idle as
Linux cannot do it.
For any board specific changes to these, let's patch them in as
changes to the generic data in the follow-up patches. This keeps
the board specific changes small.
Note that this does not consider the twl5030 errata 27 and 28.
That can be added later on after it has been tested. For more
information about errata 27 and 28.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The twl4030 PMIC needs to be configured properly for things like
warm reset and deeper idle states so the PMIC manages the regulators
properly based on the hardware triggers from the SoC. Earlier
we have configured twl4030 using platform data, but we want to
do it for device tree based booting also.
In some cases configuring twl4030 is needed for things to work.
For example, when rebooting an OMAP3530 at 125 MHz, it hangs.
With this patch, TWL4030 will be reset when a warm reset occures,
and OMAP3530 does not hang on reboot.
Let's add device tree support and configure things for warm reset
as the default when compatible = "ti,twl4030-power". More
complicated configurations can be added to the driver based on
other compatible flags.
Note we now also make the pdata const like it should be.
This allows use it for match->data with the device tree
related functions.
Based on earlier patch by Matthias Brugger <matthias.bgg@gmail.com>
and Lesly A M <leslyam@ti.com>.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The two loops in r852_write_buf() are designed to handle 4-byte-aligned
and then 1-byte-aligned portions, respectively. However, there are two
issues:
(1) The first loop will only terminate if 'len' is a multiple of 4
(2) The second loop will never terminate if it runs at least once
Rewrite these loops as they were probably intended. Compile tested only.
Issues pointed out by Coverity Scan.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
|
|
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
Set, but unused, variable.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
On m86k, and maybe a few other architectures, we get this kind of
warning, due to misuse of volatile:
drivers/mtd/maps/sc520cdp.c: In function 'sc520cdp_setup_par':
>> drivers/mtd/maps/sc520cdp.c:223:2: warning: passing argument 1 of 'iounmap' discards 'volatile' qualifier from pointer target type [enabled by default]
arch/m68k/include/asm/raw_io.h:22:13: note: expected 'void *' but argument is of type 'volatile long unsigned int *'
Rather than annotating the variable declaration, let's just use the
proper accessors, which add the 'volatile' qualifier to the operation.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
drivers/mtd/devices/slram.c: In function 'init_slram':
drivers/mtd/devices/slram.c:283:6: warning: variable 'i' set but not used [-Wunused-but-set-variable]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
We have these bits partially defined in two different
places, so let's fix them up and add defines for the
missing bits. These bits are the same for P1_SW_EVENTS,
P2_SW_EVENTS and P3_SW_EVENTS.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Looks like we can still hit the issue of wrong load order of
twl4030 configuration. If we have a sleep configuration loaded,
and do a warm reset, the device can hang while initializing the
wakeup12 sequence. We do have a warning message about wrong order
of twl4030 configuration, but in this case it does not help as
the sleep configuration was loaded during the previous boot and
the state of twl4030 is maintained throughout the warm reset.
Fix the issue by clearing any existing sleep configuration
before we load the warm reset configuration.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Move the panel/encoder driver compatible-string converter from
arch/arm/mach-omap2/display.c to omapdss driver. That is a more logical
place for it, as it's really an omapdss internal hack.
The code is rewritten to follow the video node graph, starting from
omapdss. This removes the need to have the device compatible-string
database.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
git://nv-tegra.nvidia.com/user/pdeschrijver/linux into clk-fixes
PLLE fixes for 3.15
|
|
If mddev->ro is set, md_to_sync will (correctly) abort.
However in that case MD_RECOVERY_INTR isn't set.
If a RESHAPE had been requested, then ->finish_reshape() will be
called and it will think the reshape was successful even though
nothing happened.
Normally a resync will not be requested if ->ro is set, but if an
array is stopped while a reshape is on-going, then when the array is
started, the reshape will be restarted. If the array is also set
read-only at this point, the reshape will instantly appear to success,
resulting in data corruption.
Consequently, this patch is suitable for any -stable kernel.
Cc: stable@vger.kernel.org (any)
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
There is otherwise a risk of a null pointer dereference.
Found by cppcheck, a static code analysis program.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Add MSI support to the R-Car PCIe driver.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
|
|
This PCIe Host driver currently does not support MSI, so cards fall back to
INTx interrupts.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Commit c686078 ("clk: divider: Add round to closest divider") introduced
a helper function to check whether given divisor is the best one instead
of direct check. However due to int type used instead of unsigned long
for passing calculated rates to this function in certain cases an
overflow could occur, for example when trying to obtain maximum possible
clock rate by calling clk_round_rate(..., UINT_MAX).
This patch fixes this issue by changing the type of rate, now and best
arguments of the function to unsigned long, which is the type that
should be used for clock rates.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
Failure to terminate this match table can lead to boot failures
depending on where the compiler places the match table.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
This is a static checker fix. The "dev" variable is always NULL after
the while statement so we would be dereferencing a NULL pointer here.
Fixes: 819a3eba4233 ('[PATCH] applicom: fix error handling')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Function genwqe_free_sync_sgl() returns the value of variable 'rc'. 'rc' is
only set in the error paths, thus initialize it by 0. Coverity CID 1204242.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add support for shared PCI IRQs to mcb and mcb-pci.
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@men.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Setting a 'silent' parameter without a synth would crash the kernel.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Added spaces needed in the proper places to address:
ERROR: space required after that ',' (ctx:VxV)
ERROR: space required after that ';' (ctx:VxV)
ERROR: space required after that close brace '}'
ERROR: space required before the open brace '{'
ERROR: space required before the open parenthesis '('
ERROR: spaces required around that '<' (ctx:VxV)
ERROR: spaces required around that '=' (ctx:VxV)
ERROR: spaces required around that '==' (ctx:VxV)
Signed-off-by: Chaitanya Hazarey <c@24.io>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Implement the clk->determine_rate method for Broadcom Kona peripheral
clocks. This allows a peripheral clock to be re-parented in order to
satisfy a rate change request. This takes the place of the previous
kona_peri_clk_round_rate() functionality, though that function remains
because it is used by the new one.
The parent clock that allows the peripheral clock to produce a rate
closest to the one requested is the one selected, though the current
parent is used by default.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
Unconditionally wake up the child device when the power session is
recovered.
This addresses the following scenarios:
1/ The device may need a reset on power-session loss, without this
change port power-on recovery exposes khubd to scenarios that
usb_port_resume() is set to handle. Prior to port power control the
only time a power session would be lost is during dpm_suspend of the
hub. In that scenario usb_port_resume() is guaranteed to be called
prior to khubd running for that port. With this change we wakeup the
child device as soon as possible (prior to khubd running again for this
port).
Although khubd has facilities to wake a child device it will only do
so if the portstatus / portchange indicates a suspend state. In the
case of port power control we are not coming from a hub-port-suspend
state. This implementation simply uses pm_request_resume() to wake the
device and relies on the port_dev->status_lock to prevent any collisions
between khubd and usb_port_resume().
2/ This mechanism rate limits port power toggling. The minimum port
power on/off period is now gated by the child device suspend/resume
latency. Empirically this mitigates devices downgrading their connection
on perceived instability of the host connection. This ratelimiting is
really only relevant to port power control testing, but it is a nice
side effect of closing the above race. Namely, the race of khubd for
the given port running while a usb_port_resume() event is pending.
3/ Going forward we are finding that power-session recovery requires
warm-resets (http://marc.info/?t=138659232900003&r=1&w=2). This
mechanism allows for warm-resets to be requested at the same point in
the resume path for hub dpm_suspend power session losses, or port
rpm_suspend power session losses.
4/ If the device *was* disconnected the only time we'll know for sure is
after a failed resume, so it's necessary for usb_port_runtime_resume()
to expedite a usb_port_resume() to clean up the removed device. The
reasoning for this is "least surprise" for the user. Turning on a port
means that hotplug detection is again enabled for the port, it is
surprising that devices that were removed while the port was off are not
disconnected until they are attempted to be used. As a user "why would
I try to use a device I removed from the system?"
1, 2, and 4 are not a problem in the system dpm_resume() case because,
although the power-session is lost, khubd is frozen until after device
resume. For the rpm_resume() case pm_request_resume() is used to
request re-validation of the device, and if it happens to collide with a
khubd run we rely on the port_dev->status_lock to synchronize those
operations.
Besides testing, the primary scenario where this mechanism is expected
to be triggered is when the user changes the port power policy
(control/pm_qos_no_poweroff, or power/control). Each time power is
enabled want to revalidate the child device, where the revalidation is
handled by usb_port_resume().
Given that this arranges for port_dev->child to be de-referenced in
usb_port_runtime_resume() we need to make sure not to collide with
usb_disconnect() that frees the usb_device. To this end we hold the
port active with the "child_usage" reference across the disconnect
event. Subsequently, the need to access hub->child_usage_bits lead to
the creation of hub_disconnect_children() to remove any ambiguity of
which "hub" is being acted on in usb_disconnect() (prompted-by sharp
eyes from Alan).
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Per Alan:
"You mean from within hub_handle_remote_wakeup()? That routine will
never get called if CONFIG_PM_RUNTIME isn't enabled, because khubd
never sees wakeup requests if they arise during system suspend.
In fact, that routine ought to go inside the "#ifdef CONFIG_PM_RUNTIME"
portion of hub.c, along with the other suspend/resume code."
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In general we do not want khubd to act on port status changes that are
the result of in progress resets or USB runtime PM operations.
Specifically port power control testing has been able to trigger an
unintended disconnect in hub_port_connect_change(), paraphrasing:
if ((portstatus & USB_PORT_STAT_CONNECTION) && udev &&
udev->state != USB_STATE_NOTATTACHED) {
if (portstatus & USB_PORT_STAT_ENABLE) {
/* Nothing to do */
} else if (udev->state == USB_STATE_SUSPENDED &&
udev->persist_enabled) {
...
} else {
/* Don't resuscitate */;
}
}
...by falling to the "Don't resuscitate" path or missing
USB_PORT_STAT_CONNECTION because usb_port_resume() was in the middle of
modifying the port status.
So, we want a new lock to hold off khubd for a given port while the
child device is being suspended, resumed, or reset. The lock ordering
rules are now usb_lock_device() => usb_lock_port(). This is mandated by
the device core which may hold the device_lock on the usb_device before
invoking usb_port_{suspend|resume} which in turn take the status_lock on
the usb_port. We attempt to hold the status_lock for the duration of a
port_event() run, and drop/re-acquire it when needing to take the
device_lock. The lock is also dropped/re-acquired during
hub_port_reconnect().
This patch also deletes hub->busy_bits as all use cases are now covered
by port PM runtime synchronization or the port->status_lock and it
pushes down usb_device_lock() into usb_remote_wakeup().
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If a port is powered-off, or in the process of being powered-off, prevent
khubd from operating on it. Otherwise, the following sequence of events
leading to an unintended disconnect may occur:
Events:
(0) <set pm_qos_no_poweroff to '0' for port1>
(1) hub 2-2:1.0: hub_resume
(2) hub 2-2:1.0: port 1: status 0301 change 0000
(3) hub 2-2:1.0: state 7 ports 4 chg 0002 evt 0000
(4) hub 2-2:1.0: port 1, power off status 0000, change 0000, 12 Mb/s
(5) usb 2-2.1: USB disconnect, device number 5
Description:
(1) hub is resumed before sending a ClearPortFeature request
(2) hub_activate() notices the port is connected and sets
hub->change_bits for the port
(3) hub_events() starts, but at the same time the port suspends
(4) hub_connect_change() sees the disabled port and triggers disconnect
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In preparation for synchronizing port handling with pm_runtime
transitions refactor port handling into its own subroutine.
We expect that clearing some status flags will be required regardless of
the port state, so handle those first and group all non-trivial actions
at the bottom of the routine.
This also splits off the bottom half of hub_port_connect_change() into
hub_port_reconnect() in prepartion for introducing a port->status_lock.
hub_port_reconnect() will expect the port lock to not be held while
hub_port_connect_change() expects to enter with it held.
Other cleanups include:
1/ reflowing to 80 columns
2/ replacing redundant usages of 'hub->hdev' with 'hdev'
3/ consolidate clearing of ->change_bits() in hub_port_connect_change
4/ consolidate calls to usb_reset_device
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The port pm_runtime implementation unconditionally clears FEAT_C_ENABLE
after clearing PORT_POWER, but the bit is reserved on usb3 hub ports.
We expect khubd to be prevented from running because the port state is
not RPM_ACTIVE, so we need to clear any errors for usb2 ports.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Three reasons:
1/ It's an invalid operation on usb3 ports
2/ There's no guarantee of when / if a usb2 port has entered an error
state relative to PORT_POWER request
3/ The port is active / powered at this point, so khubd will clear it as
a matter of course
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
ClearPortFeature(PORT_POWER) on a usb3 port places the port in either a
DSPORT.Powered-off-detect / DSPORT.Powered-off-reset loop, or the
DSPORT.Powered-off state. There is no way to ensure that RX
terminations will persist in this state, so it is possible a device will
degrade to its usb2 connection. Prevent this by blocking power-off of a
usb3 port while its usb2 peer is active, and powering on a usb3 port
before its usb2 peer.
By default the latency between peer power-on events is 0. In order for
the device to not see usb2 active while usb3 is still powering up inject
the hub recommended power_on_good delay. In support of satisfying the
power_on_good delay outside of hub_power_on() refactor the places where
the delay is consumed to call a new hub_power_on_good_delay() helper.
Finally, because this introduces several new checks for whether a port
is_superspeed, cache that disctinction at port creation so that we don't
need to keep looking up the parent hub device.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
[alan]: add a 'superspeed' flag to the port
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We want to manipulate ->did_runtime_put in usb_port_runtime_resume(),
but we don't want that to collide with other updates. Move usb_port
flags to new port-bitmap fields in usb_hub. "did_runtime_put" is renamed
"child_usage_bits" to reflect that it is strictly standing in for the
fact that usb_devices are not the device_model children of their parent
port.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The usb topology after this change will have symlinks between usb3 ports
and their usb2 peers, for example:
usb2/2-1/2-1:1.0/2-1-port1/peer => ../../../../usb3/3-1/3-1:1.0/3-1-port1
usb2/2-1/2-1:1.0/2-1-port2/peer => ../../../../usb3/3-1/3-1:1.0/3-1-port2
usb2/2-1/2-1:1.0/2-1-port3/peer => ../../../../usb3/3-1/3-1:1.0/3-1-port3
usb2/2-1/2-1:1.0/2-1-port4/peer => ../../../../usb3/3-1/3-1:1.0/3-1-port4
usb2/2-0:1.0/usb2-port1/peer => ../../../usb3/3-0:1.0/usb3-port1
usb2/2-0:1.0/usb2-port2/peer => ../../../usb3/3-0:1.0/usb3-port2
usb2/2-0:1.0/usb2-port3/peer => ../../../usb3/3-0:1.0/usb3-port3
usb2/2-0:1.0/usb2-port4/peer => ../../../usb3/3-0:1.0/usb3-port4
usb3/3-1/3-1:1.0/usb3-1-port1/peer => ../../../../usb2/2-1/2-1:1.0/2-1-port1
usb3/3-1/3-1:1.0/usb3-1-port2/peer => ../../../../usb2/2-1/2-1:1.0/2-1-port2
usb3/3-1/3-1:1.0/usb3-1-port3/peer => ../../../../usb2/2-1/2-1:1.0/2-1-port3
usb3/3-1/3-1:1.0/usb3-1-port4/peer => ../../../../usb2/2-1/2-1:1.0/2-1-port4
usb3/3-0:1.0/usb3-port1/peer => ../../../usb2/2-0:1.0/usb2-port1
usb3/3-0:1.0/usb3-port2/peer => ../../../usb2/2-0:1.0/usb2-port2
usb3/3-0:1.0/usb3-port3/peer => ../../../usb2/2-0:1.0/usb2-port3
usb3/3-0:1.0/usb3-port4/peer => ../../../usb2/2-0:1.0/usb2-port4
Introduce link_peers_report() to notify on all link_peers() failure
cases.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
ACPI identifies peer ports by setting their 'group_token' and
'group_position' _PLD data to the same value. If a platform has tier
mismatch [1] , ACPI can override the default (USB3 defined) peer port
association for internal hubs. External hubs follow the default peer
association scheme.
Location data is cached as an opaque cookie in usb_port_location data.
Note that we only consider the group_token and group_position attributes
from the _PLD data as ACPI specifies that group_token is a unique
identifier.
When we find port location data for a port then we assume that the
firmware will also describe its peer port. This allows the
implementation to only ever set the peer once. This leads to a question
about what happens when a pm runtime event occurs while the peer
associations are still resolving. Since we only ever set the peer
information once, a USB3 port needs to be prevented from suspending
while its ->peer pointer is NULL (implemented in a subsequent patch).
There is always the possibility that firmware mis-identifies the ports,
but there is not much the kernel can do in that case.
[1]: xhci 1.1 appendix D figure 131
[2]: acpi 5 section 6.1.8
[alan]: don't do default peering when acpi data present
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Given that root hub port peers are already established, external hub peer
ports can be determined by traversing the device topology:
1/ ascend to the parent hub and find the upstream port_dev
2/ walk ->peer to find the peer port
3/ descend to the peer hub via ->child
4/ find the port with the matching port id
Note that this assumes the port labeling scheme required by the
specification [1].
[1]: usb3 3.1 section 10.3.3
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Assume that the peer of a superspeed port is the port with the same id
on the shared_hcd root hub. This identification scheme is required of
external hubs by the USB3 spec [1]. However, for root hubs, tier mismatch
may be in effect [2]. Tier mismatch can only be enumerated via platform
firmware. For now, simply perform the nominal association.
A new lock 'usb_port_peer_mutex' is introduced to synchronize port
device add/remove with peer lookups. It protects peering against
changes to hcd->shared_hcd, hcd->self.root_hub, hdev->maxchild, and
port_dev->child pointers.
[1]: usb 3.1 section 10.3.3
[2]: xhci 1.1 appendix D
Cc: Alan Stern <stern@rowland.harvard.edu>
[alan: usb_port_peer_mutex locking scheme]
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Once usb-acpi has set the port's connect type the usb_device's
->removable attribute can be set in the standard location
set_usb_port_removable().
This also changes behavior in the case where the firmware says that the
port connect type is unknown. In that case just use the default setting
determined from the hub descriptor.
Note, we no longer pass udev->portnum to acpi_find_child_device() in the
root hub case since:
1/ the usb-core sets this to zero
2/ acpi always expects zero
...just pass zero.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The current port name "portX" is ambiguous. Before adding more port
messages rename ports to "<hub-device-name>-portX"
This is an ABI change, but the suspicion is that it will go unnoticed as
the port power control implementation has been broken since its
introduction. If however, someone was relying on the old name we can
add sysfs links from the old name to the new name.
Additionally, it unifies/simplifies port dev_printk messages and modifies
instances of:
dev_XXX(hub->intfdev, ..."port %d"...
dev_XXX(&hdev->dev, ..."port%d"...
into:
dev_XXX(&port_dev->dev, ...
Now that the names are unique usb_port devices it would be nice if they
could be included in /sys/bus/usb. However, it turns out that this
breaks 'lsusb -t'. For now, create a dummy port driver so that print
messages are prefixed "usb 1-1-port3" rather than the
subsystem-ambiguous " 1-1-port3".
Finally, it corrects an odd usage of sscanf("port%d") in usb-acpi.c.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
