| Age | Commit message (Collapse) | Author |
|---|
|
commit 8558e4a26b00225efeb085725bc319f91201b239 upstream.
This is my example conversion of a few existing mmap users. The mtdchar
case is actually disabled right now (and stays disabled), but I did it
because it showed up on my "git grep", and I was familiar with the code
due to fixing an overflow problem in the code in commit 9c603e53d380
("mtdchar: fix offset overflow detection").
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2323036dfec8ce3ce6e1c86a49a31b039f3300d1 upstream.
This is my example conversion of a few existing mmap users. The HPET
case is simple, widely available, and easy to test (Clemens Ladisch sent
a trivial test-program for it).
Test-program-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fc9bbca8f650e5f738af8806317c0a041a48ae4a upstream.
This is my example conversion of a few existing mmap users. The
fb_mmap() case is a good example because it is a bit more complicated
than some: fb_mmap() mmaps one of two different memory areas depending
on the page offset of the mmap (but happily there is never any mixing of
the two, so the helper function still works).
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 46fc4c909339f5a84d1679045297d9d2fb596987 upstream.
And make use of it in b43. This fixes a regression introduced with
49d55cef5b1925a5c1efb6aaddaa40fc7c693335
b43: N-PHY: implement spurious tone avoidance
This commit made BCM4322 use only MCS 0 on channel 13, which of course
resulted in performance drop (down to 0.7Mb/s).
Reported-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f09a878511997c25a76bf111a32f6b8345a701a5 upstream.
The hardware parsing of Control Wrapper Frames needs to be disabled, as
it has been causing spurious decryption error reports. The initvals for
other chips have been updated to disable it, but AR9580 was left out for
some reason.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 319e7bd96aca64a478f3aad40711c928405b8b77 upstream.
Since the firmware has been open sourced, the minor version has been
bumped to 1.4 and the API/ABI will stay compatible across further 1.x
releases.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d3f677afb8076d09d090ff0a5d1229c9dd9f136e upstream.
The patch also adds a couple of fixes
- For the 57766 and non Ax versions of 57765, bootcode needs to setup
the PCIE Fast Training Sequence (FTS) value to prevent transmit hangs.
Unfortunately, it does not have enough room in the selfboot case (i.e.
devices with no NVRAM). The driver needs to implement this.
- For performance reasons, the 2k DMA engine mode on the 57766 should
be enabled and dma size limited to 2k for standard sized packets.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Joseph Salisbury <joseph.salisbury@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c8dc9c654794a765ca61baed07f84ed8aaa7ca8c upstream.
Set mddev queue's max_write_same_sectors to its chunk_sector value (before
disk_stack_limits merges the underlying disk limits.) With that in place,
be sure to handle writes coming down from the block layer that have the
REQ_WRITE_SAME flag set. That flag needs to be copied into any newly cloned
write bio.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: "Martin K. Petersen" <martin.petersen@oracle.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0443de5fbf224abf41f688d8487b0c307dc5a4b4 upstream.
To get correct endianes on little endian cpus (like arm) while reading device
tree properties, this patch replaces of_get_property() with
of_property_read_u32(). While there use of_property_read_bool() for the
handling of the boolean "nxp,no-comparator-bypass" property.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit db388d6460ffa53b3b38429da6f70a913f89b048 upstream.
Since commit:
1c6c695 genirq: Reject bogus threaded irq requests
threaded irqs must provide a primary handler or set the IRQF_ONESHOT flag.
Since the mcp251x driver doesn't make use of a primary handler set the
IRQF_ONESHOT flag.
Reported-by: Mylene Josserand <Mylene.Josserand@navocap.com>
Tested-by: Mylene Josserand <Mylene.Josserand@navocap.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 852e4a8152b427c3f318bb0e1b5e938d64dcdc32 upstream.
Since commit 89c8d91e31f2 ("tty: localise the lock") I see a dead lock
in one of my dummy_hcd + g_nokia test cases. The first run was usually
okay, the second often resulted in a splat by lockdep and the third was
usually a dead lock.
Lockdep complained about tty->hangup_work and tty->legacy_mutex taken
both ways:
| ======================================================
| [ INFO: possible circular locking dependency detected ]
| 3.7.0-rc6+ #204 Not tainted
| -------------------------------------------------------
| kworker/2:1/35 is trying to acquire lock:
| (&tty->legacy_mutex){+.+.+.}, at: [<c14051e6>] tty_lock_nested+0x36/0x80
|
| but task is already holding lock:
| ((&tty->hangup_work)){+.+...}, at: [<c104f6e4>] process_one_work+0x124/0x5e0
|
| which lock already depends on the new lock.
|
| the existing dependency chain (in reverse order) is:
|
| -> #2 ((&tty->hangup_work)){+.+...}:
| [<c107fe74>] lock_acquire+0x84/0x190
| [<c104d82d>] flush_work+0x3d/0x240
| [<c12e6986>] tty_ldisc_flush_works+0x16/0x30
| [<c12e7861>] tty_ldisc_release+0x21/0x70
| [<c12e0dfc>] tty_release+0x35c/0x470
| [<c1105e28>] __fput+0xd8/0x270
| [<c1105fcd>] ____fput+0xd/0x10
| [<c1051dd9>] task_work_run+0xb9/0xf0
| [<c1002a51>] do_notify_resume+0x51/0x80
| [<c140550a>] work_notifysig+0x35/0x3b
|
| -> #1 (&tty->legacy_mutex/1){+.+...}:
| [<c107fe74>] lock_acquire+0x84/0x190
| [<c140276c>] mutex_lock_nested+0x6c/0x2f0
| [<c14051e6>] tty_lock_nested+0x36/0x80
| [<c1405279>] tty_lock_pair+0x29/0x70
| [<c12e0bb8>] tty_release+0x118/0x470
| [<c1105e28>] __fput+0xd8/0x270
| [<c1105fcd>] ____fput+0xd/0x10
| [<c1051dd9>] task_work_run+0xb9/0xf0
| [<c1002a51>] do_notify_resume+0x51/0x80
| [<c140550a>] work_notifysig+0x35/0x3b
|
| -> #0 (&tty->legacy_mutex){+.+.+.}:
| [<c107f3c9>] __lock_acquire+0x1189/0x16a0
| [<c107fe74>] lock_acquire+0x84/0x190
| [<c140276c>] mutex_lock_nested+0x6c/0x2f0
| [<c14051e6>] tty_lock_nested+0x36/0x80
| [<c140523f>] tty_lock+0xf/0x20
| [<c12df8e4>] __tty_hangup+0x54/0x410
| [<c12dfcb2>] do_tty_hangup+0x12/0x20
| [<c104f763>] process_one_work+0x1a3/0x5e0
| [<c104fec9>] worker_thread+0x119/0x3a0
| [<c1055084>] kthread+0x94/0xa0
| [<c140ca37>] ret_from_kernel_thread+0x1b/0x28
|
|other info that might help us debug this:
|
|Chain exists of:
| &tty->legacy_mutex --> &tty->legacy_mutex/1 --> (&tty->hangup_work)
|
| Possible unsafe locking scenario:
|
| CPU0 CPU1
| ---- ----
| lock((&tty->hangup_work));
| lock(&tty->legacy_mutex/1);
| lock((&tty->hangup_work));
| lock(&tty->legacy_mutex);
|
| *** DEADLOCK ***
Before the path mentioned tty_ldisc_release() look like this:
| tty_ldisc_halt(tty);
| tty_ldisc_flush_works(tty);
| tty_lock();
As it can be seen, it first flushes the workqueue and then grabs the
tty_lock. Now we grab the lock first:
| tty_lock_pair(tty, o_tty);
| tty_ldisc_halt(tty);
| tty_ldisc_flush_works(tty);
so lockdep's complaint seems valid.
The earlier version of this patch took the ldisc_mutex since the other
user of tty_ldisc_flush_works() (tty_set_ldisc()) did this.
Peter Hurley then said that it is should not be requried. Since it
wasn't done earlier, I dropped this part.
The code under tty_ldisc_kill() was executed earlier with the tty lock
taken so it is taken again.
I was able to reproduce the deadlock on v3.8-rc1, this patch fixes the
problem in my testcase. I didn't notice any problems so far.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Bryan O'Donoghue <bryan.odonoghue.lkml@nexus-software.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1baee58638fc58248625255f5c5fcdb987f11b1f upstream.
Don't oops seems proper.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ad4e1a7caf937ad395ced585ca85a7d14395dc80 upstream.
If index++ calculates from 0, the checking condition of "while
(index++)" fails & it doesn't check any more. It doesn't follow
the loop that used at here.
Replace it by endless loop at here. Then it keeps parsing
"gpio-ranges" property until it ends.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 30f359a6f9da65a66de8cadf959f0f4a0d498bba upstream.
This patch fixes a bug where a handful of informational / control CDBs
that should be allowed during ALUA access state Standby/Offline/Transition
where incorrectly returning CHECK_CONDITION + ASCQ_04H_ALUA_TG_PT_*.
This includes INQUIRY + REPORT_LUNS, which would end up preventing LUN
registration when LUN scanning occured during these ALUA access states.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d4a2618fa77b5e58ec15342972bd3505a1c3f551 upstream.
If a result of the SMP discover function is PHY VACANT,
the content of discover response structure (dr) is not valid.
It sometimes happens that dr->attached_sas_addr can contain
even SAS address of other phy. In such case an invalid phy
is created, what causes NULL pointer dereference during
destruction of expander's phys.
So if a result of SMP function is PHY VACANT, the content of discover
response structure (dr) must not be copied to phy structure.
This patch fixes the following bug:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000030
IP: [<ffffffff811c9002>] sysfs_find_dirent+0x12/0x90
Call Trace:
[<ffffffff811c95f5>] sysfs_get_dirent+0x35/0x80
[<ffffffff811cb55e>] sysfs_unmerge_group+0x1e/0xb0
[<ffffffff813329f4>] dpm_sysfs_remove+0x24/0x90
[<ffffffff8132b0f4>] device_del+0x44/0x1d0
[<ffffffffa016fc59>] sas_rphy_delete+0x9/0x20 [scsi_transport_sas]
[<ffffffffa01a16f6>] sas_destruct_devices+0xe6/0x110 [libsas]
[<ffffffff8107ac7c>] process_one_work+0x16c/0x350
[<ffffffff8107d84a>] worker_thread+0x17a/0x410
[<ffffffff81081b76>] kthread+0x96/0xa0
[<ffffffff81464944>] kernel_thread_helper+0x4/0x10
Signed-off-by: Lukasz Dorau <lukasz.dorau@intel.com>
Signed-off-by: Pawel Baldysiak <pawel.baldysiak@intel.com>
Reviewed-by: Maciej Patelczyk <maciej.patelczyk@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 54683441a92ebe20c5282465ea6f21e5e74d2974 upstream.
This reverts commit b6fc28a158076ca2764edc9a6d1e1402f56e1c0c.
This commit is reported to cause a regression in the support for some
revisions of 4313 ePA devices.
http://marc.info/?l=linux-wireless&m=136360340200943&w=2
Conflicts:
drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c
Reported-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 765024697807ad1e1cac332aa891253ca4a339da upstream.
cyclic DMA is only used by audio which needs DMA to be started without a
delay.
If the DMA for audio is started using the tasklet we experience random
channel switch (to be more precise: channel shift).
Reported-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c12f9ea28e9fbe7b1f4cefc953bee33298370683 upstream.
This reverts commit 77e372a3d82e5e4878ce1962207edd766773cc76.
Checking for disabled resources board breaks detection pnp on another
board "AMI UEFI implementation (Version: 0406 Release Date: 06/06/2012)".
I'm working with the reporter of the original bug to write and test
a better fix.
https://bugzilla.redhat.com/show_bug.cgi?id=928246
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 83589b30f1e1dc9898986293c9336b8ce1705dec upstream.
BugLink: http://bugs.launchpad.net/bugs/1128840
It appears that when this register read fails it never recovers, so
I think there is no need to repeat the same error message ad infinitum.
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: linux-wireless@vger.kernel.org
Cc: users@rt2x00.serialmonkey.com
Cc: netdev@vger.kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 21de979ecfc7b7f9442f8aea9a54b3ab670d0151 upstream.
We are waiting on first scan command of internal scan request
before association, so we should complete on last internal scan
command response.
Tested-by: Daniel Drake <dsd@laptop.org>
Tested-by: Marco Cesarano <marco@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 904c680c7bf016a8619a045850937427f8d7368c upstream.
The VFIO_DEVICE_SET_IRQS ioctl takes a start and count parameter, both
of which are unsigned. We attempt to bounds check these, but fail to
account for the case where start is a very large number, allowing
start + count to wrap back into the valid range. Bounds check both
start and start + count.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e2409d83434d77874b461b78af6a19cd6e6a1280 upstream.
It would cause no link after suspending or shutdowning when the
nic changes the speed to 10M and connects to a link partner which
forces the speed to 100M.
Check the link partner ability to determine which speed to set.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5559ecadad5a73b27f863e92f4b4f369501dce6f upstream.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=44156
Reported-by: Alan Zimmerman <alan.zimm@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 01e3a8feb40e54b962a20fa7eb595c5efef5e109 upstream.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=31522#c35
[Note: There are more than one broken setups in the bug. This fixes one.]
Reported-by: Martins <andrissr@inbox.lv>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1ffff60320879830e469e26062c18f75236822ba upstream.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=59628
Reported-by: Roland Gruber <post@rolandgruber.de>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6e45eb12fd1c741d556bf264ee98853b5f3104e5 upstream.
Boot_freq is for saving booting freq. But exynos_cpufreq_cpu_init
is called in hotplug. If boot_freq is existed in exynos_cpufreq_cpu_init,
boot_freq could be changed.
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 51c94491c82c3d9029f6e87a1a153db321d88e35 upstream.
Fix memory leak - don't forget to kfree ACPI object when returning from
msi_wmi_notify() after suppressing key event.
Signed-off-by: Maxim Mikityanskiy <maxtram95@gmail.com>
Acked-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: Lee, Chun-Yi <jlee@suse.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit da28d966f6aa942ae836d09729f76a1647932309 upstream.
The return code from the registration of the thermal class is used to
unallocate resources, but this failure isn't passed back to the caller of
thermal_init. Return this failure back to the caller.
This bug was introduced in changeset 4cb18728 which overwrote the return code
when the variable was re-used to catch the return code of the registration of
the genetlink thermal socket family.
Signed-off-by: Richard Guy Briggs <rbriggs@redhat.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Cc: Jonghwan Choi <jhbird.choi@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b8178f130e25c1bdac1c33e0996f1ff6e20ec08e upstream.
This reverts commit 8c33f51df406e1a1f7fa4e9b244845b7ebd61fa6.
Conflicts:
drivers/acpi/pci_root.c
This commit broke some pre-1.1 PCIe devices by leaving them with
ASPM enabled. Previously, we had disabled ASPM on these devices
because many of them don't implement it correctly (per 149e1637).
Requesting _OSC control early means that aspm_disabled may be set
before we scan the PCI bus and configure link ASPM state. But the
ASPM configuration currently skips the check for pre-PCIe 1.1 devices
when aspm_disabled is set, like this:
acpi_pci_root_add
acpi_pci_osc_support
if (flags != base_flags)
pcie_no_aspm
aspm_disabled = 1
pci_acpi_scan_root
...
pcie_aspm_init_link_state
pcie_aspm_sanity_check
if (!aspm_disabled)
/* check for pre-PCIe 1.1 device */
Therefore, setting aspm_disabled early means that we leave ASPM enabled
on these pre-PCIe 1.1 devices, which is a regression for some devices.
The best fix would be to clean up the ASPM init so we can evaluate
_OSC before scanning the bug (that way boot-time and hot-add discovery
will work the same), but that requires significant rework.
For now, we'll just revert the _OSC change as the lowest-risk fix.
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=55211
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 27b7c63a7c509d797c151e95a641e1d94d94bbd9 upstream.
ERROR: "__build_bug_on_failed" [drivers/gpu/drm/i915/i915.ko] undefined!
Originally reported at http://www.gossamer-threads.com/lists/linux/kernel/1631803
FDO bug #62775
This needs to be backported to both 3.7 and 3.8 stable trees. Doesn't apply straight,
but it's a quick change.
Signed-off-by: Lauri Kasanen <cand@gmx.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=62775
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1812a3db0874be1d1524086da9e84397b800f546 upstream.
This change properly enables the "requester" in G200ER cards that is
responsible for getting pixels out of memory and clocking them out to
the screen.
Signed-off-by: Christopher Harvey <charvey@matrox.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d47cbd5bcee7c7a08fc0283dda465375fa1b1fda upstream.
Commit 4f31f5b19eb0418a847b989abc9ac22af1991fe2
"PM / crypto / ux500: Use struct dev_pm_ops for power management"
add a new line to the driver struct but missed to add a
trailing comma, causing build errors when crypto is
selected. This adds the missing comma.
This was not noticed until now because the crypto block
is not in the ux500 defconfig. A separate patch will
be submitted to fix this.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Magnus Myrstedt <magnus.p.persson@stericsson.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c7426bce5933d16b492a34e42ae77e26fceddff6 upstream.
Fix obvious typo introduced in commit e121aefa7d9f10eee5cf26ed47129237a05d940b
("remoteproc: fix missing CONFIG_FW_LOADER configurations").
Signed-off-by: Robert Tivy <rtivy@ti.com>
[cc stable, slight subject change]
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cde42e076c1cdd69a1f955d66ff6596bad3d2105 upstream.
Remove the vdev entry from the list before freeing it,
otherwise rproc->vdevs will explode.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Acked-by: Ido Yariv <ido@wizery.com>
[edit subject, minor commit log edit, cc stable]
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1cd425b660bd5b4f41b9175b0b7bf3828ce88144 upstream.
Fixes coherent memory leakage, caused by non-deallocated
firmware image chunk.
Signed-off-by: Dmitry Tarnyagin <dmitry.tarnyagin@stericsson.com>
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Acked-by: Ido Yariv <ido@wizery.com>
[slightly edit subject and commit log]
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c10b90d85a5126d25c89cbaa50dc9fdd1c4d001a upstream.
Even in failed case of pm_runtime_get_sync, the usage_count
is incremented. In order to keep the usage_count with correct
value and runtime power management to behave correctly, call
pm_runtime_put_noidle in such case.
In __hwspin_lock_request, module_put is also called before
return in pm_runtime_get_sync failed case.
Signed-off-by Liu Chuansheng <chuansheng.liu@intel.com>
Signed-off-by: Li Fei <fei.li@intel.com>
[edit commit log]
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 901ceba4e81e9dd6b4a3c4c37ee22000a6c5c65f upstream.
Limit the channel number in scan request, or the driver scan
config structure memory will be overflowed.
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b55f84e2d527182e7c611d466cd0bb6ddce201de upstream.
There is a quirk patch 5e5a4f5d5a08c9c504fe956391ac3dae2c66556d
"ata_piix: make DVD Drive recognisable on systems with Intel Sandybridge
chipsets(v2)" fixing the 4 ports IDE controller 32bit PIO mode.
We've hit a problem with DVD not recognized on Haswell Desktop platform which
includes Lynx Point 2-port SATA controller.
This quirk patch disables 32bit PIO on this controller in IDE mode.
v2: Change spelling error in statememnt pointed by Sergei Shtylyov.
v3: Change comment statememnt and spliting line over 80 characters pointed by
Libor Pechacek and also rebase the patch against 3.8-rc7 kernel.
Tested-by: Lee, Chun-Yi <jlee@suse.com>
Signed-off-by: Youquan Song <youquan.song@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit de7d5f729c72638f41d7c17487bccb1c570ff144 upstream.
The runtime PM of PCIe ports turns out to be quite fragile, as in
some cases things work while in some other cases they don't and we
don't seem to have a good way to determine whether or not they are
going to work in advance.
For this reason, avoid enabling runtime PM for PCIe ports by
keeping their runtime PM reference counters always above 0 for the
time being.
When a PCIe port is suspended, it can no longer report events like
hotplug, so hotplug below the port may not work, as in the bug
report below.
[bhelgaas: changelog, stable]
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=53811
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 24ad0ef9c8b946ed2abe681e4e44f4a1e643d882 upstream.
It turns out that the _Lxx control methods provided by some BIOSes
clear the PME Status bit of PCI devices they handle, which means that
pci_acpi_wake_dev() cannot really use that bit to check whether or
not the device has signalled wakeup.
One symptom of the problem is, for example, that when an affected PCI
USB controller is runtime-suspended, then plugging in a new USB device
into one of the controller's ports will not wake up the controller,
which should happen.
For this reason, make pci_acpi_wake_dev() always attempt to resume
the device it is called for regardless of the device's PME Status bit
value (that bit still has to be cleared if set at this point,
though).
Reported-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8e725c7f8a60feaa88edacd4dee2c754d5ae7706 upstream.
Commit 803739d25c2343da6d2f95eebdcbc08bf67097d4 ("[libata] replace
sata_settings with devslp_timing"), which was also Cc: stable, used a
stack buffer to receive data from ata_read_log_page(), which triggers
the following warning:
ahci 0000:00:1f.2: DMA-API: device driver maps memory fromstack [addr=ffff880140469948]
Fix this by using ap->sector_buf instead of a stack buffer.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a32450e127fc6e5ca6d958ceb3cfea4d30a00846 upstream.
The Slimtype DVD A DS8A8SH drive locks up when max sector is smaller than
65535, and the blow backtrace is observed on locking up:
INFO: task flush-8:32:1130 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
flush-8:32 D ffffffff8180cf60 0 1130 2 0x00000000
ffff880273aef618 0000000000000046 0000000000000005 ffff880273aee000
ffff880273aee000 ffff880273aeffd8 ffff880273aee010 ffff880273aee000
ffff880273aeffd8 ffff880273aee000 ffff88026e842ea0 ffff880274a10000
Call Trace:
[<ffffffff8168fc2d>] schedule+0x5d/0x70
[<ffffffff8168fccc>] io_schedule+0x8c/0xd0
[<ffffffff81324461>] get_request+0x731/0x7d0
[<ffffffff8133dc60>] ? cfq_allow_merge+0x50/0x90
[<ffffffff81083aa0>] ? wake_up_bit+0x40/0x40
[<ffffffff81320443>] ? bio_attempt_back_merge+0x33/0x110
[<ffffffff813248ea>] blk_queue_bio+0x23a/0x3f0
[<ffffffff81322176>] generic_make_request+0xc6/0x120
[<ffffffff81322308>] submit_bio+0x138/0x160
[<ffffffff811d7596>] ? bio_alloc_bioset+0x96/0x120
[<ffffffff811d1f61>] submit_bh+0x1f1/0x220
[<ffffffff811d48b8>] __block_write_full_page+0x228/0x340
[<ffffffff811d3650>] ? attach_nobh_buffers+0xc0/0xc0
[<ffffffff811d8960>] ? I_BDEV+0x10/0x10
[<ffffffff811d8960>] ? I_BDEV+0x10/0x10
[<ffffffff811d4ab6>] block_write_full_page_endio+0xe6/0x100
[<ffffffff811d4ae5>] block_write_full_page+0x15/0x20
[<ffffffff811d9268>] blkdev_writepage+0x18/0x20
[<ffffffff81142527>] __writepage+0x17/0x40
[<ffffffff811438ba>] write_cache_pages+0x34a/0x4a0
[<ffffffff81142510>] ? set_page_dirty+0x70/0x70
[<ffffffff81143a61>] generic_writepages+0x51/0x80
[<ffffffff81143ab0>] do_writepages+0x20/0x50
[<ffffffff811c9ed6>] __writeback_single_inode+0xa6/0x2b0
[<ffffffff811ca861>] writeback_sb_inodes+0x311/0x4d0
[<ffffffff811caaa6>] __writeback_inodes_wb+0x86/0xd0
[<ffffffff811cad43>] wb_writeback+0x1a3/0x330
[<ffffffff816916cf>] ? _raw_spin_lock_irqsave+0x3f/0x50
[<ffffffff811b8362>] ? get_nr_inodes+0x52/0x70
[<ffffffff811cb0ac>] wb_do_writeback+0x1dc/0x260
[<ffffffff8168dd34>] ? schedule_timeout+0x204/0x240
[<ffffffff811cb232>] bdi_writeback_thread+0x102/0x2b0
[<ffffffff811cb130>] ? wb_do_writeback+0x260/0x260
[<ffffffff81083550>] kthread+0xc0/0xd0
[<ffffffff81083490>] ? kthread_worker_fn+0x1b0/0x1b0
[<ffffffff8169a3ec>] ret_from_fork+0x7c/0xb0
[<ffffffff81083490>] ? kthread_worker_fn+0x1b0/0x1b0
The above trace was triggered by
"dd if=/dev/zero of=/dev/sr0 bs=2048 count=32768"
It was previously working by accident, since another bug introduced
by 4dce8ba94c7 (libata: Use 'bool' return value for ata_id_XXX) caused
all drives to use maxsect=65535.
Signed-off-by: Shan Hai <shan.hai@windriver.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f01fc1a82c2ee68726b400fadb156bd623b5f2f1 upstream.
ixgbe_notify_dca cannot be called before driver registration
because it expects driver's klist_devices to be allocated and
initialized. While on it make sure debugfs files are removed
when registration fails.
Signed-off-by: Jakub Kicinski <jakub.kicinski@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2cfda637e29ce9e3df31b59f64516b2e571cc985 upstream.
Matthew found that 3.8.3 is having problems with an old (ancient)
PCI-to-EISA bridge, the Intel 82375. It worked with the 3.2 kernel.
He identified the 82375, but doesn't assign the struct resource *res
pointer inside the struct eisa_root_device, and panics.
pci_eisa_init() was using bus->resource[] directly instead of
pci_bus_resource_n(). The bus->resource[] array is a PCI-internal
implementation detail, and after commit 45ca9e97 (PCI: add helpers for
building PCI bus resource lists) and commit 0efd5aab (PCI: add struct
pci_host_bridge_window with CPU/bus address offset), bus->resource[] is not
used for PCI root buses any more.
The 82375 is a subtractive-decode PCI device, so handle it the same
way we handle PCI-PCI bridges in subtractive-decode mode in
pci_read_bridge_bases().
[bhelgaas: changelog]
Reported-by: Matthew Whitehead <mwhitehe@redhat.com>
Tested-by: Matthew Whitehead <mwhitehe@redhat.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c5fb301ae83bec6892e54984e6ec765c47df8e10 upstream.
Matthew reported kernels fail the pci_eisa probe and are later successful
with the virtual_eisa_root_init force probe without slot0.
The reason for that is: PNP probing is before pci_eisa_init gets called
as pci_eisa_init is called via pci_driver.
pnp 00:0f has 0xc80 - 0xc84 reserved.
[ 9.700409] pnp 00:0f: [io 0x0c80-0x0c84]
so eisa_probe will fail from pci_eisa_init
==>eisa_root_register
==>eisa_probe path.
as force_probe is not set in pci_eisa_root, it will bail early when
slot0 is not probed and initialized.
Try to use subsys_initcall_sync instead, and will keep following sequence:
pci_subsys_init
pci_eisa_init_early
pnpacpi_init/isapnp_init
After this patch EISA can be initialized properly, and PNP overlapping
resource will not be reserved.
[ 10.104434] system 00:0f: [io 0x0c80-0x0c84] could not be reserved
Reported-by: Matthew Whitehead <mwhitehe@redhat.com>
Tested-by: Matthew Whitehead <mwhitehe@redhat.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e24b0bfa2f0446ffaad2661040be23668133aef8 upstream.
This reverts commit 0ef1594c017521ea89278e80fe3f80dafb17abde.
This patch introduced a few races which cannot be easily fixed with a
small follow-up patch. Furthermore, the SoC with the broken hardware
register, which this patch intended to add support for, can only be used
with device trees, which this driver currently does not support.
[ Here is the discussion that led to this "revert" patch:
https://lkml.org/lkml/2013/4/3/176 ]
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a8ec3a662921220fc058ed6f7f3674697876d218 upstream.
If first drm_open fails, the error-handling path will
incorrectly restore inode's mapping to NULL. This can
cause the crash later on. Fix by separately storing
away mapping pointers that drm_open can touch and
restore each from its own respective variable if the
call fails.
Fixes: https://bugzilla.novell.com/show_bug.cgi?id=807850
(thanks to Michal Hocko for investigating investigating and
finding the root cause of the bug)
Reference:
http://lists.freedesktop.org/archives/dri-devel/2013-March/036564.html
v2: Use one variable to store file and inode mapping
since they are the same at the function entry.
Fix spelling mistakes in commit message.
v3: Add reference to the original bug report.
Reported-by: Marco Munderloh <munderl@tnt.uni-hannover.de>
Tested-by: Marco Munderloh <munderl@tnt.uni-hannover.de>
Signed-off-by: Ilija Hadzic <ihadzic@research.bell-labs.com>
Cc: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 637f44d24f8868ee5a597a99e7874fdd150d4cba upstream.
commit f40ebd6bcbbd0d30591f42dc16be52b5086a366b
Author: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Date: Tue Mar 5 14:24:48 2013 +0100
drm/i915: Turn off hsync and vsync on ADPA when disabling crt
properly disabled the hsync/vsync logic at disable time, but neglected
to re-enable them at enable time.
v2: In the enable hook, restore the connector's expected DPMS level
instead of forcing ON. Do this by stashing a back pointer to the
connector in the crt (suggested by danvet) since otherwise it's awkward
to look up.
Signed-off-by: Adam Jackson <ajax@redhat.com>
[danvet: Added more verbose commit citation and cc: stable tag. Also,
make it compile. Then self-lart and try to assign the right pointer.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b43decd2c513ae44a5462a1a4c2622f0fa77c9e0 upstream.
If there are no channels, chan would never end up being NULL,
and so the null pointer check would fail.
Solve this by initializing chan to NULL, and iterating over temp instead.
Fixes oops when running intel-gpu-tools/tests/kms_flip, which attempts to
do some intel ioctl's on a nouveau device.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9afd9b7090225d78ef56423a2ff65354dc38f1b1 upstream.
The irq domain was implemented but the device tree
node was not transmitted to irq_domain_add_simple().
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
