| Age | Commit message (Collapse) | Author |
|---|
|
commit 9c6d196d5aa35e07482f23c3e37755e7a82140e0 upstream.
Don't fail the initialization check for the platform_data
if there is avaiable an associated device tree node.
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit abce9ac292e13da367bbd22c1f7669f988d931ac upstream.
tpm_write calls tpm_transmit without checking the return value and
assigns the return value unconditionally to chip->pending_data, even if
it's an error value.
This causes three bugs.
So if we write to /dev/tpm0 with a tpm_param_size bigger than
TPM_BUFSIZE=0x1000 (e.g. 0x100a)
and a bufsize also bigger than TPM_BUFSIZE (e.g. 0x100a)
tpm_transmit returns -E2BIG which is assigned to chip->pending_data as
-7, but tpm_write returns that TPM_BUFSIZE bytes have been successfully
been written to the TPM, altough this is not true (bug #1).
As we did write more than than TPM_BUFSIZE bytes but tpm_write reports
that only TPM_BUFSIZE bytes have been written the vfs tries to write
the remaining bytes (in this case 10 bytes) to the tpm device driver via
tpm_write which then blocks at
/* cannot perform a write until the read has cleared
either via tpm_read or a user_read_timer timeout */
while (atomic_read(&chip->data_pending) != 0)
msleep(TPM_TIMEOUT);
for 60 seconds, since data_pending is -7 and nobody is able to
read it (since tpm_read luckily checks if data_pending is greater than
0) (#bug 2).
After that the remaining bytes are written to the TPM which are
interpreted by the tpm as a normal command. (bug #3)
So if the last bytes of the command stream happen to be a e.g.
tpm_force_clear this gets accidentally sent to the TPM.
This patch fixes all three bugs, by propagating the error code of
tpm_write and returning -E2BIG if the input buffer is too big,
since the response from the tpm for a truncated value is bogus anyway.
Moreover it returns -EBUSY to userspace if there is a response ready to be
read.
Signed-off-by: Peter Huewe <peter.huewe@infineon.com>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8edc0e624db3756783233e464879eb2e3b904c13 upstream.
This patch originated from Hiroaki SHIMODA but has been modified
by Intel with some minor cleanups and additional commit log text.
Denys Fedoryshchenko and others reported Tx stalls on e1000e with
BQL enabled. Issue was root caused to hardware delays. They were
introduced because some of the e1000e hardware with transmit
writeback bursting enabled, waits until the driver does an
explict flush OR there are WTHRESH descriptors to write back.
Sometimes the delays in question were on the order of seconds,
causing visible lag for ssh sessions and unacceptable tx
completion latency, especially for BQL enabled kernels.
To avoid possible Tx stalls, change WTHRESH back to 1.
The current plan is to investigate a method for re-enabling
WTHRESH while not harming BQL, but those patches will be later
for net-next if they work.
please enqueue for stable since v3.3 as this bug was introduced in
commit 3f0cfa3bc11e7f00c9994e0f469cbc0e7da7b00c
Author: Tom Herbert <therbert@google.com>
Date: Mon Nov 28 16:33:16 2011 +0000
e1000e: Support for byte queue limits
Changes to e1000e to use byte queue limits.
Reported-by: Denys Fedoryshchenko <denys@visp.net.lb>
Tested-by: Denys Fedoryshchenko <denys@visp.net.lb>
Signed-off-by: Hiroaki SHIMODA <shimoda.hiroaki@gmail.com>
CC: eric.dumazet@gmail.com
CC: therbert@google.com
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bf7a01bf7987b63b121d572b240c132ec44129c4 upstream.
The NAND_CHIPOPTIONS_MSK has limited utility and is causing real bugs. It
silently masks off at least one flag that might be set by the driver
(NAND_NO_SUBPAGE_WRITE). This breaks the GPMI NAND driver and possibly
others.
Really, as long as driver writers exercise a small amount of care with
NAND_* options, this mask is not necessary at all; it was only here to
prevent certain options from accidentally being set by the driver. But the
original thought turns out to be a bad idea occasionally. Thus, kill it.
Note, this patch fixes some major gpmi-nand breakage.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: Huang Shijie <shijie8@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
index a11253a..c429abd 100644
|
|
commit dabdaf0caa3af520dbc1df87b2fb4e77224037bd upstream.
The device had an undocumented "feature": it can provide a sequence of
spurious link-down status data even if the link is up all the time.
A sequence of 10 was seen so update the link state only after the device
reports the same link state 20 times.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reported-by: Michael Leun <lkml20120218@newton.leun.net>
Tested-by: Michael Leun <lkml20120218@newton.leun.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0c96c65b48fba3ffe9822a554cbc0cd610765cd5 upstream.
The dithering introduced in
commit 3b5c78a35cf7511c15e09a9b0ffab290a42d9bcf
Author: Adam Jackson <ajax@redhat.com>
Date: Tue Dec 13 15:41:00 2011 -0800
drm/i915/dp: Dither down to 6bpc if it makes the mode fit
stores the INTEL_MODE_DP_FORCE_6BPC flag in the private_flags of the
adjusted mode, while i9xx_crtc_mode_set() and ironlake_crtc_mode_set() use
the original mode, without the flag, so it would never have any
effect. However, the BPC was clamped by VBT settings, making things work by
coincidence, until that part was removed in
commit 4344b813f105a19f793f1fd93ad775b784648b95
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Aug 10 11:10:20 2012 +0200
Use adjusted_mode instead of mode when checking for
INTEL_MODE_DP_FORCE_6BPC to make the flag have effect.
v2: Don't forget to fix this in i9xx_crtc_mode_set() also, pointed out by
Daniel both before and after sending the first patch.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=47621
CC: Adam Jackson <ajax@redhat.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 26b6e44afb58432a5e998da0343757404f9de9ee upstream.
A previous patch, namely:
commit bf97b276ca04cee9ab65ffd378fa8e6aedd71ff6
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Apr 11 20:42:41 2012 +0200
drm/i915: implement w/a for incorrect guarband clipping
accidentally set bit 5 in 3D_CHICKEN, which has nothing to do with
clipping. This patch changes it to be set in 3D_CHICKEN3, where it
belongs.
The game "Dante" demonstrates random clipping issues when guardband
clipping is enabled and bit 5 of 3D_CHICKEN3 isn't set. So the
workaround is actually necessary.
Acked-by: Paul Menzel <paulepanter@users.sourceforge.net>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Oliver McFadden <oliver.mcfadden@linux.intel.com>
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c77d7162a7ae451c2e895d7ef7fbeb0906107472 upstream.
starting an old X server causes a kernel BUG since commit 1b50247a8d:
------------[ cut here ]------------
kernel BUG at drivers/gpu/drm/i915/i915_gem.c:3661!
invalid opcode: 0000 [#1] SMP
Modules linked in: snd_seq_dummy snd_seq_oss snd_seq_midi_event snd_seq snd_seq_device snd_pcm_oss snd_mixer_oss uvcvideo
+videobuf2_core videodev videobuf2_vmalloc videobuf2_memops uhci_hcd ath9k mac80211 snd_hda_codec_realtek ath9k_common microcode
+ath9k_hw psmouse serio_raw sg ath cfg80211 atl1c lpc_ich mfd_core ehci_hcd snd_hda_intel snd_hda_codec snd_hwdep snd_pcm rtc_cmos
+snd_timer snd evdev eeepc_laptop snd_page_alloc sparse_keymap
Pid: 2866, comm: X Not tainted 3.5.6-rc1-eeepc #1 ASUSTeK Computer INC. 1005HA/1005HA
EIP: 0060:[<c12dc291>] EFLAGS: 00013297 CPU: 0
EIP is at i915_gem_entervt_ioctl+0xf1/0x110
EAX: f5941df4 EBX: f5940000 ECX: 00000000 EDX: 00020000
ESI: f5835400 EDI: 00000000 EBP: f51d7e38 ESP: f51d7e20
DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
CR0: 8005003b CR2: b760e0a0 CR3: 351b6000 CR4: 000007d0
DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
DR6: ffff0ff0 DR7: 00000400
Process X (pid: 2866, ti=f51d6000 task=f61af8d0 task.ti=f51d6000)
Stack:
00000001 00000000 f5835414 f51d7e84 f5835400 f54f85c0 f51d7f10 c12b530b
00000001 c151b139 c14751b6 c152e030 00000b32 00006459 00000059 0000e200
00000001 00000000 00006459 c159ddd0 c12dc1a0 ffffffea 00000000 00000000
Call Trace:
[<c12b530b>] drm_ioctl+0x2eb/0x440
[<c12dc1a0>] ? i915_gem_init+0xe0/0xe0
[<c1052b2b>] ? enqueue_hrtimer+0x1b/0x50
[<c1053321>] ? __hrtimer_start_range_ns+0x161/0x330
[<c10530b3>] ? lock_hrtimer_base+0x23/0x50
[<c1053163>] ? hrtimer_try_to_cancel+0x33/0x70
[<c12b5020>] ? drm_version+0x90/0x90
[<c10ca171>] vfs_ioctl+0x31/0x50
[<c10ca2e4>] do_vfs_ioctl+0x64/0x510
[<c10535de>] ? hrtimer_nanosleep+0x8e/0x100
[<c1052c20>] ? update_rmtp+0x80/0x80
[<c10ca7c9>] sys_ioctl+0x39/0x60
[<c1433949>] syscall_call+0x7/0xb
Code: 83 c4 0c 5b 5e 5f 5d c3 c7 44 24 04 2c 05 53 c1 c7 04 24 6f ef 47 c1 e8 6e e0 fd ff c7 83 38 1e 00 00 00 00 00 00 e9 3f ff ff
+ff <0f> 0b eb fe 0f 0b eb fe 8d b4 26 00 00 00 00 0f 0b eb fe 8d b6
EIP: [<c12dc291>] i915_gem_entervt_ioctl+0xf1/0x110 SS:ESP 0068:f51d7e20
---[ end trace dd332ec083cbd513 ]---
The crash happens here in i915_gem_entervt_ioctl() :
3659 BUG_ON(!list_empty(&dev_priv->mm.active_list));
3660 BUG_ON(!list_empty(&dev_priv->mm.flushing_list));
-> 3661 BUG_ON(!list_empty(&dev_priv->mm.inactive_list));
3662 mutex_unlock(&dev->struct_mutex);
Quoting Chris :
"That BUG_ON there is silly and can simply be removed. The check is to
verify that no batches were submitted to the kernel whilst the UMS/GEM
client was suspended - to which the BUG_ONs are a crude approximation.
Furthermore, the checks are too late, since it means we attempted to
program the hardware whilst it was in an invalid state, the BUG_ONs are
the least of your concerns at that point."
Note that this regression has been introduced in
commit 1b50247a8ddde4af5aaa0e6bc125615372ce6c16
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Tue Apr 24 15:47:30 2012 +0100
drm/i915: Remove the list of pinned inactive objects
Signed-off-by: Willy Tarreau <w@1wt.eu>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Added note about the regressing commit and cc: stable.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 082918471139b07964967cfe5f70230909c82ae1 upstream.
radeon_i2c_fini() walks thru the list of I2C bus recs rdev->i2c_bus[]
to destroy each of them.
radeon_ext_tmds_enc_destroy() however also has code to destroy it's
associated I2C bus rec which has been obtained by radeon_i2c_lookup()
and is therefore also in the i2c_bus[] list.
This causes a double free resulting in a kernel panic when unloading
the radeon driver.
Removing destroy code from radeon_ext_tmds_enc_destroy() fixes this
problem.
agd5f: fix compiler warning
Signed-off-by: Egbert Eich <eich@suse.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e7d491a19d3e3aac544070293891a2542ae0c565 upstream.
This USB V.92/V.32bis Controllered Modem have the USB vendor ID 0x0572
and device ID 0x1340. It need the NO_UNION_NORMAL quirk to be recognized.
Reference:
http://www.conexant.com/servlets/DownloadServlet/DSH-201723-005.pdf?docid=1725&revid=5
See idVendor and idProduct in table 6-1. Device Descriptors
Signed-off-by: Jean-Christian de Rivaz <jc@eclis.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 17b572e82032bc246324ce136696656b66d4e3f1 upstream.
It is possible to miss data when using the kdb pager. The kdb pager
does not pay attention to the maximum column constraint of the screen
or serial terminal. This result is not incrementing the shown lines
correctly and the pager will print more lines that fit on the screen.
Obviously that is less than useful when using a VGA console where you
cannot scroll back.
The pager will now look at the kdb_buffer string to see how many
characters are printed. It might not be perfect considering you can
output ASCII that might move the cursor position, but it is a
substantially better approximation for viewing dmesg and trace logs.
This also means that the vt screen needs to set the kdb COLUMNS
variable.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 91502f099dfc5a1e8812898e26ee280713e1d002 upstream.
Clang complains that we are assigning a variable to itself. This should
be using bad_sectors like the similar earlier check does.
Bug has been present since 3.1-rc1. It is minor but could
conceivably cause corruption or other bad behaviour.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 249ee72249140fe5b9adc988f97298f0aa5db2fc upstream.
Using ieee80211_free_txskb for tx frames is required, since mac80211 clones
skbs for which socket tx status is requested.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 012a1211845eab69a5488d59eb87d24cc518c627 upstream.
As detailed in the thread titled "viafb PLL/clock tweaking causes XO-1.5
instability," enabling or disabling the IGA1/IGA2 clocks causes occasional
stability problems during suspend/resume cycles on this platform.
This is rather odd, as the documentation suggests that clocks have two
states (on/off) and the default (stable) configuration is configured to
enable the clock only when it is needed. However, explicitly enabling *or*
disabling the clock triggers this system instability, suggesting that there
is a 3rd state at play here.
Leaving the clock enable/disable registers alone solves this problem.
This fixes spurious reboots during suspend/resume behaviour introduced by
commit b692a63a.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b8c4321f3d194469007f5f5f2b34ec278c264a04 upstream.
Line 0 and 1 were both written to line 0 (on the display) and all subsequent
lines had an offset of -1. The result was that the last line on the display
was never overwritten by writes to /dev/fbN.
Signed-off-by: Alexander Holler <holler@ahsoftware.de>
Acked-by: Bernie Thompson <bernie@plugable.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cb6b6df111e46b9d0f79eb971575fd50555f43f4 upstream.
The commit 254d1a3f02ebc10ccc6e4903394d8d3f484f715e, titled
"xen/pv-on-hvm kexec: shutdown watches from old kernel" assumes that the
XenBus backend can deal with reading of values from:
"control/platform-feature-xs_reset_watches":
... a patch for xenstored is required so that it
accepts the XS_RESET_WATCHES request from a client (see changeset
23839:42a45baf037d in xen-unstable.hg). Without the patch for xenstored
the registration of watches will fail and some features of a PVonHVM
guest are not available. The guest is still able to boot, but repeated
kexec boots will fail."
Sadly this is not true when using a Xen 3.4 hypervisor and booting a PVHVM
guest. We end up hanging at:
err = xenbus_scanf(XBT_NIL, "control",
"platform-feature-xs_reset_watches", "%d", &supported);
This can easily be seen with guests hanging at xenbus_init:
NX (Execute Disable) protection: active
SMBIOS 2.4 present.
DMI: Xen HVM domU, BIOS 3.4.0 05/13/2011
Hypervisor detected: Xen HVM
Xen version 3.4.
Xen Platform PCI: I/O protocol version 1
... snip ..
calling xenbus_init+0x0/0x27e @ 1
Reverting the commit or using the attached patch fixes the issue. This fix
checks whether the hypervisor is older than 4.0 and if so does not try to
perform the read.
Fixes-Oracle-Bug: 14708233
Acked-by: Olaf Hering <olaf@aepfle.de>
[v2: Added a comment in the source code]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 899649b7d4ead76c19e39251ca886eebe3f811a8 upstream.
The virq_disabled flag tracks the userspace view of INTx masking
across interrupt mode changes, but we're not consistently applying
this to the interrupt and masking handler notion of the device.
Currently if the user sets DisINTx while in MSI or MSIX mode, then
returns to INTx mode (ex. rebooting a qemu guest), the hardware has
DisINTx+, but the management of INTx thinks it's enabled, making it
impossible to actually clear DisINTx. Fix this by updating the
handler state when INTx is re-enabled.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9dbdfd23b7638d054f3b0e70c64dfb9f297f2a9f upstream.
We need to be ready to recieve an interrupt as soon as we call
request_irq, so our eventfd context setting needs to be moved
earlier. Without this, an interrupt from our device or one
sharing the interrupt line can pass a NULL into eventfd_signal
and oops.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e4b11b89f9039ca97b2ed1b6efeb6749fbdeb252 upstream.
The qla2xxx firmware actually expects the task management response
code in a CTIO IOCB with SCSI status mode 1 to be in little-endian
byte order, ie the response code should be the first byte in the
sense_data[] array. The old code erroneously byte-swapped the
response code, which puts it in the wrong place on the wire and leads
to initiators thinking every task management request succeeds (since
they see 0 in the byte where they look for the response code).
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: Chad Dupuis <chad.dupuis@qlogic.com>
Cc: Arun Easi <arun.easi@qlogic.com>
Acked-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b32f4c7ed85c5cee2a21a55c9f59ebc9d57a2463 upstream.
This patch re-adds the ability to optionally run in buffered FILEIO mode
(eg: w/o O_DSYNC) for device backends in order to once again use the
Linux buffered cache as a write-back storage mechanism.
This logic was originally dropped with mainline v3.5-rc commit:
commit a4dff3043c231d57f982af635c9d2192ee40e5ae
Author: Nicholas Bellinger <nab@linux-iscsi.org>
Date: Wed May 30 16:25:41 2012 -0700
target/file: Use O_DSYNC by default for FILEIO backends
This difference with this patch is that fd_create_virtdevice() now
forces the explicit setting of emulate_write_cache=1 when buffered FILEIO
operation has been enabled.
(v2: Switch to FDBD_HAS_BUFFERED_IO_WCE + add more detailed
comment as requested by hch)
Reported-by: Ferry <iscsitmp@bananateam.nl>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 37bb7899ca366dc212b71b150e78566d04808cc0 upstream.
This patch fixes error cases within target_core_init_configfs() to
properly set ret = -ENOMEM before jumping to the out_global exception
path.
This was originally discovered with the following Coccinelle semantic
match information:
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function. A simplified version of the semantic match
that finds this problem is as follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7a3f369ce31694017996524a1cdb08208a839077 upstream.
The offset was not bumped back to the full size after writing the
header of the MODE SENSE response, so the last 1 or 2 bytes were
not copied.
On top of this, support zero-length requests by checking for the
return value of transport_kmap_data_sg.
Testcase: sg_raw -r20 /dev/sdb 5a 00 0a 00 00 00 00 00 14 00
last byte should be 0x1e
it is 0x00 without the patch
it is correct with the patch
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ffe7b0e9326d9c68f5688bef691dd49f1e0d3651 upstream.
INQUIRY processing already uses an on-heap bounce buffer for loopback,
but not for other fabrics. Switch this to a cheaper on-stack bounce
buffer, similar to the one used by MODE SENSE and REQUEST SENSE, and
use it unconditionally. With this in place, zero allocation length is
handled simply by checking the return address of transport_kmap_data_sg.
Testcase: sg_raw /dev/sdb 12 00 83 00 00 00
should fail with ILLEGAL REQUEST / INVALID FIELD IN CDB sense
does not fail without the patch
fails correctly with the series
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 790198f74c9d1b46b6a89504361b1a844670d050 upstream.
Fix two bugs of the /dev/fw* character device concerning the
FW_CDEV_IOC_GET_INFO ioctl with nonzero fw_cdev_get_info.bus_reset.
(Practically all /dev/fw* clients issue this ioctl right after opening
the device.)
Both bugs are caused by sizeof(struct fw_cdev_event_bus_reset) being 36
without natural alignment and 40 with natural alignment.
1) Memory corruption, affecting i386 userland on amd64 kernel:
Userland reserves a 36 bytes large buffer, kernel writes 40 bytes.
This has been first found and reported against libraw1394 if
compiled with gcc 4.7 which happens to order libraw1394's stack such
that the bug became visible as data corruption.
2) Information leak, affecting all kernel architectures except i386:
4 bytes of random kernel stack data were leaked to userspace.
Hence limit the respective copy_to_user() to the 32-bit aligned size of
struct fw_cdev_event_bus_reset.
Reported-by: Simon Kirby <sim@hostway.ca>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2e9c9dfde00a6466441e93033cf2c37f720bdacf upstream.
The sg struct is used without being initialized, which breaks
when CONFIG_DEBUG_SG is enabled.
Signed-off-by: Richard W.M. Jones <rjones@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bc977749e967daa56de1922cf4cb38525631c51c upstream.
Currently it is possible to unmap one more block than user requested to
due to the off-by-one error in unmap_region(). This is probably due to
the fact that the end variable despite its name actually points to the
last block to unmap + 1. However in the condition it is handled as the
last block of the region to unmap.
The bug was not previously spotted probably due to the fact that the
region was not zeroed, which has changed with commit
be1dd78de5686c062bb3103f9e86d444a10ed783. With that commit we were able
to corrupt the ext4 file system on 256M scsi_debug device with LBPRZ
enabled using fstrim.
Since the 'end' semantic is the same in several functions there this
commit just fixes the condition to use the 'end' variable correctly in
that context.
Reported-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5c1b10ab7f93d24f29b5630286e323d1c5802d5c upstream.
Properly account for I/O in transit before returning from the RESET call.
In the absense of this patch, we could have a situation where the host may
respond to a command that was issued prior to the issuance of the RESET
command at some arbitrary time after responding to the RESET command.
Currently, the host does not do anything with the RESET command.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cf0eb28d3ba60098865bf7dbcbfdd6b1cc483e3b upstream.
This patch increases the default for nopin_timeout to 15 seconds (wait
between sending a new NopIN ping) and nopin_response_timeout to 30 seconds
(wait for NopOUT response before failing the connection) in order to avoid
false positives by iSCSI Initiators who are not always able (under load) to
respond to NopIN echo PING requests within the current 5 second window.
False positives have been observed recently using Open-iSCSI code on v3.3.x
with heavy large-block READ workloads over small MTU 1 Gb/sec ports, and
increasing these values to more reasonable defaults significantly reduces
the possibility of false positive NopIN response timeout events under
this specific workload.
Historically these have been set low to initiate connection recovery as
soon as possible if we don't hear a ping back, but for modern v3.x code
on 1 -> 10 Gb/sec ports these new defaults make alot more sense.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 38b11bae6ba02da352340aff12ee25755977b222 upstream.
We've had reports in the past about this specific case, so it's time to
go ahead and explicitly set cache_dynamic_acls=1 for generate_node_acls=1
(TPG demo-mode) operation.
During normal generate_node_acls=0 operation with explicit NodeACLs ->
se_node_acl memory is persistent to the configfs group located at
/sys/kernel/config/target/$TARGETNAME/$TPGT/acls/$INITIATORNAME, so in
the generate_node_acls=1 case we want the reservation logic to reference
existing per initiator IQN se_node_acl memory (not to generate a new
se_node_acl), so go ahead and always set cache_dynamic_acls=1 when
TPG demo-mode is enabled.
Reported-by: Ronnie Sahlberg <ronniesahlberg@gmail.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 904753da183566c71211d23c169a80184648c121 upstream.
Fix a potential multiple spin-unlock -> deadlock scenario during the
overflow check within iscsit_build_sendtargets_resp() as found by
sparse static checking.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f25590f39d543272f7ae7b00d533359c8d7ff331 upstream.
This patch adds a missing iscsi_reject->ffffffff assignment within
iscsit_send_reject() code to properly follow RFC-3720 Section 10.17
Bytes 16 -> 19 for the PDU format definition of ISCSI_OP_REJECT.
We've not seen any initiators care about this bytes in practice, but
as Ronnie reported this was causing trouble with wireshark packet
decoding lets go ahead and fix this up now.
Reported-by: Ronnie Sahlberg <ronniesahlberg@gmail.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 67bfa9b60bd689601554526d144b21d529f78a09 upstream.
By enlarging the GPE storm threshold back to 20, that laptop's
EC works fine with interrupt mode instead of polling mode.
https://bugzilla.kernel.org/show_bug.cgi?id=45151
Reported-and-Tested-by: Francesco <trentini@dei.unipd.it>
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a520d52e99b14ba7db135e916348f12f2a6e09be upstream.
The Linux EC driver includes a mechanism to detect GPE storms,
and switch from interrupt-mode to polling mode. However, polling
mode sometimes doesn't work, so the workaround is problematic.
Also, different systems seem to need the threshold for detecting
the GPE storm at different levels.
ACPI_EC_STORM_THRESHOLD was initially 20 when it's created, and
was changed to 8 in 2.6.28 commit 06cf7d3c7 "ACPI: EC: lower interrupt storm
threshold" to fix kernel bug 11892 by forcing the laptop in that bug to
work in polling mode. However in bug 45151, it works fine in interrupt
mode if we lift the threshold back to 20.
This patch makes the threshold a module parameter so that user has a
flexible option to debug/workaround this issue.
The default is unchanged.
This is also a preparation patch to fix specific systems:
https://bugzilla.kernel.org/show_bug.cgi?id=45151
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8464dd52d3198dd05cafb005371d76e5339eb842 upstream.
On some systems, e.g., kzm9g, MMCIF interfaces can produce spurious
interrupts without any active request. To prevent the Oops, that results
in such cases, don't dereference the mmc request pointer until we make
sure, that we are indeed processing such a request.
Reported-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 15e8a8e42966162c207bb97ed55c803bc437eeae upstream.
mmc_gpio_request_ro() doesn't store the requested gpio in ctx->ro_gpio.
As a result, subsequent calls to mmc_gpio_get_ro() will always fail
with -ENOSYS because the gpio number isn't available to that function.
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c4c8eeb4df00aabb641553d6fbcd46f458e56cd9 upstream.
In some cases mmc_suspend_host() is not able to claim the
host and proceed with the suspend process. The core returns
-EBUSY to the host controller driver. Unfortunately, the
host controller driver does not pass on this information
to the PM core and hence the system suspend process continues.
ret = mmc_suspend_host(host->mmc);
if (ret) {
host->suspended = 0;
if (host->pdata->resume) {
ret = host->pdata->resume(dev, host->slot_id);
The return status from mmc_suspend_host() is overwritten by return
status from host->pdata->resume. So the original return status is lost.
In these cases the MMC core gets to an unexpected state
during resume and multiple issues related to MMC crop up.
1. Host controller driver starts accessing the device registers
before the clocks are enabled which leads to a prefetch abort.
2. A file copy thread which was launched before suspend gets
stuck due to the host not being reclaimed during resume.
To avoid such problems pass on the -EBUSY status to the PM core
from the host controller driver. With this change, MMC core
suspend might still fail but it does not end up making the
system unusable. Suspend gets aborted and the user can try
suspending the system again.
Signed-off-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Signed-off-by: Hebbar, Gururaja <gururaja.hebbar@ti.com>
Acked-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4d3d688da8e7016f15483e9319b41311e1db9515 upstream.
Unloading the omap2 nand driver missed to release the memory region which will
result in not being able to request it again if one want to load the driver
later on.
This patch fixes following error when loading omap2 module after unloading:
---8<---
~ $ rmmod omap2
~ $ modprobe omap2
[ 37.420928] omap2-nand: probe of omap2-nand.0 failed with error -16
~ $
--->8---
This error was introduced in 67ce04bf2746f8a1f8c2a104b313d20c63f68378 which
was the first commit of this driver.
Signed-off-by: Andreas Bießmann <andreas@biessmann.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7d9b110269253b1d5858cfa57d68dfc7bf50dd77 upstream.
Do not kfree() the mtd_info; it is handled in the mtd subsystem and
already freed by nand_release(). Instead kfree() the struct
omap_nand_info allocated in omap_nand_probe which was not freed before.
This patch fixes following error when unloading the omap2 module:
---8<---
~ $ rmmod omap2
------------[ cut here ]------------
kernel BUG at mm/slab.c:3126!
Internal error: Oops - BUG: 0 [#1] PREEMPT ARM
Modules linked in: omap2(-)
CPU: 0 Not tainted (3.6.0-rc3-00230-g155e36d-dirty #3)
PC is at cache_free_debugcheck+0x2d4/0x36c
LR is at kfree+0xc8/0x2ac
pc : [<c01125a0>] lr : [<c0112efc>] psr: 200d0193
sp : c521fe08 ip : c0e8ef90 fp : c521fe5c
r10: bf0001fc r9 : c521e000 r8 : c0d99c8c
r7 : c661ebc0 r6 : c065d5a4 r5 : c65c4060 r4 : c78005c0
r3 : 00000000 r2 : 00001000 r1 : c65c4000 r0 : 00000001
Flags: nzCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment user
Control: 10c5387d Table: 86694019 DAC: 00000015
Process rmmod (pid: 549, stack limit = 0xc521e2f0)
Stack: (0xc521fe08 to 0xc5220000)
fe00: c008a874 c00bf44c c515c6d0 200d0193 c65c4860 c515c240
fe20: c521fe3c c521fe30 c008a9c0 c008a854 c521fe5c c65c4860 c78005c0 bf0001fc
fe40: c780ff40 a00d0113 c521e000 00000000 c521fe84 c521fe60 c0112efc c01122d8
fe60: c65c4860 c0673778 c06737ac 00000000 00070013 00000000 c521fe9c c521fe88
fe80: bf0001fc c0112e40 c0673778 bf001ca8 c521feac c521fea0 c02ca11c bf0001ac
fea0: c521fec4 c521feb0 c02c82c4 c02ca100 c0673778 bf001ca8 c521fee4 c521fec8
fec0: c02c8dd8 c02c8250 00000000 bf001ca8 bf001ca8 c0804ee0 c521ff04 c521fee8
fee0: c02c804c c02c8d20 bf001924 00000000 bf001ca8 c521e000 c521ff1c c521ff08
ff00: c02c950c c02c7fbc bf001d48 00000000 c521ff2c c521ff20 c02ca3a4 c02c94b8
ff20: c521ff3c c521ff30 bf001938 c02ca394 c521ffa4 c521ff40 c009beb4 bf001930
ff40: c521ff6c 70616d6f b6fe0032 c0014f84 70616d6f b6fe0032 00000081 60070010
ff60: c521ff84 c521ff70 c008e1f4 c00bf328 0001a004 70616d6f c521ff94 0021ff88
ff80: c008e368 0001a004 70616d6f b6fe0032 00000081 c0015028 00000000 c521ffa8
ffa0: c0014dc0 c009bcd0 0001a004 70616d6f bec2ab38 00000880 bec2ab38 00000880
ffc0: 0001a004 70616d6f b6fe0032 00000081 00000319 00000000 b6fe1000 00000000
ffe0: bec2ab30 bec2ab20 00019f00 b6f539c0 60070010 bec2ab38 aaaaaaaa aaaaaaaa
Backtrace:
[<c01122cc>] (cache_free_debugcheck+0x0/0x36c) from [<c0112efc>] (kfree+0xc8/0x2ac)
[<c0112e34>] (kfree+0x0/0x2ac) from [<bf0001fc>] (omap_nand_remove+0x5c/0x64 [omap2])
[<bf0001a0>] (omap_nand_remove+0x0/0x64 [omap2]) from [<c02ca11c>] (platform_drv_remove+0x28/0x2c)
r5:bf001ca8 r4:c0673778
[<c02ca0f4>] (platform_drv_remove+0x0/0x2c) from [<c02c82c4>] (__device_release_driver+0x80/0xdc)
[<c02c8244>] (__device_release_driver+0x0/0xdc) from [<c02c8dd8>] (driver_detach+0xc4/0xc8)
r5:bf001ca8 r4:c0673778
[<c02c8d14>] (driver_detach+0x0/0xc8) from [<c02c804c>] (bus_remove_driver+0x9c/0x104)
r6:c0804ee0 r5:bf001ca8 r4:bf001ca8 r3:00000000
[<c02c7fb0>] (bus_remove_driver+0x0/0x104) from [<c02c950c>] (driver_unregister+0x60/0x80)
r6:c521e000 r5:bf001ca8 r4:00000000 r3:bf001924
[<c02c94ac>] (driver_unregister+0x0/0x80) from [<c02ca3a4>] (platform_driver_unregister+0x1c/0x20)
r5:00000000 r4:bf001d48
[<c02ca388>] (platform_driver_unregister+0x0/0x20) from [<bf001938>] (omap_nand_driver_exit+0x14/0x1c [omap2])
[<bf001924>] (omap_nand_driver_exit+0x0/0x1c [omap2]) from [<c009beb4>] (sys_delete_module+0x1f0/0x2ec)
[<c009bcc4>] (sys_delete_module+0x0/0x2ec) from [<c0014dc0>] (ret_fast_syscall+0x0/0x48)
r8:c0015028 r7:00000081 r6:b6fe0032 r5:70616d6f r4:0001a004
Code: e1a00005 eb0d9172 e7f001f2 e7f001f2 (e7f001f2)
---[ end trace 6a30b24d8c0cc2ee ]---
Segmentation fault
--->8---
This error was introduced in 67ce04bf2746f8a1f8c2a104b313d20c63f68378 which
was the first commit of this driver.
Signed-off-by: Andreas Bießmann <andreas@biessmann.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7bb9c75436212813b38700c34df4bbb6eb82debe upstream.
The code responsible for reading the version of the mirror bbt was
incorrectly using the descriptor of the main bbt.
Pass the mirror bbt descriptor to 'scan_read_raw' when reading the
version of the mirror bbt.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bb0a13a13411c4ce24c48c8ff3cdf7b48d237240 upstream.
If override size is too big, the module was actually loaded instead of
failing, because retval was not set.
This lead to memory corruption with the use of the freed structs nandsim
and nand_chip.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d1f55c680e5d021e7066f4461dd678d42af18898 upstream.
Update driver autcpu12-nvram.c so it compiles; map_read32/map_write32
no longer exist in the kernel so the driver is totally broken.
Additionally, map_info name passed to simple_map_init is incorrect.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c51803ddba10d80d9f246066802c6e359cf1d44c upstream.
We may cause a memory leak when the @types has more then one parser.
Take the `default_mtd_part_types` for example. The default_mtd_part_types has
two parsers now: `cmdlinepart` and `ofpart`.
Assume the following case:
The kernel command line sets the partitions like:
#gpmi-nand:20m(boot),20m(kernel),1g(rootfs),-(user)
But the devicetree file(such as arch/arm/boot/dts/imx28-evk.dts) also sets
the same partitions as the kernel command line does.
In the current code, the partitions parsed out by the `ofpart` will
overwrite the @pparts which has already set by the `cmdlinepart` parser,
and the the partitions parsed out by the `cmdlinepart` is missed.
A memory leak occurs.
So we should break the code as soon as we parse out the partitions,
In actually, this patch makes a priority order between the parsers.
If one parser has already parsed out the partitions successfully,
it's no need to use another parser anymore.
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 66dc81ecd71332783c92fb170950d5ddb43da461 upstream.
This dongle ships with the X1 Carbon, and has an AX88772B
usb to ethernet chip in it.
Signed-off-by: Quinlan Pfiffer <qpfiffer@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2425bb3d4016ed95ce83a90b53bd92c7f31091e4 upstream.
As em28xx-dvb will always be initialized asynchronously, there's
no need anymore for a separate thread to load the DRX-K firmware.
Fixes a known regression with kernel 3.6 with tda18271 driver
and asynchronous DRX-K firmware load.
Antti tested it with the following hardware:
Hauppauge WinTV HVR 930C
MaxMedia UB425-TC
PCTV QuatroStick nano (520e)
Tested-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f8f2ac9a76b0f80a6763ca316116a7bab8486997 upstream.
I can't even find how I figured this might be needed anymore. But sure
enough, the value I'm reading back on platforms doesn't match what the
docs recommends.
It seemed to fix Chris' GT1 in limited testing as well.
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 74d44445afb9f50126eba052adeb89827cee88f3 upstream.
... since finish_page_flip needs the vblank timestamp generated
in drm_handle_vblank. Somehow all the gmch platforms get it right,
but all the pch platform irq handlers get is wrong. Hooray for copy&
pasting!
Currently this gets papered over by a gross hack in finish_page_flip.
A second patch will remove that.
Note that without this, the new timestamp sanity checks in flip_test
occasionally get tripped up, hence the cc: stable tag.
Reviewed-by: mario.kleiner@tuebingen.mpg.de
Tested-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5bb61643f6a70d48de9cfe91ad0fee0d618b6816 upstream.
This was meant to be the purpose of the
intel_crtc_wait_for_pending_flips() function which is called whilst
preparing the CRTC for a modeset or before disabling. However, as Ville
Syrjala pointed out, we set the pending flip notification on the old
framebuffer that is no longer attached to the CRTC by the time we come
to flush the pending operations. Instead, we can simply wait on the
pending unpin work to be finished on this CRTC, knowning that the
hardware has therefore finished modifying the registers, before proceeding
with our direct access.
Fixes i-g-t/flip_test on non-pch platforms. pch platforms simply
schedule the flip immediately when the pipe is disabled, leading
to other funny issues.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Added i-g-t note and cc: stable]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4fe9f8e203fdad1524c04beb390f3c6099781ed9 upstream.
When a device is unplugged, wait for all processes that have opened the device
to close before deallocating the device.
Signed-off-by: Ratan Nalumasu <ratan@google.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fb6ca6d154cdcd53e7f27f8dbba513830372699b upstream.
There are so many quirks, lets just try and force
this for all RS690s. See:
https://bugs.freedesktop.org/show_bug.cgi?id=37679
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3a6d59df80897cc87812b6826d70085905bed013 upstream.
Fixes another system on:
https://bugs.freedesktop.org/show_bug.cgi?id=37679
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
