| Age | Commit message (Collapse) | Author |
|---|
|
Flush the chipset write buffers before and after adjusting the GTT base
register, just in case. We only modify this value upon initialisation
(boot and resume) so there should be no outstanding writes, however
there are always those persistent PGTBL_ER that keep getting reported
upon resume.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
On i830 if the tail pointer is set to within 2 cachelines of the end of
the buffer, the chip may hang. So instead if the tail were to land in
that location, we pad the end of the buffer with NOPs, and start again
at the beginning.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
There should be no difference, but we can eliminate redundant code.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
In some configuration, the PCU may allow us to overclock the GPU.
Check for this case and adjust the max frequency as appropriate. Also
initialize the min/max frequencies to default values as indicated by
hardware.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
... and just any combination of bits & ~PFIT_ENABLE. This way we do not
attempt disable to the panel fitter controller uselessly upon
intel_lvds_disable().
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
By tracking the current status of the backlight we can prevent recording
the value of the current backlight when we have disabled it. And so
prevent restoring it to 'off' after an unbalanced sequence of
intel_lvds_disable/enable.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=22672
Tested-by: Alex Riesen <raa.lkml@gmail.com>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
|
|
Alex Fiestas reported an issue with his HDMI connector being misdetected
as DVI unless he had something connected upon boot. By moving the
decision as to whether to use HDMI or DVI encoding for the HDMI capable
output until we probe the monitor means that we should avoid sending a
HDMI signal to a DVI monitor and also correctly detect hardware like
Alex's.
However, to really determine what connector is soldered onto the wire we
need to inspect the VBT sdvo child devices - but can we trust it?
Reported-by: Alex Fiestas <alex@eyeos.org>
Tested-by: Alex Fiestas <alex@eyeos.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=32828
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
|
|
Some voltage swing/pre-emphasis level use the same value on eDP
Sandybridge, like 400mv_0db and 600mv_0db are with the same value
of (0x0 << 22). So, fix them, and point out the value if it isn't
a supported voltage swing/pre-emphasis level.
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
|
|
Since Linux 2.6.36 the digital output on my system (855GME + DVI-I) is
not working any longer. The analog output is always activated
regardless of the type of monitor attached.
The culprit seems to be intel_crt_detect_ddc(), which returns true as
soon as an ACK from the EDID device is received. Obviously this
approach does not work with DVI-I where the analog and digital outputs
share a common DDC bus.
In a similar manner to the shared DDC wire, ala the "Mac Mini Hack", we
need an additional check to make sure that there really is an analog
device attached to the DDC.
Signed-off-by: David Müller <d.mueller@elsoft.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
|
|
When trying to do channel equalization, we need to make sure we still
have clock recovery on all lanes while training. We also need to try
clock recovery again if we lose the clock or if channel eq fails 5
times. We'll try clock recovery up to 5 more times before giving up
entirely.
Gets suspend/resume working on my Vaio again and brings us back into
compliance with the DP training sequence spec.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
We were using a stale pointer in the check which caused us to use CPU
attached DP params when we should have been using PCH attached params.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=31988
Tested-by: Jan-Hendrik Zab <jan@jhz.name>
Tested-by: Christoph Lukas <christoph.lukas@gmx.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (390 commits)
drm/radeon/kms: disable underscan by default
drm/radeon/kms: only enable hdmi features if the monitor supports audio
drm: Restore the old_fb upon modeset failure
drm/nouveau: fix hwmon device binding
radeon: consolidate asic-specific function decls for pre-r600
vga_switcheroo: comparing too few characters in strncmp()
drm/radeon/kms: add NI pci ids
drm/radeon/kms: don't enable pcie gen2 on NI yet
drm/radeon/kms: add radeon_asic struct for NI asics
drm/radeon/kms/ni: load default sclk/mclk/vddc at pm init
drm/radeon/kms: add ucode loader for NI
drm/radeon/kms: add support for DCE5 display LUTs
drm/radeon/kms: add ni_reg.h
drm/radeon/kms: add bo blit support for NI
drm/radeon/kms: always use writeback/events for fences on NI
drm/radeon/kms: adjust default clock/vddc tracking for pm on DCE5
drm/radeon/kms: add backend map workaround for barts
drm/radeon/kms: fill gpu init for NI asics
drm/radeon/kms: add disabled vbios accessor for NI asics
drm/radeon/kms: handle NI thermal controller
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
i2c: Constify i2c_client where possible
i2c-algo-bit: Complain about masters which can't read SCL
i2c-algo-bit: Refactor adapter registration
i2c: Add generic I2C multiplexer using GPIO API
i2c-nforce2: Remove unnecessary cast of pci_get_drvdata
i2c-i801: Include <linux/slab.h>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin: (52 commits)
Blackfin: encode cpu-rev into uImage name
Blackfin: bf54x: don't ack GPIO ints when unmasking them
Blackfin: sram_free_with_lsl: do not ignore return value of sram_free
Blackfin: boards: add missing "static" to peripheral lists
Blackfin: DNP5370: new board port
Blackfin: bf518f-ezbrd: fix dsa resources
Blackfin: move "-m elf32bfin" to general LDFLAGS
Blackfin: kgdb_test: make sure to initialize num2
Blackfin: kgdb: disable preempt schedule when running single step in kgdb
Blackfin: kgdb: disable interrupt when single stepping in ADEOS
Blackfin: SMP: kgdb: apply anomaly 257 work around
Blackfin: fix building IPIPE code when XIP is enabled
Blackfin: SMP: kgdb: flush core internal write buffer before flushinv
Blackfin: sport_uart resources: remove unused secondary RX/TX pins
Blackfin: tll6527m: fix spelling in unused code (struct name)
Blackfin: bf527-ezkit: add adau1373 chip address
Blackfin: no-mpu: fix masking of small uncached dma region
Blackfin: pm: drop irq save/restore in standby and suspend to mem callback
MAINTAINERS: update Analog Devices support info
Blackfin: dpmc.h: pull in new pll.h
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6
* 'driver-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
driver core: Document that device_rename() is only for networking
sysfs: remove useless test from sysfs_merge_group
driver-core: merge private parts of class and bus
driver core: fix whitespace in class_attr_string
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6
* 'staging-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6: (510 commits)
staging: speakup: fix failure handling
staging: usbip: remove double giveback of URB
Staging: batman-adv: Remove batman-adv from staging
Staging: hv: Use only one txf buffer per channel and kmalloc/GFP_KERNEL on initialize
staging: hv: remove unneeded osd_schedule_callback
staging: hv: convert channel_mgmt.c to not call osd_schedule_callback
staging: hv: convert vmbus_on_msg_dpc to not call osd_schedule_callback
staging: brcm80211: Fix WL_<type> logging macros
Staging: IIO: DDS: AD9833 / AD9834 driver
Staging: IIO: dds.h convenience macros
Staging: IIO: Direct digital synthesis abi documentation
staging: brcm80211: Convert ETHER_TYPE_802_1X to ETH_P_PAE
staging: brcm80211: Remove unused ETHER_TYPE_<foo> #defines
staging: brcm80211: Remove ETHER_HDR_LEN, use ETH_HLEN
staging: brcm80211: Convert ETHER_ADDR_LEN to ETH_ALEN
staging: brcm80211: Convert ETHER_IS<FOO> to is_<foo>_ether_addr
staging: brcm80211: Remove unused ether_<foo> #defines and struct
staging: brcm80211: Convert ETHER_IS_MULTI to is_multicast_ether_addr
staging: brcm80211: Remove unused #defines ETHER_<foo>_LOCALADDR
Staging: comedi: Fix checkpatch.pl issues in file s526.c
...
Fix up trivial conflict in drivers/video/udlfb.c
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86: (36 commits)
sony-laptop: support new hotkeys on the P, Z and EC series
platform/x86: Consistently select LEDS Kconfig options
sony-laptop: fix sparse non-ANSI function warning
intel_ips: fix sparse non-ANSI function warning
Support KHLB2 in the compal laptop driver
acer-wmi: Enabled Acer Launch Manager mode
[PATCH] intel_pmic_gpio: modify EOI handling following change of kernel irq subsystem
ACPI Thinkpad: We must always call va_end() after va_start() but do not do so in thinkpad_acpi.c::acpi_evalf()
acer-wmi: Initialize wlan/bluetooth/wwan rfkill software block state
acer-wmi: Detect the WiFi/Bluetooth/3G devices available
acer-wmi: Add 3G rfkill sysfs file
acer-wmi: Add acer wmi hotkey events support
platform/x86: Kconfig: Replace select by depends on ACPI_WMI
ideapad: pass ideapad_priv as argument (part 2)
ideapad: pass ideapad_priv as argument (part 1)
ideapad: add markups, unify comments and return result when init
ideapad: add hotkey support
ideapad: let camera power control entry under platform driver
ideapad: add platform driver for ideapad
fujitsu-laptop: fix compiler warning on pnp_ids
...
|
|
Helper functions for I2C and SMBus transactions don't modify the
i2c_client that is passed to them, so it can be marked const.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
The I2C specification explicitly describes both SDA and SCL as
bidirectional lines. An I2C master with a read-only SCL is thus not
compliant. If a slow slave stretches the clock, errors will happen,
so the bus can't be considered as reliable.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Use a function pointer to decide whether to call i2c_add_adapter or
i2c_add_numbered_adapter. This makes the code more compact than the
current strategy of having the common code in a separate function.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Add an i2c mux driver providing access to i2c bus segments using a
hardware MUX sitting on a master bus and controlled through gpio pins.
E.G. something like:
---------- ---------- Bus segment 1 - - - - -
| | SCL/SDA | |-------------- | |
| |------------| |
| | | | Bus segment 2 | |
| Linux | GPIO 1..N | MUX |--------------- Devices
| |------------| | | |
| | | | Bus segment M
| | | |---------------| |
---------- ---------- - - - - -
SCL/SDA of the master I2C bus is multiplexed to bus segment 1..M
according to the settings of the GPIO pins 1..N.
Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Commit 5a0e3ad6af8660be21ca98a971cd00f331318c05 added direct inclusion
of <linux/slab.h> to those source files that appeared to need it, but
somehow missed this. On most architectures <linux/slab.h> is still
indirectly included, but there are exceptions such as alpha.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
fix the failure handling in kobjects and the main function so that we
release the virtual keyboard if we exit due to another failure.
Signed-off-by: William Hubbs <w.d.hubbs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
In the vhci_urb_dequeue() function the TCP connection is checked twice.
Each time when the TCP connection is closed the URB is unlinked and given
back. Remove the second attempt of unlinking and giving back of the URB completely.
This patch fixes the bug described at https://bugzilla.kernel.org/show_bug.cgi?id=24872 .
Signed-off-by: Márton Németh <nm127@freemail.hu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6: (30 commits)
MAINTAINERS: Add tomoyo-dev-en ML.
SELinux: define permissions for DCB netlink messages
encrypted-keys: style and other cleanup
encrypted-keys: verify datablob size before converting to binary
trusted-keys: kzalloc and other cleanup
trusted-keys: additional TSS return code and other error handling
syslog: check cap_syslog when dmesg_restrict
Smack: Transmute labels on specified directories
selinux: cache sidtab_context_to_sid results
SELinux: do not compute transition labels on mountpoint labeled filesystems
This patch adds a new security attribute to Smack called SMACK64EXEC. It defines label that is used while task is running.
SELinux: merge policydb_index_classes and policydb_index_others
selinux: convert part of the sym_val_to_name array to use flex_array
selinux: convert type_val_to_struct to flex_array
flex_array: fix flex_array_put_ptr macro to be valid C
SELinux: do not set automatic i_ino in selinuxfs
selinux: rework security_netlbl_secattr_to_sid
SELinux: standardize return code handling in selinuxfs.c
SELinux: standardize return code handling in selinuxfs.c
SELinux: standardize return code handling in policydb.c
...
|
|
Add new mappings for assist, VAIO, zoom and eject buttons present on
refurbished P, Z and EC models.
Reported-by: Gyorgy Jeney <nog.lkml@gmail.com>
Reported-by: Stephan Mueller <smueller@chronox.de>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Mattia Dongili <malattia@linux.it>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging: (44 commits)
hwmon: Support for Dallas Semiconductor DS620
hwmon: driver for Sensirion SHT21 humidity and temperature sensor
hwmon: Add humidity attribute to sysfs ABI
hwmon: sysfs ABI updates
hwmon: (via-cputemp) sync hotplug handling with coretemp/pkgtemp
hwmon: (lm95241) Rewrite to avoid using macros
hwmon: (applesmc) Fix checkpatch errors and fix value range checks
hwmon: (applesmc) Update copyright information
hwmon: (applesmc) Silence driver
hwmon: (applesmc) Simplify feature sysfs handling
hwmon: (applesmc) Dynamic creation of fan files
hwmon: (applesmc) Extract all features generically
hwmon: (applesmc) Handle new temperature format
hwmon: (applesmc) Dynamic creation of temperature files
hwmon: (applesmc) Introduce a register lookup table
hwmon: (applesmc) Use pr_fmt and pr_<level>
hwmon: (applesmc) Relax the severity of device init failure
hwmon: (applesmc) Add MacBookAir3,1(3,2) support
hwmon: (w83627hf) Use pr_fmt and pr_<level>
hwmon: (w83627ehf) Use pr_fmt and pr_<level>
...
|
|
* 'next-devicetree' of git://git.secretlab.ca/git/linux-2.6: (29 commits)
of/flattree: forward declare struct device_node in of_fdt.h
ipmi: explicitly include of_address.h and of_irq.h
sparc: explicitly cast negative phandle checks to s32
powerpc/405: Fix missing #{address,size}-cells in i2c node
powerpc/5200: dts: refactor dts files
powerpc/5200: dts: Change combatible strings on localbus
powerpc/5200: dts: remove unused properties
powerpc/5200: dts: rename nodes to prepare for refactoring dts files
of/flattree: Update dtc to current mainline.
of/device: Don't register disabled devices
powerpc/dts: fix syntax bugs in bluestone.dts
of: Fixes for OF probing on little endian systems
of: make drivers depend on CONFIG_OF instead of CONFIG_PPC_OF
of/flattree: Add of_flat_dt_match() helper function
of_serial: explicitly include of_irq.h
of/flattree: Refactor unflatten_device_tree and add fdt_unflatten_tree
of/flattree: Reorder unflatten_dt_node
of/flattree: Refactor unflatten_dt_node
of/flattree: Add non-boottime device tree functions
of/flattree: Add Kconfig for EARLY_FLATTREE
...
Fix up trivial conflict in arch/sparc/prom/tree_32.c as per Grant.
|
|
Currently the x86 platform devices are not consistent about selecting
or depending on the LEDs Kconfig variables, and this inconsistency
leads to Kconfig getting upset and refusing to offer LEDs (even on
non-x86 platforms):
drivers/platform/x86/Kconfig:422:error: recursive dependency detected!
drivers/platform/x86/Kconfig:422: symbol EEEPC_WMI depends on ACPI_WMI
drivers/platform/x86/Kconfig:438: symbol ACPI_WMI is selected by ACER_WMI
drivers/platform/x86/Kconfig:18: symbol ACER_WMI depends on LEDS_CLASS
drivers/leds/Kconfig:10: symbol LEDS_CLASS is selected by EEEPC_WMI
Fix this by always selecting rather than depending on the symbols as
slightly more drivers use this approach already and it seems more
user friendly.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
|
|
Fix sparse warning for non-ANSI function declaration:
drivers/platform/x86/sony-laptop.c:1134:35: warning: non-ANSI function declaration of function 'sony_nc_rfkill_update'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Mattia Dongili <malattia@linux.it>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
|
|
Fix sparse warning for non-ANSI function declaration:
drivers/platform/x86/intel_ips.c:1477:25: warning: non-ANSI function declaration of function 'ips_link_to_i915_driver'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
|
|
Remove kobject.h from files which don't need it, notably,
sched.h and fs.h.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
* 'stable/bug-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/event: validate irq before get evtchn by irq
xen/fb: fix potential memory leak
xen/fb: fix xenfb suspend/resume race.
xen: disable ACPI NUMA for PV guests
xen/irq: Cleanup the find_unbound_irq
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
pata_platform: Remove CONFIG_HAVE_PATA_PLATFORM's dependencies.
pata_hpt37x: actually limit HPT370 to UltraDMA/66
pata_hpt3x2n: coding style cleanup
pata_hpt37x: coding style cleanup
pata_hpt366: coding style cleanup
pata_hpt3x2n: calculate average f_CNT
pata_hpt3x2n: clarify about HPT371N support
pata_hpt{37x|3x2n}: SATA mode filtering
[libata] avoid needlessly passing around ptr to SCSI completion func
[libata] new driver acard_ahci, for ATP8620 host controller
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (34 commits)
HID: roccat: Update sysfs attribute doc
HID: roccat: don't use #pragma pack
HID: roccat: Add support for Roccat Kone[+] v2
HID: roccat: reduce number of functions in kone and pyra drivers
HID: roccat: declare meaning of pack pragma usage in driver headers
HID: roccat: use class for char device for sysfs attribute creation
sysfs: Introducing binary attributes for struct class
HID: hidraw: add compatibility ioctl() for 32-bit applications.
HID: hid-picolcd: Fix memory leak in picolcd_debug_out_report()
HID: picolcd: fix misuse of logical operation in place of bitop
HID: usbhid: base runtime PM on modern API
HID: replace offsets values with their corresponding BTN_* defines
HID: hid-mosart: support suspend/resume
HID: hid-mosart: ignore buttons report
HID: hid-picolcd: don't use flush_scheduled_work()
HID: simplify an index check in hid_lookup_collection
HID: Hoist assigns from ifs
HID: Remove superfluous __inline__
HID: Use vzalloc for vmalloc/memset(,0...)
HID: Add and use hid_<level>: dev_<level> equivalents
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
spi / PM: Support dev_pm_ops
PM: Prototype the pm_generic_ operations
PM / Runtime: Generic resume shouldn't set RPM_ACTIVE unconditionally
PM: Use dev_name() in core device suspend and resume routines
PM: Permit registration of parentless devices during system suspend
PM: Replace the device power.status field with a bit field
PM: Remove redundant checks from core device resume routines
PM: Use a different list of devices for each stage of device suspend
PM: Avoid compiler warning in pm_noirq_op()
PM: Use pm_wakeup_pending() in __device_suspend()
PM / Wakeup: Replace pm_check_wakeup_events() with pm_wakeup_pending()
PM: Prevent dpm_prepare() from returning errors unnecessarily
PM: Fix references to basic-pm-debugging.txt in drivers-testing.txt
PM / Runtime: Add synchronous runtime interface for interrupt handlers (v3)
PM / Hibernate: When failed, in_suspend should be reset
PM / Hibernate: hibernation_ops->leave should be checked too
Freezer: Fix a race during freezing of TASK_STOPPED tasks
PM: Use proper ccflag flag in kernel/power/Makefile
PM / Runtime: Fix comments to match runtime callback code
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
firewire: use split transaction timeout only for split transactions
firewire: ohci: consolidate context status flags
firewire: ohci: cache the context run bit
firewire: ohci: flush AT contexts after bus reset - addendum
firewire: ohci: flush AT contexts after bus reset for OHCI 1.2
firewire: net: set carrier state at ifup
firewire: net: add carrier detection
firewire: net: ratelimit error messages
firewire: ohci: restart iso DMA contexts on resume from low power mode
firewire: ohci: restore GUID on resume.
firewire: ohci: use common buffer for self IDs and AR descriptors
firewire: ohci: optimize iso context checks in the interrupt handler
firewire: make PHY packet header format consistent
firewire: ohci: properly clear posted write errors
firewire: ohci: flush MMIO writes in the interrupt handler
firewire: ohci: fix AT context initialization error handling
firewire: ohci: Asynchronous Reception rewrite
firewire: core: Update WARN uses
firewire: nosy: char device is not seekable
|
|
When retrieving the event channel number from irq, the irq
number may not be valid under some conditions.
So far that can be when we suspend/resume and irq ends with -1.
Validate and return sanitized irq and provide diagnostics information.
[v3: added unlikely on the WARN path]
[v2: reworded the commit message]
Signed-off-by: Joe Jin <joe.jin@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Tested-by: Gurudas Pai <gurudas.pai@oracle.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
|
|
This patch fixes a potential memory leak when xenfb connect to
the backend fails.
Thanks for Ian's review and comments.
[v2: reworded the commit message a bit]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Joe Jin <joe.jin@oracle.com>
Tested-by: Gurudas Pai <gurudas.pai@oracle.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
|
|
When migrating guests over a long period we hit this:
<1>BUG: unable to handle kernel paging request at 0000000b819fdb98
<1>IP: [<ffffffff812a588f>] notify_remote_via_irq+0x13/0x34
<4>PGD 94b10067 PUD 0
<0>Oops: 0000 [#1] SMP
.. snip..
Call Trace:
[<ffffffff812712c9>] xenfb_send_event+0x5c/0x5e
[<ffffffff8100ea5f>] ? xen_restore_fl_direct_end+0x0/0x1
[<ffffffff81438d80>] ? _spin_unlock_irqrestore+0x16/0x18
[<ffffffff812714ee>] xenfb_refresh+0x1b1/0x1d7
[<ffffffff81270568>] ? sys_imageblit+0x1ac/0x458
[<ffffffff81271786>] xenfb_imageblit+0x2f/0x34
[<ffffffff8126a3e5>] soft_cursor+0x1b5/0x1c8
[<ffffffff8126a137>] bit_cursor+0x4b6/0x4d7
[<ffffffff8100ea5f>] ? xen_restore_fl_direct_end+0x0/0x1
[<ffffffff81438d80>] ? _spin_unlock_irqrestore+0x16/0x18
[<ffffffff81269c81>] ? bit_cursor+0x0/0x4d7
[<ffffffff812656b7>] fb_flashcursor+0xff/0x111
[<ffffffff812655b8>] ? fb_flashcursor+0x0/0x111
[<ffffffff81071812>] worker_thread+0x14d/0x1ed
[<ffffffff81075a8c>] ? autoremove_wake_function+0x0/0x3d
[<ffffffff81438d80>] ? _spin_unlock_irqrestore+0x16/0x18
[<ffffffff810716c5>] ? worker_thread+0x0/0x1ed
[<ffffffff810756e3>] kthread+0x6e/0x76
[<ffffffff81012dea>] child_rip+0xa/0x20
[<ffffffff81011fd1>] ? int_ret_from_sys_call+0x7/0x1b
[<ffffffff8101275d>] ? retint_restore_args+0x5/0x6
[<ffffffff81012de0>] ? child_rip+0x0/0x20
Code: 6b ff 0c 8b 87 a4 db 9f 81 66 85 c0 74 08 0f b7 f8 e8 3b ff ff ff c9
c3 55 48 89 e5 48 83 ec 10 0f 1f 44 00 00 89 ff 48 6b ff 0c <8b> 87 a4 db 9f
81 66 85 c0 74 14 48 8d 75 f0 0f b7 c0 bf 04 00
RIP [<ffffffff812a588f>] notify_remote_via_irq+0x13/0x34
RSP <ffff8800e7bf7bd0>
CR2: 0000000b819fdb98
---[ end trace 098b4b74827595d0 ]---
The root cause of the panic is the race between the resume and reconnect to the backend.
Clearing the 'update_wanted' flag of xenfb before disconnecting from the
backend fixes this issue.
Signed-off-by: Joe Jin <joe.jin@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Tested-by: Gurudas Pai <gurudas.pai@oracle.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
|
|
Rather than maintain Kconfig entries where people have to enter raw
numbers and hardcode lists of addresses/pins in the driver itself,
push it all to platform resources. This lets us simplify the driver,
the Kconfig, and gives board porters greater flexibility.
In the process, we need to also start supporting the early platform
interface. Not a big deal, but it causes the patch to be bigger than
a simple resource relocation.
All the Blackfin boards already have their resources updated and in
place for this change.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Now that the common header is sane, we can drop the transitional cruft.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
We're in the process of cleaning up the global Blackfin namespace, so the
bfin_sir driver needs to pull in the serial header explicitly now.
This does add a little transitional cruft to keep things compiling, but a
follow up patch in this series will cull that.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Lots of HDMI TVs overscan the incoming image by default.
The underscan option was added as a way to compensate for
that by underscanning the image so that the edges would
not be cut off on an overscanning TV. However, the TV
provides no way of knowing whether it is overscanning or
not. If the user has disabled overscan on their TV or has a
TV that does not overscan, you will get black bars around the
edges of your screen. Prior to the patch we got complaints
and bug reports from users with overscanning TVs, now with
the patch, we get lots of complaints and bug reports from
users with non-overscanning TVs. There's no good default,
but on average there have been more users complaining about
it being on by default than off, so change it to off. This
will probably result in a new deluge of overscanning TV user
complaints. There's no winning.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
This avoids some issues in the current hdmi audio code for monitors
without audio.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
* 'drm-radeon-ni' of ../drm-radeon-next: (30 commits)
radeon: consolidate asic-specific function decls for pre-r600
drm/radeon/kms: add NI pci ids
drm/radeon/kms: don't enable pcie gen2 on NI yet
drm/radeon/kms: add radeon_asic struct for NI asics
drm/radeon/kms/ni: load default sclk/mclk/vddc at pm init
drm/radeon/kms: add ucode loader for NI
drm/radeon/kms: add support for DCE5 display LUTs
drm/radeon/kms: add ni_reg.h
drm/radeon/kms: add bo blit support for NI
drm/radeon/kms: always use writeback/events for fences on NI
drm/radeon/kms: adjust default clock/vddc tracking for pm on DCE5
drm/radeon/kms: add backend map workaround for barts
drm/radeon/kms: fill gpu init for NI asics
drm/radeon/kms: add disabled vbios accessor for NI asics
drm/radeon/kms: handle NI thermal controller
drm/radeon/kms: parse DCE5 encoder caps when setting up encoders
drm/radeon/kms: dvo dpms updates for DCE5
drm/radeon/kms: dac dpms updates for DCE5
drm/radeon/kms: DCE5 atom dig encoder updates
drm/radeon/kms: DCE5 atom transmitter control updates
...
|
|
... or else we may end up disabling the wrong framebuffer, leading to an
OOPS, e.g:
[ 6033.229012] kernel BUG at drivers/gpu/drm/i915/i915_gem.c:3271!
[ 6033.229012] invalid opcode: 0000 [#1] SMP
[ 6033.229012] last sysfs file:
/sys/devices/virtual/backlight/acpi_video0/uevent
[ 6033.229012] Modules linked in: sunrpc cpufreq_ondemand acpi_cpufreq
mperf snd_hda_codec_analog snd_hda_intel snd_hda_codec snd_hwdep snd_seq
snd_seq_device snd_pcm snd_timer thinkpad_acpi ppdev snd r852 sm_common
iTCO_wdt uvcvideo i2c_i801 iTCO_vendor_support microcode wmi nand
videodev nand_ids nand_ecc snd_page_alloc parport_pc parport mtd
soundcore joydev v4l1_compat pcspkr uinput ipv6 sdhci_pci sdhci mmc_core
yenta_socket i915 drm_kms_helper drm i2c_algo_bit i2c_core video output
[last unloaded: scsi_wait_scan]
[ 6033.229012]
[ 6033.229012] Pid: 4834, comm: Xorg Not tainted 2.6.37-rc8+ #25 7661BL5/7661BL5
[ 6033.229012] EIP: 0060:[<f86fda5e>] EFLAGS: 00013246 CPU: 0
[ 6033.229012] EIP is at i915_gem_object_unpin+0x23/0x76 [i915]
[ 6033.229012] EAX: f68a4000 EBX: f6831f00 ECX: 000600fa EDX: f68a8000
[ 6033.229012] ESI: f68a4014 EDI: f68a42b8 EBP: f2169c44 ESP: f2169c3c
[ 6033.229012] DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
[ 6033.229012] Process Xorg (pid: 4834, ti=f2168000 task=f21c8000 task.ti=f2168000)
[ 6033.229012] Stack:
[ 6033.229012] f3a84800 f68a4014 f2169c54 f87045d8 f3a84800 f872d9a8 f2169c68 f7fd8091
[ 6033.229012] f3b952a4 00000000 f68a414c f2169cf0 f7fd9377 00000000 00000000 f7fd98b0
[ 6033.229012] f7fd9f4e 0000000f f7f328a0 00000000 00000000 00000000 f2169ca4 f68a414c
[ 6033.229012] Call Trace:
[ 6033.229012] [<f87045d8>] ? intel_crtc_disable+0x36/0x41 [i915]
[ 6033.229012] [<f7fd8091>] ? drm_helper_disable_unused_functions+0xcd/0xf9 [drm_kms_helper]
[ 6033.229012] [<f7fd9377>] ? drm_crtc_helper_set_config+0x62a/0x7f7 [drm_kms_helper]
[ 6033.229012] [<c04daa10>] ? __slab_free+0x1b/0xa4
[ 6033.229012] [<f7fd7e62>] ? drm_fb_helper_initial_config+0x466/0x497 [drm_kms_helper]
[ 6033.229012] [<f7fd7ea3>] ? drm_fb_helper_restore+0x10/0x2a [drm_kms_helper]
[ 6033.229012] [<f86f2577>] ? i915_driver_lastclose+0x2a/0x57 [i915]
[ 6033.229012] [<f7f1989f>] ? drm_lastclose+0x45/0x23e [drm]
[ 6033.229012] [<f7f1a0b4>] ? drm_release+0x462/0x4d7 [drm]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
drm-core-next
* 'nouveau/drm-nouveau-next' of ../drm-nouveau-next:
drm/nouveau: fix hwmon device binding
drm/nouveau: create grctx on the fly on all chipsets
drm/nvc0: fix init without firmware present
drm/nvc0/pgraph: fix 0x406028/0x405870 init
drm/nvc0/pgraph: more unit names
drm/nvc0/pfifo: support for chipsets with only one PSUBFIFO (0xc1)
drm/nvc0: reserve only subc 0 for kernel use
drm/nv50: sync up gr data error names with rnn, use for nvc0 also
drm/nvc0: parse a couple more PGRAPH_INTR
drm/nvc0: nuke left-over debug messages
drm/nvc0: kill off a couple more magics
drm/nouveau: Validate channel indices passed from userspace.
drm/nouveau: Only select ACPI_VIDEO if its dependencies are met
|
|
Conflicts:
security/smack/smack_lsm.c
Verified and added fix by Stephen Rothwell <sfr@canb.auug.org.au>
Ok'd by Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: James Morris <jmorris@namei.org>
|
