| Age | Commit message (Collapse) | Author |
|---|
|
commit b251412db99ccd4495ce372fec7daee27bf06923 upstream.
Intermittently, b43 will report "Out of order TX status report on DMA ring".
When this happens, the driver must be reset before communication can resume.
The cause of the problem is believed to be an error in the closed-source
firmware; however, all versions of the firmware are affected.
This change uses the observation that the expected status is always 2 less
than the observed value, and supplies a fake status report to skip one
header/data pair.
Not all devices suffer from this problem, but it can occur several times
per second under heavy load. As each occurence kills the unmodified driver,
this patch makes if possible for the affected devices to function. The patch
logs only the first instance of the reset operation to prevent spamming
the logs.
Tested-by: Chris Vine <chris@cvine.freeserve.co.uk>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e67dd874e60529dbd2e8232babb1e23479ba2ffa upstream.
We're using "mind" variable to find the VCM that got the best polling
results. For each VCM we calculte "currd" which is compared to the
"mind". For PHY rev3+ "currd" gets values around 14k-40k. Looking for a
value smaller than 40 makes no sense, so increase the initial value.
This fixes a regression introduced in 3.4 by commit:
e0c9a0219a8f542e3946fe972a68aacf8c3f906c
(my BCM4322 performance dropped from 18,4Mb/s to 9,26Mb/s)
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 36ef0b473fbf43d5db23eea4616cc1d18cec245f upstream.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3d464d9b71ef2f2b40a4bc9dcf06794fd1be9d12 upstream.
This device needs to be added to the quirks list with HID_QUIRK_NO_INIT_REPORTS,
otherwise it causes 10 seconds timeout during report initialization.
This fixes Red Hat bugzilla https://bugzilla.redhat.com/show_bug.cgi?id=806587
Signed-off-by: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 74632d11a133b5baf6b9d622dd19d2f944d93d94 upstream.
The commit 'ath9k_hw: fix calibration issues on chainmask that don't
include chain 0' changed the hardware chainmask to the chip chainmask
for the duration of the calibration, but the revert to user
configuration in the reset path runs too early.
That causes some issues with limiting the number of antennas (including
spurious failure in hardware-generated packets).
Fix this by reverting the chainmask after the essential parts of the
calibration that need the workaround, and before NF calibration is run.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Tested-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f901b6bc404b67d96eca739857c097e022727b71 upstream.
Thias patch fixes a define conflict between the SH architecture and the sja1000
driver:
drivers/net/can/sja1000/sja1000.h:59:0: warning:
"REG_SR" redefined [enabled by default]
arch/sh/include/asm/ptrace_32.h:25:0: note:
this is the location of the previous definition
A SJA1000_ prefix is added to the offending sja1000 define only, to make a
minimal patch suited for stable. A later patch will add a SJA1000_ prefix to
all defines in sja1000.h.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e4317ce877a31dbb9d96375391c1c4ad2210d637 upstream.
For the s626 driver, there is a bug in the handling of asynchronous
commands on the AI subdevice when the stop source is `TRIG_NONE`. The
command should run continuously until cancelled, but the interrupt
handler stops the command running after the first scan.
The command set-up function `s626_ai_cmd()` contains this code:
switch (cmd->stop_src) {
case TRIG_COUNT:
/* data arrives as one packet */
devpriv->ai_sample_count = cmd->stop_arg;
devpriv->ai_continous = 0;
break;
case TRIG_NONE:
/* continous acquisition */
devpriv->ai_continous = 1;
devpriv->ai_sample_count = 0;
break;
}
The interrupt handler `s626_irq_handler()` contains this code:
if (!(devpriv->ai_continous))
devpriv->ai_sample_count--;
if (devpriv->ai_sample_count <= 0) {
devpriv->ai_cmd_running = 0;
/* ... */
}
So `devpriv->ai_sample_count` is only decremented for the `TRIG_COUNT`
case, but `devpriv->ai_cmd_running` is set to 0 (and the command
stopped) regardless.
Fix this in `s626_ai_cmd()` by setting `devpriv->ai_sample_count = 1`
for the `TRIG_NONE` case. The interrupt handler will not decrement it
so it will remain greater than 0 and the check for stopping the
acquisition will fail.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ebaf5795ef57a70a042ea259448a465024e2821d upstream.
Add support for the AR9462 chip
T: Bus=03 Lev=01 Prnt=01 Port=08 Cnt=01 Dev#= 5 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0cf3 ProdID=817a Rev= 0.02
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Cc: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d66629c1325399cf080ba8b2fb086c10e5439cdd upstream.
Add support for the AR9462 chip
T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0cf3 ProdID=0036 Rev= 0.02
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
A: FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Cc: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cb7da022450cdaaebd33078b6b32fb7dd2aaf6db upstream.
Since commit 8871e99f89b7 ('asus-laptop: HRWS/HWRS typo'), module
initialisation is very slow on the Asus UL30A. The HWRS method takes
about 12 seconds to run, and subsequent initialisation also seems to
be delayed. Since we don't really need the result, don't bother
calling it on init. Those who are curious can still get the result
through the 'infos' device attribute.
Update the comment about HWRS in show_infos().
Reported-by: ryan <draziw+deb@gmail.com>
References: http://bugs.debian.org/692436
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6ef9e2f6d12ce9e2120916804d2ddd46b954a70b upstream.
If CONFIG_MAC80211_MESH is not set, cfg80211 will now allow advertising
interface combinations with NL80211_IFTYPE_MESH_POINT present.
Add appropriate ifdefs to avoid running into errors.
[Backported for 3.8-stable. Removed code of simultaneous AP and mesh
mode added in 4a5fc6d 3.9-rc1.]
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Lingzhu Xiang <lxiang@redhat.com>
Reviewed-by: CAI Qian <caiqian@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d627b62ff8d4d36761adbcd90ff143d79c94ab22 upstream.
This is rather a hack to fix brightness hotkeys on a Clevo laptop. CADL is not
used anywhere in the driver code at the moment, but it could be used in BIOS as
is the case with the Clevo laptop.
The Clevo B7130 requires the CADL field to contain at least the ID of
the LCD device. If this field is empty, the ACPI methods that are called
on pressing brightness / display switching hotkeys will not trigger a
notification. As a result, it appears as no hotkey has been pressed.
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=45452
Tested-by: Peter Wu <lekensteyn@gmail.com>
Signed-off-by: Peter Wu <lekensteyn@gmail.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5492bf3d5655b4954164f69c02955a7fca267611 upstream.
Add missing get_icount field to two-port driver.
The two-port driver was not updated when switching to the new icount
interface in commit 0bca1b913aff ("tty: Convert the USB drivers to the
new icount interface").
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 618aa1068df29c37a58045fe940f9106664153fd upstream.
Remove bogus disconnect test introduced by 95bef012e ("USB: more serial
drivers writing after disconnect") which prevented queued data from
being freed on disconnect.
The possible IO it was supposed to prevent is long gone.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d7971051e4df825e0bc11b995e87bfe86355b8e5 upstream.
Make sure the interface is not released before our serial device.
Note that drivers are still not allowed to access the interface in
any way that may interfere with another driver that may have gotten
bound to the same interface after disconnect returns.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cb25505fc604292c70fc02143fc102f54c8595f0 upstream.
Unregister tty device in disconnect as is required by the USB stack.
By deferring unregistration to when the last tty reference is dropped,
the parent interface device can get unregistered before the child
resulting in broken hotplug events being generated when the tty is
finally closed:
KERNEL[2290.798128] remove /devices/pci0000:00/0000:00:1d.7/usb2/2-1/2-1:3.1 (usb)
KERNEL[2290.804589] remove /devices/pci0000:00/0000:00:1d.7/usb2/2-1 (usb)
KERNEL[2294.554799] remove /2-1:3.1/tty/ttyACM0 (tty)
The driver must deal with tty callbacks after disconnect by checking the
disconnected flag. Specifically, further opens must be prevented and
this is already implemented.
Acked-by: Oliver Neukum <oneukum@suse.de>
Cc: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 00eed9c814cb8f281be6f0f5d8f45025dc0a97eb upstream.
xhci has its own interrupt enabling routine, which will try to
use MSI-X/MSI if present. So the usb core shouldn't try to enable
legacy interrupts; on some machines the xhci legacy IRQ setting
is invalid.
v3: Be careful to not break XHCI_BROKEN_MSI workaround (by trenn)
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Oliver Neukum <oneukum@suse.de>
Cc: Thomas Renninger <trenn@suse.de>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Frederik Himpe <fhimpe@vub.ac.be>
Cc: David Haerdeman <david@hardeman.nu>
Cc: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reviewed-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f8264340e694604863255cc0276491d17c402390 upstream.
According to XHCI specification (5.5.2.1) the IP is bit 0 and IE is bit 1
of IMAN register. Previously their definitions were reversed.
Even though there are no ill effects being observed from the swapped
definitions (because IMAN_IP is RW1C and in legacy PCI case we come in
with it already set to 1 so it was clearing itself even though we were
setting IMAN_IE instead of IMAN_IP), we should still correct the values.
This patch should be backported to kernels as old as 2.6.36, that
contain the commit 4e833c0b87a30798e67f06120cecebef6ee9644c "xhci: don't
re-enable IE constantly".
Signed-off-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1ee9e2aa7b31427303466776f455d43e5e3c9275 upstream.
Commit f0dc117abdfa ("IPoIB: Fix TX queue lockup with mixed UD/CM
traffic") attempts to solve an issue where unprocessed UD send
completions can deadlock the netdev.
The patch doesn't fully resolve the issue because if more than half
the tx_outstanding's were UD and all of the destinations are RC
reachable, arming the CQ doesn't solve the issue.
This patch uses the IB_CQ_REPORT_MISSED_EVENTS on the
ib_req_notify_cq(). If the rc is above 0, the UD send cq completion
callback is called directly to re-arm the send completion timer.
This issue is seen in very large parallel filesystem deployments
and the patch has been shown to correct the issue.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 29f86e66428ee083aec106cca1748dc63d98ce23 upstream.
Device stucks on filesystem writes, unless following quirk is passed:
echo 04e8:5136:m > /sys/module/usb_storage/parameters/quirks
Add corresponding entry to unusual_devs.h
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fa8d387dc3f62062a6b4afbbb2a3438094fd8584 upstream.
Fixes a segfault on asics without a blit callback.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=62239
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e4d170633fde379f39a90f8a5e7eb619b5d1144d upstream.
Richland APUs are a new version of the Trinity APUs
with performance and power management improvements.
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7ac9ad11b2a5cf77a92b58ee6b672ad2fa155eb1 upstream.
See https://bugzilla.redhat.com/show_bug.cgi?id=916290
Used a temp var since we take its address in sg_init_one.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c19b3b0f6eed552952845e4ad908dba2113d67b4 upstream.
When KMS has parsed an EDID "detailed timing", it leaves the frame rate
zeroed. Consecutive (debug-) output of that mode thus yields 0 for
vsync. This simple fix also speeds up future invocations of
drm_mode_vrefresh().
While it is debatable whether this qualifies as a -stable fix I'd apply
it for consistency's sake; drm_helper_probe_single_connector_modes()
does the same thing already for all probed modes.
Signed-off-by: Torsten Duwe <duwe@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 16dad1d743d31a104a849c8944e6b9eb479f6cd7 upstream.
EDID spreads some values across multiple bytes; bit-fiddling is needed
to retrieve these. The current code to parse "detailed timings" has a
cut&paste error that results in a vsync offset of at most 15 lines
instead of 63.
See
http://en.wikipedia.org/wiki/EDID
and in the "EDID Detailed Timing Descriptor" see bytes 10+11 show why
that needs to be a left shift.
Signed-off-by: Torsten Duwe <duwe@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3118a4f652c7b12c752f3222af0447008f9b2368 upstream.
It is possible to wrap the counter used to allocate the buffer for
relocation copies. This could lead to heap writing overflows.
CVE-2013-0913
v3: collapse test, improve comment
v2: move check into validate_exec_list
Signed-off-by: Kees Cook <keescook@chromium.org>
Reported-by: Pinkie Pie
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5f0fabf84d7b52f979dcbafa3d3c530c60d9a92c upstream.
smatch found this error:
CHECK drivers/net/wireless/mwifiex/join.c
drivers/net/wireless/mwifiex/join.c:1121
mwifiex_cmd_802_11_ad_hoc_join()
error: testing array offset 'i' after use.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9437a248e7cac427c898bdb11bd1ac6844a1ead4 upstream.
The driver was failing to clear the BSSID when a disconnect happened. That
prevented a reconnection. This problem is reported at
https://bugzilla.redhat.com/show_bug.cgi?id=789605,
https://bugzilla.redhat.com/show_bug.cgi?id=866786,
https://bugzilla.redhat.com/show_bug.cgi?id=906734, and
https://bugzilla.kernel.org/show_bug.cgi?id=46171.
Thanks to Jussi Kivilinna for making the critical observation
that led to the solution.
Reported-by: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Tested-by: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Tested-by: Alessandro Lannocca <alessandro.lannocca@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 664899786cb49cb52f620e06ac19c0be524a7cfa upstream.
When run at debug 3 or higher, rtl8192cu reports a BUG as follows:
BUG: scheduling while atomic: kworker/u:0/5281/0x00000002
INFO: lockdep is turned off.
Modules linked in: rtl8192cu rtl8192c_common rtlwifi fuse af_packet bnep bluetooth b43 mac80211 cfg80211 ipv6 snd_hda_codec_conexant kvm_amd k
vm snd_hda_intel snd_hda_codec bcma rng_core snd_pcm ssb mmc_core snd_seq snd_timer snd_seq_device snd i2c_nforce2 sr_mod pcmcia forcedeth i2c_core soundcore
cdrom sg serio_raw k8temp hwmon joydev ac battery pcmcia_core snd_page_alloc video button wmi autofs4 ext4 mbcache jbd2 crc16 thermal processor scsi_dh_alua
scsi_dh_hp_sw scsi_dh_rdac scsi_dh_emc scsi_dh ata_generic pata_acpi pata_amd [last unloaded: rtlwifi]
Pid: 5281, comm: kworker/u:0 Tainted: G W 3.8.0-wl+ #119
Call Trace:
[<ffffffff814531e7>] __schedule_bug+0x62/0x70
[<ffffffff81459af0>] __schedule+0x730/0xa30
[<ffffffff81326e49>] ? usb_hcd_link_urb_to_ep+0x19/0xa0
[<ffffffff8145a0d4>] schedule+0x24/0x70
[<ffffffff814575ec>] schedule_timeout+0x18c/0x2f0
[<ffffffff81459ec0>] ? wait_for_common+0x40/0x180
[<ffffffff8133f461>] ? ehci_urb_enqueue+0xf1/0xee0
[<ffffffff810a579d>] ? trace_hardirqs_on+0xd/0x10
[<ffffffff81459f65>] wait_for_common+0xe5/0x180
[<ffffffff8107d1c0>] ? try_to_wake_up+0x2d0/0x2d0
[<ffffffff8145a08e>] wait_for_completion_timeout+0xe/0x10
[<ffffffff8132ab1c>] usb_start_wait_urb+0x8c/0x100
[<ffffffff8132adf9>] usb_control_msg+0xd9/0x130
[<ffffffffa057dd8d>] _usb_read_sync+0xcd/0x140 [rtlwifi]
[<ffffffffa057de0e>] _usb_read32_sync+0xe/0x10 [rtlwifi]
[<ffffffffa04b0555>] rtl92cu_update_hal_rate_table+0x1a5/0x1f0 [rtl8192cu]
The cause is a synchronous read from routine rtl92cu_update_hal_rate_table().
The resulting output is not critical, thus the debug statement is
deleted.
Reported-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2563a4524febe8f4a98e717e02436d1aaf672aa2 upstream.
Masks kernel address info-leak in object dumps with the %pK suffix,
so they cannot be used to target kernel memory corruption attacks if
the kptr_restrict sysctl is set.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit fae8563b25f73dc584a07bcda7a82750ff4f7672 ]
Using TX push when notifying the NIC of multiple new descriptors in
the ring will very occasionally cause the TX DMA engine to re-use an
old descriptor. This can result in a duplicated or partly duplicated
packet (new headers with old data), or an IOMMU page fault. This does
not happen when the pushed descriptor is the only one written.
TX push also provides little latency benefit when a packet requires
more than one descriptor.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 35205b211c8d17a8a0b5e8926cb7c73e9a7ef1ad ]
efx_device_detach_sync() locks all TX queues before marking the device
detached and thus disabling further TX scheduling. But it can still
be interrupted by TX completions which then result in TX scheduling in
soft interrupt context. This will deadlock when it tries to acquire
a TX queue lock that efx_device_detach_sync() already acquired.
To avoid deadlock, we must use netif_tx_{,un}lock_bh().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 29c69a4882641285a854d6d03ca5adbba68c0034 ]
We must only ever stop TX queues when they are full or the net device
is not 'ready' so far as the net core, and specifically the watchdog,
is concerned. Otherwise, the watchdog may fire *immediately* if no
packets have been added to the queue in the last 5 seconds.
The device is ready if all the following are true:
(a) It has a qdisc
(b) It is marked present
(c) It is running
(d) The link is reported up
(a) and (c) are normally true, and must not be changed by a driver.
(d) is under our control, but fake link changes may disturb userland.
This leaves (b). We already mark the device absent during reset
and self-test, but we need to do the same during MTU changes and ring
reallocation. We don't need to do this when the device is brought
down because then (c) is already false.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commits b590ace09d51cd39744e0f7662c5e4a0d1b5d952 and
c73e787a8db9117d59b5180baf83203a42ecadca ]
We assume that the mapping between DMA and virtual addresses is done
on whole pages, so we can find the page offset of an RX buffer using
the lower bits of the DMA address. However, swiotlb maps in units of
2K, breaking this assumption.
Add an explicit page_offset field to struct efx_rx_buffer.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 3a68f19d7afb80f548d016effbc6ed52643a8085 ]
We may currently allocate two RX DMA buffers to a page, and only unmap
the page when the second is completed. We do not sync the first RX
buffer to be completed; this can result in packet loss or corruption
if the last RX buffer completed in a NAPI poll is the first in a page
and is not DMA-coherent. (In the middle of a NAPI poll, we will
handle the following RX completion and unmap the page *before* looking
at the content of the first buffer.)
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
[bwh: Backported to 3.4: adjust context]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ef492f11efed9a6a1686bf914fb74468df59385c ]
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 450783747f42dfa3883920acfad4acdd93ce69af ]
MCDI supports requests up to 252 bytes long, which is only enough to
pass 63 RX queue IDs to MC_CMD_FLUSH_RX_QUEUES. However a VF may have
up to 64 RX queues, and if we try to flush them all we will generate
an over-length request and BUG() in efx_mcdi_copyin(). Currently
all VF drivers limit themselves to 32 RX queues, so reducing the
limit to 63 does no harm.
Also add a BUILD_BUG_ON in efx_mcdi_flush_rxqs() so we remember to
deal with the same problem there if EFX_MAX_CHANNELS is increased.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d4f2cecce138c34960c467d0ae38a6d4bcd6af7b ]
Currently VF queues and drivers may remain active during this test.
This could cause memory corruption or spurious test failures.
Therefore we reset the port/function before running these tests on
Siena.
On Falcon this doesn't work: we have to do some additional
initialisation before some blocks will work again. So refactor the
reset/register-test sequence into an efx_nic_type method so
efx_selftest() doesn't have to consider such quirks.
In the process, fix another minor bug: Siena does not have an
'invisible' reset and the self-test currently fails to push the PHY
configuration after resetting. Passing RESET_TYPE_ALL to
efx_reset_{down,up}() fixes this.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ebf98e797b4e26ad52ace1511a0b503ee60a6cd4 ]
efx_mcdi_poll() uses get_seconds() to read the current time and to
implement a polling timeout. The use of this function was chosen
partly because it could easily be replaced in a co-sim environment
with a macro that read the simulated time.
Unfortunately the real get_seconds() returns the system time (real
time) which is subject to adjustment by e.g. ntpd. If the system time
is adjusted forward during a polled MCDI operation, the effective
timeout can be shorter than the intended 10 seconds, resulting in a
spurious failure. It is also possible for a backward adjustment to
delay detection of a areal failure.
Use jiffies instead, and change MCDI_RPC_TIMEOUT to be denominated in
jiffies. Also correct rounding of the timeout: check time > finish
(or rather time_after(time, finish)) and not time >= finish.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c2f3b8e3a44b6fe9e36704e30157ebe1a88c08b1 ]
The assertion of netif_device_present() at the top of
efx_hard_start_xmit() may fail if we don't do this.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
[bwh: Backported to 3.4: adjust context]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 525d9e824018cd7cc8d8d44832ddcd363abfe6e1 ]
We sometimes hit a "failed to flush" timeout on some TX queues, but the
flushes have completed and the flush completion events seem to go missing.
In this case, we can check the TX_DESC_PTR_TBL register and drain the
queues if the flushes had finished.
[bwh: Minor fixes to coding style]
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d5e8cc6c946e0857826dcfbb3585068858445bfe ]
Receiving pause frames can block TX queue flushes. Earlier changes
work around this by reconfiguring the MAC during flushes for VFs, but
during flushes for the PF we would only change the fc_disable counter.
Unless the MAC is reconfigured for some other reason during the flush
(which I would not expect to happen) this had no effect at all.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 0a6e5008a9df678b48f8d4e57601aa4270df6c14 ]
The least significant bit number (LBN) of a field within an MCDI
structure is counted from the start of the structure, not the
containing dword. In MCDI_ARRAY_FIELD() we need to mask it rather
than using the usual EFX_DWORD_FIELD() macro.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 9724a8504c875145f5a513bb8eca50671cee23b4 ]
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit bfeed902946a31692e7a24ed355b6d13ac37d014 ]
On big-endian systems the MTD partition names currently have mangled
subtype numbers and are not recognised by the firmware update tool
(sfupdate).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 3dca9d2dc285faf1910d405b65df845cab061356 ]
efx_nic_fatal_interrupt() disables DMA before scheduling a reset.
After this, we need not and *cannot* flush queues.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b009aac12cd0fe34293c68af8ac48b85be3bd858 ]
The UPDATE_QSTAT function introduced on February 15, 2012
in commit 1355b704b9ba "bnx2x: consistent statistics after
internal driver reload" incorrectly fails to handle overflow
during addition of the lower 32-bit field of a stat.
This bug is present since 3.4-rc1 and should thus be considered
a candidate for stable 3.4+ releases.
Google-Bug-Id: 8374428
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Cc: Mintz Yuval <yuvalmin@broadcom.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 46aa92d1ba162b4b3d6b7102440e459d4e4ee255 ]
ubuf info allocator uses guest controlled head as an index,
so a malicious guest could put the same head entry in the ring twice,
and we will get two callbacks on the same value.
To fix use upend_idx which is guaranteed to be unique.
Reported-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Cc: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 7c6cdead7cc9a99650d15497aae47d7472217eb1 ]
Commit d13ba512cbba7de5d55d7a3b2aae7d83c8921457 ("tg3: Remove
SPEED_UNKNOWN checks") cleaned up the autoneg advertisement by
removing some dead code. One effect of this change was that the
advertisement register would not be updated if autoneg is turned off.
This exposed a bug on the 5715 device w.r.t linking. The 5715 defaults
to advertise only 10Mb Full duplex. But with autoneg disabled, it needs
the configured speed enabled in the advertisement register to link up.
This patch adds the work around to advertise all speeds on the 5715 when
autoneg is disabled.
Reported-by: Marcin Miotk <marcinmiotk81@gmail.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 876254ae2758d50dcb08c7bd00caf6a806571178 ]
bond_update_speed_duplex() might sleep while calling underlying slave's
routines. Move it out of atomic context in bond_enslave() and remove it
from bond_miimon_commit() - it was introduced by commit 546add79, however
when the slave interfaces go up/change state it's their responsibility to
fire NETDEV_UP/NETDEV_CHANGE events so that bonding can properly update
their speed.
I've tested it on all combinations of ifup/ifdown, autoneg/speed/duplex
changes, remote-controlled and local, on (not) MII-based cards. All changes
are visible.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
