| Age | Commit message (Collapse) | Author |
|---|
|
commit cd006086fa5d91414d8ff9ff2b78fbb593878e3c upstream.
When we are hosted on a Microsoft Hyper-V hypervisor the guest disks
are exposed both via the Hyper-V paravirtualised drivers and via an
emulated SATA disk drive. In this case we want to use the paravirtualised
drivers if we can as they are much more efficient. Note that the Hyper-V
paravirtualised drivers only expose the virtual hard disk devices, the
CDROM/DVD devices must still be enumerated.
Mark the host controller ATA_HOST_IGNORE_ATA to prevent enumeration of
disk devices.
BugLink: http://bugs.launchpad.net/bugs/929545
BugLink: http://bugs.launchpad.net/bugs/942316
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Cc: Victor Miasnikov <vvm@tut.by>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit db63a4c8115a0bb904496e1cdd3e7488e68b0d06 upstream.
Where devices are visible via more than one host we sometimes wish to
indicate that cirtain devices should be ignored on a specific host. Add a
host flag indicating that this host wishes to ignore ATA specific devices.
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Cc: Victor Miasnikov <vvm@tut.by>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3eef8918ff440837f6af791942d8dd07e1a268ee upstream.
By correctly describing the rinbuffers as being in the GTT domain, it
appears that we are more careful with the management of the CPU cache
upon resume and so prevent some coherency issue when submitting commands
to the GPU later. A secondary effect is that the debug logs are then
consistent with the actual usage (i.e. they no longer describe the
ringbuffers as being in the CPU write domain when we are accessing them
through an wc iomapping.)
Reported-and-tested-by: Daniel Gnoutcheff <daniel@gnoutcheff.name>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=41092
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d26098759cf6d32148649c165f87a7590bc25b89 upstream.
Fix regresson since the introduction of command stream checking on
evergreen (thread referenced below). Issue is cause by ddx allocating
bo with formula width*height*bpp while programming the GPU command
stream with ALIGN(height, 8). In some case (where page alignment does
not hide the extra size bo should be according to height alignment)
the kernel will reject the command stream.
This patch reprogram the command stream to slice - 1 (slice is
a derivative value from height) which avoid rejecting the command
stream while keeping the value of command stream checking from a
security point of view.
This patch also fix wrong computation of layer size for 2D tiled
surface. Which should fix issue when 2D color tiling is enabled.
This dump the radeon KMS_DRIVER_MINOR so userspace can know if
they are on a fixed kernel or not.
https://lkml.org/lkml/2012/6/3/80
https://bugs.freedesktop.org/show_bug.cgi?id=50892
https://bugs.freedesktop.org/show_bug.cgi?id=50857
!!! STABLE need a custom version of this patch for 3.4 !!!
v2: actually bump the minor version and add comment about stable
v3: do compute the height the ddx was trying to use
[airlied: drop left over debug]
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cfb46f433a4da97c31780e08a259fac2cb6bd61f upstream.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Acked-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 155689defc782b486a7e6776a57ecc4ebb37ed52 upstream.
We are not yet ready for this and it makes a mess on some devices.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f461f27a4436dbe691908fe08b867ef888848cc3 upstream.
Fix the issue of C_CAN interrupts getting disabled forever when canconfig
utility is used multiple times. According to NAPI usage we disable all
the hardware interrupts in ISR and re-enable them in poll(). Current
implementation calls napi_enable() after hardware interrupts are enabled.
If we get any interrupts between these two steps then we do not process
those interrupts because napi is not enabled. Mostly these interrupts
come because of STATUS is not 0x7 or ERROR interrupts. If napi_enable()
happens before HW interrupts enabled then c_can_poll() function will be
called eventual re-enabling.
This patch moves the napi_enable() call before interrupts enabled.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 148c87c89e1a8863d3d965179f3ab1a06490569e upstream.
This patch fixes an interrupt thrash issue with c_can driver.
In c_can_isr() function interrupts are disabled and enabled only in
c_can_poll() function. c_can_isr() & c_can_poll() both read the
irqstatus flag. However, irqstatus is always read as 0 in c_can_poll()
because all C_CAN interrupts are disabled in c_can_isr(). This causes
all interrupts to be re-enabled in c_can_poll() which in turn causes
another interrupt since the event is not really handled. This keeps
happening causing a flood of interrupts.
To fix this, read the irqstatus register in isr and use the same cached
value in the poll function.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 617caccebe451716df21c069b079d5936ed7b0f3 upstream.
This patch fixes an issue with transmit routine, which causes
"can_put_echo_skb: BUG! echo_skb is occupied!" message when
using "cansequence -p" on D_CAN controller.
In c_can driver, while transmitting packets tx_echo flag holds
the no of can frames put for transmission into the hardware.
As the comment above c_can_do_tx() indicates, if we find any packet
which is not transmitted then we should stop looking for more.
In the current implementation this is not taken care of causing the
said message.
Also, fix the condition used to find if the packet is transmitted
or not. Current code skips the first tx message object and ends up
checking one extra invalid object.
While at it, fix the comment on top of c_can_do_tx() to use the
terminology "packet" instead of "package" since it is more
standard.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dd03cff23d694cfb0fdae80cb618e7ced05ea696 upstream.
Adding device IDs for Aircard 320U and two other devices
found in the out-of-tree version of this driver.
Cc: linux@sierrawireless.com
Cc: Autif Khan <autif.mlist@gmail.com>
Cc: Tom Cassidy <tomas.cassidy@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e828b9fb4f6c3513950759d5fb902db5bd054048 upstream.
found in 2012_03_22_RT5572_Linux_STA_v2.6.0.0_DPO
RT3070:
(0x2019,0x5201) Planex Communications, Inc. RT8070
(0x7392,0x4085) 2L Central Europe BV 8070
7392 is Edimax
RT35xx:
(0x1690,0x0761) Askey
was Fujitsu Stylistic 550, but 1690 is Askey
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 63b376411173c343bbcb450f95539da91f079e0c upstream.
They were taken from ralink drivers:
2011_0719_RT3070_RT3370_RT5370_RT5372_Linux_STA_V2.5.0.3_DPO
2012_03_22_RT5572_Linux_STA_v2.6.0.0_DPO
0x1eda,0x2210 RT3070 Airties
0x083a,0xb511 RT3370 Panasonic
0x0471,0x20dd RT3370 Philips
0x1690,0x0764 RT35xx Askey
0x0df6,0x0065 RT35xx Sitecom
0x0df6,0x0066 RT35xx Sitecom
0x0df6,0x0068 RT35xx Sitecom
0x2001,0x3c1c RT5370 DLink
0x2001,0x3c1d RT5370 DLink
2001 is D-Link not Alpha
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e5851dac2c95af7159716832300b9f50c62c648e upstream.
Remove spinlock as atomic_t can be used instead. Note we use only 16
lower bits, upper bits are changed but we impilcilty cast to u16.
This fix possible deadlock on IBSS mode reproted by lockdep:
=================================
[ INFO: inconsistent lock state ]
3.4.0-wl+ #4 Not tainted
---------------------------------
inconsistent {IN-SOFTIRQ-W} -> {SOFTIRQ-ON-W} usage.
kworker/u:2/30374 [HC0[0]:SC0[0]:HE1:SE1] takes:
(&(&intf->seqlock)->rlock){+.?...}, at: [<f9979a20>] rt2x00queue_create_tx_descriptor+0x380/0x490 [rt2x00lib]
{IN-SOFTIRQ-W} state was registered at:
[<c04978ab>] __lock_acquire+0x47b/0x1050
[<c0498504>] lock_acquire+0x84/0xf0
[<c0835733>] _raw_spin_lock+0x33/0x40
[<f9979a20>] rt2x00queue_create_tx_descriptor+0x380/0x490 [rt2x00lib]
[<f9979f2a>] rt2x00queue_write_tx_frame+0x1a/0x300 [rt2x00lib]
[<f997834f>] rt2x00mac_tx+0x7f/0x380 [rt2x00lib]
[<f98fe363>] __ieee80211_tx+0x1b3/0x300 [mac80211]
[<f98ffdf5>] ieee80211_tx+0x105/0x130 [mac80211]
[<f99000dd>] ieee80211_xmit+0xad/0x100 [mac80211]
[<f9900519>] ieee80211_subif_start_xmit+0x2d9/0x930 [mac80211]
[<c0782e87>] dev_hard_start_xmit+0x307/0x660
[<c079bb71>] sch_direct_xmit+0xa1/0x1e0
[<c0784bb3>] dev_queue_xmit+0x183/0x730
[<c078c27a>] neigh_resolve_output+0xfa/0x1e0
[<c07b436a>] ip_finish_output+0x24a/0x460
[<c07b4897>] ip_output+0xb7/0x100
[<c07b2d60>] ip_local_out+0x20/0x60
[<c07e01ff>] igmpv3_sendpack+0x4f/0x60
[<c07e108f>] igmp_ifc_timer_expire+0x29f/0x330
[<c04520fc>] run_timer_softirq+0x15c/0x2f0
[<c0449e3e>] __do_softirq+0xae/0x1e0
irq event stamp: 18380437
hardirqs last enabled at (18380437): [<c0526027>] __slab_alloc.clone.3+0x67/0x5f0
hardirqs last disabled at (18380436): [<c0525ff3>] __slab_alloc.clone.3+0x33/0x5f0
softirqs last enabled at (18377616): [<c0449eb3>] __do_softirq+0x123/0x1e0
softirqs last disabled at (18377611): [<c041278d>] do_softirq+0x9d/0xe0
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&(&intf->seqlock)->rlock);
<Interrupt>
lock(&(&intf->seqlock)->rlock);
*** DEADLOCK ***
4 locks held by kworker/u:2/30374:
#0: (wiphy_name(local->hw.wiphy)){++++.+}, at: [<c045cf99>] process_one_work+0x109/0x3f0
#1: ((&sdata->work)){+.+.+.}, at: [<c045cf99>] process_one_work+0x109/0x3f0
#2: (&ifibss->mtx){+.+.+.}, at: [<f98f005b>] ieee80211_ibss_work+0x1b/0x470 [mac80211]
#3: (&intf->beacon_skb_mutex){+.+...}, at: [<f997a644>] rt2x00queue_update_beacon+0x24/0x50 [rt2x00lib]
stack backtrace:
Pid: 30374, comm: kworker/u:2 Not tainted 3.4.0-wl+ #4
Call Trace:
[<c04962a6>] print_usage_bug+0x1f6/0x220
[<c0496a12>] mark_lock+0x2c2/0x300
[<c0495ff0>] ? check_usage_forwards+0xc0/0xc0
[<c04978ec>] __lock_acquire+0x4bc/0x1050
[<c0527890>] ? __kmalloc_track_caller+0x1c0/0x1d0
[<c0777fb6>] ? copy_skb_header+0x26/0x90
[<c0498504>] lock_acquire+0x84/0xf0
[<f9979a20>] ? rt2x00queue_create_tx_descriptor+0x380/0x490 [rt2x00lib]
[<c0835733>] _raw_spin_lock+0x33/0x40
[<f9979a20>] ? rt2x00queue_create_tx_descriptor+0x380/0x490 [rt2x00lib]
[<f9979a20>] rt2x00queue_create_tx_descriptor+0x380/0x490 [rt2x00lib]
[<f997a5cf>] rt2x00queue_update_beacon_locked+0x5f/0xb0 [rt2x00lib]
[<f997a64d>] rt2x00queue_update_beacon+0x2d/0x50 [rt2x00lib]
[<f9977e3a>] rt2x00mac_bss_info_changed+0x1ca/0x200 [rt2x00lib]
[<f9977c70>] ? rt2x00mac_remove_interface+0x70/0x70 [rt2x00lib]
[<f98e4dd0>] ieee80211_bss_info_change_notify+0xe0/0x1d0 [mac80211]
[<f98ef7b8>] __ieee80211_sta_join_ibss+0x3b8/0x610 [mac80211]
[<c0496ab4>] ? mark_held_locks+0x64/0xc0
[<c0440012>] ? virt_efi_query_capsule_caps+0x12/0x50
[<f98efb09>] ieee80211_sta_join_ibss+0xf9/0x140 [mac80211]
[<f98f0456>] ieee80211_ibss_work+0x416/0x470 [mac80211]
[<c0496d8b>] ? trace_hardirqs_on+0xb/0x10
[<c077683b>] ? skb_dequeue+0x4b/0x70
[<f98f207f>] ieee80211_iface_work+0x13f/0x230 [mac80211]
[<c045cf99>] ? process_one_work+0x109/0x3f0
[<c045d015>] process_one_work+0x185/0x3f0
[<c045cf99>] ? process_one_work+0x109/0x3f0
[<f98f1f40>] ? ieee80211_teardown_sdata+0xa0/0xa0 [mac80211]
[<c045ed86>] worker_thread+0x116/0x270
[<c045ec70>] ? manage_workers+0x1e0/0x1e0
[<c0462f64>] kthread+0x84/0x90
[<c0462ee0>] ? __init_kthread_worker+0x60/0x60
[<c083d382>] kernel_thread_helper+0x6/0x10
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 69aaedd3cfd23b2c732e3cf1227370a35f5c89d4 upstream.
MacBook Pro models with BCM4331 wireless have been found to have the ext
PA lines disabled after resuming from S3 without external power attach.
This causes them to be unable to transmit. Add a workaround to ensure
that the ext PA lines are enabled on BCM4331. Also extend all handling
of ext PA line muxing to BCM43431 as is done in the Broadcom SDK.
BugLink: http://bugs.launchpad.net/bugs/925577
Cc: Arend van Spriel <arend@broadcom.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d012d04e4d6312ea157b6cf19e9689af934f5aa7 upstream.
This feature has been reported to be buggy and enabled by
default. We therefore need to disable it manually.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d6ee27eb13beab94056e0de52d81220058ca2297 upstream.
When we remove a key, we put a key index which was supposed
to tell the fw that we are actually removing the key. But
instead the fw took that index as a valid index and messed
up the SRAM of the device.
This memory corruption on the device mangled the data of
the SCD. The impact on the user is that SCD queue 2 got
stuck after having removed keys.
The message is the log that was printed is:
Queue 2 stuck for 10000ms
This doesn't seem to fix the higher queues that get stuck
from time to time.
Reviewed-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0e1fa7ef25004b9c1a14147bce61c15c2f1c6744 upstream.
Otherwise the LEDs stick around and cause issues the
next time around since they're still there but not
really hooked up.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fcb6ff5e2cb83e1de10631f6621f45ca3401bf61 upstream.
If CONFIG_PM_SLEEP is disabled, then iwlwifi doesn't
support suspend/resume handlers and thus mac80211
(correctly) refuses advertising WoWLAN. Disable
WoWLAN in the driver in this case.
Reported-by: Sebastian Kemper <sebastian_ml@gmx.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a393c730ab69617c3291a3b0b2a228c9be2fc28c upstream.
A regression was introduced in the 3.3 rc series, commit
"drm/ttm: simplify memory accounting for ttm user v2",
causing the metadata of buffer objects created using the ttm_bo_create()
function to be accounted twice.
That causes massive leaks with the vmwgfx driver running for example
SpecViewperf Catia-03 test 2, eventually killing the app.
Furthermore, the same commit introduces a regression where
metadata accounting is leaked if a buffer object is
initialized with an illegal size. This is also fixed with this commit.
v2: Fixed an error path and removed an unused variable.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 121daad8fd1dce63076fa55aaedd5dc3f981b334 upstream.
Data valid gets cleared by reading the ISR (status register) and NOT from
reading ODATA (data register). A new data word can become available between
checking ISR and reading ODATA, causing us to reuse the same data word next
time atmel_trng_read() gets called, if that happens before the following
data word is ready.
With this fixed, rngtest no longer complains of 'Continous run' errors.
Before:
rngtest -c 1000 < /dev/hwrng
rngtest 3
Copyright (c) 2004 by Henrique de Moraes Holschuh
This is free software; see the source for copying conditions. There is NO warr.
rngtest: starting FIPS tests...
rngtest: bits received from input: 20000032
rngtest: FIPS 140-2 successes: 923
rngtest: FIPS 140-2 failures: 77
rngtest: FIPS 140-2(2001-10-10) Monobit: 0
rngtest: FIPS 140-2(2001-10-10) Poker: 0
rngtest: FIPS 140-2(2001-10-10) Runs: 1
rngtest: FIPS 140-2(2001-10-10) Long run: 0
rngtest: FIPS 140-2(2001-10-10) Continuous run: 76
rngtest: input channel speed: (min=721.402; avg=46003.510; max=49321.338)Kibitss
rngtest: FIPS tests speed: (min=11.442; avg=12.714; max=12.801)Mibits/s
rngtest: Program run time: 1931860 microseconds
After:
rngtest -c 1000 < /dev/hwrng
rngtest 3
Copyright (c) 2004 by Henrique de Moraes Holschuh
This is free software; see the source for copying conditions. There is NO warr.
rngtest: starting FIPS tests...
rngtest: bits received from input: 20000032
rngtest: FIPS 140-2 successes: 1000
rngtest: FIPS 140-2 failures: 0
rngtest: FIPS 140-2(2001-10-10) Monobit: 0
rngtest: FIPS 140-2(2001-10-10) Poker: 0
rngtest: FIPS 140-2(2001-10-10) Runs: 0
rngtest: FIPS 140-2(2001-10-10) Long run: 0
rngtest: FIPS 140-2(2001-10-10) Continuous run: 0
rngtest: input channel speed: (min=777.518; avg=36988.482; max=43115.342)Kibitss
rngtest: FIPS tests speed: (min=11.951; avg=12.715; max=12.887)Mibits/s
rngtest: Program run time: 2035543 microseconds
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Reported-by: George Pontis <GPontis@z9.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 67384fe3fd450536342330f684ea1f7dcaef8130 upstream.
This seems to come on Gigabyte H55M-S2V and was discovered through the
https://bugs.freedesktop.org/show_bug.cgi?id=50381 debugging.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=50381
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c3b20037926e607b6cdaecbf9d3103e2ca63bc31 upstream.
When we reset the ring control registers, including the HEAD and TAIL of
the ring, we also need to reset associated state. In this instance, we
were failing to reset the cached value of ring->last_retired_head and so
upon the first request for more space following a resume would
potentially (depending on a narrow race window) believe that the HEAD had
advanced much further than reality.
This is a regression from:
commit a71d8d94525e8fd855c0466fb586ae1cb008f3a2
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Wed Feb 15 11:25:36 2012 +0000
drm/i915: Record the tail at each request and use it to estimate the head
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a6a17859f1bdf607650ee055101f54c5f207762b upstream.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6cb49835da0426f69a2931bc2a0a8156344b0e41 upstream.
We have one bug report from a validation team that we get the eDP
panel sequencing still somewhat wrong: We need to enable VDD while
switching off the panel and backlight. Unfortunately that reporter
seems to have fallen off the earth :(
For another reporter this actually fixes a black panel issue because
without this the backlight/panel gets confused and doesn't light up
again.
v2: I've forgotten to remove the vdd_off call in panel_off which is
now bogus. This essentially reverts
commit 17038de5f16569a25343cf68668f3b657eafb00e
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Mon Apr 16 22:43:42 2012 +0100
drm/i915/dp: Flush any outstanding work to turn the VDD off
v3: the current panel_off code forces off the vdd power, too. Which is
bogus and resulted in some funny warnings later on when we've tried to
do aux channel communications with just the vdd forced on. Fix this,
too.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=46312
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=43163
Tested-by: Vincent Frentzel <zcecc22@gmail.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 17038de5f16569a25343cf68668f3b657eafb00e upstream.
As we may kick off a delayed workqueue task to switch of the VDD lines, we
need to complete that task prior to turning off the panel (which itself
depends upon VDD being off).
v2: Don't cancel the outstanding work as this may trigger a deadlock
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Keith Packard <keithp@keithp.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 89ba829e38bd500f438bc08af4229204c8ed7f35 upstream.
Media turbo requests can either use RPVSWREQ or RPNSWREQ to indicate
what the interrupt handler should do. Since we only deal with the
latter in our turbo code, make the media engine use that for turbo
requests.
Tested-by: Joe Bloggsian <joebloggsian@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f380f2c4a12e913356bd49f8790ec1063c4fe9f8 upstream.
This driver disables interrupt just after requesting it and enables it
later, after interface is up. However currently there is a time window
between request_irq() and disable_irq() where if interrupt arrives, the
driver oopses because it's not yet ready to process it. This can be
reproduced by inserting the module, associating and removing the module
multiple times.
Eliminate this race by setting IRQF_NOAUTOEN flag before request_irq().
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit aba336bd1d46d6b0404b06f6915ed76150739057 upstream.
The new merge_bvec_fn which calls the corresponding function
in subsidiary devices requires that mddev->merge_check_needed
be set if any child has a merge_bvec_fn.
However were were only setting that when a device was hot-added,
not when a device was present from the start.
This bug was introduced in 3.4 so patch is suitable for 3.4.y
kernels. However that are conflicts in raid10.c so a separate
patch will be needed for 3.4.y.
Reported-by: Sebastian Riemer <sebastian.riemer@profitbricks.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c5971456964290da7e98222892797b71ef793e62 upstream.
We only need to regenerate the sysfs files when the capacity units
change, avoid the update otherwise.
The origin of this issue is dates way back to 2.6.38:
da8aeb92d4853f37e281f11fddf61f9c7d84c3cd
(ACPI / Battery: Update information on info notification and resume)
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Tested-by: Ralf Jung <post@ralfj.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit eee53537c476c947bf7faa1c916d2f5a0ae8ec93 upstream.
In the error path of the ppr_notifer it can happen that the
iommu->lock is taken recursivly. This patch fixes the
problem by releasing the iommu->lock before any notifier is
invoked. This also requires to move the erratum workaround
for the ppr-log (interrupt may be faster than data in the log)
one function up.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c1bf94ec1e12d76838ad485158aecf208ebd8fb9 upstream.
At some point pci_get_bus_and_slot started to enable
interrupts. Since this function is used in the
amd_iommu_resume path it will enable interrupts on resume
which causes a warning. The fix will use a cached pointer
to the root-bridge to re-enable the IOMMU in case the BIOS
is broken.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d430f7dbf7bd6aaaa40c0660b3204df8cf07b22b upstream.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bb4091558228ff4a3e02328c931e683fc7f08722 upstream.
Locking mutex in different orders just screams for
deadlocks, and some testing showed that it is actually
quite easy to trigger them.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0aecb5a4ba1ea4167f31d1790eec027f1e658f2d upstream.
This is based on info released by AMD, should allow using audio in much
more cases.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 9dae31009b1a00d926c6fe032d5a88099620adc3 ]
asix driver drops 8021Q full size frames because it doesn't take into
account VLAN header size.
Tested on AX88772 adapter.
Signed-off-by: Eric Dumazet <edumazet@google.com>
CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CC: Allan Chou <allan@asix.com.tw>
CC: Trond Wuellner <trond@chromium.org>
CC: Grant Grundler <grundler@chromium.org>
CC: Paul Stewart <pstew@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0824db38e515644f8d1bfd64adbd7cb2c6ea7c62 upstream.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a8ff3ee211fccf708e1911bbc096625453ebf759 upstream.
This imbalance may cause hangs when TTM is trying to swap out a buffer
that is already on the delayed delete list.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 95c4b23ec4e2fa5604df229ddf134e31d7b3b378 upstream.
Without this bit sets we get broken rendering and
lockups.
fglrx sets this bit.
Bugs that should be fixed by this patch :
https://bugs.freedesktop.org/show_bug.cgi?id=49792
https://bugzilla.kernel.org/show_bug.cgi?id=43207
https://bugs.freedesktop.org/show_bug.cgi?id=39282
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0b8c30bc4943137a4a36b9cb059b1cc684f5d702 upstream.
Need to program an additional VM register. This doesn't not currently
cause any problems, but allows us to program the proper backend
map in a subsequent patch which should improve performance on these
asics.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 29d654067a98c1cb8874c774e5fd799a038af8a6 upstream.
While there are cards with more than 8 mem banks, the max
number of banks from a tiling perspective is 8, so cap
the tiling config at 8 banks.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=43448
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9b00147d9f2ba137ce74b66b768a8312be0b6781 upstream.
radeon_cs_parser_init is called by both the legacy UMS
CS ioctl and the KMS CS ioctl. Protect KMS specific
pieces of the code by checking that rdev is not NULL.
Reported-by: Michael Burian <michael.burian@sbg.at>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4a43faf54e9173b6acce37cf7f053fc9515a2cdf upstream.
Since commit 6a918bade9dab40aaef80559bd1169c69e8d69cb, the mxc_nand driver
fails with:
Driver must set ecc.strength when using hardware ECC
This is because nand_scan_tail checks for correct ecc strength
settings, so we must set them up before nand_scan_tail.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2e24e32e2759348c9290404abad4f729f791bfad upstream.
The 'mtd_writev' interface calls the function assigned
to the '_write' field of a given mtd device if that is
not NULL. The block2mtd driver sets the '_writev' field
to the 'mtd_writev' function itself and thus causes a
endless loop.
This is caused by 1dbebd32562b3c2caeca35960e5cb00bfcc12900
(mtd: harmonize mtd_writev usage).
Remove the assignment from the block2mtd driver to fix the
issue.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2e929d001e85126d9267de373d4b76014789661d upstream.
MTD_OF_PARTS and the default setting is not working due to using 'Y'
instead of 'y', introduced in commit
d6137badeff1ef64b4e0092ec249ebdeaeb3ff37. This made our board, and
possibly other boards using DTS defined partitions and not having
CONFIG_MTD_OF_PARTS=y defined in the defconfig, fail to mount root.
Signed-off-by: Frank Svendsboe <frank.svendsboe@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 34a5704d91d6f8376a4c0a0143a1dd3eb3ccb37e upstream.
It seems there is a bug in scan_read_raw_oob() in nand_bbt.c which
should cause wrong functioning of NAND_BBT_SCANALLPAGES option.
Artem: the patch did not apply and I had to amend it a bit.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9ca3cc6f3026946ba655e863ca2096339e667639 upstream.
skb_defer_rx_timestamp was called with a freshly allocated skb but must
be called with rskb instead.
Signed-off-by: Stephan Gatzka <stephan@gatzka.org>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3347111999870c37eab1b969e90af9fdaf0334ba upstream.
This box has DisplayPort and VGA, but no LVDS. Product specs are at
http://h10010.www1.hp.com/wwpc/us/en/sm/WF25a/12454-12454-321959-338927-3640406-4282707.html?dnr=1
and dmidecode output can be found at http://www.getslash.de/bug_attachments/dmidecode-t5740e.txt
Signed-off-by: Jan-Benedict Glaw <jbglaw@getslash.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bf2125e2f7e931b50a6c76ba0435ba001409ccbf upstream.
Otherwise the hw will get confused and result in a black screen.
This regression has been most likely introduce in
commit 974b93315b2213b74a42a87e8a9d4fc8c0dbe90c
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Sun Sep 5 00:44:20 2010 +0100
drm/i915/tv: Poll for DAC state change
That commit replace the first msleep(20) with a busy-loop, but failed
to keep the 2nd msleep around. Later on we've replaced all these
msleep(20) by proper vblanks.
For reference also see the commit in xf86-video-intel:
commit 1142be53eb8d2ee8a9b60ace5d49f0ba27332275
Author: Jesse Barnes <jbarnes@hobbes.lan>
Date: Mon Jun 9 08:52:59 2008 -0700
Fix TV programming: add vblank wait after TV_CTL writes
Fxies FDO bug #14000; we need to wait for vblank after
writing TV_CTL or following "DPMS on" calls may not actually enable the output.
v2: As suggested by Chris Wilson, add a small comment to ensure that
no one accidentally removes this vblank wait again - there really
seems to be no sane explanation for why we need it, but it is
required.
Launchpad: https://bugs.launchpad.net/ubuntu/+source/xserver-xorg-video-intel/+bug/763688
Reported-and-Tested-by: Robert Lowery <rglowery@exemail.com.au>
Cc: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9589919fb3d269d4202a112b197468c7db1f97a3 upstream.
These 2 modes were removed by mistake during a clean up.
So, now it is time to add them back. For further info about
supported mode and standard timing table please check:
VOL_3_display_registers_updated.pdf at intellinuxgraphics.org.
Note that this regression has been introduce in
commit 55a6713b3f30a5024056027e9dbf03ac8f13bfc9
Author: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Date: Thu Dec 15 14:47:33 2011 -0200
drm/i915: Removing TV Out modes.
and this commit partially reverts it by re-adding the wrongly removed
modes.
Reported-by: Robert Lowery <rglowery@exemail.com.au>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: Pimped commit message to cite the commit that introduced this
regression.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 59d92bfa5f0cdf57f82f5181b0ad6af75c3fdf41 upstream.
We've simply ignored this, which isn't too great. With this, interlaced
1080i works on my HDMI screen connected through sdvo. For no apparent
reason anything else still doesn't work as it should.
While at it, give these magic numbers in the dtd proper names and
add a comment that they match with EDID detailed timings.
v2: Actually use the right bit for interlaced.
Tested-by: Peter Ross <pross@xvid.org>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
