| Age | Commit message (Collapse) | Author |
|---|
|
commit c9651e70ad0aa499814817cbf3cc1d0b806ed3a1 upstream.
Since 3.2.12 and 3.3, some systems are failing to boot with a BUG_ON.
Some other systems using the pata_jmicron driver fail to boot because no
disks are detected. Passing pcie_aspm=force on the kernel command line
works around it.
The cause: commit 4949be16822e ("PCI: ignore pre-1.1 ASPM quirking when
ASPM is disabled") changed the behaviour of pcie_aspm_sanity_check() to
always return 0 if aspm is disabled, in order to avoid cases where we
changed ASPM state on pre-PCIe 1.1 devices.
This skipped the secondary function of pcie_aspm_sanity_check which was
to avoid us enabling ASPM on devices that had non-PCIe children, causing
trouble later on. Move the aspm_disabled check so we continue to honour
that scenario.
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=42979 and
http://bugs.debian.org/665420
Reported-by: Romain Francoise <romain@orebokech.com> # kernel panic
Reported-by: Chris Holland <bandidoirlandes@gmail.com> # disk detection trouble
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Tested-by: Hatem Masmoudi <hatem.masmoudi@gmail.com> # Dell Latitude E5520
Tested-by: janek <jan0x6c@gmail.com> # pata_jmicron with JMB362/JMB363
[jn: with more symptoms in log message]
Signed-off-by: Jonathan Nieder <jrnieder@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 49d4bcaddca977fffdea8b0b71f6e5da96dac78e upstream.
When DMA is enabled, sh-sci transfer begins with
uart_start()
sci_start_tx()
if (cookie_tx < 0) schedule_work()
Then, starts DMA when wq scheduled, -- (A)
process_one_work()
work_fn_rx()
cookie_tx = desc->submit_tx()
And finishes when DMA transfer ends, -- (B)
sci_dma_tx_complete()
async_tx_ack()
cookie_tx = -EINVAL
(possible another schedule_work())
This A to B sequence is not reentrant, since controlling variables
(for example, cookie_tx above) are not queues nor lists. So, they
must be invoked as A B A B..., otherwise results in kernel crash.
To ensure the sequence, sci_start_tx() seems to test if cookie_tx < 0
(represents "not used") to call schedule_work().
But cookie_tx will not be set (to a cookie, also means "used") until
in the middle of work queue scheduled function work_fn_tx().
This gap between the test and set allows the breakage of the sequence
under the very frequently call of uart_start().
Another gap between async_tx_ack() and another schedule_work() results
in the same issue, too.
This patch introduces a new condition "cookie_tx == 0" just to mark
it is "busy" and assign it within spin-locked region to fill the gaps.
Signed-off-by: Takashi Yoshii <takashi.yoshii.zj@renesas.com>
Reviewed-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4a649903f91232d02284d53724b0a45728111767 upstream.
Richard Weinberger noticed that on some RTC hardware that
doesn't support UIE mode, due to coarse granular alarms
(like 1minute resolution), the current virtualized RTC
support doesn't properly error out when UIE is enabled.
Instead the current code queues an alarm for the next second,
but it won't fire until up to a miniute later.
This patch provides a generic way to flag this sort of hardware
and fixes the issue on the mpc5121 where Richard noticed the
problem.
Reported-by: Richard Weinberger <richard@nod.at>
Tested-by: Richard Weinberger <richard@nod.at>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 5676cc7bfe1e388e87843f71daa229610385b41e ]
Some BIOS's don't setup power management correctly (what else is
new) and don't allow use of PCI Express power control. Add a special
exception module parameter to allow working around this issue.
Based on slightly different patch by Knut Petersen.
Reported-by: Arkadiusz Miskiewicz <arekm@maven.pl>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3fa016a0b5c5237e9c387fc3249592b2cb5391c6 upstream.
Looking at hibernate overwriting I though it looked like a cursor,
so I tracked down this missing piece to stop the cursor blink
timer. I've no idea if this is sufficient to fix the hibernate
problems people are seeing, but please test it.
Both radeon and nouveau have done this for a long time.
I've run this personally all night hib/resume cycles with no fails.
Reviewed-by: Keith Packard <keithp@keithp.com>
Reported-by: Petr Tesarik <kernel@tesarici.cz>
Reported-by: Stanislaw Gruszka <sgruszka@redhat.com>
Reported-by: Lots of misc segfaults after hibernate across the world.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=37142
Tested-by: Dave Airlie <airlied@redhat.com>
Tested-by: Bojan Smojver <bojan@rexursive.com>
Tested-by: Andreas Hartmann <andihartmann@01019freenet.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8da00edc1069f01c34510fa405dc15d96c090a3f upstream.
Fix typo in drivers/video/backlight/tosa_lcd.c
"tosa_lcd_reume" should be "tosa_lcd_resume".
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6f94a4c45a6f744383f9f695dde019998db3df55 upstream.
Avoid using the bi_next field for the holder of a cell when deferring
bios because a stacked device below might change it. Store the
holder in a new field in struct cell instead.
When a cell is created, the bio that triggered creation (the holder) was
added to the same bio list as subsequent bios. In some cases we pass
this holder bio directly to devices underneath. If those devices use
the bi_next field there will be trouble...
This also simplifies some code that had to work out which bio was the
holder.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b0988900bae9ecf968a8a8d086a9eec671a9517a upstream.
When we remove an entry from a node we sometimes rebalance with it's
two neighbours. This wasn't being done correctly; in some cases
entries have to move all the way from the right neighbour to the left
neighbour, or vice versa. This patch pretty much re-writes the
balancing code to fix it.
This code is barely used currently; only when you delete a thin
device, and then only if you have hundreds of them in the same pool.
Once we have discard support, which removes mappings, this will be used
much more heavily.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit aadbe266f2f89ccc68b52f4effc7b3a8b29521ef upstream.
Call the correct exit function on failure in dm_exception_store_init.
Signed-off-by: Andrei Warkentin <andrey.warkentin@gmail.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 72c6e7afc43e19f68a31dea204fc366624d6eee9 upstream.
Always set io->error to -EIO when an error is detected in dm-crypt.
There were cases where an error code would be set only if we finish
processing the last sector. If there were other encryption operations in
flight, the error would be ignored and bio would be returned with
success as if no error happened.
This bug is present in kcryptd_crypt_write_convert, kcryptd_crypt_read_convert
and kcryptd_async_done.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit aeb2deae2660a1773c83d3c6e9e6575daa3855d6 upstream.
This patch fixes a possible deadlock in dm-crypt's mempool use.
Currently, dm-crypt reserves a mempool of MIN_BIO_PAGES reserved pages.
It allocates first MIN_BIO_PAGES with non-failing allocation (the allocation
cannot fail and waits until the mempool is refilled). Further pages are
allocated with different gfp flags that allow failing.
Because allocations may be done in parallel, this code can deadlock. Example:
There are two processes, each tries to allocate MIN_BIO_PAGES and the processes
run simultaneously.
It may end up in a situation where each process allocates (MIN_BIO_PAGES / 2)
pages. The mempool is exhausted. Each process waits for more pages to be freed
to the mempool, which never happens.
To avoid this deadlock scenario, this patch changes the code so that only
the first page is allocated with non-failing gfp mask. Allocation of further
pages may fail.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 017d213f649c6775e4a4349e50a5631a4e4c7308 upstream.
Using the bpc (bits per color) specified by the monitor
can cause problems in some cases. Until we get a better
handle on how to deal with those cases, just use a bpc of 8.
Reported-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d2cb87c23e8514ca49c85adc5924999927bb9494 upstream.
The jack detection on WM1811 is often required during system suspend, add
it as another check when deciding if we should suspend.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 81b279d80a63628e580c71a31d30a8c3b3047ad4 upstream.
Unbanked GPIO IRQ handling code made a copy of just
the irq_chip structure for GPIO IRQ lines which caused
problems after the generic IRQ chip conversion because
there was no valid irq_chip_type structure with the
right "regs" populated. irq_gc_mask_set_bit() was
therefore accessing random addresses.
Fix it by making a copy of irq_chip_type structure
instead. This will ensure sane register offsets.
Reported-by: Jon Povey <Jon.Povey@racelogic.co.uk>
Tested-by: Jon Povey <Jon.Povey@racelogic.co.uk>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ab2dde9924dd1ddb791fa8b14aa52e1df681e20c upstream.
Unbanked GPIO irq setup code was overwriting chip_data leading
to the following oops on request_irq()
Unable to handle kernel paging request at virtual address febfffff
pgd = c22dc000
[febfffff] *pgd=00000000
Internal error: Oops: 801 [#1] PREEMPT
Modules linked in: mcu(+) edmak irqk cmemk
CPU: 0 Not tainted (3.0.0-rc7+ #93)
PC is at irq_gc_mask_set_bit+0x68/0x7c
LR is at vprintk+0x22c/0x484
pc : [<c0080c0c>] lr : [<c00457e0>] psr: 60000093
sp : c33e3ba0 ip : c33e3af0 fp : c33e3bc4
r10: c04555bc r9 : c33d4340 r8 : 60000013
r7 : 0000002d r6 : c04555bc r5 : fec67010 r4 : 00000000
r3 : c04734c8 r2 : fec00000 r1 : ffffffff r0 : 00000026
Flags: nZCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment user
Control: 0005317f Table: 822dc000 DAC: 00000015
Process modprobe (pid: 526, stack limit = 0xc33e2270)
Stack: (0xc33e3ba0 to 0xc33e4000)
3ba0: 00000000 c007d3d4 c33e3bcc c04555bc c04555bc c33d4340 c33e3bdc c33e3bc8
3bc0: c007f5f8 c0080bb4 00000000 c04555bc c33e3bf4 c33e3be0 c007f654 c007f5c0
3be0: 00000000 c04555bc c33e3c24 c33e3bf8 c007e6e8 c007f618 c01f2284 c0350af8
3c00: c0405214 bf016c98 00000001 00000000 c33dc008 0000002d c33e3c54 c33e3c28
3c20: c007e888 c007e408 00000001 c23ef880 c33dc000 00000000 c33dc080 c25caa00
3c40: c0487498 bf017078 c33e3c94 c33e3c58 bf016b44 c007e7d4 bf017078 c33dc008
3c60: c25caa08 c33dc008 c33e3c84 bf017484 c25caa00 c25caa00 c01f5f48 c25caa08
3c80: c0496d60 bf017484 c33e3ca4 c33e3c98 c022a698 bf01692c c33e3cd4 c33e3ca8
3ca0: c01f5d88 c022a688 00000000 bf017484 c25caa00 c25caa00 c01f5f48 c25caa08
3cc0: c0496d60 00000000 c33e3cec c33e3cd8 c01f5f8c c01f5d10 00000000 c33e3cf0
3ce0: c33e3d14 c33e3cf0 c01f5210 c01f5f58 c303cb48 c25ecf94 c25caa00 c25caa00
3d00: c25caa34 c33e3dd8 c33e3d34 c33e3d18 c01f6044 c01f51b8 c0496d3c c25caa00
3d20: c044e918 c33e3dd8 c33e3d44 c33e3d38 c01f4ff4 c01f5fcc c33e3d94 c33e3d48
3d40: c01f3d10 c01f4fd8 00000000 c044e918 00000000 00000000 c01f52c0 c034d570
3d60: c33e3d84 c33e3d70 c022bf84 c25caa00 00000000 c044e918 c33e3dd8 c25c2e00
3d80: c0496d60 bf01763c c33e3db4 c33e3d98 c022b1a0 c01f384c c25caa00 c33e3dd8
3da0: 00000000 c33e3dd8 c33e3dd4 c33e3db8 c022b27c c022b0e8 00000000 bf01763c
3dc0: c0451c80 c33e3dd8 c33e3e34 c33e3dd8 bf016f60 c022b210 5f75636d 746e6f63
3de0: 006c6f72 00000000 00000000 00000000 00000000 00000000 00000000 bf0174bc
3e00: 00000000 00989680 00000000 00000020 c0451c80 c0451c80 bf0174dc c01f5eb0
3e20: c33f0f00 bf0174dc c33e3e44 c33e3e38 c01f72f4 bf016e2c c33e3e74 c33e3e48
3e40: c01f5d88 c01f72e4 00000000 c0451c80 c0451cb4 bf0174dc c01f5eb0 c33f0f00
3e60: c0473100 00000000 c33e3e94 c33e3e78 c01f5f44 c01f5d10 00000000 c33e3e98
3e80: bf0174dc c01f5eb0 c33e3ebc c33e3e98 c01f5534 c01f5ec0 c303c038 c3061c30
3ea0: 00003cd8 00098258 bf0174dc c0462ac8 c33e3ecc c33e3ec0 c01f5bec c01f54dc
3ec0: c33e3efc c33e3ed0 c01f4d30 c01f5bdc bf0173a0 c33e2000 00003cd8 00098258
3ee0: bf0174dc c33e2000 c00301a4 bf019000 c33e3f1c c33e3f00 c01f6588 c01f4c8c
3f00: 00003cd8 00098258 00000000 c33e2000 c33e3f2c c33e3f20 c01f777c c01f6524
3f20: c33e3f3c c33e3f30 bf019014 c01f7740 c33e3f7c c33e3f40 c002f3ec bf019010
3f40: 00000000 00003cd8 00098258 bf017518 00000000 00003cd8 00098258 bf017518
3f60: 00000000 c00301a4 c33e2000 00000000 c33e3fa4 c33e3f80 c007b934 c002f3c4
3f80: c00b307c c00b2f48 00003cd8 00000000 00000003 00000080 00000000 c33e3fa8
3fa0: c0030020 c007b8b8 00003cd8 00000000 00098288 00003cd8 00098258 00098240
3fc0: 00003cd8 00000000 00000003 00000080 00098008 00098028 00098288 00000001
3fe0: be892998 be892988 00013d7c 40178740 60000010 00098288 09089041 00200845
Backtrace:
[<c0080ba4>] (irq_gc_mask_set_bit+0x0/0x7c) from [<c007f5f8>] (irq_enable+0x48/0x58)
r6:c33d4340 r5:c04555bc r4:c04555bc
[<c007f5b0>] (irq_enable+0x0/0x58) from [<c007f654>] (irq_startup+0x4c/0x54)
r5:c04555bc r4:00000000
[<c007f608>] (irq_startup+0x0/0x54) from [<c007e6e8>] (__setup_irq+0x2f0/0x3cc)
r5:c04555bc r4:00000000
[<c007e3f8>] (__setup_irq+0x0/0x3cc) from [<c007e888>] (request_threaded_irq+0xc4/0x110)
r8:0000002d r7:c33dc008 r6:00000000 r5:00000001 r4:bf016c98
[<c007e7c4>] (request_threaded_irq+0x0/0x110) from [<bf016b44>] (mcu_spi_probe+0x228/0x37c [mcu])
[<bf01691c>] (mcu_spi_probe+0x0/0x37c [mcu]) from [<c022a698>] (spi_drv_probe+0x20/0x24)
[<c022a678>] (spi_drv_probe+0x0/0x24) from [<c01f5d88>] (driver_probe_device+0x88/0x1b0)
[<c01f5d00>] (driver_probe_device+0x0/0x1b0) from [<c01f5f8c>] (__device_attach+0x44/0x48)
[<c01f5f48>] (__device_attach+0x0/0x48) from [<c01f5210>] (bus_for_each_drv+0x68/0x94)
r5:c33e3cf0 r4:00000000
[<c01f51a8>] (bus_for_each_drv+0x0/0x94) from [<c01f6044>] (device_attach+0x88/0xa0)
r7:c33e3dd8 r6:c25caa34 r5:c25caa00 r4:c25caa00
[<c01f5fbc>] (device_attach+0x0/0xa0) from [<c01f4ff4>] (bus_probe_device+0x2c/0x4c)
r7:c33e3dd8 r6:c044e918 r5:c25caa00 r4:c0496d3c
[<c01f4fc8>] (bus_probe_device+0x0/0x4c) from [<c01f3d10>] (device_add+0x4d4/0x648)
[<c01f383c>] (device_add+0x0/0x648) from [<c022b1a0>] (spi_add_device+0xc8/0x128)
[<c022b0d8>] (spi_add_device+0x0/0x128) from [<c022b27c>] (spi_new_device+0x7c/0xb4)
r7:c33e3dd8 r6:00000000 r5:c33e3dd8 r4:c25caa00
[<c022b200>] (spi_new_device+0x0/0xb4) from [<bf016f60>] (mcu_probe+0x144/0x224 [mcu])
r7:c33e3dd8 r6:c0451c80 r5:bf01763c r4:00000000
[<bf016e1c>] (mcu_probe+0x0/0x224 [mcu]) from [<c01f72f4>] (platform_drv_probe+0x20/0x24)
[<c01f72d4>] (platform_drv_probe+0x0/0x24) from [<c01f5d88>] (driver_probe_device+0x88/0x1b0)
[<c01f5d00>] (driver_probe_device+0x0/0x1b0) from [<c01f5f44>] (__driver_attach+0x94/0x98)
[<c01f5eb0>] (__driver_attach+0x0/0x98) from [<c01f5534>] (bus_for_each_dev+0x68/0x94)
r7:c01f5eb0 r6:bf0174dc r5:c33e3e98 r4:00000000
[<c01f54cc>] (bus_for_each_dev+0x0/0x94) from [<c01f5bec>] (driver_attach+0x20/0x28)
r7:c0462ac8 r6:bf0174dc r5:00098258 r4:00003cd8
[<c01f5bcc>] (driver_attach+0x0/0x28) from [<c01f4d30>] (bus_add_driver+0xb4/0x258)
[<c01f4c7c>] (bus_add_driver+0x0/0x258) from [<c01f6588>] (driver_register+0x74/0x158)
[<c01f6514>] (driver_register+0x0/0x158) from [<c01f777c>] (platform_driver_register+0x4c/0x60)
r7:c33e2000 r6:00000000 r5:00098258 r4:00003cd8
[<c01f7730>] (platform_driver_register+0x0/0x60) from [<bf019014>] (mcu_init+0x14/0x20 [mcu])
[<bf019000>] (mcu_init+0x0/0x20 [mcu]) from [<c002f3ec>] (do_one_initcall+0x38/0x170)
[<c002f3b4>] (do_one_initcall+0x0/0x170) from [<c007b934>] (sys_init_module+0x8c/0x1a4)
[<c007b8a8>] (sys_init_module+0x0/0x1a4) from [<c0030020>] (ret_fast_syscall+0x0/0x2c)
r7:00000080 r6:00000003 r5:00000000 r4:00003cd8
Code: e1844003 e585400c e596300c e5932064 (e7814002)
Fix the issue.
Reported-by: Jon Povey <Jon.Povey@racelogic.co.uk>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8276536cec38bc6bde30d0aa67716f22b9b9705a upstream.
This function should be capable of both enabling and disabling interrupts
based upon the *enable* parameter. Right now the function only enables
the interrupt and *enable* is not used at all. So add the interrupt
disable capability also using the parameter.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
parameter CONFIG_R8712_AP
commit 073863432f7eaa23c7c09733414d4be2eabf5eef upstream.
When this driver was upgraded to the vendor 20100831 version in
commit 93c55dda092c7 et al,, one listhead initialization was missed.
This broke complete operation of the driver whenever AP mode was
enabled. This fixes https://bugs.archlinux.org/task/27996.
The configuration parameter R8712_AP is misleading as the driver cannot
function as an AP without a heavily hacked version of hostapd. Thus, it
makes sense to remove the parameter; however the code and data configured
for the option is left in.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b0302aba812bcc39291cdab9ad7e37008f352a91 upstream.
This patch addresses a kernel bugzilla report and two recent mail threads.
The kernel bugzilla report is https://bugzilla.kernel.org/show_bug.cgi?id=42632,
which reports a udev timeout on boot.
The first mail thread, which was on LKML (http://lkml.indiana.edu/hypermail/
linux/kernel/1112.3/00965.html) was for a WARNING that occurs after a
suspend/resume cycle for rtl8192cu.
The scond mail thread (http://marc.info/?l=linux-wireless&m=132655490826766&w=2)
concerned changes in udev that break drivers that delay while firmware is loaded
on modprobe.
This patch converts all rtlwifi-based drivers to use the asynchronous firmware
loading mechanism. Drivers rtl8192ce, rtl8192cu and rtl8192de share a common
callback routine. Driver rtl8192se needs different handling of the firmware,
thus it has its own code.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 57d13370cfaf6017c68981e66ff5b3bf20a2705c upstream.
Make the MTU2 clocksource driver mark its device as "always on"
using pm_genpd_dev_always_on() to protect it from surprise power
removals.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Simon Horman <horms@verge.net.au>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 615a445f7f8a077c145e737864ae59a4d8717882 upstream.
Make the CMT clocksource driver mark its device as "always on"
using pm_genpd_dev_always_on() to protect it from surprise power
removals.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Simon Horman <horms@verge.net.au>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 2ee619f9487c2acc1efdf2c78e68e2bd51b635fa upstream.
Make the TMU clocksource driver mark its device as "always on"
using pm_genpd_dev_always_on() to protect it from surprise power
removals and make sh7372_add_standard_devices() add TMU devices on
sh7372 to the A4R power domain so that their "always on" flags
are taken into account as appropriate.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Simon Horman <horms@verge.net.au>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This is a backport of mainline commit
1e78a0c7fc92aee076965d516cf54475c39e9894.
The TMU device on the Mackerel board belongs to the A4R power domain
and loses power when the domain is turned off. Unfortunately, the
TMU driver is not prepared to cope with such situations and crashes
the system when that happens. To work around this problem introduce
a new helper function, pm_genpd_dev_always_on(), allowing a device
driver to mark its device as "always on" in case it belongs to a PM
domain, which will make the generic PM domains core code avoid
powering off the domain containing the device, both at run time and
during system suspend.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Simon Horman <horms@verge.net.au>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This is a backport of mainline commit
18dd2ece3cde14cfd42e95a89eb14016699a5f15.
Power domains that were off before hibernation shouldn't be turned on
during device restore, so prevent that from happening.
This change fixed up mainline commit
65533bbf63b4f37723fdfedc73d0653958973323
PM / Domains: Fix hibernation restore of devices, v2
that didn't include it by mistake.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This is a backport of mainline commit
65533bbf63b4f37723fdfedc73d0653958973323.
During resume from hibernation pm_genpd_restore_noirq() should only
power off domains whose suspend_power_off flags are set once and
not every time it is called for a device in the given domain.
Moreover, it shouldn't decrement genpd->suspended_count, because
that field is not touched during device freezing and therefore it is
always equal to 0 when pm_genpd_restore_noirq() runs for the first
device in the given domain.
This means pm_genpd_restore_noirq() may use genpd->suspended_count
to determine whether or not it it has been called for the domain in
question already in this cycle (it only needs to increment that
field every time it runs for this purpose) and whether or not it
should check if the domain needs to be powered off. For that to
work, though, pm_genpd_prepare() has to clear genpd->suspended_count
when it runs for the first device in the given domain (in which case
that flag need not be cleared during domain initialization).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3be5bb71fbf18f83cb88b54a62a78e03e5a4f30a upstream.
Remove unnecessary register access in mxl111sf_ep6_streaming_ctrl()
This code breaks driver operation in kernel 3.3 and later, although
it works properly in 3.2 Disable register access to 0x12 for now.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9ab2393fc3e460cd2040de1483918eb17abb822f upstream.
The D1F5 revision of the WinTV HVR-1900 uses a tda18271c2 tuner
instead of a tda18271c1 tuner as used in revision D1E9. To
account for this, we must hardcode the frontend configuration
to use the same IF frequency configuration for both revisions
of the device.
6MHz DVB-T is unaffected by this issue, as the recommended
IF Frequency configuration for 6MHz DVB-T is the same on both
c1 and c2 revisions of the tda18271 tuner.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Cc: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ef3d2dc366c8c32d58dbbf9898cfd4f853ff8fe0 upstream.
The au8522 driver programs the tuner after programming the demodulator,
but the tuner should be programmed first. This patch fixes this behavior.
EDIT: Apparantly Devin created a similar patch some time ago, but hasn't
submitted it for merge. I never saw his patch, but I thank him anyhow
for his efforts. In addition, Devin pointed out a flaw in my patch:
This newly generated patch takes Devin's comments into account.
Thanks-to: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2b49fad59513b07f976c9711b99f93ae74d081c5 upstream.
Commit b2a29b578d9c21b2e5c88020f830d3c42115c51d sets accidentally
supported delivery systems as DVB-T/T2 whilst it should be
DVB-S/S2. Due to that frontend cannot be used at all.
Reported-by: Jiří Zelenka <klacek@bubakov.net>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit abf9d005375d6c6160cc9c17e5dcac32e412c8dc upstream.
This patch fixes a regression in kernel 3.3 due to this patch:
http://patchwork.linuxtv.org/patch/8332/
That patch changes "#pragma pack(1)" with "__packed" attributes, but it is not
complete. In fact, in the as102 driver there are a lot of structs/unions
defined inside other structs/unions.
When the "__packed" attribute is applied only on the external struct, it will
not affect the internal struct definitions.
So the regression is fixed by specifiying the "__packed" attribute also on the
internal structs.
This patch should go into 3.3, as it fixes a regression introduced in the new
kernel version.
Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Signed-off-by: Ryley Angus <rangus@student.unimelb.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 34817174fca0c5512c2d5b6ea0fc37a0337ce1d8 upstream.
The error handling in lgdt3303_read_status() and lgdt330x_read_ucblocks()
doesn't work, because i2c_read_demod_bytes() returns a u8 and (err < 0)
is always false.
err = i2c_read_demod_bytes(state, 0x58, buf, 1);
if (err < 0)
return err;
Change the return type of i2c_read_demod_bytes() to int. Also change
the return value on error to -EIO to make (err < 0) work.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fc0900cbda9243957d812cd6b4cc87965f9fe75f upstream.
Wrong bit was used for sign extension which caused wrong end results.
Thanks to Andre for spotting this bug.
Reported-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9ddd592a191b32f2ee6c4b6ed2bd52665c3a49f5 upstream.
Unfortunatly the interrupts for the event log and the
peripheral page-faults are only enabled at boot but not
re-enabled at resume. Fix that.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cebd5fa4d3046d5b43ce1836a0120612822a7fb0 upstream.
Fix the following section warning in drivers/iommu/amd_iommu.c :
WARNING: vmlinux.o(.text+0x526e77): Section mismatch in reference from the function prealloc_protection_domains() to the function .init.text:alloc_passthrough_domain()
The function prealloc_protection_domains() references
the function __init alloc_passthrough_domain().
This is often because prealloc_protection_domains lacks a __init
annotation or the annotation of alloc_passthrough_domain is wrong.
Signed-off-by: Steffen Persvold <sp@numascale.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5d5440a835710d09f0ef18da5000541ec98b537a upstream.
URB unlinking is always racing with its completion and tx_complete
may be called before or during running usb_unlink_urb, so tx_complete
must not clear urb->dev since it will be used in unlink path,
otherwise invalid memory accesses or usb device leak may be caused
inside usb_unlink_urb.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0956a8c20b23d429e79ff86d4325583fc06f9eb4 upstream.
Commit 4231d47e6fe69f061f96c98c30eaf9fb4c14b96d(net/usbnet: avoid
recursive locking in usbnet_stop()) fixes the recursive locking
problem by releasing the skb queue lock, but it makes usb_unlink_urb
racing with defer_bh, and the URB to being unlinked may be freed before
or during calling usb_unlink_urb, so use-after-free problem may be
triggerd inside usb_unlink_urb.
The patch fixes the use-after-free problem by increasing URB
reference count with skb queue lock held before calling
usb_unlink_urb, so the URB won't be freed until return from
usb_unlink_urb.
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Oliver Neukum <oliver@neukum.org>
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7eb3aa65853e1b223bfc786b023b702018cb76c0 upstream.
The 'find_wl_entry()' function expects the maximum difference as the second
argument, not the maximum absolute value. So the "unknown" eraseblock picking
was incorrect, as Shmulik Ladkani spotted. This patch fixes the issue.
Reported-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Reviewed-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a29852be492d61001d86c6ebf5fff9b93d7b4be9 upstream.
Two bad things can happen in ubi_scan():
1. If kmem_cache_create() fails we jump to out_si and call
ubi_scan_destroy_si() which calls kmem_cache_destroy().
But si->scan_leb_slab is NULL.
2. If process_eb() fails we jump to out_vidh, call
kmem_cache_destroy() and ubi_scan_destroy_si() which calls
again kmem_cache_destroy().
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0c0efbacab8d70700d13301e0ae7975783c0cb0a upstream.
handle_ir_buffer_fill() assumed that a completed descriptor would be
indicated by a non-zero transfer_status (as in most other descriptors).
However, this field is written by the controller as soon as (the end of)
the first packet has been written into the buffer. As a consequence, if
we happen to run into such a descriptor when the interrupt handler is
executed after such a packet has completed, the descriptor would be
taken out of the list of active descriptors as soon as the buffer had
been partially filled, so the event for the buffer being completely
filled would never be sent.
To fix this, handle descriptors only when they have been completely
filled, i.e., when res_count == 0. (This also matches the condition
that is reported by the controller with an interrupt.)
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9716387311c790de381214c03e7f1b72b91a8189 upstream.
According to the HT6560H datasheet, the recovery timing field is 4-bit wide,
with a value of 0 meaning 16 cycles. Correct obvious thinko in the recovery
field mask.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d408e2b14fba4fa214fa5bc24b7baae8a55e563c upstream.
Some platforms need to make use of the AHCI_HFLAG_DELAY_ENGINE flag.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 55d5ec316627b64c3764e4c1b4b8e1988e272c1f upstream.
We will need this macro in both ahci.c and ahci_platform.c, so just move it
to the header.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 66583c9fa63d05d5580e409f9a58d3cad6d76d17 upstream.
The following commit was intended to fix problems with specific AHCI
controller(s) that would become bricks if the AHCI specification was not
followed strictly (that is, if ahci_start_engine() was called while the
controller was in the wrong state):
commit 7faa33da9b7add01db9f1ad92c6a5d9145e940a7
ahci: start engine only during soft/hard resets
However, some devices currently have issues with that fix, so we must
implement a flag that delays the ahci_start_engine() call only for specific
controllers.
This commit simply introduces the flag, without enabling it in any driver.
Note that even when AHCI_HFLAG_DELAY_ENGINE is not enabled, this patch does
not constitue a full revert to commit 7faa33da; there is still a change in
behavior to the ahci_port_suspend() failure path.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6c30d5a53229aad22bb675e0bd6eb518ecaa4316 upstream.
Add support for the camera key. The hotkey for
Asus S.H.E(Super Hybrid Engine) mode is mapped to KEY_KEY_PROG1
just for notifying the userspace.
Signed-off-by: Keng-Yu Lin <kengyu@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3596bb929f2abd3433c2eaa5755fad48ac207af1 upstream.
The Asus All-In-One PC has a wireless keyboard with wifi toggle,
brightness up, brightness down and display off hotkeys.
This patch adds suppoort for these hotkeys.
Signed-off-by: Keng-Yu Lin <kengyu@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6b6ba88b5bb8779156b21bb957520a448c3642e2 upstream.
The ID is found on Asus K54HR and K53U.
Blacklist the AR3011-based device ID [0489:e03d]
and add to ath3k.c for firmware loading.
Below is the output of usb-devices script:
Before the fiwmware loading:
T: Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0489 ProdID=e03d Rev=00.01
C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
After the fiwmware loading:
T: Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 5 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0cf3 ProdID=3005 Rev=00.01
C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
Signed-off-by: Keng-Yu Lin <kengyu@canonical.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 33395fb8a13731c7ef7b175dbf5a4d8a6738fe6c upstream.
The old code did (MSB << 8) & 0xff, which always evaluates to 0. Just use
get_unaligned_be16() so we don't have to worry about whether our open-coded
version is correct or not.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 47f1b8803e1e358ebbf4f82bfdb98971c912a2c3 upstream.
transport_kmap_data_sg can return NULL. I never saw this trigger, but
returning -ENOMEM seems better than a crash. Also removes a pointless
case while at it.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 382436f8804fe1cb20b9a2a811a10eb2d8554721 upstream.
Fix possible NULL pointer dereference in target_report_luns failure path.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit effc6cc8828257c32c37635e737f14fd6e19ecd7 upstream.
SPC-4 says about the WBUS16 and SYNC bits:
The meanings of these fields are specific to SPI-5 (see 6.4.3).
For SCSI transport protocols other than the SCSI Parallel
Interface, these fields are reserved.
We don't have a SPI fabric module, so we should never set these bits.
(The comment was misleading, since it only mentioned Sync but the
actual code set WBUS16 too).
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 089461dda1770c10fea0b988ff74519a9be81d7e upstream.
Current code sets the peripheral device type to 0x3f == "not present
unknown" for virtual LUN 0 for standard INQUIRY commands, but leaves it
as 0 == "connected direct access block" for VPD INQUIRY commands. This
is just because the check for LUN 0 only happens in some code paths.
Make our peripheral device type consistent by moving the LUN 0 check
into the common emulate_inquiry() code.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
