aboutsummaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2010-06-23e1000e: disable gig speed when in S0->Sx transitionBruce Allan
Most of this workaround is necessary for all ICHx/PCH parts so one of the two MAC-type checks can be removed. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-23e1000e: packet split should not be used with early receiveBruce Allan
Originally it was thought there were issues with ICHx/PCH parts with packet split when jumbo frames were enabled but in fact it is really only when early-receive is enabled (via ERT register) on these parts. Use packet split with jumbos but only when early-receive is not enabled. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-23e1000e: do not touch PHY page 800 registers when link speed is 1000MbpsBruce Allan
The PHY on 82577/82578 has issues when the registers on page 800 are accessed when in gigabit mode. Do not clear the Wakeup Control register when resetting the part since it is on page 800 (and will be cleared on reset anyway). Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-23e1000e: avoid polling h/w registers during link negotiationBruce Allan
Avoid touching hardware registers when possible, otherwise link negotiation can get messed up when user-level scripts are rapidly polling the driver to see if/when link is up. Use the saved link state information instead when possible. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-20caif: Use link layer MTU instead of fixed MTUSjur Braendeland
Previously CAIF supported maximum transfer size of ~4050. The transfer size is now calculated dynamically based on the link layers mtu size. Signed-off-by: Sjur Braendeland@stericsson.com Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-18e1000e: update driver version numberBruce Allan
Also separate out an _EXTRAVERSION similar to the core kernel. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-18e1000e: update copyright informationBruce Allan
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-18e1000e: enable support for EEE on 82579Bruce Allan
This patch enables IEEE802.3az (a.k.a. Energy Efficient Ethernet) on the new 82579 LOMs. An optional module parameter is provided to disable the feature if desired. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-18e1000e: initial support for 82579 LOMsBruce Allan
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-18e1000e: fix check for manageability on ICHx/PCHBruce Allan
Do not check for all the bits in E1000_FWSM_MODE_MASK when checking for manageability on 82577/82578; only check if iAMT is enabled. Both of the manageability checks (for 82577/82578 and ICHx) must check the firmware valid bit too since the other bits are only valid when the latter is set. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-18e1000e: separate out PHY statistics register updatesBruce Allan
The 82577/82578 parts have half-duplex statistics in PHY registers. These need only be read when in half-duplex and should all be read at once rather than one at a time to prevent excessive cycles of acquiring/releasing the PHY semaphore. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-18e1000e: cleanup e1000_sw_lcd_config_ich8lan()Bruce Allan
Do not acquire and release the PHY unnecessarily for parts that return from this workaround without actually accessing the PHY registers. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-18e1000e: cleanup ethtool loopback setup codeBruce Allan
Refactor the loopback setup code to first handle the only 10/100 PHY supported by the driver if applicable and then handle the 1Gig PHYs in a switch statement for PHY-specific setups. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Emil Tantilov <emil.s.tantilov@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-18cxgb4: minor cleanupDimitris Michailidis
Remove an unused flag and replace couple constants with enums. Signed-off-by: Dimitris Michailidis <dm@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-18cxgb4: update FW definitionsDimitris Michailidis
Update to latest FW API. Most changes here pertain to port types and querying FW for parameter values. Signed-off-by: Dimitris Michailidis <dm@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-18cxgb4: add a missing error interruptDimitris Michailidis
Signed-off-by: Dimitris Michailidis <dm@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-18cxgb4: propagate link initialization errors to .ndo_open's callersDimitris Michailidis
Signed-off-by: Dimitris Michailidis <dm@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-18cxgb4: switch to 64 bit inteface statisticsDimitris Michailidis
Implement ndo_get_stats64, remove ndo_get_stats. Signed-off-by: Dimitris Michailidis <dm@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-18cxgb4: set dev_id to the port numberDimitris Michailidis
Signed-off-by: Dimitris Michailidis <dm@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-18cxgb4: implement EEHDimitris Michailidis
Implement the pci_error_handlers methods for EEH. Signed-off-by: Dimitris Michailidis <dm@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-18cxgb4: rearrange initialization code in preparation for EEHDimitris Michailidis
Split some existing initialization code into a separate function for use by EEH next. No functional changes. Signed-off-by: Dimitris Michailidis <dm@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-18cxgb4: dynamically determine flash size and FW image locationDimitris Michailidis
Handle the larger flash memories on newer boards: - get the size and number of sectors by probing the flash - writes and erases can take longer, adjust the timeouts for these operations - the FW image can be at different locations depending on flash size, find its location dynamically as well. Signed-off-by: Dimitris Michailidis <dm@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-17Merge branch 'master' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6
2010-06-17Merge branch 'master' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6 Conflicts: net/mac80211/mlme.c
2010-06-17qlcnic: fix register accessAmit Kumar Salecha
For certain set of register, base window addresses are not defined. In such cases window should not set. Return with error for such cases to avoid NMI. Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-17qlcnic: fix race in tx stop queueRajesh K Borundia
There is a race between netif_stop_queue and netif_stopped_queue check. So check once again if buffers are available to avoid race. With above logic we can also get rid of tx lock in process_cmd_ring. Signed-off-by: Rajesh K Borundia <rajesh.borundia@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-17qlcnic: seperate interrupt for TXschacko
Earlier all poll routine can process rx and tx, But now one poll routine to process rx + tx and other for rx only. Last msix vector will be used for separate tx interrupt. o This is supported from fw version 4.4.2. o Bump version 5.0.5 Signed-off-by: Sony Chacko <schacko@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-17qlcnic: change driver descriptionSritej Velaga
o Remove extra printing of mac address o This driver also supports NIC only Qlogic adapters. Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-17qlcnic: fix device soft resetSucheta Chakraborty
During device soft reset, don't halt every device block. Access to some blocks is required during recovery. Signed-off-by: Sucheta Chakraborty <sucheta@dut4145.unminc.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-16be2net: enable ipv6 tso supportAjit Khaparde
Add ipv6 support to the be2net driver. Signed-off-by: Ajit Khaparde <ajitk@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-16qlcnic: Bumped up version numberAnirban Chakraborty
Changed the driver version number to 5.0.4 Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-16qlcnic: Fix a bug in setting up NIC partitioning modeAnirban Chakraborty
The driver was not detecting the presence of NIC partitioning capability of the firmware properly. Now, it checks the eswitch set bit in the FW capabilities register and accordingly sets the driver mode as NPAR capable or not. Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-16ath5k: report PHY error frames only for chips which need itBruno Randolf
Only report PHY error frames for ANI on chipsets which do not have PHY error counters in hardware. Signed-off-by: Bruno Randolf <br1@einfach.org> Acked-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-16ath5k: review RX descriptor functionsBruno Randolf
Reviewed RX descriptor functions against the HAL sources. Some minor changes: - check size before making changes to the descriptor - whitespace - add comments about 5210 timestamps. this needs to be adressed later! - FIFO overrun error only available on 5210 - rs_phyerr should not be OR'ed - clear the whole ath5k_rx_status structure before using, instead of zeroing specific fields. Signed-off-by: Bruno Randolf <br1@einfach.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-16ath5k: take descriptor differences between 5210 and 5211 into accountBruno Randolf
There are some differences between 5210 and 5211 descriptors which we did not take into account before. Signed-off-by: Bruno Randolf <br1@einfach.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-16ath5k: update 5210/5211 frame typesBruno Randolf
Update 5210 frame types to match the HAL. We have to apply the same bitshift to the constants as we use later. Add 5211 specific frame types. Signed-off-by: Bruno Randolf <br1@einfach.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-16ath5k: review and add comments for descriptorsBruno Randolf
I carefully reviewed desh.h against the HAL sources. Added comments and made differences between 5210, 5211 and 5212 more clear by adding _521x to the defines which are specific to that chipset. Renamed some defines. No functional changes. Signed-off-by: Bruno Randolf <br1@einfach.org> Acked-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-16ath5k: remove pointless rx error overlay structBruno Randolf
ath5k_hw_rx_error was only used once, where we could easily just use ath5k_hw_rx_status as well, so remove it. Signed-off-by: Bruno Randolf <br1@einfach.org> Acked-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-16ath5k: cosmetic changes in ath5k_hw_proc_5212_rx_status()Bruno Randolf
Just whitespace and indentation. Signed-off-by: Bruno Randolf <br1@einfach.org> Acked-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-16ath5k: use direct function calls for descriptors when possibleBruno Randolf
Use direct function calls for ath5k_hw_setup_rx_desc() and ath5k_hw_setup_mrr_tx_desc() instead of a function pointer which always pointed to the same function in the case of ath5k_hw_setup_rx_desc() and which is easily unified in the case of ath5k_hw_setup_mrr_tx_desc(). Also simplify the initialization function for the remaining function pointers. Signed-off-by: Bruno Randolf <br1@einfach.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-16ath5k: move checks and stats into new functionBruno Randolf
Create a new function ath5k_receive_frame_ok() which checks for errors, updates error statistics and tells us if we want to further "receive" this frame or not. This way we can avoid a goto and have a cleaner separation between buffer handling and other things. Signed-off-by: Bruno Randolf <br1@einfach.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-16ath5k: split descriptor handling and frame receiveBruno Randolf
Move frame reception into it's own function to have a clearer separation between buffer and descriptor handling and things that are done when we actually receive a frame. Signed-off-by: Bruno Randolf <br1@einfach.org> Acked-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-16ath5k: unify rx descriptor error handlingBruno Randolf
There is no reason for a special handling (return) here, just break like we do with the checks before. Signed-off-by: Bruno Randolf <br1@einfach.org> Acked-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-16ath5k: reset more pointers after we free skbsBruno Randolf
After we free skbs for receive or transmit descriptors, make sure we have no pointers to the now invalid memory address. Signed-off-by: Bruno Randolf <br1@einfach.org> Acked-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-16ath5k: print more errors when decriptor setup failsBruno Randolf
Signed-off-by: Bruno Randolf <br1@einfach.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-16ath5k: fix rx descriptor debuggingBruno Randolf
In the debug ouptut rx_status_0 was printed twice instead of rx_status_1. Also make the debug message more clear. Signed-off-by: Bruno Randolf <br1@einfach.org> Acked-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-16ath5k: fix some comment typosBruno Randolf
Fix comment about dma sizes, brackets were missing. Replace 'insure' with 'ensure'. Signed-off-by: Bruno Randolf <br1@einfach.org> Acked-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-16ath5k: rename ath5k_txbuf_free() to ath5k_txbuf_free_skb()Bruno Randolf
Rename ath5k_txbuf_free() to ath5k_txbuf_free_skb() since this is what it does: it frees the skb and not the buf. Same for ath5k_rxbuf_free(). Signed-off-by: Bruno Randolf <br1@einfach.org> Acked-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-16ath5k: more debug prints for resetsBruno Randolf
Add a debug print for every case of reset. Signed-off-by: Bruno Randolf <br1@einfach.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-16ipw2200: Enable LED by defaultubuntu@tjworld.net
BugLink: http://bugs.launchpad.net/bugs/21367 Enable LED by default and update the MODULE_PARM_DESC. The original reason for defaulting to disabled was documented in 2005 and noted, "The LED code has been reported to hang some systems when running ifconfig and is therefore disabled by default." This no longer appears applicable and users have been requesting this be enabled for several years. Signed-off-by: TJ <ubuntu@tjworld.net> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Andy Whitcroft <apw@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Leann Ogasawara <leann.ogasawara@canonical.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
generated by cgit v1.2.3-18-g5258 (git 2.32.0) at 2024-12-23 10:43:43 +0000