| Age | Commit message (Collapse) | Author |
|---|
|
commit 71f6d1b31fb1f278a345a30a2180515adc7d80ae upstream.
Right now the mvneta driver doesn't handle Tx IRQ, and relies on two
mechanisms to flush Tx descriptors : a flush at the end of mvneta_tx()
and a timer. If a burst of packets is emitted faster than the device
can send them, then the queue is stopped until next wake-up of the
timer 10ms later. This causes jerky output traffic with bursts and
pauses, making it difficult to reach line rate with very few streams.
A test on UDP traffic shows that it's not possible to go beyond 134
Mbps / 12 kpps of outgoing traffic with 1500-bytes IP packets. Routed
traffic tends to observe pauses as well if the traffic is bursty,
making it even burstier after the wake-up.
It seems that this feature was inherited from the original driver but
nothing there mentions any reason for not using the interrupt instead,
which the chip supports.
Thus, this patch enables Tx interrupts and removes the timer. It does
the two at once because it's not really possible to make the two
mechanisms coexist, so a split patch doesn't make sense.
First tests performed on a Mirabox (Armada 370) show that less CPU
seems to be used when sending traffic. One reason might be that we now
call the mvneta_tx_done_gbe() with a mask indicating which queues have
been done instead of looping over all of them.
The same UDP test above now happily reaches 987 Mbps / 87.7 kpps.
Single-stream TCP traffic can now more easily reach line rate. HTTP
transfers of 1 MB objects over a single connection went from 730 to
840 Mbps. It is even possible to go significantly higher (>900 Mbps)
by tweaking tcp_tso_win_divisor.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Arnaud Ebalard <arno@natisbad.org>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 40ba35e74fa56866918d2f3bc0528b5b92725d5e upstream.
Marvell has not published the chip's datasheet yet, so it's very hard
to find the relevant bits to manipulate to change the IRQ behaviour.
Fortunately, these bits are described in the proprietary LSP patch set
which is publicly available here :
http://www.plugcomputer.org/downloads/mirabox/
So let's put them back in the driver in order to reduce the burden of
current and future maintenance.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 290213667ab53a95456397763205e4b1e30f46b5 upstream.
If a queue timeout is reported, we can oops because of some
schedules while the caller is atomic, as shown below :
mvneta d0070000.ethernet eth0: tx timeout
BUG: scheduling while atomic: bash/1528/0x00000100
Modules linked in: slhttp_ethdiv(C) [last unloaded: slhttp_ethdiv]
CPU: 2 PID: 1528 Comm: bash Tainted: G WC 3.13.0-rc4-mvebu-nf #180
[<c0011bd9>] (unwind_backtrace+0x1/0x98) from [<c000f1ab>] (show_stack+0xb/0xc)
[<c000f1ab>] (show_stack+0xb/0xc) from [<c02ad323>] (dump_stack+0x4f/0x64)
[<c02ad323>] (dump_stack+0x4f/0x64) from [<c02abe67>] (__schedule_bug+0x37/0x4c)
[<c02abe67>] (__schedule_bug+0x37/0x4c) from [<c02ae261>] (__schedule+0x325/0x3ec)
[<c02ae261>] (__schedule+0x325/0x3ec) from [<c02adb97>] (schedule_timeout+0xb7/0x118)
[<c02adb97>] (schedule_timeout+0xb7/0x118) from [<c0020a67>] (msleep+0xf/0x14)
[<c0020a67>] (msleep+0xf/0x14) from [<c01dcbe5>] (mvneta_stop_dev+0x21/0x194)
[<c01dcbe5>] (mvneta_stop_dev+0x21/0x194) from [<c01dcfe9>] (mvneta_tx_timeout+0x19/0x24)
[<c01dcfe9>] (mvneta_tx_timeout+0x19/0x24) from [<c024afc7>] (dev_watchdog+0x18b/0x1c4)
[<c024afc7>] (dev_watchdog+0x18b/0x1c4) from [<c0020b53>] (call_timer_fn.isra.27+0x17/0x5c)
[<c0020b53>] (call_timer_fn.isra.27+0x17/0x5c) from [<c0020cad>] (run_timer_softirq+0x115/0x170)
[<c0020cad>] (run_timer_softirq+0x115/0x170) from [<c001ccb9>] (__do_softirq+0xbd/0x1a8)
[<c001ccb9>] (__do_softirq+0xbd/0x1a8) from [<c001cfad>] (irq_exit+0x61/0x98)
[<c001cfad>] (irq_exit+0x61/0x98) from [<c000d4bf>] (handle_IRQ+0x27/0x60)
[<c000d4bf>] (handle_IRQ+0x27/0x60) from [<c000843b>] (armada_370_xp_handle_irq+0x33/0xc8)
[<c000843b>] (armada_370_xp_handle_irq+0x33/0xc8) from [<c000fba9>] (__irq_usr+0x49/0x60)
Ben Hutchings attempted to propose a better fix consisting in using a
scheduled work for this, but while it fixed this panic, it caused other
random freezes and panics proving that the reset sequence in the driver
is unreliable and that additional fixes should be investigated.
When sending multiple streams over a link limited to 100 Mbps, Tx timeouts
happen from time to time, and the driver correctly recovers only when the
function is disabled.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 74c41b048db1073a04827d7f39e95ac1935524cc upstream.
Stats writers are mvneta_rx() and mvneta_tx(). They don't lock anything
when they update the stats, and as a result, it randomly happens that
the stats freeze on SMP if two updates happen during stats retrieval.
This is very easily reproducible by starting two HTTP servers and binding
each of them to a different CPU, then consulting /proc/net/dev in loops
during transfers, the interface should immediately lock up. This issue
also randomly happens upon link state changes during transfers, because
the stats are collected in this situation, but it takes more attempts to
reproduce it.
The comments in netdevice.h suggest using per_cpu stats instead to get
rid of this issue.
This patch implements this. It merges both rx_stats and tx_stats into
a single "stats" member with a single syncp. Both mvneta_rx() and
mvneta_rx() now only update the a single CPU's counters.
In turn, mvneta_get_stats64() does the summing by iterating over all CPUs
to get their respective stats.
With this change, stats are still correct and no more lockup is encountered.
Note that this bug was present since the first import of the mvneta
driver. It might make sense to backport it to some stable trees. If
so, it depends on "d33dc73 net: mvneta: increase the 64-bit rx/tx stats
out of the hot path".
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
[wt: port to 3.10 : u64_stats_init() does not exist in 3.10 and is not needed]
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dc4277dd41a80fd5f29a90412ea04bc3ba54fbf1 upstream.
Better count packets and bytes in the stack and on 32 bit then
accumulate them at the end for once. This saves two memory writes
and two memory barriers per packet. The incoming packet rate was
increased by 4.7% on the Openblocks AX3 thanks to this.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6cff1f6ad4c615319c1a146b2aa0af1043c5e9f5 upstream.
WARNING: CPU: 0 PID: 929 at /home/apw/COD/linux/kernel/irq/handle.c:147 handle_irq_event_percpu+0x1d1/0x1e0()
irq 17 handler device_intr+0x0/0xa80 [vt6655_stage] enabled interrupts
Using spin_lock_irqsave appears to fix this.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 61bd55ce1667809f022be88da77db17add90ea4e upstream.
When creating the demux table we need to iterate over the selected scan mask for
the buffer to get the samples which should be copied to destination buffer.
Right now the code uses the mask which contains all active channels, which means
the demux table contains entries which causes it to copy all the samples from
source to destination buffer one by one without doing any demuxing.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4aa0abed3a2a11b7d71ad560c1a3e7631c5a31cd upstream.
byReAssocCount is incremented every second resulting in
disassociated message being send every 10 seconds whether
connection or not.
byReAssocCount should only advance while eCommandState
is in WLAN_ASSOCIATE_WAIT
Change existing scope to if condition.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 89fb4cd1f717a871ef79fa7debbe840e3225cd54 upstream.
Flush commands don't transfer data and thus need to be special cased
in the I/O completion handler so that we can propagate errors to
the block layer and filesystem.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Reported-by: Steven Haber <steven@qumulo.com>
Tested-by: Steven Haber <steven@qumulo.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0193ed8225e1a79ed64632106ec3cc81798cb13c upstream.
This is a bug fix for the situation when function tsi721_desc_get() fails
to obtain a free transaction descriptor.
The bug usually results in a memory access crash dump when data transfer
scatter-gather list has more entries than size of hardware buffer
descriptors ring. This fix ensures that error is properly returned to a
caller instead of an invalid entry.
This patch is applicable to kernel versions starting from v3.5.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Andre van Herk <andre.van.herk@prodrive-technologies.com>
Cc: Stef van Os <stef.van.os@prodrive-technologies.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 043572d5444116b9d9ad8ae763cf069e7accbc30 upstream.
Temperature limit clamps are applied after converting the temperature
from milli-degrees C to degrees C, so either the clamp limit needs
to be specified in degrees C, not milli-degrees C, or clamping must
happen before converting to degrees C. Use the latter method to avoid
overflows.
vrm is an u8, so the written value needs to be limited to [0, 255].
Cc: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 50c5d36dab930b1f1b1e3348b8608aa8b9ee7610 upstream.
We attempt to remove noise from coordinates reported by devices in
input_handle_abs_event(), unfortunately, unless we were dropping the
event altogether, we were ignoring the adjusted value and were passing
on the original value instead.
Reviewed-by: Andrew de los Reyes <adlr@chromium.org>
Reviewed-by: Benson Leung <bleung@chromium.org>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b32bfc06aefab61acc872dec3222624e6cd867ed upstream.
Add support of the Promise FastTrak TX8660 SATA HBA in ahci mode by
registering the board in the ahci_pci_tbl[].
Note: this HBA also provide a hardware RAID mode when activated in
BIOS but specific drivers from the manufacturer are required in this
case.
Signed-off-by: Romain Degez <romain.degez@gmail.com>
Tested-by: Romain Degez <romain.degez@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1a112d10f03e83fb3a2fdc4c9165865dec8a3ca6 upstream.
1871ee134b73 ("libata: support the ata host which implements a queue
depth less than 32") directly used ata_port->scsi_host->can_queue from
ata_qc_new() to determine the number of tags supported by the host;
unfortunately, SAS controllers doing SATA don't initialize ->scsi_host
leading to the following oops.
BUG: unable to handle kernel NULL pointer dereference at 0000000000000058
IP: [<ffffffff814e0618>] ata_qc_new_init+0x188/0x1b0
PGD 0
Oops: 0002 [#1] SMP
Modules linked in: isci libsas scsi_transport_sas mgag200 drm_kms_helper ttm
CPU: 1 PID: 518 Comm: udevd Not tainted 3.16.0-rc6+ #62
Hardware name: Intel Corporation S2600CO/S2600CO, BIOS SE5C600.86B.02.02.0002.122320131210 12/23/2013
task: ffff880c1a00b280 ti: ffff88061a000000 task.ti: ffff88061a000000
RIP: 0010:[<ffffffff814e0618>] [<ffffffff814e0618>] ata_qc_new_init+0x188/0x1b0
RSP: 0018:ffff88061a003ae8 EFLAGS: 00010012
RAX: 0000000000000001 RBX: ffff88000241ca80 RCX: 00000000000000fa
RDX: 0000000000000020 RSI: 0000000000000020 RDI: ffff8806194aa298
RBP: ffff88061a003ae8 R08: ffff8806194a8000 R09: 0000000000000000
R10: 0000000000000000 R11: ffff88000241ca80 R12: ffff88061ad58200
R13: ffff8806194aa298 R14: ffffffff814e67a0 R15: ffff8806194a8000
FS: 00007f3ad7fe3840(0000) GS:ffff880627620000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000058 CR3: 000000061a118000 CR4: 00000000001407e0
Stack:
ffff88061a003b20 ffffffff814e96e1 ffff88000241ca80 ffff88061ad58200
ffff8800b6bf6000 ffff880c1c988000 ffff880619903850 ffff88061a003b68
ffffffffa0056ce1 ffff88061a003b48 0000000013d6e6f8 ffff88000241ca80
Call Trace:
[<ffffffff814e96e1>] ata_sas_queuecmd+0xa1/0x430
[<ffffffffa0056ce1>] sas_queuecommand+0x191/0x220 [libsas]
[<ffffffff8149afee>] scsi_dispatch_cmd+0x10e/0x300 [<ffffffff814a3bc5>] scsi_request_fn+0x2f5/0x550
[<ffffffff81317613>] __blk_run_queue+0x33/0x40
[<ffffffff8131781a>] queue_unplugged+0x2a/0x90
[<ffffffff8131ceb4>] blk_flush_plug_list+0x1b4/0x210
[<ffffffff8131d274>] blk_finish_plug+0x14/0x50
[<ffffffff8117eaa8>] __do_page_cache_readahead+0x198/0x1f0
[<ffffffff8117ee21>] force_page_cache_readahead+0x31/0x50
[<ffffffff8117ee7e>] page_cache_sync_readahead+0x3e/0x50
[<ffffffff81172ac6>] generic_file_read_iter+0x496/0x5a0
[<ffffffff81219897>] blkdev_read_iter+0x37/0x40
[<ffffffff811e307e>] new_sync_read+0x7e/0xb0
[<ffffffff811e3734>] vfs_read+0x94/0x170
[<ffffffff811e43c6>] SyS_read+0x46/0xb0
[<ffffffff811e33d1>] ? SyS_lseek+0x91/0xb0
[<ffffffff8171ee29>] system_call_fastpath+0x16/0x1b
Code: 00 00 00 88 50 29 83 7f 08 01 19 d2 83 e2 f0 83 ea 50 88 50 34 c6 81 1d 02 00 00 40 c6 81 17 02 00 00 00 5d c3 66 0f 1f 44 00 00 <89> 14 25 58 00 00 00
Fix it by introducing ata_host->n_tags which is initialized to
ATA_MAX_QUEUE - 1 in ata_host_init() for SAS controllers and set to
scsi_host_template->can_queue in ata_host_register() for !SAS ones.
As SAS hosts are never registered, this will give them the same
ATA_MAX_QUEUE - 1 as before. Note that we can't use
scsi_host->can_queue directly for SAS hosts anyway as they can go
higher than the libata maximum.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Mike Qiu <qiudayu@linux.vnet.ibm.com>
Reported-by: Jesse Brandeburg <jesse.brandeburg@gmail.com>
Reported-by: Peter Hurley <peter@hurleysoftware.com>
Reported-by: Peter Zijlstra <peterz@infradead.org>
Tested-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Fixes: 1871ee134b73 ("libata: support the ata host which implements a queue depth less than 32")
Cc: Kevin Hao <haokexin@gmail.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1871ee134b73fb4cadab75752a7152ed2813c751 upstream.
The sata on fsl mpc8315e is broken after the commit 8a4aeec8d2d6
("libata/ahci: accommodate tag ordered controllers"). The reason is
that the ata controller on this SoC only implement a queue depth of
16. When issuing the commands in tag order, all the commands in tag
16 ~ 31 are mapped to tag 0 unconditionally and then causes the sata
malfunction. It makes no senses to use a 32 queue in software while
the hardware has less queue depth. So consider the queue depth
implemented by the hardware when requesting a command tag.
Fixes: 8a4aeec8d2d6 ("libata/ahci: accommodate tag ordered controllers")
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit db4175ae2095634dbecd4c847da439f9c83e1b3b upstream.
Only supported modulation for DVB-S is QPSK. Modulation parameter
contains invalid value for DVB-S on some cases, which leads driver
refusing tuning attempt. Due to that, hard code modulation to QPSK
in case of DVB-S.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3445857b22eafb70a6ac258979e955b116bfd2c6 upstream.
When the audio encoding is changed the driver calls hdpvr_set_audio
with the current opt->audio_input value. However, that should have
been opt->audio_input + 1. So changing the audio encoding inadvertently
changes the input as well. This bug has always been there.
The second bug was introduced in kernel 3.10 and that broke the
default_audio_input module option handling: the audio encoding was
never switched to AC3 if default_audio_input was set to 2 (SPDIF input).
In addition, since starting with 3.10 the audio encoding is always set
at the start the first bug now always happens when the driver is loaded.
In the past this bug would only surface if the user would change the
audio encoding after the driver was loaded.
Also fixes a small trivial typo (bufffer -> buffer).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Scott Doty <scott@corp.sonic.net>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 048e5a07f282c57815b3901d4a68a77fa131ce0a upstream.
The block size for the dm-cache's data device must remained fixed for
the life of the cache. Disallow any attempt to change the cache's data
block size.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9aec8629ec829fc9403788cd959e05dd87988bd1 upstream.
The block size for the thin-pool's data device must remained fixed for
the life of the thin-pool. Disallow any attempt to change the
thin-pool's data block size.
It should be noted that attempting to change the data block size via
thin-pool table reload will be ignored as a side-effect of the thin-pool
handover that the thin-pool target does during thin-pool table reload.
Here is an example outcome of attempting to load a thin-pool table that
reduced the thin-pool's data block size from 1024K to 512K.
Before:
kernel: device-mapper: thin: 253:4: growing the data device from 204800 to 409600 blocks
After:
kernel: device-mapper: thin metadata: changing the data block size (from 2048 to 1024) is not supported
kernel: device-mapper: table: 253:4: thin-pool: Error creating metadata object
kernel: device-mapper: ioctl: error adding target to table
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0ac66effe7fcdee55bda6d5d10d3372c95a41920 upstream.
In some cases we fetch the edid in the detect() callback
in order to determine what sort of monitor is connected.
If that happens, don't fetch the edid again in the get_modes()
callback or we will leak the edid.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fbb60fe35ad579b511de8604b06a30b43846473b upstream.
Return IRQ_NONE if it was not our irq. This is necessary for the case
when qxl is sharing irq line with a device A in a crash kernel. If qxl
is initialized before A and A's irq was raised during this gap,
returning IRQ_HANDLED in this case will cause this irq to be raised
again after EOI since kernel think it was handled but in fact it was
not.
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 201bb62402e0227375c655446ea04fcd0acf7287 upstream.
If the value in the scratch register is 0, set it to the
max level. This fixes an issue where the console fb blanking
code calls back into the backlight driver on unblank and then
sets the backlight level to 0 after the driver has already
set the mode and enabled the backlight.
bugs:
https://bugs.freedesktop.org/show_bug.cgi?id=81382
https://bugs.freedesktop.org/show_bug.cgi?id=70207
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: David Heidelberger <david.heidelberger@ixit.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 29e697b11853d3f83b1864ae385abdad4aa2c361 upstream.
Certain GIC implementation, namely those found on earlier, single
cluster, Exynos SoCs, have registers mapped without per-CPU banking,
which means that the driver needs to use different offset for each CPU.
Currently the driver calculates the offset by multiplying value returned
by cpu_logical_map() by CPU offset parsed from DT. This is correct when
CPU topology is not specified in DT and aforementioned function returns
core ID alone. However when DT contains CPU topology, the function
changes to return cluster ID as well, which is non-zero on mentioned
SoCs and so breaks the calculation in GIC driver.
This patch fixes this by masking out cluster ID in CPU offset
calculation so that only core ID is considered. Multi-cluster Exynos
SoCs already have banked GIC implementations, so this simple fix should
be enough.
Reported-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reported-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Fixes: db0d4db22a78d ("ARM: gic: allow GIC to support non-banked setups")
Link: https://lkml.kernel.org/r/1405610624-18722-1-git-send-email-t.figa@samsung.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a97e8027b1d28eafe6bafe062556c1ec926a49c6 upstream.
Patch 0a68214b "ARM: DT: Add binding for GIC virtualization extentions (VGIC)" added
the "arm,cortex-a7-gic" compatible string, but the corresponding IRQCHIP_DECLARE
was never added to the gic driver.
To let real Cortex-A7 SoCs use it, add the necessary declaration to the device driver.
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lkml.kernel.org/r/1404388732-28890-1-git-send-email-matthias.bgg@gmail.com
Fixes: 0a68214b76ca ("ARM: DT: Add binding for GIC virtualization extentions (VGIC)")
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d76744a93246eccdca1106037e8ee29debf48277 upstream.
https://bugzilla.kernel.org/show_bug.cgi?id=70191
https://bugzilla.kernel.org/show_bug.cgi?id=77581
It is observed that sometimes Tx packet is downloaded without
adding driver's txpd header. This results in firmware parsing
garbage data as packet length. Sometimes firmware is unable
to read the packet if length comes out as invalid. This stops
further traffic and timeout occurs.
The root cause is uninitialized fields in tx_info(skb->cb) of
packet used to get garbage values. In this case if
MWIFIEX_BUF_FLAG_REQUEUED_PKT flag is mistakenly set, txpd
header was skipped. This patch makes sure that tx_info is
correctly initialized to fix the problem.
Reported-by: Andrew Wiley <wiley.andrew.j@gmail.com>
Reported-by: Linus Gasser <list@markas-al-nour.org>
Reported-by: Michael Hirsch <hirsch@teufel.de>
Tested-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Maithili Hinge <maithili@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a4b70a07ed12a71131cab7adce2ce91c71b37060 ]
Nothing cleans up the objects created by
vnet_new(), they are completely leaked.
vnet_exit(), after doing the vio_unregister_driver() to clean
up ports, should call a helper function that iterates over vnet_list
and cleans up those objects. This includes unregister_netdevice()
as well as free_netdev().
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Reviewed-by: Karl Volz <karl.volz@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a8a3e41c67d24eb12f9ab9680cbb85e24fcd9711 ]
The PPP channel MTU is used with Multilink PPP when ppp_mp_explode() (see
ppp_generic module) tries to determine how big a fragment might be. According
to RFC 1661, the MTU excludes the 2-byte PPP protocol field, see the
corresponding comment and code in ppp_mp_explode():
/*
* hdrlen includes the 2-byte PPP protocol field, but the
* MTU counts only the payload excluding the protocol field.
* (RFC1661 Section 2)
*/
mtu = pch->chan->mtu - (hdrlen - 2);
However, the pppoe module *does* include the PPP protocol field in the channel
MTU, which is wrong as it causes the PPP payload to be 1-2 bytes too big under
certain circumstances (one byte if PPP protocol compression is used, two
otherwise), causing the generated Ethernet packets to be dropped. So the pppoe
module has to subtract two bytes from the channel MTU. This error only
manifests itself when using Multilink PPP, as otherwise the channel MTU is not
used anywhere.
In the following, I will describe how to reproduce this bug. We configure two
pppd instances for multilink PPP over two PPPoE links, say eth2 and eth3, with
a MTU of 1492 bytes for each link and a MRRU of 2976 bytes. (This MRRU is
computed by adding the two link MTUs and subtracting the MP header twice, which
is 4 bytes long.) The necessary pppd statements on both sides are "multilink
mtu 1492 mru 1492 mrru 2976". On the client side, we additionally need "plugin
rp-pppoe.so eth2" and "plugin rp-pppoe.so eth3", respectively; on the server
side, we additionally need to start two pppoe-server instances to be able to
establish two PPPoE sessions, one over eth2 and one over eth3. We set the MTU
of the PPP network interface to the MRRU (2976) on both sides of the connection
in order to make use of the higher bandwidth. (If we didn't do that, IP
fragmentation would kick in, which we want to avoid.)
Now we send a ICMPv4 echo request with a payload of 2948 bytes from client to
server over the PPP link. This results in the following network packet:
2948 (echo payload)
+ 8 (ICMPv4 header)
+ 20 (IPv4 header)
---------------------
2976 (PPP payload)
These 2976 bytes do not exceed the MTU of the PPP network interface, so the
IP packet is not fragmented. Now the multilink PPP code in ppp_mp_explode()
prepends one protocol byte (0x21 for IPv4), making the packet one byte bigger
than the negotiated MRRU. So this packet would have to be divided in three
fragments. But this does not happen as each link MTU is assumed to be two bytes
larger. So this packet is diveded into two fragments only, one of size 1489 and
one of size 1488. Now we have for that bigger fragment:
1489 (PPP payload)
+ 4 (MP header)
+ 2 (PPP protocol field for the MP payload (0x3d))
+ 6 (PPPoE header)
--------------------------
1501 (Ethernet payload)
This packet exceeds the link MTU and is discarded.
If one configures the link MTU on the client side to 1501, one can see the
discarded Ethernet frames with tcpdump running on the client. A
ping -s 2948 -c 1 192.168.15.254
leads to the smaller fragment that is correctly received on the server side:
(tcpdump -vvvne -i eth3 pppoes and ppp proto 0x3d)
52:54:00:ad:87:fd > 52:54:00:79:5c:d0, ethertype PPPoE S (0x8864),
length 1514: PPPoE [ses 0x3] MLPPP (0x003d), length 1494: seq 0x000,
Flags [end], length 1492
and to the bigger fragment that is not received on the server side:
(tcpdump -vvvne -i eth2 pppoes and ppp proto 0x3d)
52:54:00:70:9e:89 > 52:54:00:5d:6f:b0, ethertype PPPoE S (0x8864),
length 1515: PPPoE [ses 0x5] MLPPP (0x003d), length 1495: seq 0x000,
Flags [begin], length 1493
With the patch below, we correctly obtain three fragments:
52:54:00:ad:87:fd > 52:54:00:79:5c:d0, ethertype PPPoE S (0x8864),
length 1514: PPPoE [ses 0x1] MLPPP (0x003d), length 1494: seq 0x000,
Flags [begin], length 1492
52:54:00:70:9e:89 > 52:54:00:5d:6f:b0, ethertype PPPoE S (0x8864),
length 1514: PPPoE [ses 0x1] MLPPP (0x003d), length 1494: seq 0x000,
Flags [none], length 1492
52:54:00:ad:87:fd > 52:54:00:79:5c:d0, ethertype PPPoE S (0x8864),
length 27: PPPoE [ses 0x1] MLPPP (0x003d), length 7: seq 0x000,
Flags [end], length 5
And the ICMPv4 echo request is successfully received at the server side:
IP (tos 0x0, ttl 64, id 21925, offset 0, flags [DF], proto ICMP (1),
length 2976)
192.168.222.2 > 192.168.15.254: ICMP echo request, id 30530, seq 0,
length 2956
The bug was introduced in commit c9aa6895371b2a257401f59d3393c9f7ac5a8698
("[PPPOE]: Advertise PPPoE MTU") from the very beginning. This patch applies
to 3.10 upwards but the fix can be applied (with minor modifications) to
kernels as old as 2.6.32.
Signed-off-by: Christoph Schulz <develop@kristov.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 4cad9f3b61c7268fa89ab8096e23202300399b5d ]
On BE3, if the clear-interrupt bit of the EQ doorbell is not set the first
time it is armed, ocassionally we have observed that the EQ doesn't raise
anymore interrupts even if it is in armed state.
This patch fixes this by setting the clear-interrupt bit when EQs are
armed for the first time in be_open().
Signed-off-by: Suresh Reddy <Suresh.Reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 0a1985879437d14bda8c90d0dae3455c467d7642 ]
This commit fixes the command value generated for CSUM calculation
when running in big endian mode. The Ethernet protocol ID for IP was
being unconditionally byte-swapped in the layer 3 protocol check (with
swab16), which caused the mvneta driver to not function correctly in
big endian mode. This patch byte-swaps the ID conditionally with
htons.
Cc: <stable@vger.kernel.org> # v3.13+
Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 4d12bc63ab5e48c1d78fa13883cf6fefcea3afb1 ]
As reported by Maggie Mae Roxas, the mvneta driver doesn't behave
properly in 10 Mbit/s mode. This is due to a misconfiguration of the
MVNETA_GMAC_AUTONEG_CONFIG register: bit MVNETA_GMAC_CONFIG_MII_SPEED
must be set for a 100 Mbit/s speed, but cleared for a 10 Mbit/s speed,
which the driver was not properly doing. This commit adjusts that by
setting the MVNETA_GMAC_CONFIG_MII_SPEED bit only in 100 Mbit/s mode,
and relying on the fact that all the speed related bits of this
register are cleared at the beginning of the mvneta_adjust_link()
function.
This problem exists since c5aff18204da0 ("net: mvneta: driver for
Marvell Armada 370/XP network unit") which is the commit that
introduced the mvneta driver in the kernel.
Cc: <stable@vger.kernel.org> # v3.8+
Fixes: c5aff18204da0 ("net: mvneta: driver for Marvell Armada 370/XP network unit")
Reported-by: Maggie Mae Roxas <maggie.mae.roxas@gmail.com>
Cc: Maggie Mae Roxas <maggie.mae.roxas@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 5343330010a892b76a97fd93ad3c455a4a32a7fb ]
Add two device IDs found in an out-of-tree driver downloadable
from Netgear.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 8dcb4b1526747d8431f9895e153dd478c9d16186 ]
There's a new version of the Telewell 4G modem working with, but not
recognized by this driver.
Signed-off-by: Bernd Wachter <bernd.wachter@jolla.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 07b0f00964def8af9321cfd6c4a7e84f6362f728 ]
While it is legal to kfree(NULL), it is not wise to use :
put_page(virt_to_head_page(NULL))
BUG: unable to handle kernel paging request at ffffeba400000000
IP: [<ffffffffc01f5928>] virt_to_head_page+0x36/0x44 [bnx2x]
Reported-by: Michel Lespinasse <walken@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ariel Elior <ariel.elior@qlogic.com>
Fixes: d46d132cc021 ("bnx2x: use netdev_alloc_frag()")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 43d826ca5979927131685cc2092c7ce862cb91cd upstream.
We should always prefer to use full RTS protection. Using
CTS to self gives a meaningless improvement, but this flow
is much harder for the firmware which is likely to have
issues with it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 76252723e88681628a3dbb9c09c963e095476f73 upstream.
To properly re-initialize SR-IOV it is necessary to reset the device
even if it is already down. Not doing this may result in Tx unit hangs.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit de12d6f4b10b21854441f5242dcb29ea96181e58 upstream.
Temperature limit registers are signed. Limits therefore need
to be clamped to (-128, 127) degrees C and not to (0, 255)
degrees C.
Without this fix, writing a limit of 128 degrees C sets the
actual limit to -128 degrees C.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ee14b644daaa58afe1e91bb9ebd9cf1b18d1f5fa upstream.
Dashes are not allowed in hwmon name attributes.
Use "da9052" instead of "da9052-hwmon".
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6b00f440dd678d786389a7100a2e03fe44478431 upstream.
Dashes are not allowed in hwmon name attributes.
Use "da9055" instead of "da9055-hwmon".
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 48439d501e3d9e8634bdc0c418e066870039599d upstream.
When detecting a non-link packet, h5_reset_rx() frees the Rx skb.
Not returning after that will cause the upcoming h5_rx_payload()
call to dereference a now NULL Rx skb and trigger a kernel oops.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9bd2d0dfe4714dd5d7c09a93a5c9ea9e14ceb3fc upstream.
Add code to poll the channel since we process only one message
at a time and the host may not interrupt us. Also increase the
receive buffer size since some KVP messages are close to 8K bytes in size.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 242841d3d71191348f98310e2d2001e1001d8630 upstream.
Tested-and-reported-by: yullaw <yullaw@mageia.cz>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bb86cf569bbd7ad4dce581a37c7fbd748057e9dc upstream.
When using USB 3.0 pen drive with the [AMD] FCH USB XHCI Controller
[1022:7814], the second hotplugging will experience the USB 3.0 pen
drive is recognized as high-speed device. After bisecting the kernel,
I found the commit number 41e7e056cdc662f704fa9262e5c6e213b4ab45dd
(USB: Allow USB 3.0 ports to be disabled.) causes the bug. After doing
some experiments, the bug can be fixed by avoiding executing the function
hub_usb3_port_disable(). Because the port status with [AMD] FCH USB
XHCI Controlleris [1022:7814] is already in RxDetect
(I tried printing out the port status before setting to Disabled state),
it's reasonable to check the port status before really executing
hub_usb3_port_disable().
Fixes: 41e7e056cdc6 (USB: Allow USB 3.0 ports to be disabled.)
Signed-off-by: Gavin Guo <gavin.guo@canonical.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 75646e758a0ecbed5024454507d5be5b9ea9dcbf upstream.
Some machines (eg. Lenovo Z480) ECs are not stable during boot up
and causes battery driver fails to be loaded due to failure of getting
battery information from EC sometimes. After several retries, the
operation will work. This patch is to retry to get battery information 5
times if the first try fails.
[ backport to 3.14.5: removed second parameter in acpi_battery_update(),
introduced by the commit 9e50bc14a7f58b5d8a55973b2d69355852ae2dae (ACPI /
battery: Accelerate battery resume callback)]
[naszar <naszar@ya.ru>: backport to 3.14.5]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=75581
Reported-and-tested-by: naszar <naszar@ya.ru>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0986c1a55ca64b44ee126a2f719a6e9f28cbe0ed upstream.
When we set the valid bit on invalid GART entries they are
loaded into the TLB when an adjacent entry is loaded. This
poisons the TLB with invalid entries which are sometimes
not correctly removed on TLB flush.
For stable inclusion the patch probably needs to be modified a bit.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6abafb78f9881b4891baf74ab4e9f090ae45230e upstream.
Fixes hangs on driver load on some cards.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=76998
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 10f1d5d111e8aed46a0f1179faf9a3cf422f689e upstream.
There's a race condition between the atomic_dec_and_test(&io->count)
in dec_count() and the waking of the sync_io() thread. If the thread
is spuriously woken immediately after the decrement it may exit,
making the on stack io struct invalid, yet the dec_count could still
be using it.
Fix this race by using a completion in sync_io() and dec_count().
Reported-by: Minfei Huang <huangminfei@ucloud.cn>
Signed-off-by: Joe Thornber <thornber@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit affb1aff300ddee54df307812b38f166e8a865ef upstream.
Starting with Win8, we have implemented several optimizations to improve the
scalability and performance of the VMBUS transport between the Host and the
Guest. Some of the non-performance critical services cannot leverage these
optimization since they only read and process one message at a time.
Make adjustments to the callback dispatch code to account for the way
non-performance critical drivers handle reading of the channel.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 15ebb05248d025534773c9ef64915bd888f04e4b upstream.
The control register is at offset 0x10, not 0x0. This is wreckaged
since commit 5df33a62c (SPEAr: Switch to common clock framework).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5a90af67c2126fe1d04ebccc1f8177e6ca70d3a9 upstream.
Since commtit 8a7b1227e303 (cpufreq: davinci: move cpufreq driver to
drivers/cpufreq) this added dependancy only for CONFIG_ARCH_DAVINCI_DA850
where as davinci_cpufreq_init() call is used by all davinci platform.
This patch fixes following build error:
arch/arm/mach-davinci/built-in.o: In function `davinci_init_late':
:(.init.text+0x928): undefined reference to `davinci_cpufreq_init'
make: *** [vmlinux] Error 1
Fixes: 8a7b1227e303 (cpufreq: davinci: move cpufreq driver to drivers/cpufreq)
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 867f9d463b82462793ea4610e748be0b04b37fc7 upstream.
The recently merged c |
