| Age | Commit message (Collapse) | Author |
|---|
|
commit f76ccaac4f82c463a037aa4a1e4ccb85c7011814 upstream.
FCP device remains in status ERP_FAILED when device is switched online
or adapter recovery is triggered while link to SAN is down.
When Exchange Configuration Data command returns the FSF status
FSF_EXCHANGE_CONFIG_DATA_INCOMPLETE it aborts the exchange process.
The only retries are done during the common error recovery procedure
(i.e. max. 3 retries with 8sec sleep between) and remains in status
ERP_FAILED with QDIO down.
This commit reverts the commit 0df138476c8306478d6e726f044868b4bccf411c
(zfcp: Fix adapter activation on link down).
When FSF status FSF_EXCHANGE_CONFIG_DATA_INCOMPLETE is received the
adapter recovery will be finished without any retries. QDIO will be
up now and status changes such as LINK UP will be received now.
Signed-off-by: Daniel Hansel <daniel.hansel@linux.vnet.ibm.com>
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c5bebd829dd95602c15f8da8cc50fa938b5e0254 upstream.
One of the customer had reported that the set of raid logical arrays will
become unavailable (I/O offline) after a long hours of IO stress test. The OS
wouldn`t be accessible afterwards and require a hard reset.
This driver patch has a fix for race condition between the doorbell and the
circular buffer. The driver is modified to do an extra read after clearing the
doorbell in case there had been a completion posted during the small timing
window.
With this fix, we ran IO stress for ~13 days. There were no IO failures.
Signed-off-by: Mahesh Rajashekhara <Mahesh.Rajashekhara@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 66c28f97120e8a621afd5aa7a31c4b85c547d33d upstream.
SATA drives located behind a SAS controller would incorrectly receive
WRITE SAME commands. Tweak the heuristics so that:
- If REPORT SUPPORTED OPERATION CODES is provided we will use that to
choose between WRITE SAME(16), WRITE SAME(10) and disabled. This also
fixes an issue with the old code which would issue WRITE SAME(10)
despite the command not being whitelisted in REPORT SUPPORTED
OPERATION CODES.
- If REPORT SUPPORTED OPERATION CODES is not provided we will fall back
to WRITE SAME(10) unless the device has an ATA Information VPD page.
The assumption is that a SATL which is smart enough to implement
WRITE SAME would also provide REPORT SUPPORTED OPERATION CODES.
To facilitate the new heuristics scsi_report_opcode() has been modified
to so we can distinguish between "operation not supported" and "RSOC not
supported".
Reported-by: H. Peter Anvin <hpa@zytor.com>
Tested-by: Bernd Schubert <bernd.schubert@itwm.fraunhofer.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d3bcb7b24bbf09fde8405770e676fe0c11c79662 upstream.
ah->noise is maintained globally and not per-channel. This
is updated in the reset() routine after the NF history has been
filled for the *current channel*, just before switching to
the new channel. There is no need to do it inside getnf(), since
ah->noise must contain a value for the new channel.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 696df78509d1f81b651dd98ecdc1aecab616db6b upstream.
The commits,
"ath9k: Fix regression in channelwidth switch at the same channel"
"ath9k: Fix invalid noisefloor reading due to channel update"
attempted to fix noisefloor calibration when a channel switch
happens due to HT20/HT40 bandwidth change. This is causing invalid
readings resulting in messages like:
"ath: phy16: NF[0] (-45) > MAX (-95), correcting to MAX".
This results in an incorrect noise being used initially for reporting
the signal level of received packets, until NF calibration is done
and the history buffer is updated via the ANI timer, which happens
much later.
When a bandwidth change happens, it is appropriate to reset
the internal history data for the channel. Do this correctly in the
reset() routine by checking the "chanmode" variable.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 30d5b709da23f4ab9836c7f66d2d2e780a69cf12 upstream.
For AR9485 boards with XLNA, the default gpio config
is not set correctly, fix this.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0847beb2865f5ef1c8626ec1a37def18f3d6c41a upstream.
The code writes the default_power2 value into the TX field
of the RFCSR50 register, however the condition in the if
statement uses default_power1. Due to this, wrong TX power
value might be written into the register.
Use the correct value in the condition to fix the issue.
Compile tested only.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0a6f3a8ebaf13407523c2c7d575b4ca2debd23ba upstream.
The current code uses the same index value both
for the channel information array and for the TX
power table. The index starts from 14, however the
index of the TX power table must start from zero.
Fix it, in order to get the correct TX power value
for a given channel.
The changes in rt61pci.c and rt73usb.c are compile
tested only.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1a33bd2be705cbb3f57d7223b60baea441039307 upstream.
irq_of_parse_and_map() returns 0 on error, while the code checks for NO_IRQ.
This breaks on platforms that have NO_IRQ != 0.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7bb23c4934059c64cbee2e41d5d24ce122285176 upstream.
1/ When an different between blocks is found, data is copied from
one bio to the other. However bv_len is used as the length to
copy and this could be zero. So use r10_bio->sectors to calculate
length instead.
Using bv_len was probably always a bit dubious, but the introduction
of bio_advance made it much more likely to be a problem.
2/ When preparing some blocks for sync, we don't set BIO_UPTODATE
except on bios that we schedule for a read. This ensures that
missing/failed devices don't confuse the loop at the top of
sync_request write.
Commit 8be185f2c9d54d6 "raid10: Use bio_reset()"
removed a loop which set BIO_UPTDATE on all appropriate bios.
So we need to re-add that flag.
These bugs were introduced in 3.10, so this patch is suitable for
3.10-stable, and can remove a potential for data corruption.
Reported-by: Brassow Jonathan <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 78eaa0d4cbcdb345992fa3dd22b3bcbb473cc064 upstream.
1/ If a RAID10 is being reshaped to a fewer number of devices
and is stopped while this is ongoing, then when the array is
reassembled the 'mirrors' array will be allocated too small.
This will lead to an access error or memory corruption.
2/ A sanity test for a reshaping RAID10 array is restarted
is slightly incorrect.
Due to the first bug, this is suitable for any -stable
kernel since 3.5 where this code was introduced.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1376512065b23f39d5f9a160948f313397dde972 upstream.
The recent comment:
commit 7e83ccbecd608b971f340e951c9e84cd0343002f
md/raid10: Allow skipping recovery when clean arrays are assembled
Causes raid10 to skip a recovery in certain cases where it is safe to
do so. Unfortunately it also causes a reshape to be skipped which is
never safe. The result is that an attempt to reshape a RAID10 will
appear to complete instantly, but no data will have been moves so the
array will now contain garbage.
(If nothing is written, you can recovery by simple performing the
reverse reshape which will also complete instantly).
Bug was introduced in 3.10, so this is suitable for 3.10-stable.
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: Martin Wilck <mwilck@arcor.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b996ac90f595dda271cbd858b136b45557fc1a57 upstream.
To add AMD CZ SMBus controller device ID.
[bhelgaas: drop pci_ids.h update]
Signed-off-by: Shane Huang <shane.huang@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ddfef5de3d716f77bad32dbbba6b280158dfd721 upstream.
Increase the retry count for the hard reset function to 100 but
shorten the time out period to 500 ms. See the comment for
ahci_highbank_hardreset for the reasons why those vaulues were
chosen.
Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c7e8695bfa0611b39493a9dfe8bab9f63f9809bd upstream.
This patch adds the IDE-mode SATA DeviceIDs for the Intel Coleto Creek PCH.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7a87718d92760fc688628ad6a430643dafa16f1f upstream.
For some reason, a lot of port-multipliers have issues with softreset.
SIMG [34]7x series port-multipliers have been quite erratic in this
regard. I recall that it was better with some firmware revisions and
the current list of quirks worked fine for a while. I think it got
worse with later firmwares or maybe my test coverage wasn't good
enough. Anyways, HPA is reporting that his 3726 setup suffers SRST
failures and then the PMP gets confused and fails to probe the last
port.
The hope was that we try to stick to the standard as much as possible
and soonish the PMPs and their firmwares will improve in quality, so
the quirk list was kept to minimum. Well, it seems like that's never
gonna happen.
Let's set NO_SRST for all [34]7x PMPs so that whatever remaining
userbase of the device suffer the least. Maybe we should do the same
for 57xx's but unfortunately I don't have any device left to test and
I'm not even sure 57xx's have ever been made widely available, so
let's leave those alone for now.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d0887c43f51c308b01605346e55d906ba858a6f9 upstream.
There are some SATA controllers which have both devices 0 and 1 but this module
just zeroes out taskfile and sets then ATA_TFLAG_DEVICE (not sure that's needed)
which could lead to a wrong device being selected just before issuing command.
Thus we should call ata_tf_init() which sets up the device register value
properly, like all other users of ata_exec_internal() do...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 41fa9a944fce1d7efd5ee3d50ac85b92f42dcc3d upstream.
NCT6775 does not support alarms for fans 4 and 5. Drop the attributes.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b1d2bff6a61140454b9d203519cc686a2e9ef32f upstream.
Driver displays wrong alarms for temperature attributes.
Turns out that temperature alarm bits are not fixed, but determined
by temperature source mapping. To fix the problem, walk through
the temperature sources to determine the correct alarm bit associated
with a given attribute.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f91d1b63a4e096d3023aaaafec9d9d3aff25997f upstream.
When reading IIO_CHAN_INFO_OFFSET, the return value of iio_channel_read() for
success will be IIO_VAL*, checking for 0 is not correct.
Without this fix the offset applied by iio drivers will be ignored when
converting a raw value to one in appropriate base units (e.g mV) in
a IIO client drivers that use iio_convert_raw_to_processed including
iio-hwmon.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e8d05276f236ee6435e78411f62be9714e0b9377 upstream.
commit 2f7021a8 "cpufreq: protect 'policy->cpus' from offlining
during __gov_queue_work()" caused a regression in CPU hotplug,
because it lead to a deadlock between cpufreq governor worker thread
and the CPU hotplug writer task.
Lockdep splat corresponding to this deadlock is shown below:
[ 60.277396] ======================================================
[ 60.277400] [ INFO: possible circular locking dependency detected ]
[ 60.277407] 3.10.0-rc7-dbg-01385-g241fd04-dirty #1744 Not tainted
[ 60.277411] -------------------------------------------------------
[ 60.277417] bash/2225 is trying to acquire lock:
[ 60.277422] ((&(&j_cdbs->work)->work)){+.+...}, at: [<ffffffff810621b5>] flush_work+0x5/0x280
[ 60.277444] but task is already holding lock:
[ 60.277449] (cpu_hotplug.lock){+.+.+.}, at: [<ffffffff81042d8b>] cpu_hotplug_begin+0x2b/0x60
[ 60.277465] which lock already depends on the new lock.
[ 60.277472] the existing dependency chain (in reverse order) is:
[ 60.277477] -> #2 (cpu_hotplug.lock){+.+.+.}:
[ 60.277490] [<ffffffff810ac6d4>] lock_acquire+0xa4/0x200
[ 60.277503] [<ffffffff815b6157>] mutex_lock_nested+0x67/0x410
[ 60.277514] [<ffffffff81042cbc>] get_online_cpus+0x3c/0x60
[ 60.277522] [<ffffffff814b842a>] gov_queue_work+0x2a/0xb0
[ 60.277532] [<ffffffff814b7891>] cs_dbs_timer+0xc1/0xe0
[ 60.277543] [<ffffffff8106302d>] process_one_work+0x1cd/0x6a0
[ 60.277552] [<ffffffff81063d31>] worker_thread+0x121/0x3a0
[ 60.277560] [<ffffffff8106ae2b>] kthread+0xdb/0xe0
[ 60.277569] [<ffffffff815bb96c>] ret_from_fork+0x7c/0xb0
[ 60.277580] -> #1 (&j_cdbs->timer_mutex){+.+...}:
[ 60.277592] [<ffffffff810ac6d4>] lock_acquire+0xa4/0x200
[ 60.277600] [<ffffffff815b6157>] mutex_lock_nested+0x67/0x410
[ 60.277608] [<ffffffff814b785d>] cs_dbs_timer+0x8d/0xe0
[ 60.277616] [<ffffffff8106302d>] process_one_work+0x1cd/0x6a0
[ 60.277624] [<ffffffff81063d31>] worker_thread+0x121/0x3a0
[ 60.277633] [<ffffffff8106ae2b>] kthread+0xdb/0xe0
[ 60.277640] [<ffffffff815bb96c>] ret_from_fork+0x7c/0xb0
[ 60.277649] -> #0 ((&(&j_cdbs->work)->work)){+.+...}:
[ 60.277661] [<ffffffff810ab826>] __lock_acquire+0x1766/0x1d30
[ 60.277669] [<ffffffff810ac6d4>] lock_acquire+0xa4/0x200
[ 60.277677] [<ffffffff810621ed>] flush_work+0x3d/0x280
[ 60.277685] [<ffffffff81062d8a>] __cancel_work_timer+0x8a/0x120
[ 60.277693] [<ffffffff81062e53>] cancel_delayed_work_sync+0x13/0x20
[ 60.277701] [<ffffffff814b89d9>] cpufreq_governor_dbs+0x529/0x6f0
[ 60.277709] [<ffffffff814b76a7>] cs_cpufreq_governor_dbs+0x17/0x20
[ 60.277719] [<ffffffff814b5df8>] __cpufreq_governor+0x48/0x100
[ 60.277728] [<ffffffff814b6b80>] __cpufreq_remove_dev.isra.14+0x80/0x3c0
[ 60.277737] [<ffffffff815adc0d>] cpufreq_cpu_callback+0x38/0x4c
[ 60.277747] [<ffffffff81071a4d>] notifier_call_chain+0x5d/0x110
[ 60.277759] [<ffffffff81071b0e>] __raw_notifier_call_chain+0xe/0x10
[ 60.277768] [<ffffffff815a0a68>] _cpu_down+0x88/0x330
[ 60.277779] [<ffffffff815a0d46>] cpu_down+0x36/0x50
[ 60.277788] [<ffffffff815a2748>] store_online+0x98/0xd0
[ 60.277796] [<ffffffff81452a28>] dev_attr_store+0x18/0x30
[ 60.277806] [<ffffffff811d9edb>] sysfs_write_file+0xdb/0x150
[ 60.277818] [<ffffffff8116806d>] vfs_write+0xbd/0x1f0
[ 60.277826] [<ffffffff811686fc>] SyS_write+0x4c/0xa0
[ 60.277834] [<ffffffff815bbbbe>] tracesys+0xd0/0xd5
[ 60.277842] other info that might help us debug this:
[ 60.277848] Chain exists of:
(&(&j_cdbs->work)->work) --> &j_cdbs->timer_mutex --> cpu_hotplug.lock
[ 60.277864] Possible unsafe locking scenario:
[ 60.277869] CPU0 CPU1
[ 60.277873] ---- ----
[ 60.277877] lock(cpu_hotplug.lock);
[ 60.277885] lock(&j_cdbs->timer_mutex);
[ 60.277892] lock(cpu_hotplug.lock);
[ 60.277900] lock((&(&j_cdbs->work)->work));
[ 60.277907] *** DEADLOCK ***
[ 60.277915] 6 locks held by bash/2225:
[ 60.277919] #0: (sb_writers#6){.+.+.+}, at: [<ffffffff81168173>] vfs_write+0x1c3/0x1f0
[ 60.277937] #1: (&buffer->mutex){+.+.+.}, at: [<ffffffff811d9e3c>] sysfs_write_file+0x3c/0x150
[ 60.277954] #2: (s_active#61){.+.+.+}, at: [<ffffffff811d9ec3>] sysfs_write_file+0xc3/0x150
[ 60.277972] #3: (x86_cpu_hotplug_driver_mutex){+.+...}, at: [<ffffffff81024cf7>] cpu_hotplug_driver_lock+0x17/0x20
[ 60.277990] #4: (cpu_add_remove_lock){+.+.+.}, at: [<ffffffff815a0d32>] cpu_down+0x22/0x50
[ 60.278007] #5: (cpu_hotplug.lock){+.+.+.}, at: [<ffffffff81042d8b>] cpu_hotplug_begin+0x2b/0x60
[ 60.278023] stack backtrace:
[ 60.278031] CPU: 3 PID: 2225 Comm: bash Not tainted 3.10.0-rc7-dbg-01385-g241fd04-dirty #1744
[ 60.278037] Hardware name: Acer Aspire 5741G /Aspire 5741G , BIOS V1.20 02/08/2011
[ 60.278042] ffffffff8204e110 ffff88014df6b9f8 ffffffff815b3d90 ffff88014df6ba38
[ 60.278055] ffffffff815b0a8d ffff880150ed3f60 ffff880150ed4770 3871c4002c8980b2
[ 60.278068] ffff880150ed4748 ffff880150ed4770 ffff880150ed3f60 ffff88014df6bb00
[ 60.278081] Call Trace:
[ 60.278091] [<ffffffff815b3d90>] dump_stack+0x19/0x1b
[ 60.278101] [<ffffffff815b0a8d>] print_circular_bug+0x2b6/0x2c5
[ 60.278111] [<ffffffff810ab826>] __lock_acquire+0x1766/0x1d30
[ 60.278123] [<ffffffff81067e08>] ? __kernel_text_address+0x58/0x80
[ 60.278134] [<ffffffff810ac6d4>] lock_acquire+0xa4/0x200
[ 60.278142] [<ffffffff810621b5>] ? flush_work+0x5/0x280
[ 60.278151] [<ffffffff810621ed>] flush_work+0x3d/0x280
[ 60.278159] [<ffffffff810621b5>] ? flush_work+0x5/0x280
[ 60.278169] [<ffffffff810a9b14>] ? mark_held_locks+0x94/0x140
[ 60.278178] [<ffffffff81062d77>] ? __cancel_work_timer+0x77/0x120
[ 60.278188] [<ffffffff810a9cbd>] ? trace_hardirqs_on_caller+0xfd/0x1c0
[ 60.278196] [<ffffffff81062d8a>] __cancel_work_timer+0x8a/0x120
[ 60.278206] [<ffffffff81062e53>] cancel_delayed_work_sync+0x13/0x20
[ 60.278214] [<ffffffff814b89d9>] cpufreq_governor_dbs+0x529/0x6f0
[ 60.278225] [<ffffffff814b76a7>] cs_cpufreq_governor_dbs+0x17/0x20
[ 60.278234] [<ffffffff814b5df8>] __cpufreq_governor+0x48/0x100
[ 60.278244] [<ffffffff814b6b80>] __cpufreq_remove_dev.isra.14+0x80/0x3c0
[ 60.278255] [<ffffffff815adc0d>] cpufreq_cpu_callback+0x38/0x4c
[ 60.278265] [<ffffffff81071a4d>] notifier_call_chain+0x5d/0x110
[ 60.278275] [<ffffffff81071b0e>] __raw_notifier_call_chain+0xe/0x10
[ 60.278284] [<ffffffff815a0a68>] _cpu_down+0x88/0x330
[ 60.278292] [<ffffffff81024cf7>] ? cpu_hotplug_driver_lock+0x17/0x20
[ 60.278302] [<ffffffff815a0d46>] cpu_down+0x36/0x50
[ 60.278311] [<ffffffff815a2748>] store_online+0x98/0xd0
[ 60.278320] [<ffffffff81452a28>] dev_attr_store+0x18/0x30
[ 60.278329] [<ffffffff811d9edb>] sysfs_write_file+0xdb/0x150
[ 60.278337] [<ffffffff8116806d>] vfs_write+0xbd/0x1f0
[ 60.278347] [<ffffffff81185950>] ? fget_light+0x320/0x4b0
[ 60.278355] [<ffffffff811686fc>] SyS_write+0x4c/0xa0
[ 60.278364] [<ffffffff815bbbbe>] tracesys+0xd0/0xd5
[ 60.280582] smpboot: CPU 1 is now offline
The intention of that commit was to avoid warnings during CPU
hotplug, which indicated that offline CPUs were getting IPIs from the
cpufreq governor's work items. But the real root-cause of that
problem was commit a66b2e5 (cpufreq: Preserve sysfs files across
suspend/resume) because it totally skipped all the cpufreq callbacks
during CPU hotplug in the suspend/resume path, and hence it never
actually shut down the cpufreq governor's worker threads during CPU
offline in the suspend/resume path.
Reflecting back, the reason why we never suspected that commit as the
root-cause earlier, was that the original issue was reported with
just the halt command and nobody had brought in suspend/resume to the
equation.
The reason for _that_ in turn, as it turns out, is that earlier
halt/shutdown was being done by disabling non-boot CPUs while tasks
were frozen, just like suspend/resume.... but commit cf7df378a
(reboot: migrate shutdown/reboot to boot cpu) which came somewhere
along that very same time changed that logic: shutdown/halt no longer
takes CPUs offline. Thus, the test-cases for reproducing the bug
were vastly different and thus we went totally off the trail.
Overall, it was one hell of a confusion with so many commits
affecting each other and also affecting the symptoms of the problems
in subtle ways. Finally, now since the original problematic commit
(a66b2e5) has been completely reverted, revert this intermediate fix
too (2f7021a8), to fix the CPU hotplug deadlock. Phew!
Reported-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Reported-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Tested-by: Peter Wu <lekensteyn@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit aae760ed21cd690fe8a6db9f3a177ad55d7e12ab upstream.
commit a66b2e (cpufreq: Preserve sysfs files across suspend/resume)
has unfortunately caused several things in the cpufreq subsystem to
break subtly after a suspend/resume cycle.
The intention of that patch was to retain the file permissions of the
cpufreq related sysfs files across suspend/resume. To achieve that,
the commit completely removed the calls to cpufreq_add_dev() and
__cpufreq_remove_dev() during suspend/resume transitions. But the
problem is that those functions do 2 kinds of things:
1. Low-level initialization/tear-down that are critical to the
correct functioning of cpufreq-core.
2. Kobject and sysfs related initialization/teardown.
Ideally we should have reorganized the code to cleanly separate these
two responsibilities, and skipped only the sysfs related parts during
suspend/resume. Since we skipped the entire callbacks instead (which
also included some CPU and cpufreq-specific critical components),
cpufreq subsystem started behaving erratically after suspend/resume.
So revert the commit to fix the regression. We'll revisit and address
the original goal of that commit separately, since it involves quite a
bit of careful code reorganization and appears to be non-trivial.
(While reverting the commit, note that another commit f51e1eb
(cpufreq: Fix cpufreq regression after suspend/resume) already
reverted part of the original set of changes. So revert only the
remaining ones).
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit da331ba8e9c5de72a27e50f71105395bba6eebe0 upstream.
tasklet_kill() may sleep so call it before taking pch->lock.
Fixes following lockup:
BUG: scheduling while atomic: cat/2383/0x00000002
Modules linked in:
unwind_backtrace+0x0/0xfc
__schedule_bug+0x4c/0x58
__schedule+0x690/0x6e0
sys_sched_yield+0x70/0x78
tasklet_kill+0x34/0x8c
pl330_free_chan_resources+0x24/0x88
dma_chan_put+0x4c/0x50
[...]
BUG: spinlock lockup suspected on CPU#0, swapper/0/0
lock: 0xe52aa04c, .magic: dead4ead, .owner: cat/2383, .owner_cpu: 1
unwind_backtrace+0x0/0xfc
do_raw_spin_lock+0x194/0x204
_raw_spin_lock_irqsave+0x20/0x28
pl330_tasklet+0x2c/0x5a8
tasklet_action+0xfc/0x114
__do_softirq+0xe4/0x19c
irq_exit+0x98/0x9c
handle_IPI+0x124/0x16c
gic_handle_irq+0x64/0x68
__irq_svc+0x40/0x70
cpuidle_wrap_enter+0x4c/0xa0
cpuidle_enter_state+0x18/0x68
cpuidle_idle_call+0xac/0xe0
cpu_idle+0xac/0xf0
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Cc: Vinod Koul <vinod.koul@linux.intel.com>
Cc: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 912b9ac683b112615d5605686f1dc086402ce9f7 upstream.
ata_link_online() check in ahci_error_intr() is unnecessary, it should
be removed otherwise may lead to lockup with FBS enabled PMP.
http://marc.info/?l=linux-ide&m=137050421603272&w=2
Reported-by: Yu Liu <liuyu.ac@gmail.com>
Signed-off-by: Shane Huang <shane.huang@amd.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1cfc7df3de10c40ed459e13cce6de616023bf41c upstream.
This patch adds the AHCI-mode SATA DeviceIDs for the Intel Coleto Creek PCH.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fafe5c3d82a470d73de53e6b08eb4e28d974d895 upstream.
To add AMD CZ SATA controller device ID of IDE mode.
[bhelgaas: drop pci_ids.h update]
Signed-off-by: Shane Huang <shane.huang@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8a487b1a7432b20ff3f82387a8ce7555a964b44e upstream.
When the queue is unmapped while it was so loaded that
mac80211's was stopped, we need to wake the queue after
having freed all the packets in the queue.
Not doing so can result in weird stuff like:
* run lots of traffic (mac80211's queue gets stopped)
* RFKILL
* de-assert RFKILL
* no traffic
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b967613d7e7c7bad176f5627c55e2d8c5aa2480e upstream.
When a queue is disabled, it frees all its entries. Later,
the op_mode might still get notifications from the firmware
that triggers to free entries in the tx queue. The transport
should be prepared for these races and know to ignore
reclaim calls on queues that have been disabled and whose
entries have been freed.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 343df771e671d821478dd3ef525a0610b808dbf8 upstream.
After calling device_register(&bridge->dev), the bridge is reference-
counted, and it is illegal to call kfree() on it except in the release
function.
[bhelgaas: changelog, use put_device() after device_register() failure]
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fbf33f516bdbcc2ab1ba1e54dfb720b0cfaa6874 upstream.
Commit 4f535093cf "PCI: Put pci_dev in device tree as early as possible"
moves device registering from pci_bus_add_devices() to pci_device_add().
That causes problems for virtual functions because device_add(&virtfn->dev)
is called before setting the virtfn->is_virtfn flag, which then causes Xen
to report PCI virtual functions as PCI physical functions.
Fix it by setting virtfn->is_virtfn before calling pci_device_add().
[Jiang Liu]: Move the setting of virtfn->is_virtfn ahead further for better
readability and modify changelog.
Signed-off-by: Xudong Hao <xudong.hao@intel.com>
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c378f70adbc1bbecd9e6db145019f14b2f688c7c upstream.
Currently, when a disconnect is requested by the user (via NBD_DISCONNECT
ioctl) the return from NBD_DO_IT is undefined (it is usually one of
several error codes). This means that nbd-client does not know if a
manual disconnect was performed or whether a network error occurred.
Because of this, nbd-client's persist mode (which tries to reconnect after
error, but not after manual disconnect) does not always work correctly.
This change fixes this by causing NBD_DO_IT to always return 0 if a user
requests a disconnect. This means that nbd-client can correctly either
persist the connection (if an error occurred) or disconnect (if the user
requested it).
Signed-off-by: Paul Clements <paul.clements@steeleye.com>
Acked-by: Rob Landley <rob@landley.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 148c1c8ad3c4170186ebe6ea5900adde27d2a0e7 upstream.
The June 2013 Macbook Air (13'') has a new trackpad protocol; four new
values are inserted in the header, and the mode switch is no longer
needed. This patch adds support for the new devices.
Reported-and-tested-by: Brad Ford <plymouthffl@gmail.com>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9d9a04ee758b4c1fcc7586d065cdde7a7607e156 upstream.
This patch adds keyboard support for MacbookAir6,2 as WELLSPRING8
(0x0291, 0x0292, 0x0293). The touchpad is handled in a separate
bcm5974 patch, as usual.
Reported-and-tested-by: Brad Ford <plymouthffl@gmail.com>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 91bdad0b6237c25a7bf8fd4604d0cc64a2005a23 upstream.
The role of acpi_bus_update_power() is to update the given ACPI
device object's power.state field to reflect the current physical
state of the device (as inferred from the configuration of power
resources and _PSC, if available). For this purpose it calls
acpi_device_set_power() that should update the power resources'
reference counters and set power.state as appropriate. However,
that doesn't work if the "new" state is D1, D2 or D3hot and the
the current value of power.state means D3cold, because in that
case acpi_device_set_power() will refuse to transition the device
from D3cold to non-D0.
To address this problem, make acpi_bus_update_power() call
acpi_power_transition() directly to update the power resources'
reference counters and only use acpi_device_set_power() to put
the device into D0 if the current physical state of it cannot
be determined.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7cec7048fe22e3e92389da2cd67098f6c4284e7f upstream.
Previous implementation incorrectly used the ACPI 5.0 extended
sleep registers if they were simply populated. This caused
problems on some non-HW-reduced machines. As per the ACPI spec,
they should only be used if the HW-reduced bit is set. Lv Zheng,
ACPICA BZ 1020.
Reported-by: Daniel Rowe <bart@fathom13.com>
References: https://bugzilla.kernel.org/show_bug.cgi?id=54181
References: https://bugs.acpica.org/show_bug.cgi?id=1020
Bisected-by: Brint E. Kriebel <kernel@bekit.net>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit eff9a4b62b14cf0d9913e3caf1f26f8b7a6105c9 upstream.
HP Folio 13's BIOS defines CMOS RTC Operation Region and the EC's
_REG method will access that region. To allow the CMOS RTC region
handler to be installed before the EC _REG method is first invoked,
add ec_skip_dsdt_scan() as HP Folio 13's callback to ec_dmi_table.
References: https://bugzilla.kernel.org/show_bug.cgi?id=54621
Reported-and-tested-by: Stefan Nagy <public@stefan-nagy.at>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2fa97feb4406c546b52e35b6b6c50cb8f63425d2 upstream.
On HP Folio 13-2000, the BIOS defines a CMOS RTC Operation Region and
the EC's _REG methord accesses that region. Thus an appropriate
address space handler must be registered for that region before the
EC driver is loaded.
Introduce a mechanism for adding CMOS RTC address space handlers.
Register an ACPI scan handler for CMOS RTC devices such that, when
a device of that kind is detected during an ACPI namespace scan, a
common CMOS RTC operation region address space handler will be
installed for it.
References: https://bugzilla.kernel.org/show_bug.cgi?id=54621
Reported-and-tested-by: Stefan Nagy <public@stefan-nagy.at>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 29ecd78c0fd6ee05f2c6b07b23823a6ae43c13ff upstream.
In the disable AIE irq code path, current code passes "1" to enable
parameter of rv3029c2_rtc_i2c_alarm_set_irq(). Thus it does not disable
AIE irq.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 098b1aeaf4d6149953b8f1f8d55c21d85536fbff upstream.
There are two tool-stack that can instruct the Xen PCI frontend
and backend to change states: 'xm' (Python code with a daemon),
and 'xl' (C library - does not keep state changes).
With the 'xm', the path to disconnect a single PCI device (xm pci-detach
<guest> <BDF>) is:
4(Connected)->7(Reconfiguring*)-> 8(Reconfigured)-> 4(Connected)->5(Closing*).
The * is for states that the tool-stack sets. For 'xl', it is similar:
4(Connected)->7(Reconfiguring*)-> 8(Reconfigured)-> 4(Connected)
Both of them also tear down the XenBus structure, so the backend
state ends up going in the 3(Initialised) and calls pcifront_xenbus_remove.
When a PCI device is plugged back in (xm pci-attach <guest> <BDF>)
both of them follow the same pattern:
2(InitWait*), 3(Initialized*), 4(Connected*)->4(Connected).
[xen-pcifront ignores the 2,3 state changes and only acts when
4 (Connected) has been reached]
Note that this is for a _single_ PCI device. If there were two
PCI devices and only one was disconnected 'xm' would show the same
state changes.
The problem is that git commit 3d925320e9e2de162bd138bf97816bda8c3f71be
("xen/pcifront: Use Xen-SWIOTLB when initting if required") introduced
a mechanism to initialize the SWIOTLB when the Xen PCI front moves to
Connected state. It also had some aggressive seatbelt code check that
would warn the user if one tried to change to Connected state without
hitting first the Closing state:
pcifront pci-0: PCI frontend already installed!
However, that code can be relaxed and we can continue on working
even if the frontend is instructed to be the 'Connected' state with
no devices and then gets tickled to be in 'Connected' state again.
In other words, this 4(Connected)->5(Closing)->4(Connected) state
was expected, while 4(Connected)->.... anything but 5(Closing)->4(Connected)
was not. This patch removes that aggressive check and allows
Xen pcifront to work with the 'xl' toolstack (for one or more
PCI devices) and with 'xm' toolstack (for more than two PCI
devices).
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-pci@vger.kernel.org
[v2: Added in the description about two PCI devices]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dac76f1be5beaea4af9afe85fb475c73de0b8731 upstream.
The LMMIO length reported by PAT and the length given by the LBA MASK
register are not consistent. This leads e.g. to a not-working ATI FireGL
card with the radeon DRM driver since the memory can't be mapped.
Fix this by correctly adjusting the resource sizes.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e39506b466edcda2a7e9d0174d7987ae654137b7 upstream.
Commit 80af9e6d (pcmcia at91_cf: fix raw gpio number usage) forgot
to change the parameter in gpio_get_value after adding gpio
validation.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 35848f68b07df3f917cb13fc3c134718669f569b upstream.
Even if guest were compiled without SMP support, it could not assume that host
wasn't. So switch to use mb() instead of smp_mb() to force memory barriers for
UP guest.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5388a3a5faba8dfa69e5f06c3a415d373c1a4316 upstream.
Do a release_mem_region of the hcd resource. Without this the
subsequent insertion of module fails in request_mem_region.
Signed-off-by: George Cherian <george.cherian@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 025f880cb2e4d7218d0422d4b07bea1a68959c38 upstream.
Fail and free the container context in case dma_pool_alloc() can't allocate
the raw context data part of it
This patch should be backported to kernels as old as 2.6.31, that
contain the commit d115b04818e57bdbc7ccde4d0660b15e33013dc8 "USB: xhci:
Support for 64-byte contexts".
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: John Youn <johnyoun@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4e5c9e6fa2d232a0686d5fe45cd1508484048936 upstream.
For PHY mode, the PHYs must be brought out of reset
before the EHCI controller is started.
This patch fixes the issue where USB devices are not found
on Beagleboard/Beagle-xm if USB has been started previously
by the bootloader. (e.g. by "usb start" command in u-boot)
Tested on Beagleboard, Beagleboard-xm and Pandaboard.
Issue present on 3.10 onwards.
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d68c277b501889b3a50c179d1c3d704db7947b83 upstream.
Without this memory barrier, the file-storage thread may fail to
escape from the following while loop, because it may observe new
common->thread_wakeup_needed and old bh->state which are updated by
the callback functions.
/* Wait for the CBW to arrive */
while (bh->state != BUF_STATE_FULL) {
rc = sleep_thread(common);
if (rc)
return rc;
}
Signed-off-by: UCHINO Satoshi <satoshi.uchino@toshiba.co.jp>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a254810a86aaaac4ac6ba44fa934558b042a17a7 upstream.
These devices are all Gobi1K devices (according to the Windows INF
files) and should be handled by qcserial instead of option. Their
network port is handled by qmi_wwan.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 29692d05647cb7ecea56242241f77291d5624b95 upstream.
Use DMI_BOARD_NAME to determine if we are running on a MinnowBoard and
set the uart clock to 50MHz if so. This removes the need to pass the
user_uartclk to the kernel at boot time.
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Peter Waskiewicz <peter.p.waskiewicz.jr@intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 10d0b9030a3f86e1e26c710c7580524d7787d688 upstream.
A typo causes routine rtl92cu_phy_rf6052_set_cck_txpower() to test the
same condition twice. The problem was found using cppcheck-1.49, and the
proper fix was verified against the pre-mac80211 version of the code.
This patch was originally included as commit 1288aa4, but was accidentally
reverted in a later patch.
Reported-by: David Binderman <dcb314@hotmail.com> [original report]
Reported-by: Andrea Morello <andrea.merello@gmail.com> [report of accidental reversion]
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
