| Age | Commit message (Collapse) | Author |
|---|
|
commit cbb330045e5df8f665ac60227ff898421fc8fb92 upstream.
This patch (as1465) continues implementation of the policy that errors
during suspend or hibernation should not prevent the system from going
to sleep.
In this case, failure to turn on the Suspend feature for a hub port
shouldn't be reported as an error. There are situations where this
does actually occur (such as when the device plugged into that port
was disconnected in the recent past), and it turns out to be harmless.
There's no reason for it to prevent a system sleep.
Also, don't allow the hub driver to fail a system suspend if the
downstream ports aren't all suspended. This is also harmless (and
should never happen, given the change mentioned above); printing a
warning message in the kernel log is all we really need to do.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 0af212ba8f123c2eba151af7726c34a50b127962 upstream.
This patch (as1464) implements the recommended policy that most errors
during suspend or hibernation should not prevent the system from going
to sleep. In particular, failure to suspend a USB driver or a USB
device should not prevent the sleep from succeeding:
Failure to suspend a device won't matter, because the device will
automatically go into suspend mode when the USB bus stops carrying
packets. (This might be less true for USB-3.0 devices, but let's not
worry about them now.)
Failure of a driver to suspend might lead to trouble later on when the
system wakes up, but it isn't sufficient reason to prevent the system
from going to sleep.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 6e4e2f811bade330126d4029c88c831784a7efd9 upstream.
Lockdep found a locking inconsistency in the mkiss_close function:
> kernel: [ INFO: inconsistent lock state ]
> kernel: 2.6.39.1 #3
> kernel: ---------------------------------
> kernel: inconsistent {IN-SOFTIRQ-R} -> {SOFTIRQ-ON-W} usage.
> kernel: ax25ipd/2813 [HC0[0]:SC0[0]:HE1:SE1] takes:
> kernel: (disc_data_lock){+++?.-}, at: [<ffffffffa018552b>] mkiss_close+0x1b/0x90 [mkiss]
> kernel: {IN-SOFTIRQ-R} state was registered at:
The message hints that disc_data_lock is aquired with softirqs disabled,
but does not itself disable softirqs, which can in rare circumstances
lead to a deadlock.
The same problem is present in the 6pack driver, this patch fixes both
by using write_lock_bh instead of write_lock.
Reported-by: Bernard F6BVP <f6bvp@free.fr>
Tested-by: Bernard F6BVP <f6bvp@free.fr>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ralf Baechle<ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 4274215d24633df7302069e51426659d4759c5ed upstream.
If a device fails in a way that causes pending request to take a while
to complete, md will not be able to immediately remove it from the
array in remove_and_add_spares.
It will then incorrectly look like a spare device and md will try to
recover it even though it is failed.
This leads to a recovery process starting and instantly aborting over
and over again.
We should check if the device is faulty before considering it to be a
spare. This will avoid trying to start a recovery that cannot
proceed.
This bug was introduced in 2.6.26 so that patch is suitable for any
kernel since then.
Reported-by: Jim Paradis <james.paradis@stratus.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 9b640f2e154268cb516efcaf9c434f2e73c6783e upstream.
* Print all error and information messages even when debugging is
disabled.
* Don't use adapter device to log messages before it is ready.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 9b19d40aa3ebaf1078779da10555da2ab8512422 upstream.
Otherwise, the gpiolib autorequest feature will produce a WARN_ON():
WARNING: at drivers/gpio/gpiolib.c:101 0x8020ec6c()
autorequest GPIO-215
[...]
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 8ca2c80b170c47eeb55f0c2a0f2b8edf85f35d49 upstream.
When freeing memory for the video buffers also remove them from the
irq & main queues.
This fixes an oops when doing the following:
open ("/dev/video", ..)
VIDIOC_REQBUFS
VIDIOC_QBUF
VIDIOC_REQBUFS
close ()
As the second VIDIOC_REQBUFS will cause the list entries of the buffers
to be cleared while they still hang around on the main and irc queues
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit a0b8de350be458b33248e48b2174d9af8a4c4798 upstream.
We would free the proper number of curves, but in the wrong
slots, due to a missing level of indirection through
the pdgain_idx table.
It's simpler just to try to free all four slots, so do that.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit fa75ac379e63c2864e9049b5e8615e40f65c1e70 upstream.
While trying to switch a UAS device from the BOT configuration to the UAS
configuration via the bConfigurationValue file, Tanya ran into an issue in
the USB core. usb_disable_device() sets entries in udev->ep_out and
udev->ep_out to NULL, but doesn't call into the xHCI bandwidth management
functions to remove the BOT configuration endpoints from the xHCI host's
internal structures.
The USB core would then attempt to add endpoints for the UAS
configuration, and some of the endpoints had the same address as endpoints
in the BOT configuration. The xHCI driver blindly added the endpoints
again, but the xHCI host controller rejected the Configure Endpoint
command because active endpoints were added without being dropped.
Make the xHCI driver reject calls to xhci_add_endpoint() that attempt to
add active endpoints without first calling xhci_drop_endpoint().
This should be backported to kernels as old as 2.6.31.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Tanya Brokhman <tlinder@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 92f6fa09bd453ffe3351fa1f1377a1b7cfa911e6 upstream.
We restored tty_ldisc_wait_idle in 100eeae2c5c (TTY: restore
tty_ldisc_wait_idle). We used it in the ldisc changing path to fix the
case where there are tasks in n_tty_read waiting for data and somebody
tries to change ldisc.
Similar to the case above, there may be also tasks waiting in
n_tty_read while hangup is performed. As 65b770468e98 (tty-ldisc: turn
ldisc user count into a proper refcount) removed the wait-until-idle
from all paths, hangup path won't wait for them to disappear either
now. So add it back even to the hangup path.
There is a difference, we need uninterruptible sleep as there is
obviously HUP signal pending. So tty_ldisc_wait_idle now sleeps
without possibility to be interrupted. This is what original
tty_ldisc_wait_idle did. After the wait idle reintroduction
(100eeae2c5c), we have had interruptible sleeps for the ldisc changing
path. But as there is a 5s timeout anyway, we don't allow it to be
interrupted from now on. It's not worth the added complexity of
deciding what kind of sleep we want.
Before 65b770468e98 tty_ldisc_release was called also from
tty_ldisc_release. It is called from tty_release, so I don't think we
need to restore that one.
This is nicely reproducible after constifying the timing when
drivers/tty/n_tty.c is patched as follows ("TTY: ntty, add one more
sanity check" patch is needed to actually see it explode):
%% -1548,6 +1549,7 @@ static int n_tty_open(struct tty_struct *tty)
/* These are ugly. Currently a malloc failure here can panic */
if (!tty->read_buf) {
+ msleep(100);
tty->read_buf = kzalloc(N_TTY_BUF_SIZE, GFP_KERNEL);
if (!tty->read_buf)
return -ENOMEM;
%% -1785,6 +1788,7 @@ do_it_again:
break;
}
timeout = schedule_timeout(timeout);
+ msleep(20);
continue;
}
__set_current_state(TASK_RUNNING);
===== With a process: =====
while (1) {
int fd = open(argv[1], O_RDWR);
read(fd, buf, sizeof(buf));
close(fd);
}
===== and its child: =====
setsid();
while (1) {
int fd = open(tty, O_RDWR|O_NOCTTY);
ioctl(fd, TIOCSCTTY, 1);
vhangup();
close(fd);
usleep(100 * (10 + random() % 1000));
}
===== EOF =====
References: https://bugzilla.novell.com/show_bug.cgi?id=693374
References: https://bugzilla.novell.com/show_bug.cgi?id=694509
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This reverts commit 6f63415fc1b690cb50c2ad48ba6e9e6e88e271b4.
It turns out this is not what we want to have happen for the .32 and
.33-longterm kernels as it does not work properly at all.
This was reported by Gentoo, Arch, and Canonical developers as causing
problems for their users:
https://bugs.archlinux.org/task/24302
http://bugs.gentoo.org/show_bug.cgi?id=359445
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/796336
Cc: Herton Ronaldo Krzesinski <herton.krzesinski@canonical.com>
Cc: Gordon Malm <gengor@gentoo.org>
Cc: Don Fry <donald.h.fry@intel.com>
Cc: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 676dc3cf5bc36a9e129a3ad8fe3bd7b2ebf20f5d upstream.
Mark the IRQF_NO_SUSPEND interrupts IRQF_FORCE_RESUME and remove the extra
walk through the interrupt descriptors.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 6903591f314b8947d0e362bda7715e90eb9df75e upstream.
The IRQ core code will take care of disabling and reenabling
interrupts over suspend resume automatically, therefore we do not need
to do this in the Xen event channel code.
The only exception is those event channels marked IRQF_NO_SUSPEND
which the IRQ core ignores. We must unmask these ourselves, taking
care to obey the current IRQ_DISABLED status. Failure check for
IRQ_DISABLED leads to enabling polled only event channels, such as
that associated with the pv spinlocks, which must never be enabled:
[ 21.970432] ------------[ cut here ]------------
[ 21.970432] kernel BUG at arch/x86/xen/spinlock.c:343!
[ 21.970432] invalid opcode: 0000 [#1] SMP
[ 21.970432] last sysfs file: /sys/devices/virtual/net/lo/operstate
[ 21.970432] Modules linked in:
[ 21.970432]
[ 21.970432] Pid: 0, comm: swapper Not tainted (2.6.32.24-x86_32p-xen-01034-g787c727 #34)
[ 21.970432] EIP: 0061:[<c102e209>] EFLAGS: 00010046 CPU: 3
[ 21.970432] EIP is at dummy_handler+0x3/0x7
[ 21.970432] EAX: 0000021c EBX: dfc16880 ECX: 0000001a EDX: 00000000
[ 21.970432] ESI: dfc02c00 EDI: 00000001 EBP: dfc47e10 ESP: dfc47e10
[ 21.970432] DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0069
[ 21.970432] Process swapper (pid: 0, ti=dfc46000 task=dfc39440 task.ti=dfc46000)
[ 21.970432] Stack:
[ 21.970432] dfc47e30 c10a39f0 0000021c 00000000 00000000 dfc16880 0000021c 00000001
[ 21.970432] <0> dfc47e40 c10a4f08 0000021c 00000000 dfc47e78 c12240a7 c1839284 c1839284
[ 21.970432] <0> 00000200 00000000 00000000 f5720000 c1f3d028 c1f3d02c 00000180 dfc47e90
[ 21.970432] Call Trace:
[ 21.970432] [<c10a39f0>] ? handle_IRQ_event+0x5f/0x122
[ 21.970432] [<c10a4f08>] ? handle_percpu_irq+0x2f/0x55
[ 21.970432] [<c12240a7>] ? __xen_evtchn_do_upcall+0xdb/0x15f
[ 21.970432] [<c122481e>] ? xen_evtchn_do_upcall+0x20/0x30
[ 21.970432] [<c1030d47>] ? xen_do_upcall+0x7/0xc
[ 21.970432] [<c102007b>] ? apic_reg_read+0xd3/0x22d
[ 21.970432] [<c1002227>] ? hypercall_page+0x227/0x1005
[ 21.970432] [<c102d30b>] ? xen_force_evtchn_callback+0xf/0x14
[ 21.970432] [<c102da7c>] ? check_events+0x8/0xc
[ 21.970432] [<c102da3b>] ? xen_irq_enable_direct_end+0x0/0x1
[ 21.970432] [<c105e485>] ? finish_task_switch+0x62/0xba
[ 21.970432] [<c14e3f84>] ? schedule+0x808/0x89d
[ 21.970432] [<c1084dc5>] ? hrtimer_start_expires+0x1a/0x22
[ 21.970432] [<c1085154>] ? tick_nohz_restart_sched_tick+0x15a/0x162
[ 21.970432] [<c102f43a>] ? cpu_idle+0x6d/0x6f
[ 21.970432] [<c14db29e>] ? cpu_bringup_and_idle+0xd/0xf
[ 21.970432] Code: 5d 0f 95 c0 0f b6 c0 c3 55 66 83 78 02 00 89 e5 5d 0f 95 \
c0 0f b6 c0 c3 55 b2 01 86 10 31 c0 84 d2 89 e5 0f 94 c0 5d c3 55 89 e5 <0f> 0b \
eb fe 55 80 3d 4c ce 84 c1 00 89 e5 57 56 89 c6 53 74 15
[ 21.970432] EIP: [<c102e209>] dummy_handler+0x3/0x7 SS:ESP 0069:dfc47e10
[ 21.970432] ---[ end trace c0b71f7e12cf3011 ]---
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit b7b30de53aef6ce773d34837ba7d8422bd3baeec upstream.
Previously, we assumed the only Device object immediately below the root
was the \_SB Scope (which the ACPI CA treats as a Device), so we forced
the HID of all such objects to ACPI_BUS_HID ("LNXSYBUS").
However, there are DSDTs that supply root-level Device objects with _HIDs.
This patch makes us pay attention to those _HIDs and only add the synthetic
ACPI_BUS_HID for root-level objects that do not supply their own _HID.
For example, this DSDT: https://bugzilla.kernel.org/show_bug.cgi?id=15605
contains:
Scope (_SB) {
...
}
Device (AMW0) {
Name (_HID, EisaId ("PNP0C14"))
...
}
and we should use "PNP0C14" for the AMW0 device, not "LNXSYBUS".
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Tested-by: Yong Wang <yong.y.wang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Thomas Renninger <trenn@suse.de>
Tested-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 9281b16caac1276817b77033c5b8a1f5ca30102c upstream.
The old IDE cmd64x checks the status of the CNTRL register to see if
the ports are enabled before probing them. pata_cmd64x doesn't do
this, which causes a HPMC on parisc when it tries to poke at the
secondary port because apparently the BAR isn't wired up (and a
non-responding piece of memory causes a HPMC).
Fix this by porting the CNTRL register port detection logic from IDE
cmd64x. In addition, following converns from Alan Cox, add a check to
see if a mobility electronics bridge is the immediate parent and forgo
the check if it is (prevents problems on hotplug controllers).
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit c754d9b6e04371fb398cdd2f5e77be895126be20 upstream.
s/ARTIM2/ARTTIM23/ in cmd648_bmdma_stop() while at it
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 03a849e6ddb604ff6a220b78637ee8e122ffc796 upstream.
Clear the primary channel pending interrupt bit
instead of the reserved one.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit a2bd62207af4be8f5fe815ff90cc309056407829 upstream.
Fix incorrect handling of recovery clocks value == 16 resulting
in overclocked recovery timings & potentially underclocked active
timings.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 89d3b3603bfb648e0113d8682d4f84dd18a776bd upstream.
Some places were using PCI_CLASS_REVISION instead of PCI_REVISION_ID, so
they weren't converted by commit 44c10138fd4bbc4b6d6bff0873c24902f2a9da65
(PCI: Change all drivers to use pci_device->revision).
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit b062962edb086011e94ec4d9eb3f6a6d814f2a8f upstream.
Commit e9c7469bb4f5 ("md: implment REQ_FLUSH/FUA support")
introduced R5_WantFUA flag and set rw to WRITE_FUA in that case.
However remaining code still checks whether rw is exactly same
as WRITE or not, so FUAed-write ends up with being treated as
READ. Fix it.
This bug has been present since 2.6.37 and the fix is suitable for any
-stable kernel since then. It is not clear why this has not caused
more problems.
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 9b2dc8b665932a8e681a7ab3237f60475e75e161 upstream.
The @bio->bi_phys_segments consists of active stripes count in the
lower 16 bits and processed stripes count in the upper 16 bits. So
logical-OR operator should be bitwise one.
This bug has been present since 2.6.27 and the fix is suitable for any
-stable kernel since then. Fortunately the bad code is only used on
error paths and is relatively unlikely to be hit.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 01393f3d5836b7d62e925e6f4658a7eb22b83a11 upstream.
Check pers->hot_remove_disk instead of pers->hot_add_disk in slot_store()
during disk removal. The linear personality only has ->hot_add_disk and
no ->hot_remove_disk, so that removing disk in the array resulted to
following kernel bug:
$ sudo mdadm --create /dev/md0 --level=linear --raid-devices=4 /dev/loop[0-3]
$ echo none | sudo tee /sys/block/md0/md/dev-loop2/slot
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [< (null)>] (null)
PGD c9f5d067 PUD 8575a067 PMD 0
Oops: 0010 [#1] SMP
CPU 2
Modules linked in: linear loop bridge stp llc kvm_intel kvm asus_atk0110 sr_mod cdrom sg
Pid: 10450, comm: tee Not tainted 3.0.0-rc1-leonard+ #173 System manufacturer System Product Name/P5G41TD-M PRO
RIP: 0010:[<0000000000000000>] [< (null)>] (null)
RSP: 0018:ffff880085757df0 EFLAGS: 00010282
RAX: ffffffffa00168e0 RBX: ffff8800d1431800 RCX: 000000000000006e
RDX: 0000000000000001 RSI: 0000000000000002 RDI: ffff88008543c000
RBP: ffff880085757e48 R08: 0000000000000002 R09: 000000000000000a
R10: 0000000000000000 R11: ffff88008543c2e0 R12: 00000000ffffffff
R13: ffff8800b4641000 R14: 0000000000000005 R15: 0000000000000000
FS: 00007fe8c9e05700(0000) GS:ffff88011fa00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 0000000000000000 CR3: 00000000b4502000 CR4: 00000000000406e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process tee (pid: 10450, threadinfo ffff880085756000, task ffff8800c9f08000)
Stack:
ffffffff8138496a ffff8800b4641000 ffff88008543c268 0000000000000000
ffff8800b4641000 ffff88008543c000 ffff8800d1431868 ffffffff81a78a90
ffff8800b4641000 ffff88008543c000 ffff8800d1431800 ffff880085757e98
Call Trace:
[<ffffffff8138496a>] ? slot_store+0xaa/0x265
[<ffffffff81384bae>] rdev_attr_store+0x89/0xa8
[<ffffffff8115a96a>] sysfs_write_file+0x108/0x144
[<ffffffff81106b87>] vfs_write+0xb1/0x10d
[<ffffffff8106e6c0>] ? trace_hardirqs_on_caller+0x111/0x135
[<ffffffff81106cac>] sys_write+0x4d/0x77
[<ffffffff814fe702>] system_call_fastpath+0x16/0x1b
Code: Bad RIP value.
RIP [< (null)>] (null)
RSP <ffff880085757df0>
CR2: 0000000000000000
---[ end trace ba5fc64319a826fb ]---
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 13f067537f34456443f61c950cd6dc37d1d5f3ee upstream.
cpufreq_stats leaves behind its sysfs entries, which causes a panic
when something stumbled across them.
(Discovered by unloading cpufreq_stats while powertop was loaded).
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit cd3c18ba2fac14b34d03cae111f215009735ea06 upstream.
Full-speed isoc endpoints specify interval in exponent based form in
frames, not microframes, so we need to adjust accordingly.
NEC xHCI host controllers will return an error code of 0x11 if a full
speed isochronous endpoint is added with the Interval field set to
something less than 3 (2^3 = 8 microframes, or one frame). It is
impossible for a full speed device to have an interval smaller than one
frame.
This was always an issue in the xHCI driver, but commit
dfa49c4ad120a784ef1ff0717168aa79f55a483a "USB: xhci - fix math in
xhci_get_endpoint_interval()" removed the clamping of the minimum value
in the Interval field, which revealed this bug.
This needs to be backported to stable kernels back to 2.6.31.
Reported-by: Matt Evans <matt@ozlabs.org>
Signed-off-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit a26d31cef06f43a76327c21235e75450869df2b8 upstream.
E.g. newer CAN 2.0 A/B <=> USB 2.0 converters report idProduct=f3c2.
Signed-off-by: Steffen Sledz <sledz@dresearch-fe.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 3824c1ddaf744be44b170a335332b9d6afe79254 upstream.
Protocol stall should not be fatal while reading port or hub status as it is
transient state. Currently hub EP0 STALL during port status read results in
failed device enumeration. This has been observed with ST-Ericsson (formerly
Philips) USB 2.0 Hub (04cc:1521) after connecting keyboard.
Signed-off-by: Libor Pechacek <lpechacek@suse.cz>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 4061fde2fa80f40cb27114f60500d38d0afcf350 upstream.
This adds the Nokia E7 and C7 to the list of devices in cdc-acm, allowing
the secondary ACM channel on the device to be exposed. Without this patch
the ACM driver won't claim this secondary channel as it's marked as
having a vendor-specific protocol.
Signed-off-by: Toby Gray <toby.gray@realvnc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 62fff811d73095bd95579d72f558f03c78f7914a upstream.
On my x86_64 system with >4GB of ram and swiotlb instead of
a hardware iommu (because I have a VIA chipset), the call
to pci_set_dma_mask (see below) with 40bits returns an error.
But it seems that the radeon driver is designed to have
need_dma32 = true exactly if pci_set_dma_mask is called
with 32 bits and false if it is called with 40 bits.
I have read somewhere that the default are 32 bits. So if the
call fails I suppose that need_dma32 should be set to true.
And indeed the patch fixes the problem I have had before
and which I had described here:
http://choon.net/forum/read.php?21,106131,115940
Acked-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 6a574b5b9b186e28abd3e571dfd1700c5220b510 upstream.
I found this while figuring out why gnome-shell would not run on my
Asus EeeBox PC EB1007. As a standalone "pc" this device cleary does not have
an internal panel, yet it claims it does. Add a quirk to fix this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit e522a7126c7c144a1dd14c6f217ac31e71082b1d upstream.
The following patch sets the MaxPayload setting to match the parent
reading when inserting a PCIE card into a hotplug slot. On our system,
the upstream bridge is set to 256, but when inserting a card, the card
setting defaults to 128. As soon as I/O is performed to the card it
starts receiving errors since the payload size is too small.
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jordan Hargrave <jordan_hargrave@dell.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit e73e079bf128d68284efedeba1fbbc18d78610f9 upstream.
In certain circumstances, we can get an oops from a torn down device.
Most notably this is from CD roms trying to call scsi_ioctl. The root
cause of the problem is the fact that after scsi_remove_device() has
been called, the queue is fully torn down. This is actually wrong
since the queue can be used until the sdev release function is called.
Therefore, we add an extra reference to the queue which is released in
sdev->release, so the queue always exists.
Reported-by: Parag Warudkar <parag.lkml@gmail.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 3b2710824e00d238554c13b5add347e6c701ab1a upstream.
The 'max_part' parameter controls the number of maximum partition
a nbd device can have. However if a user specifies very large
value it would exceed the limitation of device minor number and
can cause a kernel oops (or, at least, produce invalid device
nodes in some cases).
In addition, specifying large 'nbds_max' value causes same
problem for the same reason.
On my desktop, following command results to the kernel bug:
$ sudo modprobe nbd max_part=100000
kernel BUG at /media/Linux_Data/project/linux/fs/sysfs/group.c:65!
invalid opcode: 0000 [#1] SMP
last sysfs file: /sys/devices/virtual/block/nbd4/range
CPU 1
Modules linked in: nbd(+) bridge stp llc kvm_intel kvm asus_atk0110 sg sr_mod cdrom
Pid: 2522, comm: modprobe Tainted: G W 2.6.39-leonard+ #159 System manufacturer System Product Name/P5G41TD-M PRO
RIP: 0010:[<ffffffff8115aa08>] [<ffffffff8115aa08>] internal_create_group+0x2f/0x166
RSP: 0018:ffff8801009f1de8 EFLAGS: 00010246
RAX: 00000000ffffffef RBX: ffff880103920478 RCX: 00000000000a7bd3
RDX: ffffffff81a2dbe0 RSI: 0000000000000000 RDI: ffff880103920478
RBP: ffff8801009f1e38 R08: ffff880103920468 R09: ffff880103920478
R10: ffff8801009f1de8 R11: ffff88011eccbb68 R12: ffffffff81a2dbe0
R13: ffff880103920468 R14: 0000000000000000 R15: ffff880103920400
FS: 00007f3c49de9700(0000) GS:ffff88011f800000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 00007f3b7fe7c000 CR3: 00000000cd58d000 CR4: 00000000000406e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process modprobe (pid: 2522, threadinfo ffff8801009f0000, task ffff8801009a93a0)
Stack:
ffff8801009f1e58 ffffffff812e8f6e ffff8801009f1e58 ffffffff812e7a80
ffff880000000010 ffff880103920400 ffff8801002fd0c0 ffff880103920468
0000000000000011 ffff880103920400 ffff8801009f1e48 ffffffff8115ab6a
Call Trace:
[<ffffffff812e8f6e>] ? device_add+0x4f1/0x5e4
[<ffffffff812e7a80>] ? dev_set_name+0x41/0x43
[<ffffffff8115ab6a>] sysfs_create_group+0x13/0x15
[<ffffffff810b857e>] blk_trace_init_sysfs+0x14/0x16
[<ffffffff811ee58b>] blk_register_queue+0x4c/0xfd
[<ffffffff811f3bdf>] add_disk+0xe4/0x29c
[<ffffffffa007e2ab>] nbd_init+0x2ab/0x30d [nbd]
[<ffffffffa007e000>] ? 0xffffffffa007dfff
[<ffffffff8100020f>] do_one_initcall+0x7f/0x13e
[<ffffffff8107ab0a>] sys_init_module+0xa1/0x1e3
[<ffffffff814f3542>] system_call_fastpath+0x16/0x1b
Code: 41 57 41 56 41 55 41 54 53 48 83 ec 28 0f 1f 44 00 00 48 89 fb 41 89 f6 49 89 d4 48 85 ff 74 0b 85 f6 75 0b 48 83
7f 30 00 75 14 <0f> 0b eb fe b9 ea ff ff ff 48 83 7f 30 00 0f 84 09 01 00 00 49
RIP [<ffffffff8115aa08>] internal_create_group+0x2f/0x166
RSP <ffff8801009f1de8>
---[ end trace 753285ffbf72c57c ]---
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Cc: Laurent Vivier <Laurent.Vivier@bull.net>
Cc: Paul Clements <Paul.Clements@steeleye.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit ee37e09d81a4acf328f68189af12f116401f8c0f upstream.
This patch (as1335) fixes a bug in scsi_sysfs_add_sdev(). Its callers
always remove the device if anything goes wrong, so it should never
remove the device.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit d5469119f0098881ab7f991990ef4f81ef13a194 upstream.
This patch (as1334) fixes a bug in scsi_get_host_dev(). It
incorrectly calls get_device() on the new device's target.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 75f8ee8e01a6c96652f27da40d4bdac9e2e485f0 upstream.
This patch (as1333) fixes a bug in scsi_report_lun_scan(). If a
newly-allocated device can't be used, it should be deleted.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 63c4408074cbcc070ac17fc10e524800eb9bd0b0 upstream.
TI816X (common name for DM816x/C6A816x/AM389x family) devices configured
to boot as PCIe Endpoint have class code = 0. This makes kernel PCI bus
code to skip allocating BARs to these devices resulting into following
type of error when trying to enable them:
"Device 0000:01:00.0 not available because of resource collisions"
The device cannot be operated because of the above issue.
This patch adds a ID specific (TI VENDOR ID and 816X DEVICE ID based)
'early' fixup quirk to replace class code with
PCI_CLASS_MULTIMEDIA_VIDEO as class.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit af46566885a373b0a526932484cd8fef8de7b598 upstream.
When finding or allocating a ram disk device, brd_probe() did not take
partition numbers into account so that it can result to a different
device. Consider following example (I set CONFIG_BLK_DEV_RAM_COUNT=4
for simplicity) :
$ sudo modprobe brd max_part=15
$ ls -l /dev/ram*
brw-rw---- 1 root disk 1, 0 2011-05-25 15:41 /dev/ram0
brw-rw---- 1 root disk 1, 16 2011-05-25 15:41 /dev/ram1
brw-rw---- 1 root disk 1, 32 2011-05-25 15:41 /dev/ram2
brw-rw---- 1 root disk 1, 48 2011-05-25 15:41 /dev/ram3
$ sudo mknod /dev/ram4 b 1 64
$ sudo dd if=/dev/zero of=/dev/ram4 bs=4k count=256
256+0 records in
256+0 records out
1048576 bytes (1.0 MB) copied, 0.00215578 s, 486 MB/s
namhyung@leonhard:linux$ ls -l /dev/ram*
brw-rw---- 1 root disk 1, 0 2011-05-25 15:41 /dev/ram0
brw-rw---- 1 root disk 1, 16 2011-05-25 15:41 /dev/ram1
brw-rw---- 1 root disk 1, 32 2011-05-25 15:41 /dev/ram2
brw-rw---- 1 root disk 1, 48 2011-05-25 15:41 /dev/ram3
brw-r--r-- 1 root root 1, 64 2011-05-25 15:45 /dev/ram4
brw-rw---- 1 root disk 1, 1024 2011-05-25 15:44 /dev/ram64
After this patch, /dev/ram4 - instead of /dev/ram64 - was
accessed correctly.
In addition, 'range' passed to blk_register_region() should
include all range of dev_t that RAMDISK_MAJOR can address.
It does not need to be limited by partition numbers unless
'rd_nr' param was specified.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Cc: Laurent Vivier <Laurent.Vivier@bull.net>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 315980c8688c4b06713c1a5fe9d64cdf8ab57a72 upstream.
The 'max_part' parameter controls the number of maximum partition
a brd device can have. However if a user specifies very large
value it would exceed the limitation of device minor number and
can cause a kernel panic (or, at least, produce invalid device
nodes in some cases).
On my desktop system, following command kills the kernel. On qemu,
it triggers similar oops but the kernel was alive:
$ sudo modprobe brd max_part=100000
BUG: unable to handle kernel NULL pointer dereference at 0000000000000058
IP: [<ffffffff81110a9a>] sysfs_create_dir+0x2d/0xae
PGD 7af1067 PUD 7b19067 PMD 0
Oops: 0000 [#1] SMP
last sysfs file:
CPU 0
Modules linked in: brd(+)
Pid: 44, comm: insmod Tainted: G W 2.6.39-qemu+ #158 Bochs Bochs
RIP: 0010:[<ffffffff81110a9a>] [<ffffffff81110a9a>] sysfs_create_dir+0x2d/0xae
RSP: 0018:ffff880007b15d78 EFLAGS: 00000286
RAX: ffff880007b05478 RBX: ffff880007a52760 RCX: ffff880007b15dc8
RDX: ffff880007a4f900 RSI: ffff880007b15e48 RDI: ffff880007a52760
RBP: ffff880007b15da8 R08: 0000000000000002 R09: 0000000000000000
R10: ffff880007b15e48 R11: ffff880007b05478 R12: 0000000000000000
R13: ffff880007b05478 R14: 0000000000400920 R15: 0000000000000063
FS: 0000000002160880(0063) GS:ffff880007c00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000058 CR3: 0000000007b1c000 CR4: 00000000000006b0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 0000000000000000 DR7: 0000000000000000
Process insmod (pid: 44, threadinfo ffff880007b14000, task ffff880007acb980)
Stack:
ffff880007b15dc8 ffff880007b05478 ffff880007b15da8 00000000fffffffe
ffff880007a52760 ffff880007b05478 ffff880007b15de8 ffffffff81143c0a
0000000000400920 ffff880007a52760 ffff880007b05478 0000000000000000
Call Trace:
[<ffffffff81143c0a>] kobject_add_internal+0xdf/0x1a0
[<ffffffff81143da1>] kobject_add_varg+0x41/0x50
[<ffffffff81143e6b>] kobject_add+0x64/0x66
[<ffffffff8113bbe7>] blk_register_queue+0x5f/0xb8
[<ffffffff81140f72>] add_disk+0xdf/0x289
[<ffffffffa00040df>] brd_init+0xdf/0x1aa [brd]
[<ffffffffa0004000>] ? 0xffffffffa0003fff
[<ffffffffa0004000>] ? 0xffffffffa0003fff
[<ffffffff8100020a>] do_one_initcall+0x7a/0x12e
[<ffffffff8108516c>] sys_init_module+0x9c/0x1dc
[<ffffffff812ff4bb>] system_call_fastpath+0x16/0x1b
Code: 89 e5 41 55 41 54 53 48 89 fb 48 83 ec 18 48 85 ff 75 04 0f 0b eb fe 48 8b 47 18 49 c7 c4 70 1e 4d 81 48 85 c0 74 04 4c 8b 60 30
8b 44 24 58 45 31 ed 0f b6 c4 85 c0 74 0d 48 8b 43 28 48 89
RIP [<ffffffff81110a9a>] sysfs_create_dir+0x2d/0xae
RSP <ffff880007b15d78>
CR2: 0000000000000058
---[ end trace aebb1175ce1f6739 ]---
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Cc: Laurent Vivier <Laurent.Vivier@bull.net>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit f4808ca99a203f20b4475601748e44b25a65bdec upstream.
This patch adds a check that a block device has a request function
defined before it is used. Otherwise, misconfiguration can cause an oops.
Because we are allowing devices with zero size e.g. an offline multipath
device as in commit 2cd54d9bedb79a97f014e86c0da393416b264eb3
("dm: allow offline devices") there needs to be an additional check
to ensure devices are initialised. Some block devices, like a loop
device without a backing file, exist but have no request function.
Reproducer is trivial: dm-mirror on unbound loop device
(no backing file on loop devices)
dmsetup create x --table "0 8 mirror core 2 8 sync 2 /dev/loop0 0 /dev/loop1 0"
and mirror resync will immediatelly cause OOps.
BUG: unable to handle kernel NULL pointer dereference at (null)
? generic_make_request+0x2bd/0x590
? kmem_cache_alloc+0xad/0x190
submit_bio+0x53/0xe0
? bio_add_page+0x3b/0x50
dispatch_io+0x1ca/0x210 [dm_mod]
? read_callback+0x0/0xd0 [dm_mirror]
dm_io+0xbb/0x290 [dm_mod]
do_mirror+0x1e0/0x748 [dm_mirror]
Signed-off-by: Milan Broz <mbroz@redhat.com>
Reported-by: Zdenek Kabelac <zkabelac@redhat.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 7467571f4480b273007517b26297c07154c73924 upstream.
Cpuidle menu governor is using u32 as a temporary datatype for storing
nanosecond values which wrap around at 4.294 seconds. This causes errors
in predicted sleep times resulting in higher than should be C state
selection and increased power consumption. This also breaks cpuidle
state residency statistics.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit bc1f419c76a2d6450413ce4349f4e4a07be011d5 upstream.
i8k uses lahf to read the flag register in 64-bit code; early x86-64
CPUs, however, lack this instruction and we get an invalid opcode
exception at runtime.
Use pushf to load the flag register into the stack instead.
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Reported-by: Jeff Rickman <jrickman@myamigos.us>
Tested-by: Jeff Rickman <jrickman@myamigos.us>
Tested-by: Harry G McGavran Jr <w5pny@arrl.net>
Cc: Massimo Dal Zotto <dz@debian.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 9368a9a2378ab721f82f59430a135b4ce4ff5109 upstream.
Reported-by: Mark Davis <marked86@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 2b7aaf503d56216b847c8265421d2a7d9b42df3e upstream.
This patch (as1463) fixes a regression caused by commit
3df7169e73fc1d71a39cffeacc969f6840cdf52b (OHCI: work around for nVidia
shutdown problem).
The original problem encountered by people using NVIDIA chipsets was
that USB devices were not turning off when the system shut down. For
example, the LED on an optical mouse would remain on, draining a
laptop's battery. The problem was caused by a bug in the chipset; an
OHCI controller in the Reset state would continue to drive a bus reset
signal even after system shutdown. The workaround was to put the
controllers into the Suspend state instead.
It turns out that later NVIDIA chipsets do not suffer from this bug.
Instead some have the opposite bug: If a system is shut down while an
OHCI controller is in the Suspend state, USB devices remain powered!
On other systems, shutting down with a Suspended controller causes the
system to reboot immediately. Thus, working around the original bug
on some machines exposes other bugs on other machines.
The best solution seems to be to limit the workaround to OHCI
controllers with a low-numbered PCI product ID. I don't know exactly
at what point NVIDIA changed their chipsets; the value used here is a
guess. So far it was worked out okay for all the people who have
tested it.
This fixes Bugzilla #35032.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Andre "Osku" Schmidt <andre.osku.schmidt@googlemail.com>
Tested-by: Yury Siamashka <yurand2@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit b513d44751bfb609a3c20463f764c8ce822d63e9 upstream.
Dmitry's patch
dfa49c4ad120a784ef1ff0717168aa79f55a483a USB: xhci - fix math in xhci_get_endpoint_interval()
introduced a bug. The USB 2.0 spec says that full speed isochronous endpoints'
bInterval must be decoded as an exponent to a power of two (e.g. interval =
2^(bInterval - 1)). Full speed interrupt endpoints, on the other hand, don't
use exponents, and the interval in frames is encoded straight into bInterval.
Dmitry's patch was supposed to fix up the full speed isochronous to parse
bInterval as an exponent, but instead it changed the *interrupt* endpoint
bInterval decoding. The isochronous endpoint encoding was the same.
This caused full speed devices with interrupt endpoints (including mice, hubs,
and USB to ethernet devices) to fail under NEC 0.96 xHCI host controllers:
[ 100.909818] xhci_hcd 0000:06:00.0: add ep 0x83, slot id 1, new drop flags = 0x0, new add flags = 0x99, new slot info = 0x38100000
[ 100.909821] xhci_hcd 0000:06:00.0: xhci_check_bandwidth called for udev ffff88011f0ea000
...
[ 100.910187] xhci_hcd 0000:06:00.0: ERROR: unexpected command completion code 0x11.
[ 100.910190] xhci_hcd 0000:06:00.0: xhci_reset_bandwidth called for udev ffff88011f0ea000
When the interrupt endpoint was added and a Configure Endpoint command was
issued to the host, the host controller would return a very odd error message
(0x11 means "Slot Not Enabled", which isn't true because the slot was enabled).
Probably the host controller was getting very confused with the bad encoding.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Dmitry Torokhov <dtor@vmware.com>
Reported-by: Thomas Lindroth <thomas.lindroth@gmail.com>
Tested-by: Thomas Lindroth <thomas.lindroth@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 472b91274a6c6857877b5caddb875dcb5ecdfcb8 upstream.
composite.c always sets req->length to zero
and expects function driver's setup handlers
to return the amount of bytes to be used
on req->length. If we test against req->length
w_length will always be greater than req->length
thus making us always stall that particular
SEND_ENCAPSULATED_COMMAND request.
Tested against a Windows XP SP3.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit bf1f0a05d472e33dda8e5e69525be1584cdbd03a upstream.
on 9g20 they are the same as the 9260
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit b4026c4584cd70858d4d3450abfb1cd0714d4f32 upstream.
This patch fixes a problem where data received from the gps is sometimes
transferred incompletely to the serial port. If used in native mode now
all data received via the bulk queue will be forwarded to the serial
port.
Signed-off-by: Hermann Kneissel <herkne@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 37909fe588c9e09ab57cd267e98678a17ceda64a upstream.
Adding support for the TavIR STK500 (id 0403:FA33)
Atmel AVR programmer device based on FTDI FT232RL.
Signed-off-by: Benedek László <benedekl@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 3938a0b32dc12229e76735679b37095bc2bc1578 upstream.
Tested on my phone, the ttyUSB device is created and is fully
functional.
Signed-off-by: Elizabeth Jennifer Myers <elizabeth@sporksirc.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 4eff0b40a7174896b860312910e0db51f2dcc567 upstream.
This patch adds 4 device IDs for CP2102 based devices manufactured by
AC-Services. See http://www.ac-services.eu for further info.
Signed-off-by: Craig Shelley <craig@microtron.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
