| Age | Commit message (Collapse) | Author |
|---|
|
commit 68acc4afb040d98ddfd2cae0de09e2f4e1ee127f upstream.
Patch fix firmware error on "iw dev wlan0 scan passive" for
hardware scanning (with disable_hw_scan=0 module parameter).
iwl3945 0000:03:00.0: Microcode SW error detected. Restarting 0x82000008.
iwl3945 0000:03:00.0: Loaded firmware version: 15.32.2.9
iwl3945 0000:03:00.0: Start IWL Error Log Dump:
iwl3945 0000:03:00.0: Status: 0x0002A2E4, count: 1
iwl3945 0000:03:00.0: Desc Time asrtPC blink2 ilink1 nmiPC Line
iwl3945 0000:03:00.0: SYSASSERT (0x5) 0041263900 0x13756 0x0031C 0x00000 764
iwl3945 0000:03:00.0: Error Reply type 0x000002FC cmd C_SCAN (0x80) seq 0x443E ser 0x00340000
iwl3945 0000:03:00.0: Command C_SCAN failed: FW Error
iwl3945 0000:03:00.0: Can't stop Rx DMA.
We have disable ability to change passive scanning to active on
particular channel when traffic is detected on that channel. Otherwise
firmware will report error, when we try to do passive scan on radar
channels.
Reported-and-debugged-by: Pedro Francisco <pedrogfrancisco@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit b2ccccdca46273c7b321ecf5041c362cd950da20 upstream.
Check and report WARN only when its invalid
Resolves:
https://bugzilla.kernel.org/show_bug.cgi?id=42621
https://bugzilla.redhat.com/show_bug.cgi?id=766071
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit ff35e8b18984ad2a82cbd259fc07f0be4b34b1aa upstream.
This patch modified the setting value of
I2C Bus Transfer Rate Setting Counter regisrer.
Signed-off-by: Toshiharu Okada <toshiharu-linux@dsn.okisemi.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit f42af6c486aa5ca6ee62800cb45c5b252020509d upstream.
Since commit
"7488876... dt/net: Eliminate users of of_platform_{,un}register_driver"
there are two platform drivers named "mdio-gpio" registered.
I renamed the of variant to "mdio-ofgpio".
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit dfd00c4c8f3dfa1fd7cec45f83d98b2a49743dcd upstream.
Same devices can generate interrupt without properly setting bit in
INT_SOURCE_CSR register (spurious interrupt), what will cause IRQ line
will be disabled by interrupts controller driver.
We discovered that clearing INT_MASK_CSR stops such behaviour. We
previously first read that register, and then clear all know interrupt
sources bits and do not touch reserved bits. After this patch, we write
to all register content (I believe writing to reserved bits on that
register will not cause any problems, I tested that on my rt2800pci
device).
This fix very bad performance problem, practically making device
unusable (since worked without interrupts), reported in:
https://bugzilla.redhat.com/show_bug.cgi?id=658451
We previously tried to workaround that issue in commit
4ba7d9997869d25bd223dea7536fc1ce9fab3b3b "rt2800pci: handle spurious
interrupts", but it was reverted in commit
82e5fc2a34fa9ffea38f00c4066b7e600a0ca5e6
as thing, that will prevent to detect real spurious interrupts.
Reported-and-tested-by: Amir Hedayaty <hedayaty@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 2727b1753934e154931d6b3bdf20c9b2398457a2 upstream.
Correct OMAP_I2C_SYSC_REG offset in omap4 register map.
Offset 0x20 is reserved and OMAP_I2C_SYSC_REG has 0x10 as offset.
Signed-off-by: Alexander Aring <a.aring@phytec.de>
[khilman@ti.com: minor changelog edits]
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 895f3022523361e9b383cf48f51feb1f7d5e7e53 upstream.
The target code was not setting the additional sense length field in the
sense data it returned, which meant that at least the Linux stack
ignored the ASC/ASCQ fields. For example, without this patch, on a
tcm_loop device:
# sg_raw -v /dev/sda 2 0 0 0 0 0
gives
cdb to send: 02 00 00 00 00 00
SCSI Status: Check Condition
Sense Information:
Fixed format, current; Sense key: Illegal Request
Raw sense data (in hex):
70 00 05 00 00 00 00 00
while after the patch we correctly get the following (which matches what
a regular disk returns):
cdb to send: 02 00 00 00 00 00
SCSI Status: Check Condition
Sense Information:
Fixed format, current; Sense key: Illegal Request
Additional sense: Invalid command operation code
Raw sense data (in hex):
70 00 05 00 00 00 00 0a 00 00 00 00 20 00 00 00
00 00
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit ce136176fea522fc8f4c16dcae7e8ed1d890ca39 upstream.
Current SCSI specs say that the "response format" field in the standard
INQUIRY response should be set to 2, and all the real SCSI devices I
have do put 2 here. So let's do that too.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit cced5041ed5a2d1352186510944b0ddfbdbe4c0b upstream.
sym53c8xx_slave_destroy unconditionally assumes that sym53c8xx_slave_alloc has
succesesfully allocated a sym_lcb. This can lead to a NULL pointer dereference
(exposed by commit 4e6c82b).
Signed-off-by: Stratos Psomadakis <psomas@gentoo.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit d640113fe80e45ebd4a5b420b220d3f6bf37f682 upstream.
For UP processor, it is likely that no _MAT method or MADT table defined.
So currently acpi_get_cpuid(...) always return -1 for UP processor.
This is wrong. It should return valid value for CPU0.
In the other hand, BIOS may define multiple CPU handles even for UP
processor, for example
Scope (_PR)
{
Processor (CPU0, 0x00, 0x00000410, 0x06) {}
Processor (CPU1, 0x01, 0x00000410, 0x06) {}
Processor (CPU2, 0x02, 0x00000410, 0x06) {}
Processor (CPU3, 0x03, 0x00000410, 0x06) {}
}
We should only return valid value for CPU0's acpi handle.
And return invalid value for others.
http://marc.info/?t=132329819900003&r=1&w=2
Reported-and-tested-by: wallak@free.fr
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit da4d8b287abe783d30e968155614531a0937d090 upstream.
The call to acpi_os_validate_address in acpi_ds_get_region_arguments was
removed by mistake in commit 9ad19ac(ACPICA: Split large dsopcode and
dsload.c files).
Put it back.
Reported-and-bisected-by: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 8df0eb7c9d96f9e82f233ee8b74e0f0c8471f868 upstream.
In SRAT v1, we had 8bit proximity domain (PXM) fields; SRAT v2 provides
32bits for these. The new fields were reserved before.
According to the ACPI spec, the OS must disregrard reserved fields.
In order to know whether or not, we must know what version the SRAT
table has.
This patch stores the SRAT table revision for later consumption
by arch specific __init functions.
Signed-off-by: Kurt Garloff <kurt@garloff.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 39a74fdedd1c1461d6fb6d330b5266886513c98f upstream.
smp_call_function() only lets all other CPUs execute a specific function,
while we expect all CPUs do in intel_idle. Without the fix, we could have
one cpu which has auto_demotion enabled or has no broadcast timer setup.
Usually we don't see impact because auto demotion just harms power and the
intel_idle init is called in CPU 0, where boradcast timer delivers
interrupt, but this still could be a problem.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 5c2a9f06a9cd7194f884cdc88144866235dec07d upstream.
kvm -cpu host passes the original cpuid info to the guest.
Latest kvm version seem to return true for mwait_leaf cpuid
function on recent Intel CPUs. But it does not return mwait
C-states (mwait_substates), instead zero is returned.
While real CPUs seem to always return non-zero values, the intel
idle driver should not get active in kvm (mwait_substates == 0)
case and bail out.
Otherwise a Null pointer exception will happen later when the
cpuidle subsystem tries to get active:
[0.984807] BUG: unable to handle kernel NULL pointer dereference at (null)
[0.984807] IP: [<(null)>] (null)
...
[0.984807][<ffffffff8143cf34>] ? cpuidle_idle_call+0xb4/0x340
[0.984807][<ffffffff8159e7bc>] ? __atomic_notifier_call_chain+0x4c/0x70
[0.984807][<ffffffff81001198>] ? cpu_idle+0x78/0xd0
Reference:
https://bugzilla.novell.com/show_bug.cgi?id=726296
Signed-off-by: Thomas Renninger <trenn@suse.de>
CC: Bruno Friedmann <bruno@ioda-net.ch>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit ec8013beddd717d1740cfefb1a9b900deef85462 upstream.
A logical volume can map to just part of underlying physical volume.
In this case, it must be treated like a partition.
Based on a patch from Alasdair G Kergon.
Cc: Alasdair G Kergon <agk@redhat.com>
Cc: dm-devel@redhat.com
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 0bfc96cb77224736dfa35c3c555d37b3646ef35e upstream.
[ Changes with respect to 3.3: return -ENOTTY from scsi_verify_blk_ioctl
and -ENOIOCTLCMD from sd_compat_ioctl. ]
Linux allows executing the SG_IO ioctl on a partition or LVM volume, and
will pass the command to the underlying block device. This is
well-known, but it is also a large security problem when (via Unix
permissions, ACLs, SELinux or a combination thereof) a program or user
needs to be granted access only to part of the disk.
This patch lets partitions forward a small set of harmless ioctls;
others are logged with printk so that we can see which ioctls are
actually sent. In my tests only CDROM_GET_CAPABILITY actually occurred.
Of course it was being sent to a (partition on a) hard disk, so it would
have failed with ENOTTY and the patch isn't changing anything in
practice. Still, I'm treating it specially to avoid spamming the logs.
In principle, this restriction should include programs running with
CAP_SYS_RAWIO. If for example I let a program access /dev/sda2 and
/dev/sdb, it still should not be able to read/write outside the
boundaries of /dev/sda2 independent of the capabilities. However, for
now programs with CAP_SYS_RAWIO will still be allowed to send the
ioctls. Their actions will still be logged.
This patch does not affect the non-libata IDE driver. That driver
however already tests for bd != bd->bd_contains before issuing some
ioctl; it could be restricted further to forbid these ioctls even for
programs running with CAP_SYS_ADMIN/CAP_SYS_RAWIO.
Cc: linux-scsi@vger.kernel.org
Cc: Jens Axboe <axboe@kernel.dk>
Cc: James Bottomley <JBottomley@parallels.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[ Make it also print the command name when warning - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 577ebb374c78314ac4617242f509e2f5e7156649 upstream.
Introduce a wrapper around scsi_cmd_ioctl that takes a block device.
The function will then be enhanced to detect partition block devices
and, in that case, subject the ioctls to whitelisting.
Cc: linux-scsi@vger.kernel.org
Cc: Jens Axboe <axboe@kernel.dk>
Cc: James Bottomley <JBottomley@parallels.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit c4fad877cd0efb51d8180ae2eaa791c99c92051c upstream.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Acked-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 66f06127f34ad6e8a1b24a2c03144b694d19f99f upstream.
Just another eGalax device.
Please note that adding this device to have_special_driver
in hid-core.c is not required anymore.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@enac.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit bb9ff21072043634f147c05ac65dbf8185d4af6d upstream.
This patch adds USB ID for the touchpanel in Acer Iconia W500. The panel
supports up to five fingers, therefore the need for a new addition of panel
types.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@enac.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit e36f690b37945e0a9bb1554e1546eeec93f7d1f6 upstream.
This is just a renaming of USB_DEVICE_ID_DWAV_EGALAX_MULTITOUCH{N}
to USB_DEVICE_ID_DWAV_EGALAX_MULTITOUCH_{PID} to handle more eGalax
devices.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@enac.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 1fd8f047490dd0ec4e4db710fcbc1bd4798d944c upstream.
This allows ASUS Eee Slate touchscreens to work.
Signed-off-by: Chris Bagwell <chris@cnpbagwell.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 806e23e95f94a27ee445022d724060b9b45cb64a upstream.
There is a potential integer overflow in uvc_ioctl_ctrl_map(). When a
large xmap->menu_count is passed from the userspace, the subsequent call
to kmalloc() will allocate a buffer smaller than expected.
map->menu_count and map->menu_info would later be used in a loop (e.g.
in uvc_query_v4l2_ctrl), which leads to out-of-bound access.
The patch checks the ioctl argument and returns -EINVAL for zero or too
large values in xmap->menu_count.
Signed-off-by: Haogang Chen <haogangchen@gmail.com>
[laurent.pinchart@ideasonboard.com Prevent excessive memory consumption]
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 6c06108be53ca5e94d8b0e93883d534dd9079646 upstream.
If ctrls->count is too high the multiplication could overflow and
array_size would be lower than expected. Mauro and Hans Verkuil
suggested that we cap it at 1024. That comes from the maximum
number of controls with lots of room for expantion.
$ grep V4L2_CID include/linux/videodev2.h | wc -l
211
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit dd8df17fe83483d7ea06ff229895e35a42071599 upstream.
This patch fixes a failure to recognize SD cards reported on a Dell
Vostro with O2 Micro SD card reader. Patch 49c468f ("mmc: sd: add
support for uhs bus speed mode selection") caused the problem, by
setting the SDHCI_CTRL_HISPD flag even for legacy timings.
Signed-off-by: Alexander Elbs <alex@segv.de>
Acked-by: Philip Rakity <prakity@marvell.com>
Acked-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit c6ced0db08010ed75df221a2946c5228454b38d5 upstream.
When suspending host, the tuning timer shoule be deactivated.
And the HOST_NEEDS_TUNING flag should be set after tuning timer is
deactivated.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Aaron Lu <aaron.lu@amd.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 913047e9e5787a90696533a9f109552b7694ecc9 upstream.
This patch fixes the wrong comparison before setting the interface
voltage in DDR mode.
The assignment to the variable ddr before comaprison is either
ddr = MMC_1_2V_DDR_MODE; or ddr == MMC_1_8V_DDR_MODE. But the comparison
is done with the extended csd value if ddr == EXT_CSD_CARD_TYPE_DDR_1_2V.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Acked-by: Subhash Jadavani <subhashj@codeaurora.org>
Acked-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 7c1f59c9d5caf3a84f35549b5d58f3c055a68da5 upstream.
When adding checks for ACPI resource conflicts to many bus drivers,
not enough attention was paid to the error paths, and for several
drivers this causes 0 to be returned on error in some cases. Fix this
by properly returning a non-zero value on every error.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 72f0d453d81d35087b1d3ad7c8285628c2be6e1d upstream.
Patch ab50ff684707031ed4bad2fdd313208ae392e5bb broke UBI debugging messages:
before that commit when UBI debugging was enabled, users saw few useful
debugging messages after attaching an MTD device. However, that patch turned
'dbg_msg()' into 'pr_debug()', so to enable the debugging messages users have
to enable them first via /sys/kernel/debug/dynamic_debug/control, which is
very impractical.
This commit makes 'dbg_msg()' to use 'printk()' instead of 'pr_debug()', just
as it was before the breakage.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 4a59c797a18917a5cf3ff7ade296b46134d91e6a upstream.
Currently it's possible to create a volume without a name. E.g:
ubimkvol -n 32 -s 2MiB -t static /dev/ubi0 -N ""
After that vtbl_check() will always fail because it does not permit
empty strings.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit d90db4b12bc1b9b8a787ef28550fdb767ee25a49 upstream.
When downloading firmware into the device, the driver fails to check the
return when allocating an skb. When the allocation fails, a BUG can be
generated, as seen in https://bugzilla.redhat.com/show_bug.cgi?id=771656.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit eb31aae8cb5eb54e234ed2d857ddac868195d911 upstream.
Some Dell BIOSes have MCFG tables that don't report the entire
MMCONFIG area claimed by the chipset. If we move PCI devices into
that claimed-but-unreported area, they don't work.
This quirk reads the AMD MMCONFIG MSRs and adds PNP0C01 resources as
needed to cover the entire area.
Example problem scenario:
BIOS-e820: 00000000cfec5400 - 00000000d4000000 (reserved)
Fam 10h mmconf [d0000000, dfffffff]
PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xd0000000-0xd3ffffff] (base 0xd0000000)
pnp 00:0c: [mem 0xd0000000-0xd3ffffff]
pci 0000:00:12.0: reg 10: [mem 0xffb00000-0xffb00fff]
pci 0000:00:12.0: no compatible bridge window for [mem 0xffb00000-0xffb00fff]
pci 0000:00:12.0: BAR 0: assigned [mem 0xd4000000-0xd40000ff]
Reported-by: Lisa Salimbas <lisa.salimbas@canonical.com>
Reported-by: <thuban@singularity.fr>
Tested-by: dann frazier <dann.frazier@canonical.com>
References: https://bugzilla.kernel.org/show_bug.cgi?id=31602
References: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/647043
References: https://bugzilla.redhat.com/show_bug.cgi?id=770308
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 9e7860cee18241633eddb36a4c34c7b61d8cecbc upstream.
Haogang Chen found out that:
There is a potential integer overflow in process_msg() that could result
in cross-domain attack.
body = kmalloc(msg->hdr.len + 1, GFP_NOIO | __GFP_HIGH);
When a malicious guest passes 0xffffffff in msg->hdr.len, the subsequent
call to xb_read() would write to a zero-length buffer.
The other end of this connection is always the xenstore backend daemon
so there is no guest (malicious or otherwise) which can do this. The
xenstore daemon is a trusted component in the system.
However this seem like a reasonable robustness improvement so we should
have it.
And Ian when read the API docs found that:
The payload length (len field of the header) is limited to 4096
(XENSTORE_PAYLOAD_MAX) in both directions. If a client exceeds the
limit, its xenstored connection will be immediately killed by
xenstored, which is usually catastrophic from the client's point of
view. Clients (particularly domains, which cannot just reconnect)
should avoid this.
so this patch checks against that instead.
This also avoids a potential integer overflow pointed out by Haogang Chen.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Haogang Chen <haogangchen@gmail.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit aff132d95ffe14eca96cab90597cdd010b457af7 upstream.
The amount of memory required for tracking chain buffers is rather
large, and when the host credit count is big, memory allocation
failure occurs inside __get_free_pages.
The fix is to limit the number of chains to 100,000. In addition,
the number of host credits is limited to 30,000 IOs. However this
limitation can be overridden this using the command line option
max_queue_depth. The algorithm for calculating the
reply_post_queue_depth is changed so that it is equal to
(reply_free_queue_depth + 16), previously it was (reply_free_queue_depth * 2).
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 30c43282f3d347f47f9e05199d2b14f56f3f2837 upstream.
Added code to release the spinlock that is used to protect the
raid device list before calling a function that can block. The
blocking was causing a reschedule, and subsequently it is tried
to acquire the same lock, resulting in a panic (NMI Watchdog
detecting a CPU lockup).
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit a776c491ca5e38c26d9f66923ff574d041e747f4 upstream.
I traced a nasty kexec on panic boot failure to the fact that we had
screaming msi interrupts and we were not disabling the msi messages at
kernel startup. The booting kernel had not enabled those interupts so
was not prepared to handle them.
I can see no reason why we would ever want to leave the msi interrupts
enabled at boot if something else has enabled those interrupts. The pci
spec specifies that msi interrupts should be off by default. Drivers
are expected to enable the msi interrupts if they want to use them. Our
interrupt handling code reprograms the interrupt handlers at boot and
will not be be able to do anything useful with an unexpected interrupt.
This patch applies cleanly all of the way back to 2.6.32 where I noticed
the problem.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit e57e0d8e818512047fe379157c3f77f1b9fabffb upstream.
When we fail to erase a PEB, we free the corresponding erase entry object,
but then re-schedule this object if the error code was something like -EAGAIN.
Obviously, it is a bug to use the object after we have freed it.
Reported-by: Emese Revfy <re.emese@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit e801e128b2200c40a0ec236cf2330b2586b6e05a upstream.
Under some cases, when scrubbing the PEB if we did not get the lock on
the PEB it fails to scrub. Add that PEB again to the scrub list
Artem: minor amendments.
Signed-off-by: Bhavesh Parekh <bparekh@nvidia.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit e46e927b9b7e8d95526e69322855243882b7e1a3 upstream.
This allows the latest N-Trig devices to function properly.
BugLink: https://bugs.launchpad.net/bugs/724831
Signed-off-by: Chase Douglas <chase.douglas@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 3df96909b75835d487a9178761622b0cbd7310d4 upstream.
It would previously write basically random bits to PCI configuration space...
Not very surprising that the GPU tended to stop responding completely. The
resulting MCE even froze the whole machine sometimes.
Now resetting the GPU after a lockup has at least a fighting chance of
succeeding.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 28eebb703e28bc455ba704adb1026f76649b768c upstream.
We often end up missing fences on older asics with
writeback enabled which leads to delays in the userspace
accel code, so just disable it by default on those asics.
Reported-by: Helge Deller <deller@gmx.de>
Reported-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 92db7f6c860b8190571a9dc1fcbc16d003422fe8 upstream.
This change was verified to fix both issues with no video I've
investigated. I've also checked checksum calculation with fglrx on:
RV620, HD54xx, HD5450, HD6310, HD6320.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit e74a8f2edb92cb690b467cea0ab652c509e9f624 upstream.
Commit f44f7f96a20a ("RTC: Initialize kernel state from RTC") introduced a
potential infinite loop. If an alarm time contains a wildcard month and
an invalid day (> 31), or a wildcard year and an invalid month (>= 12),
the loop searching for the next matching date will never terminate. Treat
the invalid values as wildcards.
Fixes <http://bugs.debian.org/646429>, <http://bugs.debian.org/653331>
Reported-by: leo weppelman <leoweppelman@googlemail.com>
Reported-by: "P. van Gaans" <mailme667@yahoo.co.uk>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Jonathan Nieder <jrnieder@gmail.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <john.stultz@linaro.org>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 2f4478ccff7df845dc9c0f8996a96373122c4417 upstream.
stresstest needs at least two eraseblocks. Bail out gracefully if that
condition is not met. Fixes the following 'division by zero' OOPS:
[ 619.100000] mtd_stresstest: MTD device size 131072, eraseblock size 131072, page size 2048, count of eraseblocks 1, pages per eraseblock 64, OOB size 64
[ 619.120000] mtd_stresstest: scanning for bad eraseblocks
[ 619.120000] mtd_stresstest: scanned 1 eraseblocks, 0 are bad
[ 619.130000] mtd_stresstest: doing operations
[ 619.130000] mtd_stresstest: 0 operations done
[ 619.140000] Division by zero in kernel.
...
caused by
/* Read or write up 2 eraseblocks at a time - hence 'ebcnt - 1' */
eb %= (ebcnt - 1);
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 342ff28f5a2e5aa3236617bd2bddf6c749677ef2 upstream.
Some error paths in mtd_blkdevs were fixed in the following commit:
commit 94735ec4044a6d318b83ad3c5794e931ed168d10
mtd: mtd_blkdevs: fix error path in blktrans_open
But on these error paths, the block device's `dev->open' count is
already incremented before we check for errors. This meant that, while
the error path was handled correctly on the first time through
blktrans_open(), the device is erroneously considered already open on
the second time through.
This problem can be seen, for instance, when a UBI volume is
simultaneously mounted as a UBIFS partition and read through its
corresponding gluebi mtdblockX device. This results in blktrans_open()
passing its error checks (with `dev->open > 0') without actually having
a handle on the device. Here's a summarized log of the actions and
results with nandsim:
# modprobe nandsim
# modprobe mtdblock
# modprobe gluebi
# modprobe ubifs
# ubiattach /dev/ubi_ctrl -m 0
...
# ubimkvol /dev/ubi0 -N test -s 16MiB
...
# mount -t ubifs ubi0:test /mnt
# ls /dev/mtdblock*
/dev/mtdblock0 /dev/mtdblock1
# cat /dev/mtdblock1 > /dev/null
cat: can't open '/dev/mtdblock4': Device or resource busy
# cat /dev/mtdblock1 > /dev/null
CPU 0 Unable to handle kernel paging request at virtual address
fffffff0, epc == 8031536c, ra == 8031f280
Oops[#1]:
...
Call Trace:
[<8031536c>] ubi_leb_read+0x14/0x164
[<8031f280>] gluebi_read+0xf0/0x148
[<802edba8>] mtdblock_readsect+0x64/0x198
[<802ecfe4>] mtd_blktrans_thread+0x330/0x3f4
[<8005be98>] kthread+0x88/0x90
[<8000bc04>] kernel_thread_helper+0x10/0x18
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 3538c56329936c78f7d356889908790006d0124c upstream.
Use block_isbad to check and skip the bad blocks reading.
This will allow to get rid of the read errors if bad blocks
are present initially.
Signed-off-by: Roman Tereshonkov <roman.tereshonkov@nokia.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 556f063580db2953a7e53cd46b47724246320f60 upstream.
The array of unsigned long pointed by oops_page_used is allocated
by vmalloc which requires the size to be in bytes.
BITS_PER_LONG is equal to 32.
If we want to allocate memory for 32 pages with one bit per page then
32 / BITS_PER_LONG is equal to 1 byte that is 8 bits.
To fix it we need to multiply the result by sizeof(unsigned long) equal to 4.
Signed-off-by: Roman Tereshonkov <roman.tereshonkov@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
[Not upstream as it was fixed differently for 3.3 with a much more
"intrusive" rework of the driver - gregkh]
There is a race condition involving acm_tty_hangup() and acm_tty_close()
where hangup() would attempt to access tty->driver_data without proper
locking and NULL checking after close() has potentially already set it
to NULL. One possibility to (sporadically) trigger this behavior is to
perform a suspend/resume cycle with a running WWAN data connection.
This patch addresses the issue by introducing a NULL check for
tty->driver_data in acm_tty_hangup() protected by open_mutex and exiting
gracefully when hangup() is invoked on a device that has already been
closed.
Signed-off-by: Thilo-Alexander Ginkel <thilo@ginkel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 9ae89b0296e275d5a556068b40b7c2557a556a85 upstream.
mpt2sas_base_detach() call was removed from _scsih_remove() while
doing some code shuffling. Mainly when we work on adding code for
scsih_shutdown(). I have added back mpt2sas_base_detach() which will
get callled from _scsih_remove().
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
commit f7d9821a6a9c83450ac35e76d3709e32fd38b76f upstream.
If slave device already has a receive handler registered, then the
error unwind of bonding device enslave function is broken.
The following will leave a pointer to freed memory in the slave
device list, causing a later kernel panic.
# modprobe dummy
# ip li add dummy0-1 link dummy0 type macvlan
# modprobe bonding
# echo +dummy0 >/sys/class/net/bond0/bonding/slaves
The fix is to detach the slave (which removes it from the list)
in the unwind path.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Reviewed-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
