| Age | Commit message (Collapse) | Author |
|---|
|
mmc: Power quirk for ENE controllers
Support for these devices was broken for 2.6.18-rc1 and later by commit
146ad66eac836c0b976c98f428d73e1f6a75270d, which added voltage level support.
This restores the previous behaviour for these devices by ensuring that when
the voltage is changed, only one write to set the voltage is performed.
It may be that both writes are needed if the voltage is being changed between
two non-zero values or that it's safe to ensure that only one write is done
if the hardware only supports one voltage; I don't know whether either is the
case nor can I test since I have only the one SD reader (1524:0550), and it
supports just the one voltage.
Signed-off-by: Darren Salt <linux@youmustbejoking.demon.co.uk>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
sata_sil used to trigger HSM error if IRQ occurs during polling
command. This didn't matter because polling wasn't used in sata_sil.
However, as of 2.6.20, all IDENTIFYs are performed by polling and
device detection sometimes fails due to spurious IRQ. This patch
makes sata_sil ignore and clear spurious IRQ while executing commands
by polling.
This fixes bug#7996 and IMHO should also be included in -stable.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This updates the cx88-blackbird driver to be able to use the new cx23416
firmware image released by Hauppauge Computer Works, while retaining
compatibility with the older firmware images.
cx2341x firmware can be downloaded at: http://dl.ivtvdriver.org/ivtv/firmware/
(cherry picked from commit af70dbd3346999570db73b3bc3d4f7b7c004f2ea)
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Due to changes in the i2c handling in 2.6.20 this cx25840 bug surfaced,
causing the firmware load to fail for the ivtv driver. The correct
sequence is to first attach the i2c client, then use the client's
device to load the firmware.
(cherry picked from commit d55c7aec666658495e5b57a6b194c8c2a1ac255f)
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Acked-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
dvb-pll normally opens the i2c gate before attempting to communicate with
the pll, but the code for this device is not using dvb-pll. This should
be cleaned up in the future, but for now, just open the i2c gate at the
appropriate place in order to fix this driver bug.
(cherry picked from commit 2fe22dcdc79b8dd34e61a3f1231caffd6180a626)
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Without this patch, the device will not be detected after firmware download
on big endian systems.
(cherry picked from commit 1d1370a48ca285ebe197ecd3197a8d5f161bc291)
Signed-off-by: Jin-Bong lee <jinbong.lee@samsung.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Rework the cx23416 firmware loader so that it longer requires the
firmware size to be a multiple of 8KB. Until recently all cx2341x
firmware images were exactly 256KB, but newer firmware is larger than
that and also appears to have arbitrary size. We still must check
against a multiple of 4 bytes (because the cx23416 itself uses a 32
bit word size).
This fix is already in the upstream driver source and has proven
itself there; this is a backport for the 2.6.20.y kernel series.
(backported from commit 90060d32ca0a941b158994f78e60d0381871c84b)
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This introduces some extra cx23416 commands when streaming is
started. The addition of these commands fix random sporadic video
corruption that can take place when the video stream is temporarily
disrupted through loss of signal (e.g. changing the channel in the RF
tuner).
This fix is already in the upstream driver source and has proven
itself there; this is a backport for the 2.6.20.y kernel series.
(backported from commit 6fe7d2c4660174110c6872cacc4fc2acb6e00acf)
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Arjan van de Ven <arjan@infradead.org> reported an illegal re-usage of
the fileoperations struct if more than one dvb device (e.g. frontend) is
present.
This patch fixes this issue.
It allocates a new fileoperations struct each time a device is
registered and copies the default template fileops.
(backported from commit b61901024776b25ce7b8edc31bb1757c7382a88e)
Signed-off-by: Marcel Siegert <mws@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
There are two errors that can lead to recovery problems with raid10
when used in 'far' more (not the default).
Due to a '>' instead of '>=' the wrong block is located which would
result in garbage being written to some random location, quite
possible outside the range of the device, causing the newly
reconstructed device to fail.
The device size calculation had some rounding errors (it didn't round
when it should) and so recovery would go a few blocks too far which
would again cause a write to a random block address and probably
a device error.
The code for working with device sizes was fairly confused and spread
out, so this has been tided up a bit.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
BCM4309 devices aren't working properly as A PHYs aren't supported yet, but
we probe 802.11a cores anyway. This fixes it, while still allowing for A PHY code
to be developed in the future.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Cc: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The code in transmit timeout incorrectly assumed that netif_tx_lock
was not set.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Don't mark pause frames as errors. This problem caused transmitter not
to pause and would effectively take out a gigabit switch because the
it can't handle overrun.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as863) fixes a problem encountered sometimes when resuming
a port on a UHCI controller. The hardware may turn off the
Resume-Detect bit before turning off the Suspend bit, leading usbcore
to think that the port is still suspended and the resume has failed.
The patch makes uhci_finish_suspend() wait until both bits are safely
off.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as850b) disables remote wakeup (and everything else!) on
all EHCI ports when the shutdown() method is called. If remote wakeup
is left active then some systems will reboot instead of powering off.
This fixes Bugzilla #7828.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
[MTD] Fix regression in RedBoot partition scanning
This fixes a regression introduced by the attempt to handle RedBoot FIS
tables which are smaller than an eraseblock, in commit
0b47d654089c5ce3f2ea26a4485db9bcead1e515
It moves the recalculation of the number of slots in the table to the
correct place, and improves the heuristic for when we think we need to
byte-swap what we read from the flash.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Cc: Rod Whitby <rod@whitby.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The USB vendor and product IDs are not byteswapped appropriately, and
thus come out in the wrong endianness when fetched through the evdev
using ioctl() on big endian platforms.
Signed-off-by: Julien BLACHE <jb@jblache.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Commit 40b20c257a13c5a526ac540bc5e43d0fdf29792a by Len Brown introduced
a null pointer dereference in the appledisplay driver. This patch fixes
it.
Signed-off-by: Michael Hanselmann <linux-kernel@hansmi.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Since my commit 8252bbb1363b7fe963a3eb6f8a36da619a6f5a65 in 2.6.20-rc1,
host devices have a dummy driver attached. Alas the driver was not
registered before use if ieee1394 was loaded with disable_nodemgr=1.
This resulted in non-functional FireWire drivers or kernel lockup.
http://bugzilla.kernel.org/show_bug.cgi?id=7942
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This together with the phys_to_virt fix in lib/swiotlb.c::swiotlb_sync_sg
fixes video1394 DMA on machines with DMA bounce buffers, especially Intel
x86-64 machines with > 3GB RAM.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: David Moore <dcm@acm.org>
Tested-by: Nicolas Turro <Nicolas.Turro@inrialpes.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
md/bitmap tracks how many active write requests are pending on blocks
associated with each bit in the bitmap, so that it knows when it can
clear the bit (when count hits zero).
The counter has 14 bits of space, so if there are ever more than 16383,
we cannot cope.
Currently the code just calles BUG_ON as "all" drivers have request queue
limits much smaller than this.
However is seems that some don't. Apparently some multipath configurations
can allow more than 16383 concurrent write requests.
So, in this unlikely situation, instead of calling BUG_ON we now wait
for the count to drop down a bit. This requires a new wait_queue_head,
some waiting code, and a wakeup call.
Tested by limiting the counter to 20 instead of 16383 (writes go a lot slower
in that case...).
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
diff .prev/drivers/md/bitmap.c ./drivers/md/bitmap.c
|
|
Fix various bugs with aligned reads in RAID5.
It is possible for raid5 to be sent a bio that is too big
for an underlying device. So if it is a READ that we
pass stright down to a device, it will fail and confuse
RAID5.
So in 'chunk_aligned_read' we check that the bio fits within the
parameters for the target device and if it doesn't fit, fall back
on reading through the stripe cache and making lots of one-page
requests.
Note that this is the earliest time we can check against the device
because earlier we don't have a lock on the device, so it could change
underneath us.
Also, the code for handling a retry through the cache when a read
fails has not been tested and was badly broken. This patch fixes that
code.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as849) fixes a bug in the USB hub driver. A single
pre-allocated buffer is used for all port status reads, but nothing
guarantees exclusive use of the buffer. A mutex is added to provide
this guarantee.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
On Sun, Feb 04, 2007 at 04:51:38PM +0100, Eric Piel wrote:
> Hello,
>
> I've got a regression in 2.6.20-rc7 (-rc6 was fine) due to commit
> 4b95320fc4d21b0ff2f8604305dd6c851aff6096 ([AGPGART] intel_agp: restore
> graphics device's pci space early in resume).
I think the key to this failure is the last line here ..
> agpgart-intel 0000:00:00.0: resuming
> PM: Writing back config space on device 0000:00:02.0 at offset f (was 10b, writing 0)
> PM: Writing back config space on device 0000:00:02.0 at offset d (was dc, writing 0)
> PM: Writing back config space on device 0000:00:02.0 at offset b (was 10161025, writing 0)
> PM: Writing back config space on device 0000:00:02.0 at offset 5 (was f4000000, writing 0)
> PM: Writing back config space on device 0000:00:02.0 at offset 4 (was f8000008, writing 0)
> PM: Writing back config space on device 0000:00:02.0 at offset 2 (was 3000011, writing 0)
> PM: Writing back config space on device 0000:00:02.0 at offset 1 (was 2b00007, writing 0)
> PM: Writing back config space on device 0000:00:02.0 at offset 0 (was 11328086, writing 0)
> agpgart: Unable to remap memory.
This then blows up the next access to intel_i810_private.registers, which happens to
be intel_i810_insert_entries.
Either we need .suspend methods which unmap these regions, or we need
to skip trying to map them a second time on resume.
There's an ugly patch below which does the latter. Give it a try?
The intel-agp suspend/resume code has really grown into something
of a monster, and could use some refactoring in a big way.
Dave
From: Dave Jones <davej@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
If bcm43xx were to process an afterburner (ampdu) status response, Linux would oops. The
ampdu and intermediate status bits are properly named.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
There is a kernel oops on bcm43xx when resuming due to an overly tight timeout loop.
Signed-off-by: Larry Finger<Larry.Finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
eighty_ninty_three() had word 93 validitity check but not the 80c bit
test itself (bit 12). This increases the chance of incorrect wire
detection especially because host side cable detection is often
unreliable and we sometimes soley depend on drive side cable
detection. Fix it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Acked-by: Alan <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
80c test mask is at bits 18 and 19 of EIDE Controller Configuration
not 22 and 23. Fix it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
|
|
Correct assignment of DOT1XENABLE in WE-19 codepaths.
RX_UNENCRYPTED_EAPOL = 1 really means setting DOT1XENABLE _off_, and
vice versa. The original WE-19 patch erroneously reversed that. This
patch fixes association with unencrypted and WEP networks when using
wpa_supplicant.
It also adds two missing break statements that, left out, could result
in incorrect card configuration.
Applies to (I think) 2.6.19 and later.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The usage of the century bit was inverted on 2.6.19 following to PCF8563's
description, but it was not match to usage suggested by RTC8564's
datasheet. Anyway what MO_C=1 means can vary on each platform. This patch
is to detect its polarity in get_datetime routine. The default value of
c_polarity is 0 (MO_C=1 means 19xx) so that this patch does not change
current behavior even if get_datetime was not called before set_datetime.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@teamlog.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
That code doesn't do what its author apparently thought it would do...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] sd: udev accessing an uninitialized scsi_disk field results in a crash
[SCSI] st: A MTIOCTOP/MTWEOF within the early warning will cause the file number to be incorrect
[SCSI] qla4xxx: bug fixes
[SCSI] Fix scsi_add_device() for async scanning
|
|
smc911x_phy_configure's error handling unconditionally unlocks the
spinlock even if it wasn't locked. Patch fixes it.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
sd_probe() calls class_device_add() even before initializing the
sdkp->device variable. class_device_add() eventually results in the user mode
udev program to be called. udev program can read the the allow_restart
attribute of the newly created scsi device. This is resulting in a crash as
the show function for allow_restart (i.e sd_show_allow_restart) returns the
attribute value by reading the sdkp->device->allow_restart variable. As the
sdkp->device is not initialized before calling the user mode hotplug helper,
this results in a crash.
The patch below solves it by calling class_device_add() only after the
necessary fields in the scsi_disk structure are initialized properly.
Signed-off-by: Nagendra Singh Tomar <nagendra_tomar@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: Initialize nbytes for internal sg commands
libata: Fix ata_busy_wait() kernel docs
pata_via: Correct missing comments
pata_atiixp: propogate cable detection hack from drivers/ide to the new driver
ahci/pata_jmicron: fix JMicron quirk
|
|
Some LLDDs, like ipr, use nbytes and pad_len to determine
the total data transfer length of a command. Make sure
nbytes gets initialized for internally generated commands.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
The 8237S was added to the chipsets but not to the comments. Fix this
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
For all JMicrons except for 361 and 368, AHCI mode enable bits in the
Control(1) should be set. This used to be done in both ahci and
pata_jmicron but while moving programming to PCI quirk, it was removed
from ahci part while still left in pata_jmicron.
The implemented JMicron PCI quirk was incorrect in that it didn't
program AHCI mode enable bits. If pata_jmicron is loaded first and
programs those bits, the ahci ports work; otherwise, ahci device
detection fails miserably.
This patch makes JMicron PCI quirk clear SATA IDE mode bits and set
AHCI mode bits and remove the respective part from pata_jmicron.
Tested on JMB361, 363 and 368.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
spidernet : fix memory leak in spider_net_stop
e100: fix napi ifdefs removing needed code
netxen patches
|
|
We forget to call spider_net_free_rx_chain_contents which does the
actual dev_kfree_skb. New skbs are allocated from skbuff_head_cache
on each "ifconfig up" letting the cache grow infinitely.
This patch fixes it.
Signed-off-by: Jens Osterkamp <jens@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
e100: fix napi ifdefs removing needed code
From: Auke Kok <auke-jan.h.kok@intel.com>
The e100 driver is NAPI mode only. We need to netif_poll_disable
during suspend and shutdown. The non-NAPI driver code was removed
and is only avaiable in the out-of-tree e100 kernel driver.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
|
|
5709 A0 copper devices will not link up with some link partners
without this workaround.
Update driver to 1.5.5.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Noticed by JosephChan@via.com.tw.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Change SysRq showBlockedTasks from sysrq-X to sysrq-W and show that in the
Help message.
It was previously done via X, but X is already used for Xmon on ppc & powerpc
platforms and this collision needs to be avoided.
All callers of register_sysrq_key() are now marked in the sysrq op/key table.
I didn't mark 'h' as Help because Help is just printed for any unknown key,
such as '?'.
Added some omitted sysrq key entries in the sysrq.txt file.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Intel hosts, without long mode, and with nx support disabled in the bios
have an efer that is readable but not writable. This causes a lockup on
switch to guest mode (even though it should exit with reason 34 according
to the documentation).
Signed-off-by: Avi Kivity <avi@qumranet.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Remove these recently-added warnings. They don't tell us anythng very
interesting and Kumar says "On an embedded PPC reference system I see this
message 6 times when I've got no cards in the PCI slots."
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add special handling for the VT82C686.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Won't build (request_irq()/free_irq()), even if you manage to find an
s390 box with 8250-compatible UART they are expecting.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
