| Age | Commit message (Collapse) | Author |
|---|
|
commit 2f1f4d9b60396d2df4cff829bd5376ffc8ed9a2c upstream.
This reverts commit 985f61f7ee647ad570c05eab0b74915da2ac8e19.
This commit fixed certain cases, but ended up regressing others
due to limitations in the current KMS API. A proper fix is too
invasive for 3.6. Push it back to 3.7.
Reported-by: Andres Freund <andres@anarazel.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[bwh: Backported to 3.2: drop the DCE6 case]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 1b68a4ca2d038addb7314211d122fb6d7002b38b upstream.
If USB2 host controller probes fine but USB3 does not then we don't
remove the USB controller properly and lock up the system while the HUB
code will try to enumerate the USB2 controller and access memory which
is no longer available in case the dummy_hcd was compiled as a module.
This is a problem since 448b6eb1 ("USB: Make sure to fetch the BOS desc
for roothubs.) if used in USB3 mode because dummy does not provide this
descriptor and explodes later.
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 32ab31e01e2def6f48294d872d9bb42573aae00f upstream.
The ACPI tables in the Macbook Air 5,1 define a single IOAPIC with id 2,
but the only remapping unit described in the DMAR table matches id 0.
Interrupt remapping fails as a result, and the kernel panics with the
message "timer doesn't work through Interrupt-remapped IO-APIC."
To fix this, check each IOAPIC for a corresponding IOMMU. If an IOMMU is
not found, do not allow IRQ remapping to be enabled.
v2: Move check to parse_ioapics_under_ir(), raise log level to KERN_ERR,
and add FW_BUG to the log message
v3: Skip check if IOMMU doesn't support interrupt remapping and remove
existing check that the IOMMU count equals the IOAPIC count
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
[bwh: Backported to 3.2: adjust filename]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 2588aba002d14e938c2f56d299ecf3e7ce1302a5 upstream.
pch_uart_interrupt() takes priv->port.lock which leads to two recursive
spinlock calls if low_latency==1 or CONFIG_PREEMPT_RT_FULL=y (one
otherwise):
pch_uart_interrupt
spin_lock_irqsave(priv->port.lock, flags)
case PCH_UART_IID_RDR_TO (data ready)
handle_rx_to
push_rx
tty_port_tty_get
spin_lock_irqsave(&port->lock, flags) <--- already hold this lock
...
tty_flip_buffer_push
...
flush_to_ldisc
spin_lock_irqsave(&tty->buf.lock)
spin_lock_irqsave(&tty->buf.lock)
disc->ops->receive_buf(tty, char_buf)
n_tty_receive_buf
tty->ops->flush_chars()
uart_flush_chars
uart_start
spin_lock_irqsave(&port->lock) <--- already hold this lock
Avoid this by using a dedicated lock to protect the eg20t_port structure
and IO access to its membase. This is more consistent with the 8250
driver. Ensure priv->lock is always take prior to priv->port.lock when
taken at the same time.
V2: Remove inadvertent whitespace change.
V3: Account for oops_in_progress for the private lock in
pch_console_write().
Note: Like the 8250 driver, if a printk is introduced anywhere inside
the pch_console_write() critical section, the kernel will hang
on a recursive spinlock on the private lock. The oops case is
handled by using a trylock in the oops_in_progress case.
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
CC: Tomoya MORINAGA <tomoya.rohm@gmail.com>
CC: Feng Tang <feng.tang@intel.com>
CC: Alexander Stein <alexander.stein@systec-electronic.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2:
- Adjust context
- Drop changes to pch_console_write()]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 4188bba0e9e7ba58d231b528df495666f2742b74 upstream.
The driver should not try to switch to 1.8V when the SD 3.0 host
controller does not have any UHS capabilities bits set (SDR50, DDR50
or SDR104). See page 72 of "SD Specifications Part A2 SD Host
Controller Simplified Specification Version 3.00" under
"1.8V Signaling Enable". Instead of setting SDR12 and SDR25 in the host
capabilities data structure for all V3.0 host controllers, only set them
if SDR104, SDR50 or DDR50 is set in the host capabilities register. This
will prevent the switch to 1.8V later.
Signed-off-by: Al Cooper <acooper@gmail.com>
Acked-by: Arindam Nath <arindam.nath@amd.com>
Acked-by: Philip Rakity <prakity@marvell.com>
Acked-by: Girish K S <girish.shivananjappa@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit c531077f40abc9f2129c4c83a30b3f8d6ce1c0e7 upstream.
When using my Seagate FreeAgent GoFlex eSATAp external disk enclosure,
interface errors are always seen until 1.5Gbps is negotiated [1]. This
occurs using any disk in the enclosure, and when the disk is connected
directly with a generic passive eSATAp cable, we see stable 3Gbps
operation as expected.
Blacklist 3Gbps mode to avoid dataloss and the ~30s delay bus reset
and renegotiation incurs.
Signed-off-by: Daniel J Blueman <daniel@quora.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 1fa6535faf055cd71311ab887e94fc234f04ee18 upstream.
As pointed out by Gustavo and Marcel, all Apple-specific Broadcom
devices seen so far have the same interface class, subclass and
protocol numbers. This patch adds an entry which matches all of them,
using the new USB_VENDOR_AND_INTERFACE_INFO() macro.
In particular, this patch adds support for the MacBook Pro Retina
(05ac:8286), which is not in the present list.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Tested-by: Shea Levy <shea@shealevy.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 92c385f46b30f4954e9dd2d2005c12d233b479ea upstream.
Many Broadcom devices has a vendor specific devices class, with this rule
we match all existent and future controllers with this behavior.
We also remove old rules to that matches product id for Broadcom devices.
Tested-by: John Hommel <john.hommel@hp.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 61c964ba1748e984cb232b431582815899bf10fe upstream.
Patch adds support for BCM20702A0 device id (0a5c:21f4).
usb-devices after patch was applied:
T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0a5c ProdID=21f4 Rev=01.12
S: Manufacturer=Broadcom Corp
S: Product=BCM20702A0
S: SerialNumber=E4D53DF154D6
C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)
usb-devices before patch was applied:
T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0a5c ProdID=21f4 Rev=01.12
S: Manufacturer=Broadcom Corp
S: Product=BCM20702A0
S: SerialNumber=E4D53DF154D6
C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)
Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com>
Tested-by: Chris Gagnon <chris.gagnon@canonical.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 8871e99f89b7d7b1ea99de550eea2a56273f42ab upstream.
Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=24222
Signed-off-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 0d00dc2611abbe6ad244d50569c2ee82ce42846c upstream.
This patch (as1607) fixes a race that can occur if a USB host
controller is removed while a process is reading the
/sys/kernel/debug/usb/devices file.
The usb_device_read() routine uses the bus->root_hub pointer to
determine whether or not the root hub is registered. The is not a
valid test, because the pointer is set before the root hub gets
registered and remains set even after the root hub is unregistered and
deallocated. As a result, usb_device_read() or usb_device_dump() can
access freed memory, causing an oops.
The patch changes the test to use the hcd->rh_registered flag, which
does get set and cleared at the appropriate times. It also makes sure
to hold the usb_bus_list_lock mutex while setting the flag, so that
usb_device_read() will become aware of new root hubs as soon as they
are registered.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 80b4812407c6b1f66a4f2430e69747a13f010839 upstream.
The 'enough' function is written to work with 'near' arrays only
in that is implicitly assumes that the offset from one 'group' of
devices to the next is the same as the number of copies.
In reality it is the number of 'near' copies.
So change it to make this number explicit.
This bug makes it possible to run arrays without enough drives
present, which is dangerous.
It is appropriate for an -stable kernel, but will almost certainly
need to be modified for some of them.
Reported-by: Jakub Husák <jakub@gooseman.cz>
Signed-off-by: NeilBrown <neilb@suse.de>
[bwh: Backported to 3.2: s/geo->/conf->/]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit c3c4555edd10dbc0b388a0125b9c50de5e79af05 upstream.
Always clear QUEUE_FLAG_ADD_RANDOM if any underlying device does not
have it set. Otherwise devices with predictable characteristics may
contribute entropy.
QUEUE_FLAG_ADD_RANDOM specifies whether or not queue IO timings
contribute to the random pool.
For bio-based targets this flag is always 0 because such devices have no
real queue.
For request-based devices this flag was always set to 1 by default.
Now set it according to the flags on underlying devices. If there is at
least one device which should not contribute, set the flag to zero: If a
device, such as fast SSD storage, is not suitable for supplying entropy,
a request-based queue stacked over it will not be either.
Because the checking logic is exactly same as for the rotational flag,
share the iteration function with device_is_nonrot().
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit ba1cbad93dd47223b1f3b8edd50dd9ef2abcb2ed upstream.
The access beyond the end of device BUG_ON that was introduced to
dm_request_fn via commit 29e4013de7ad950280e4b2208 ("dm: implement
REQ_FLUSH/FUA support for request-based dm") was an overly
drastic (but simple) response to this situation.
I have received a report that this BUG_ON was hit and now think
it would be better to use dm_kill_unmapped_request() to fail the clone
and original request with -EIO.
map_request() will assign the valid target returned by
dm_table_find_target to tio->ti. But when the target
isn't valid tio->ti is never assigned (because map_request isn't
called); so add a check for tio->ti != NULL to dm_done().
Reported-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit deb09ddaff1435f72dd598d38f9b58354c68a5ec upstream.
Sandy bridge EDAC is calculating the memory size with overflow.
Basically, the size field and the integer calculation is using 32 bits.
More bits are needed, when the DIMM memories have high density.
The net result is that memories are improperly reported there, when
high-density DIMMs are used:
EDAC DEBUG: in drivers/edac/sb_edac.c, line at 591: mc#0: channel 0, dimm 0, -16384 Mb (-4194304 pages) bank: 8, rank: 2, row: 0x10000, col: 0x800
EDAC DEBUG: in drivers/edac/sb_edac.c, line at 591: mc#0: channel 1, dimm 0, -16384 Mb (-4194304 pages) bank: 8, rank: 2, row: 0x10000, col: 0x800
As the number of pages value is handled at the EDAC core as unsigned
ints, the driver shows the 16 GB memories at sysfs interface as 16760832
MB! The fix is simple: calculate the number of pages as unsigned 64-bits
integer.
After the patch, the memory size (16 GB) is properly detected:
EDAC DEBUG: in drivers/edac/sb_edac.c, line at 592: mc#0: channel 0, dimm 0, 16384 Mb (4194304 pages) bank: 8, rank: 2, row: 0x10000, col: 0x800
EDAC DEBUG: in drivers/edac/sb_edac.c, line at 592: mc#0: channel 1, dimm 0, 16384 Mb (4194304 pages) bank: 8, rank: 2, row: 0x10000, col: 0x800
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[bwh: Backported to 3.2:
- Adjust context
- Debug log function is debugf0(), not edac_dbg()]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit b1268d3737c6316016026245eef276eda6b0a621 upstream.
For GPIOs of gpio-lpc32xx, gpio_direction_output() ignores the value argument
(initial value of output). This patch fixes this by setting the level
accordingly.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 5f0ecb907deb1e6f28071ee3bd568903b9da1be4 upstream.
The quirk introduced with commit
00250ec90963b7ef6678438888f3244985ecde14 (hwmon: fam15h_power: fix
bogus values with current BIOSes) is not only required during driver
load but also when system resumes from suspend. The BIOS might set the
previously recommended (but unsuitable) initilization value for the
running average range register during resume.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Tested-by: Andreas Hartmann <andihartmann@01019freenet.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 596264082f10dd4a567c43d4526b2f54ac5520bc upstream.
This patch fixes an issue introduced after commit 4ea5454203d991ec
("HID: Fix race condition between driver core and ll-driver").
After that commit, hid-core discards any incoming packet that arrives while
hid driver's probe function is being executed.
This broke the enumeration process of hid-logitech-dj, that must receive
control packets in-band with the mouse and keyboard packets. Discarding mouse
or keyboard data at the very begining is usually fine, but it is not the case
for control packets.
This patch forces a re-enumeration of the paired devices when a packet arrives
that comes from an unknown device.
Based on a patch originally written by Benjamin Tissoires.
Signed-off-by: Nestor Lopez Casado <nlopezcasad@logitech.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 8a55ade76551e3927b4e41ee9e7751875d18bc25 upstream.
Allocate a structure not a pointer to it !
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit d8dc3494f77a5cc3b274bae36f7e74e85cf8a407 upstream.
On a system with a logitech wireless keyboard/mouse and DMA-API debugging
enabled, this warning appears at boot:
kernel: WARNING: at lib/dma-debug.c:929 check_for_stack.part.12+0x70/0xa7()
kernel: Hardware name: MS-7593
kernel: uhci_hcd 0000:00:1d.1: DMA-API: device driver maps memory fromstack [addr=ffff8801b0079c29]
Make logi_dj_recv_query_paired_devices and logi_dj_recv_switch_to_dj_mode
use a structure allocated with kzalloc rather than a stack based one.
Signed-off-by: Marc Dionne <marc.c.dionne@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 765031668fb2b064aebd9a568e5ad794cbe3413a upstream.
The user can only experience the bug if she pairs 6 devices to a Unifying
receiver. The sixth paired device would not work.
The value changed is actually a bitmask that enables reporting from each
paired device. As the sixth bit was not set, the sixth device reports are
ignored by the receiver and never get to the driver.
Signed-off-by: Nestor Lopez Casado <nlopezcasad@logitech.com>
drivers/hid/hid-logitech-dj.c | 2 +-
1 files changed, 1 insertions(+), 1 deletions(-)
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit ab04c8bd423edb03e2148350a091836c196107fc upstream.
This patch fixes an oops which occurs when unloading the driver, while the
network interface is still up. The problem is that first the io mapping is
teared own, then the CAN device is unregistered, resulting in accessing the
hardware's iomem:
[ 172.744232] Unable to handle kernel paging request at virtual address c88b0040
[ 172.752441] pgd = c7be4000
[ 172.755645] [c88b0040] *pgd=87821811, *pte=00000000, *ppte=00000000
[ 172.762207] Internal error: Oops: 807 [#1] PREEMPT ARM
[ 172.767517] Modules linked in: ti_hecc(-) can_dev
[ 172.772430] CPU: 0 Not tainted (3.5.0alpha-00037-g3554cc0 #126)
[ 172.778961] PC is at ti_hecc_close+0xb0/0x100 [ti_hecc]
[ 172.784423] LR is at __dev_close_many+0x90/0xc0
[ 172.789123] pc : [<bf00c768>] lr : [<c033be58>] psr: 60000013
[ 172.789123] sp : c5c1de68 ip : 00040081 fp : 00000000
[ 172.801025] r10: 00000001 r9 : c5c1c000 r8 : 00100100
[ 172.806457] r7 : c5d0a48c r6 : c5d0a400 r5 : 00000000 r4 : c5d0a000
[ 172.813232] r3 : c88b0000 r2 : 00000001 r1 : c5d0a000 r0 : c5d0a000
[ 172.820037] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
[ 172.827423] Control: 10c5387d Table: 87be4019 DAC: 00000015
[ 172.833404] Process rmmod (pid: 600, stack limit = 0xc5c1c2f0)
[ 172.839447] Stack: (0xc5c1de68 to 0xc5c1e000)
[ 172.843994] de60: bf00c6b8 c5c1dec8 c5d0a000 c5d0a000 00200200 c033be58
[ 172.852478] de80: c5c1de44 c5c1dec8 c5c1dec8 c033bf2c c5c1de90 c5c1de90 c5d0a084 c5c1de44
[ 172.860992] dea0: c5c1dec8 c033c098 c061d3dc c5d0a000 00000000 c05edf28 c05edb34 c000d724
[ 172.869476] dec0: 00000000 c033c2f8 c5d0a084 c5d0a084 00000000 c033c370 00000000 c5d0a000
[ 172.877990] dee0: c05edb00 c033c3b8 c5d0a000 bf00d3ac c05edb00 bf00d7c8 bf00d7c8 c02842dc
[ 172.886474] df00: c02842c8 c0282f90 c5c1c000 c05edb00 bf00d7c8 c0283668 bf00d7c8 00000000
[ 172.894989] df20: c0611f98 befe2f80 c000d724 c0282d10 bf00d804 00000000 00000013 c0068a8c
[ 172.903472] df40: c5c538e8 685f6974 00636365 c61571a8 c5cb9980 c61571a8 c6158a20 c00c9bc4
[ 172.911987] df60: 00000000 00000000 c5cb9980 00000000 c5cb9980 00000000 c7823680 00000006
[ 172.920471] df80: bf00d804 00000880 c5c1df8c 00000000 000d4267 befe2f80 00000001 b6d90068
[ 172.928985] dfa0: 00000081 c000d5a0 befe2f80 00000001 befe2f80 00000880 b6d90008 00000008
[ 172.937469] dfc0: befe2f80 00000001 b6d90068 00000081 00000001 00000000 befe2eac 00000000
[ 172.945983] dfe0: 00000000 befe2b18 00023ba4 b6e6addc 60000010 befe2f80 a8e00190 86d2d344
[ 172.954498] [<bf00c768>] (ti_hecc_close+0xb0/0x100 [ti_hecc]) from [<c033be58>] (__dev__registered_many+0xc0/0x2a0)
[ 172.984161] [<c033c098>] (rollback_registered_many+0xc0/0x2a0) from [<c033c2f8>] (rollback_registered+0x20/0x30)
[ 172.994750] [<c033c2f8>] (rollback_registered+0x20/0x30) from [<c033c370>] (unregister_netdevice_queue+0x68/0x98)
[ 173.005401] [<c033c370>] (unregister_netdevice_queue+0x68/0x98) from [<c033c3b8>] (unregister_netdev+0x18/0x20)
[ 173.015899] [<c033c3b8>] (unregister_netdev+0x18/0x20) from [<bf00d3ac>] (ti_hecc_remove+0x60/0x80 [ti_hecc])
[ 173.026245] [<bf00d3ac>] (ti_hecc_remove+0x60/0x80 [ti_hecc]) from [<c02842dc>] (platform_drv_remove+0x14/0x18)
[ 173.036712] [<c02842dc>] (platform_drv_remove+0x14/0x18) from [<c0282f90>] (__device_release_driver+0x7c/0xbc)
Cc: Anant Gole <anantgole@ti.com>
Tested-by: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit e21093ef6fb4cbecdf926102286dbe280ae965db upstream.
The Revision 1.0 Janz CMOD-IO Carrier Board does not have support for
the reset registers. To support older hardware, the code is changed to
use the hardware reset register on the Janz VMOD-ICAN3 hardware itself.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 8669cf6793bb38307a30fb6b9565ddc8840ebd3f upstream.
On Toshiba Satellite C850D, the touchpad and the keyboard might randomly
not work at boot. Preventing MUX mode activation solves this issue.
Signed-off-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit ed3770a9cd5764a575b83810ea679bbff2b03082 upstream.
Signed-off-by: Søren Holm <sgh@sgh.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2: adjust filename]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 3ceefe4319636d89d4bdf40dca9471970f942e4f upstream.
The 'name' sysfs attribute is mandatory for hwmon devices, but was missing
in this driver.
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 256d0eaac87da1e993190846064f339f4c7a63f5 upstream.
If a command status of CMD_PROTOCOL_ERR is received, this
information should be conveyed to the SCSI mid layer, not
dropped on the floor. CMD_PROTOCOL_ERR may be received
from the Smart Array for any commands destined for an external
RAID controller such as a P2000, or commands destined for tape
drives or CD/DVD-ROM drives, if for instance a cable is
disconnected. This mostly affects multipath configurations, as
disconnecting a cable on a non-multipath configuration is not
going to do anything good regardless of whether CMD_PROTOCOL_ERR
is handled correctly or not. Not handling CMD_PROTOCOL_ERR
correctly in a multipath configaration involving external RAID
controllers may cause data corruption, so this is quite a serious
bug. This bug should not normally cause a problem for direct
attached disk storage.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 61c6e7531d3b66b33187b8cdd700fd8ab93ffd62 upstream.
kzalloc could return NULL. Hence add a check to avoid
NULL pointer dereference.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
[bwh: Backported to 3.2: adjust context and error label]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 4e21f4eaa49f78d3e977e316514c941053871c76 upstream.
The 'name' sysfs attribute is mandatory for hwmon devices, but was missing
in this driver.
Cc: Paul Thomas <pthomas8589@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Paul Thomas <pthomas8589@gmail.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 10cce6d8b5af0b32bc4254ae4a28423a74c0921c upstream.
This patch checks whether HBA is SAS2008 B0 controller.
if it is a SAS2008 B0 controller then it use IO-APIC interrupt instead of MSIX,
as SAS2008 B0 controller doesn't support MSIX interrupts.
[jejb: fix whitespace problems]
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit d6532207116307eb7ecbfa7b9e02c53230096a50 upstream.
This patch fixes the following kernel panic invoked by uninitialized fields
in the chip initialization for the 1G bnx2 iSCSI offload.
One of the bits in the chip initialization is being used by the latest
firmware to control overflow packets. When this control bit gets enabled
erroneously, it would ultimately result in a bad packet placement which would
cause the bnx2 driver to dereference a NULL ptr in the placement handler.
This can happen under certain stress I/O environment under the Linux
iSCSI offload operation.
This change only affects Broadcom's 5709 chipset.
Unable to handle kernel NULL pointer dereference at 0000000000000008 RIP:
[<ffffffff881f0e7d>] :bnx2:bnx2_poll_work+0xd0d/0x13c5
Pid: 0, comm: swapper Tainted: G ---- 2.6.18-333.el5debug #2
RIP: 0010:[<ffffffff881f0e7d>] [<ffffffff881f0e7d>] :bnx2:bnx2_poll_work+0xd0d/0x13c5
RSP: 0018:ffff8101b575bd50 EFLAGS: 00010216
RAX: 0000000000000005 RBX: ffff81007c5fb180 RCX: 0000000000000000
RDX: 0000000000000ffc RSI: 00000000817e8000 RDI: 0000000000000220
RBP: ffff81015bbd7ec0 R08: ffff8100817e9000 R09: 0000000000000000
R10: ffff81007c5fb180 R11: 00000000000000c8 R12: 000000007a25a010
R13: 0000000000000000 R14: 0000000000000005 R15: ffff810159f80558
FS: 0000000000000000(0000) GS:ffff8101afebc240(0000) knlGS:0000000000000000
CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b
CR2: 0000000000000008 CR3: 0000000000201000 CR4: 00000000000006a0
Process swapper (pid: 0, threadinfo ffff8101b5754000, task ffff8101afebd820)
Stack: 000000000000000b ffff810159f80000 0000000000000040 ffff810159f80520
ffff810159f80500 00cf00cf8008e84b ffffc200100939e0 ffff810009035b20
0000502900000000 000000be00000001 ffff8100817e7810 00d08101b575bea8
Call Trace:
<IRQ> [<ffffffff8008e0d0>] show_schedstat+0x1c2/0x25b
[<ffffffff881f1886>] :bnx2:bnx2_poll+0xf6/0x231
[<ffffffff8000c9b9>] net_rx_action+0xac/0x1b1
[<ffffffff800125a0>] __do_softirq+0x89/0x133
[<ffffffff8005e30c>] call_softirq+0x1c/0x28
[<ffffffff8006d5de>] do_softirq+0x2c/0x7d
[<ffffffff8006d46e>] do_IRQ+0xee/0xf7
[<ffffffff8005d625>] ret_from_intr+0x0/0xa
<EOI> [<ffffffff801a5780>] acpi_processor_idle_simple+0x1c5/0x341
[<ffffffff801a573d>] acpi_processor_idle_simple+0x182/0x341
[<ffffffff801a55bb>] acpi_processor_idle_simple+0x0/0x341
[<ffffffff80049560>] cpu_idle+0x95/0xb8
[<ffffffff80078b1c>] start_secondary+0x479/0x488
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit b98b60167279df3acac9422c3c9820d9ebbcf9fb upstream.
Clear Audio Enable bit to trigger unsolicated event to notify Audio
Driver part the HDMI hot plug change. The patch fixed the bug when
remove HDMI cable the bit was not cleared correctly.
In intel_hdmi_dpms(), if intel_hdmi->has_audio been true, the "Audio enable bit" will
be set to trigger unsolicated event to notify Alsa driver the change.
intel_hdmi->has_audio will be reset to false from intel_hdmi_detect() after
remove the hdmi cable, here's debug log:
[ 187.494153] [drm:output_poll_execute], [CONNECTOR:17:HDMI-A-1] status updated from 1 to 2
[ 187.525349] [drm:intel_hdmi_detect], HDMI: has_audio = 0
so when comes back to intel_hdmi_dpms(), the "Audio enable bit" will not be cleared. And this
cause the eld infomation and pin presence doesnot update accordingly in alsa driver side.
This patch will also trigger unsolicated event to alsa driver to notify the hot plug event:
[ 187.853159] ALSA sound/pci/hda/patch_hdmi.c:772 HDMI hot plug event: Codec=3 Pin=5 Presence_Detect=0 ELD_Valid=1
[ 187.853268] ALSA sound/pci/hda/patch_hdmi.c:990 HDMI status: Codec=3 Pin=5 Presence_Detect=0 ELD_Valid=0
Signed-off-by: Wang Xingchao <xingchao.wang@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 7e81a42e341a4f15d76624b7c02ffb21b085b56f upstream.
Pin-leaks persist and we get the perennial bug reports of machine
lockups to the BUG_ON(pin_count==MAX). If we instead loudly report that
the object cannot be pinned at that time it should prevent the driver from
locking up, and hopefully restore a semblance of working whilst still
leaving us a OOPS to debug.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit c456797681db814f4f5b36909e8e94047bf53d9c upstream.
Avoid the construction of a malformed DMA request sent to
the DMA controller.
Log message is for debug only because this condition is unlikely to
append and may only trigger at driver development time.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit c618a9be0e8c0f36baee2560860a0118a428fb26 upstream.
s/dma_memcpy/slave_sg/ and it is sg length that we are
talking about.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit e020a83d0942a5aceac35986500c9834efc8707d upstream.
Fixes big endian host configuration parameters.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit ed205b361956c96e0d8c09a8c9135a6a79cd9541 upstream.
ssid len is 32 bit and needs endian conversion for big endian systems.
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 022e1d0680c7b4366017393417b8758be5abcee8 upstream.
There are a number of problems that occur for the latest version
of the Realtek RTL8188CE device with the in-kernel driver. These
include selection of the wrong firmware, and system lockup. A full
fix is known, but is too invasive for inclusion in stable. This patch
fixes the problem with loading the wrong firmware, and logs a message
that the device may not work for kernels 3.6 and older.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Anisse Astier <anisse@astier.eu>
Cc: Li Chaoming <chaoming_li@realsil.com.cn>
Tested-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 308b135e4fcc00c80c07e0e04e7afa8edf78583c upstream.
kdump can be interrupted by watchdog timer when the timer is left
activated on the crash kernel. Changed the hpwdt driver to disable
watchdog timer at boot-time. This assures that watchdog timer is
disabled until /dev/watchdog is opened, and prevents watchdog timer
to be left running on the crash kernel.
Signed-off-by: Toshi Kani <toshi.kani@hp.com>
Tested-by: Lisa Mitchell <lisa.mitchell@hp.com>
Signed-off-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 6889125b8b4e09c5e53e6ecab3433bed1ce198c9 upstream.
powernowk8_target() runs off a per-cpu work item and if the
cpufreq_policy->cpu is different from the current one, it migrates the
kworker to the target CPU by manipulating current->cpus_allowed. The
function migrates the kworker back to the original CPU but this is
still broken. Workqueue concurrency management requires the kworkers
to stay on the same CPU and powernowk8_target() ends up triggerring
BUG_ON(rq != this_rq()) in try_to_wake_up_local() if it contends on
fidvid_mutex and sleeps.
It is unclear why this bug is being reported now. Duncan says it
appeared to be a regression of 3.6-rc1 and couldn't reproduce it on
3.5. Bisection seemed to point to 63d95a91 "workqueue: use @pool
instead of @gcwq or @cpu where applicable" which is an non-functional
change. Given that the reproduce case sometimes took upto days to
trigger, it's easy to be misled while bisecting. Maybe something made
contention on fidvid_mutex more likely? I don't know.
This patch fixes the bug by using work_on_cpu() instead if @pol->cpu
isn't the same as the current one. The code assumes that
cpufreq_policy->cpu is kept online by the caller, which Rafael tells
me is the case.
stable: ed48ece27c ("workqueue: reimplement work_on_cpu() using
system_wq") should be applied before this; otherwise, the
behavior could be horrible.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Duncan <1i5t5.duncan@cox.net>
Tested-by: Duncan <1i5t5.duncan@cox.net>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=47301
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 2453f5f992717251cfadab6184fbb3ec2f2e8b40 upstream.
If a command completes with a status of CMD_PROTOCOL_ERR, this
information should be conveyed to the SCSI mid layer, not dropped
on the floor. Unlike a similar bug in the hpsa driver, this bug
only affects tape drives and CD and DVD ROM drives in the cciss
driver, and to induce it, you have to disconnect (or damage) a
cable, so it is not a very likely scenario (which would explain
why the bug has gone undetected for the last 10 years.)
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 8dcebaa9a0ae8a0487f4342f3d56d2cb1c980860 upstream.
On some platforms, bootloaders are known to do some interesting RTC
programming. Without going into the obscurities as to why this may be
the case, suffice it to say the the driver should not make any
assumptions about the state of the RTC when the driver loads. In
particular, the driver probe should be sure that all interrupts are
disabled until otherwise programmed.
This was discovered when finding bursty I2C traffic every second on
Overo platforms. This I2C overhead was keeping the SoC from hitting
deep power states. The cause was found to be the RTC firing every
second on the I2C-connected TWL PMIC.
Special thanks to Felipe Balbi for suggesting to look for a rogue driver
as the source of the I2C traffic rather than the I2C driver itself.
Special thanks to Steve Sakoman for helping track down the source of the
continuous RTC interrups on the Overo boards.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Tested-by: Steve Sakoman <steve@sakoman.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Tested-by: Shubhrajyoti Datta <omaplinuxkernel@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit fded4e090c60100d709318896c79816d68d5b47d upstream.
Fix a serious but uncommon bug in nbd which occurs when there is heavy
I/O going to the nbd device while, at the same time, a failure (server,
network) or manual disconnect of the nbd connection occurs.
There is a small window between the time that the nbd_thread is stopped
and the socket is shutdown where requests can continue to be queued to
nbd's internal waiting_queue. When this happens, those requests are
never completed or freed.
The fix is to clear the waiting_queue on shutdown of the nbd device, in
the same way that the nbd request queue (queue_head) is already being
cleared.
Signed-off-by: Paul Clements <paul.clements@steeleye.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[bwh: Backported to 3.2: local nbd_device pointers are called 'lo' not 'nbd']
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 4c054ba63ad47ef244cfcfa1cea38134620a5bae upstream.
This patch fixes a long-standing bug with SCSI overflow handling
where se_cmd->data_length was incorrectly being re-assigned to
the larger CDB extracted allocation length, resulting in a number
of fabric level errors that would end up causing a session reset
in most cases. So instead now:
- Only re-assign se_cmd->data_length durining UNDERFLOW (to use the
smaller value)
- Use existing se_cmd->data_length for OVERFLOW (to use the smaller
value)
This fix has been tested with the following CDB to generate an
SCSI overflow:
sg_raw -r512 /dev/sdc 28 0 0 0 0 0 0 0 9 0
Tested using iscsi-target, tcm_qla2xxx, loopback and tcm_vhost fabric
ports. Here is a bit more detail on each case:
- iscsi-target: Bug with open-iscsi with overflow, sg_raw returns
-3584 bytes of data.
- tcm_qla2xxx: Working as expected, returnins 512 bytes of data
- loopback: sg_raw returns CHECK_CONDITION, from overflow rejection
in transport_generic_map_mem_to_cmd()
- tcm_vhost: Same as loopback
Reported-by: Roland Dreier <roland@purestorage.com>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 610bd7da160f76f1644ecb4cd7f39511b49a22cc upstream.
We noticed a plymouth bug on Fedora 18, and I then
noticed this stupid thinko, fixing it fixed the problem
with plymouth.
Acked-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 985f61f7ee647ad570c05eab0b74915da2ac8e19 upstream.
For DP we can use the same PPLL for all active DP
encoders. Take advantage of that to prevent cases
where we may end up sharing a PPLL between DP and
non-DP which won't work. Also clean up the code
a bit.
v2: - fix missing pll_id assignment in crtc init
v3: - fix DP PPLL check
- document functions
- break in main encoder search loop after matching.
no need to keep checking additional encoders.
fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=54471
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[bwh: Backported to 3.2: drop the DCE6 case]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit ecd67955fd4c8e66e4df312098989d5fa7da624c upstream.
No functional change, but re-order the cases so they
evaluate properly due to the way the DCE macros work.
Noticed by kallisti5 on IRC.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[bwh: Backported to 3.2: drop the DCE6 case]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 26fe45a0a76f165425f332a5aaa298f149f9db22 upstream.
Selecting ATOM_PPLL_INVALID should be equivalent as the
DCPLL or PPLL0 are already programmed for the DISPCLK, but
the preferred method is to always specify the PLL selected.
SetPixelClock will check the parameters and skip the
programming if the PLL is already set up.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
[bwh: Backported to 3.2: drop the DCE6 case]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 17c60c6b763cb5b83b0185e7d38d01d18e55a05a upstream.
This can also appear as 0x9192. Reported in bugzilla and confirmed with the
board documentation for these boards.
Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=42970
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 5e1782d224c79b26ab7d5c31e3f87657000714fb upstream.
Testing and works with the -modesetting driver,
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
