| Age | Commit message (Collapse) | Author |
|---|
|
commit 1152dcc28c66a74b5b3f1a3ede0aa6729bfd48e4 upstream
Similar to 6000 and 1000 series, RTS/CTS is the recommended protection
mechanism for 5000 series in HT mode based on the HW design.
Using RTS/CTS will better protect the inner exchange from interference,
especially in highly-congested environment, it also prevent uCode encounter
TX FIFO underrun and other HT mode related performance issues.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
upstream in 2.6.33-rc: 5d76b6f6c17572e662f5c99c2023adae92100855
Refreshed here for 2.6.32.y, applies w/ offset back to 2.6.29.y.
Linux has always ignored ACPI BIOS C2 with exit latency > 100 usec,
and the ACPI spec is clear that is correct FADT-supplied C2.
However, the ACPI spec explicitly states that _CST-supplied C-states
have no latency limits.
So move the 100usec C2 test out of the code shared
by FADT and _CST code-paths, and into the FADT-specific path.
This bug has not been visible until Nehalem, which advertises
a CPU-C2 worst case exit latency on servers of 205usec.
That (incorrect) figure is being used by BIOS writers
on mobile Nehalem systems for the AC configuration.
Thus, Linux ignores C2 leaving just C1, which is
saves less power, and also impacts performance
by preventing the use of turbo mode.
http://bugzilla.kernel.org/show_bug.cgi?id=15064
Tested-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 0cd4d0fd9b0a4e10c091fc6316d1bf92885dcd9c upstream.
IPoIB can miss a change in destination GID under some conditions. The
problem is caused when ipoib_neigh->dgid contains a stale address.
The fix is to set ipoib_neigh->dgid to zero in ipoib_neigh_alloc().
This can happen when a system using bonding on its IPoIB interfaces
has switched its active interface from interface A to B and back to A.
The system that fails over will not correctly processes the 2nd
address change, as described below.
When an address has changed neighbor->ha is updated with the new
address. Each neighbor has an associated ipoib_neigh.
ipoib_neigh->dgid also holds a copy of the remote node's hardware
address. When an address changes neighbor->ha is updated by the
network layer (arp code) with the new address. IPoIB detects this
change in ipoib_start_xmit() by comparing neighbor->ha with
ipoib_neigh->dgid. The bug is that ipoib_neigh->dgid may already
contain the new address (A) thus the change from B to A is missed by
ipoib. Here is the sequence of events:
ipoib_neigh->dgid = A and neighbor->ha = A
The address is switched to B (the first switch)
neighbor->ha = B
The change is seen in ipoib_start_xmit() -- neighbor->ha !=
ipoib_neigh->dgid so ipoib_neigh is released, and a new one is
allocated.
The allocator may return the same chunk of memory that was just
released, therefore ipoib_neigh->dgid still contains A at this point.
ipoib_neigh->dgid should be updated in neigh_add_path(), but if the
following conditions are true dgid is not updated:
1) __path_find() returns a path
2) path->ah is NULL
The remote system now switches from address B to A, neighbor->ha is
updated to A.
Now we have again : ipoib_neigh->dgid = A and neighbor->ha = A
Since the addresses are the same ipoib won't process the change in
address. Fix this by zeroing out the dgid field when allocating a new
struct ipoib_neigh.
Signed-off-by: David Wilder <dwilder@us.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit ff998793288b49a3b22d929bf8e56362320905ff upstream.
The in kernel copy of a volume's update marker is not initialised from the
volume table. This means that volumes where an update was unfinnished will
not be treated as "forbidden to use". This is basically that the update
functionality was broken.
Signed-off-by: Peter Horton <zero@colonel-panic.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit ebddd63b74dcf1cb676d14328d5852f1fee19a8a upstream.
When truncating an UBI volume, UBI should allocates a PEB-sized
buffer but does not release it, which leads to memory leaks.
This patch fixes the issue.
Reported-by: Marek Skuczynski <mareksk7@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Tested-by: Marek Skuczynski <mareksk7@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit c453615f77aa51593c1c9c9031b4278797d3fd19 upstream.
When /dev/watchdog gets opened a second time we return -EBUSY, but
we already have got a kref then, so we end up leaking our data struct.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 998221c26b86a7edd621e66b437628c5ec0f8e9b upstream.
tx_bytes value must be updated by skb length before skb is freed.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: John Jolly <jjolly@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 16b9a0571da4ee5cd15ca75e871722b0b5aee64d upstream.
Remove the call to BUG() for situations which are unexpected
but do not cause actual problems.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 48e4c385c5f54626651cca027afe242439281899 upstream.
io_subchannel_probe() frees memory for sch->private which is later
freed again when io_subchannel_remove() is called. Fix this problem
by removing the cleanup in io_subchannel_probe().
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 385097e08b9c24655626ed760bc67eb7e50115a0 upstream.
The control blacklisting code erroneously used usb_match_id() by passing
a pointer to a usb_device_id structure instead of an array of such
structures.
Replace the usb_match_id() call by usb_match_id_one().
Thanks to Paulo Assis for diagnosing the bug and providing an initial
fix.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 0f9552b5dc4fe10da37fa3f4a4ca185d90fa41c9 upstream.
The start_ro modules parameter can be used to force arrays to be
started in 'auto-readonly' in which they are read-only until the first
write. This ensures that no resync/recovery happens until something
else writes to the device. This is important for resume-from-disk
off an md array.
However if an array is started 'readonly' (by writing 'readonly' to
the 'array_state' sysfs attribute) we want it to be really 'readonly',
not 'auto-readonly'.
So strengthen the condition to only set auto-readonly if the
array is not already read-only.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 6938594374ee506e91a4c03117a034ea0ed66783 upstream.
Fix erroneous check for ap->udma_mask in do_pata_set_dmamode()
resulting in controller not being programmed properly for MWDMA.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 1b677afda44f7882b7e257d6f025d006ec5d14f9 upstream.
I obseved there is a sata_async_notification() for every ahci
interrupt. But the async notification does nothing (this is hard
disk drive and no pmp). This cause cpu wastes some time on sntf
register access.
It appears ICH AHCI doesn't support SNotification register, but the
controller reports it does. After quirking it, the async notification
disappears.
PS. it appears all ICH don't support SNotification register from ICH
manual, don't know if we need quirk all ICH. I don't have machines
with all kinds of ICH.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 3c9d8eccd8687f0e770e4d89fd0d73d4f81a985a upstream.
This patch adds the Intel Cougar Point and PCH DeviceIDs for iTCO Watchdog.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 4946f8353da9d3038e2a9d0295d5dfeee4cee5c5 upstream.
add PCI ID for the Intel EP80579 (Tolapai) SoC
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit cb711a1931363b8ad4dc98df4a92c262ced8eeb4 upstream.
Cleanup the documentation about the supported chipsets.
[needed for further device ids to add to this driver - gkh]
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit e6edbdc52bc0755cbfe0721ca91d4fd87649bc13 upstream.
Signed-off-by: Elliott Sales de Andrade <quantum.analyst@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit a61cd03827eceefcec19eefc6e1173703fdc5e5d upstream.
Gigabyte netbook model M1022M requires i8042.noloop, otherwise AUX port
will not detected and the touchpad will not work. Unfortunately chassis
type in DMI set to "Other" and thus generic laptop entry does not fire
on it.
Reported-by: Darryl Bond <dbond@nrggos.com.au>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit f909b1df0a068f30e252d8dc3e9d45ca25bf266f upstream.
The driver does not reference identification strings in DMI tables and
since these strings are no longer required by DMI core we can safely
remove them and save some memory.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 75757507e014fa074d25d2883c4ab604999584bd upstream.
The purpose of dmi->ident is twofold - it may be used by DMI callback
functions when composing log messages; it is also used to determine
end of DMI table in dmi_check_system() and dmi_first_match(). However,
in case when callbacks are not interested in using ident at all it just
wastes memory. Let's make entries with empty first match slot serve as
end-of-table markers instead.
[needed for DMI table changes that need to be done by later patches - gkh]
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 46256f83d0d066f99ffde547f27473dfd2a78009 upstream.
If the BIOS does not export _OSC to allow OS take over the PCIe AER, the
pcie aer driver will not initialize the aer service. However, the
aer_inject driver does not check this scenario, which results in a kernel
oops when injecting an aer error into OS. For example:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000350
IP: [<ffffffff812e08f7>] _spin_lock_irqsave+0xc/0x23
PGD 155c41067 PUD 157fe0067 PMD 0
Oops: 0002 [#1] SMP
Pid: 5119, comm: aer-inject Not tainted 2.6.32-rc8-mce #2
RIP: 0010:[<ffffffff812e08f7>] [<ffffffff812e08f7>] _spin_lock_irqsave+0xc/0x23
RSP: 0018:ffff880157f81e28 EFLAGS: 00010096
RAX: 0000000000000296 RBX: 0000000000000000 RCX: 0000000000000100
RDX: 0000000000010000 RSI: 0000000000000246 RDI: 0000000000000350
RBP: ffff880157f81e28 R08: 0000000000000004 R09: ffff880157f81dac
R10: ffff88015a666f60 R11: ffff88015a666f40 R12: ffff88015758cc00
R13: 0000000000000350 R14: 0000000000000000 R15: 0000000000000100
FS: 00007f4d4a66e6f0(0000) GS:ffff8800282e0000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 0000000000000350 CR3: 000000015661a000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process aer-inject (pid: 5119, threadinfo ffff880157f80000, task ffff8801585f4340)
Stack:
ffff880157f81e78 ffffffff811b1615 ffff880157f81e78 ffffffff81222823
Call Trace:
[<ffffffff811b1615>] aer_irq+0x38/0x117
[<ffffffff81222823>] ? device_for_each_child+0x5f/0x6f
[<ffffffffa00967bf>] aer_inject_write+0x409/0x45e [aer_inject]
[<ffffffff810eb80e>] vfs_write+0xae/0x16a
[<ffffffff810eb98e>] sys_write+0x47/0x6e
[<ffffffff8100ba2b>] system_call_fastpath+0x16/0x1b
RIP [<ffffffff812e08f7>] _spin_lock_irqsave+0xc/0x23
RSP <ffff880157f81e28>
CR2: 0000000000000350
So check the _OSC before assuming that AER is available to the OS.
Signed-off-by: Song Youquan <youquan.song@intel.com>
Acked-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 63ae93a19094d88c8ca62543586b20e3a7ff7637 upstream.
Allow MAC address to be changed even if device is not up.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 91ced682f9de17ebab5fcb2a70b48e372eb43281 upstream.
The driver has nothing to do, but this marker prevents the event from
showing up 'not handled'.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 80928860941023bb37e9c61927395d0eb753bc3b upstream.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit bc9167f39ff8cd428e8577eb72751a653008edb2 upstream.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 1d1023d039d8295070b8dbb92c4d972237235304 upstream.
Remove explicit setting of error reporting bits.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 5bab87e6d465d54a2b5899e0f583d42f00dbee2e upstream.
Make sure we are get the SAN MAC address from the real netdev if the input
netdev is a VLAN device.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit bf361707c81f8e8e43e332bfc8838bae76ae021a upstream.
This was fixed before in 7a7f0c7 but it's introduced again recently.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 14caf44c69184ed72d46a2f883311daf27a4192f upstream.
The cmd_per_lun value is used by scsi-ml as fall back lowest
queue_depth value but in case of libfc cmd_per_lun is set to
same value as max queue_depth = 32.
So this patch reduces cmd_per_lun value to 3 and configures
each lun with default max queue_depth 32 in fc_slave_alloc.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Acked-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 5543c72e2bbb30e5ba5938b18ec26617b8b3fb04 upstream.
We ran into a scenario where a remote port goes into RESTART state, but
never gets added to scsi transport. The running vmcore showed the following:
a) Port was in RESTART state
b) rdata->event was STOP
c) no work gets scheduled for the remote work to fc_rport_work
After this point, shut/no-shut of the remote port did not cause the port
to get re-discovered. The port would move betwen DELETE and RESTART states,
but the event would always be STOP, no work would get scheduled to
fc_rport_work and the port would not get added to scsi_transport.
The problem is that rdata->event is not set to NONE after a port is
restarted. After this point, no more work gets scheduled for the remote port
since new work is scheduled only if rdata->event is non-NONE. So, the event
and state keep changing, but fc_rport_work does not get scheduled to actually
handle the event.
Here's a transition of states that explains the above observation:
) Port is first in READY State, event is NONE
2) RSCN on shut, port goes to DELETED, event is stop
3) Before fc_rport_work runs, RSCN on no-shut, port goes to RESTART, event is
still STOP
4) fc_rport_work gets scheduled, removes the port from transport, sees state
as RESTART, begins the PLOGI state machine, event remains as STOP (event NOT
changed to NONE, this is the bug)
5) Plogi state machine completes, port state goes to READY, event goes to
READY, but no work is scheduled since event was STOP (non-NONE) before.
Fc_rport_work is not scheduled, port remains in READY state, but is not added
to transport.
Things are broken at this point. Libfc rport is ready, but no transport rport
created.
6) now a shut causes port state to change to DELETE, event to change to STOP,
no work gets scheduled
7) no-shut causes port state to change to RESTART, event remains at STOP,
no work gets scheduled
(6) and (7) now get repeated everytime we do shut/no-shut. No way to get out
of this state. Fcc reset does not help too.
Only way to get out is to load/unload module.
Fix is to set rdata->event to NONE while processing the STOP/LOGO/FAILED
events, inside the discovery and rport locks.
Signed-off-by: Abhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit b4a9c7ede96e90f7b1ec009ce7256059295e76df upstream.
Timer crashes were caused by freeing a struct fc_rport_priv
with a timer pending, causing the timer facility list to be
corrupted. This was during FC uplink flap tests with a lot
of targets.
After discovery, we were doing an PLOGI on an rdata that was
in DELETE state but not yet removed from the lookup list.
This moved the rdata from DELETE state to PLOGI state.
If the PLOGI exchange allocation failed and needed to be
retried, the timer scheduling could race with the free
being done by fc_rport_work().
When fc_rport_login() is called on a rport in DELETE state,
move it to a new state RESTART. In fc_rport_work, when
handling a LOGO, STOPPED or FAILED event, look for restart
state. In the RESTART case, don't take the rdata off the
list and after the transport remote port is deleted and
exchanges are reset, re-login to the remote port.
Note that the new RESTART state also corrects a problem we
had when re-discovering a port that had moved to DELETE state.
In that case, a new rdata was created, but the old rdata
would do an exchange manager reset affecting the FC_ID
for both the new rdata and old rdata. With the new state,
the new port isn't logged into until after any old exchanges
are reset.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 8f550f937e9fdafa5c37e348e214aecec851ef3f upstream.
I was running into several different panics under stress, which I traced down
to a few different possible slab corruption issues in error handling paths.
I have not yet looked into why these exchange sends fail, but with these
fixes my test system is much more stable under stress than before.
fc_elsct_send() could fail and either leave the passed in frame intact
(failure in fc_ct/els_fill) or the frame could have been freed if the
failure was is fc_exch_seq_send(). The caller had no way of knowing, and
there was a potential double free in the error handling in fc_fcp_rec().
Make fc_elsct_send() always free the frame before returning, and remove the
fc_frame_free() call in fc_fcp_rec().
While fc_exch_seq_send() did always consume the frame, there were double free
bugs in the error handling of fc_fcp_cmd_send() and fc_fcp_srr() as well.
Numerous calls to error handling routines (fc_disc_error(),
fc_lport_error(), fc_rport_error_retry() ) were passing in a frame pointer that
had already been freed in the case of an error. I have changed the call
sites to pass in a NULL pointer, but there may be more appropriate error
codes to use.
Question: Why do these error routines take a frame pointer anyway? I
understand passing in a pointer encoded error to the response handlers, but
the error routines take no action on a valid pointer and should never be
called that way.
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit d37322a43ebac79eef417149f5696390cf8872db upstream.
In case of sequence offload, in fc_fcp_send_data(), the skb_fill_page_info()
called may end up adding more frags to the skb_shinfo(fp_skb(fp))->frags[],
exceeding SKB_MAX_FRAGS, this eventually corrupts the memory. I am adding the
FR_FRAME_SG_LEN back, but as SKB_MAX_FRAGS -1, leaving 1 for our fcoe_eof_crc
page. And send will be broken into multiple large sends if the frame already
contains more frags than skb handle.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 8eca355fa8af660557fbdd5506bde1392eee9bfe upstream.
When doing echo ethX > /sys..../destroy I am getting
errors when the tear down succeeds. It looks like the
reason for this is because the rc var is not getting set
when the destruction works. This just sets it to zero.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 22655ac22289d7b7def8ef2d72eafe5024bd57fe upstream.
It's possible and harmless to get FLOGI timeouts
while in RESET state. Don't do a WARN_ON in that case.
Also, split out the other WARN_ONs in fc_lport_timeout, so
we can tell which one is hit by its line number.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 1b69bc062c2a4c8f3e15ac69f487afec3aa8d774 upstream.
Fix minor errors.
A debug message said an RLIR was received instead of ECHO.
"Expected" was misspelled in several places.
Fix a type cast from u32 to __be32.
Rob, Some of these may have been also taken care of in your
other doc cleanup patch. Feel free to fold them in.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 4347fa66878e079766258bc0d077c350cb31a799 upstream.
This bug is exposed when there is a link flap in LLD. Particularly, when it
happens right after a SCSI write command is sent out, no FCP_DATA is sent,
causing fsp->status_code to be set as FC_DATA_UNDRUN in fc_fcp_complete_locked
even no SCSI status is received. Consequently, fc_io_compl treats this as DID_OK.
This results in SCSI returning successful to the initial I/O request even
there is no DATA actually sent. Particularly, if you run an I/O tool w/ data
verification on, the read back for verification is gonna fail.
This is fixed here by checking when FC_DATA_UNDRUN happens, SCSI status is
received w/ FC_SRB_RCV_STATUS set in fsp->state.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit b04d023cf5b7f4113cc4a09405c2fe8003bfe37d upstream.
Remove the redundant checking of netdev->netdev_ops as it will never be NULL.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 5e472d077f45de4f37365171bd742f18b3ef20de upstream.
xid 0 was used as an indication of invalid xid before but now xid 0
can be used as a valid exchange i. This patch fixes the ddp completion
in fcp layer, i.e., in fc_fcp.c:fc_fcp_ddp_done() function, to make sure it
does not use xid 0 for indication of an invalid xid, instead, it now
uses use FC_XID_UNKNOWN for such indication.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 85b5893ca97c69e409ecbb5ee90a5d99882369c4 upstream.
A received Fibre Channel ELS PRLI request contains a bit that
indicates whether the remote port supports certain retry processing
sequences. The test for this bit was somehow coded to use multiply
instead of AND!
This case would apply only for target mode operation, and it is
unlikely to be noticed as an initiator.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 8e68597d087977d3e4fd3e735d290ab45fd0b5ea upstream.
In testing 2.6.31 on one of our ia64 platforms I've encountered a hang
due to the driver using hardware ATEs which are a limited resource.
This is because the driver does not set the dma consistent mask to
64 bits.
Signed-off-by: Michael Reed <mdr@sgi.com>
Acked-by: James Smart <James.Smart@Emulex.Com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 8798a694da59486e4a3ff0abeec183202fb34c20 upstream.
I was doing some large lun count testing with 2.6.31 and hit
a BUG_ON() in fc_timeout_deleted_rport(), and it seems like it
should have been just a matter of time before someone did.
It seems invalid to set port_state under lock, then expect it to
remain set after releasing the lock. Another thread called
fc_remote_port_add() when the lock was released, changing the
port_state.
This patch removes the BUG_ON and moves the test of the
port_state to inside the host_lock. It's been running for
several weeks now with no ill effect.
Signed-off-by: Michael Reed <mdr@sgi.com>
Acked-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 5917290ce9b376866b165d02a5ed88d5ecdb32d0 upstream.
Create the sysfs file, dh_state even if the new SCSI device is not
in the any of the device handler's internal lists.
Signed-Off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 627511e3e67553b04f6917c03e39b797df210e04 upstream.
Four models, OPEN-/DF400/DF500/DISK-SUBSYSTEM, can handle REPORT_LUN,
and the BLIST_REPORTLUN2 flag needs to be set. And DF600 doesn't require
any flags because it returns ANSI 03h (SPC).
Signed-off-by: Takahiro Yasui <tyasui@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 5b915d9e6dc3d22fedde91dfef1cb1a8fa9a1870 upstream.
NCR devices are terminally broken by design -- they claim themselves to contain
proper input applications in their HID report descriptor, but behave very badly
if treated in standard way.
According to NCR developers, the devices get confused when queried for reports
in a standard way, rendering them unusable.
NCR is shipping application called "RPSL" that can be used to drive these
devices through hiddev, under the assumption that in-kernel driver doesn't
perform initial report query.
If it does, neither in-kernel nor hiddev-based driver can operate with these
devices any more.
Introduce a quirk that skips the report query for all NCR devices. The previous
NOGET quirk was wrong and had been introduced because I misunderstood the nature
of brokenness of these devices.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit fdd46dcbe4468a1f47a2cc9be442d11c3d21dd68 upstream.
This patch modifies the replacement/recovery_timeout so it works
more like the fc fast io fail tmo.
If userspace tries to set the replacement/recovery_timeout to less than
zero, we will turn off the forced recovery cleanup.
If userspace sets the value to 0 then we will force the recovery
cleanup immediately.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 59353ea30e65ab3ae181d6175e3212e1361c3787 upstream.
Prior to 1f82de10 we always initialized the upper 32bits of the
prefetchable memory window, regardless of the address range used.
Now we only touch it for a >32bit address, which means the upper32
registers remain whatever the BIOS initialized them too.
It's valid for the BIOS to set the upper32 base/limit to
0xffffffff/0x00000000, which makes us program prefetchable ranges
like 0xffffffffabc00000 - 0x00000000abc00000
Revert the chunk of 1f82de10 that made this conditional so we always
write the upper32 registers and remove now unused pref_mem64 variable.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Rafael J. Wysocki <rjw@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 7c7afb083675b3d4d012a2aacec3a958ba484ab0 upstream.
For hardware limit to support TSOV6, just disable this feature
Signed-off-by: Jie Yang <jie.yang@atheros.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit cb19054697e92a793f336380fd72c588521178ff upstream.
use common_task instead of reset_task and link_chg_task, so it fix "call cancel_work_sync
from the work itself".
Signed-off-by: Jie Yang <jie.yang@atheros.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 79e8941dda254505bb8af37b3a009165dfb7e98a upstream.
Add the Intel Ibex Peak (PCH) Device IDs to iTCO_wdt.c.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
