| Age | Commit message (Collapse) | Author |
|---|
|
commit b5a3b3d985493c173925907adfebf3edab236fe7 upstream.
This patch (as1453) fixes a long-standing bug in the ehci-hcd driver.
There is no need to set the Halt bit in the overlay region for an
unlinked or blocked QH. Contrary to what the comment says, setting
the Halt bit does not cause the QH to be patched later; that decision
(made in qh_refresh()) depends only on whether the QH is currently
pointing to a valid qTD. Likewise, setting the Halt bit does not
prevent completions from activating the QH while it is "stopped"; they
are prevented by the fact that qh_completions() temporarily changes
qh->qh_state to QH_STATE_COMPLETING.
On the other hand, there are circumstances in which the QH will be
reactivated _without_ being patched; this happens after an URB beyond
the head of the queue is unlinked. Setting the Halt bit will then
cause the hardware to see the QH with both the Active and Halt bits
set, an invalid combination that will prevent the queue from
advancing and may even crash some controllers.
Apparently the only reason this hasn't been reported before is that
unlinking URBs from the middle of a running queue is quite uncommon.
However Test 17, recently added to the usbtest driver, does exactly
this, and it confirms the presence of the bug.
In short, there is no reason to set the Halt bit for an unlinked or
blocked QH, and there is a very good reason not to set it. Therefore
the code that sets it is removed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Andiry Xu <andiry.xu@amd.com>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit d6244bc0ed0c52a795e6f4dcab3886daf3e74fac upstream.
Use mask 0x10 for "soft cursor" detection on in function tile_cursor.
(Tile Blitting Operation in framebuffer console).
The old mask 0x01 for vc_cursor_type detects CUR_NONE, CUR_LOWER_THIRD
and every second mode value as "software cursor". This hides the cursor
for these modes (cursor.mode = 0). But, only CUR_NONE or "software cursor"
should hide the cursor.
See also 0x10 in functions add_softcursor, bit_cursor and cw_cursor.
Signed-off-by: Henry Nestler <henry.nestler@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit bc10f96757bd6ab3721510df8defa8f21c32f974 upstream.
Remove the call to tty_ldisc_flush() from the RESULT_NO_CARRIER
branch of isdn_tty_modem_result(), as already proposed in commit
00409bb045887ec5e7b9e351bc080c38ab6bfd33.
This avoids a "sleeping function called from invalid context" BUG
when the hardware driver calls the statcallb() callback with
command==ISDN_STAT_DHUP in atomic context, which in turn calls
isdn_tty_modem_result(RESULT_NO_CARRIER, ~), and from there,
tty_ldisc_flush() which may sleep.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 87e3dc3855430bd254370afc79f2ed92250f5b7c upstream.
Some broken BIOSes on ICH4 chipset report an ACPI region which is in
conflict with legacy IDE ports when ACPI is disabled. Even though the
regions overlap, IDE ports are working correctly (we cannot find out
the decoding rules on chipsets).
So the only problem is the reported region itself, if we don't reserve
the region in the quirk everything works as expected.
This patch avoids reserving any quirk regions below PCIBIOS_MIN_IO
which is 0x1000. Some regions might be (and are by a fast google
query) below this border, but the only difference is that they won't
be reserved anymore. They should still work though the same as before.
The conflicts look like (1f.0 is bridge, 1f.1 is IDE ctrl):
pci 0000:00:1f.1: address space collision: [io 0x0170-0x0177] conflicts with 0000:00:1f.0 [io 0x0100-0x017f]
At 0x0100 a 128 bytes long ACPI region is reported in the quirk for
ICH4. ata_piix then fails to find disks because the IDE legacy ports
are zeroed:
ata_piix 0000:00:1f.1: device not available (can't reserve [io 0x0000-0x0007])
References: https://bugzilla.novell.com/show_bug.cgi?id=558740
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Renninger <trenn@suse.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit cdb9755849fbaf2bb9c0a009ba5baa817a0f152d upstream.
Per ICH4 and ICH6 specs, ACPI and GPIO regions are valid iff ACPI_EN
and GPIO_EN bits are set to 1. Add checks for these bits into the
quirks prior to the region creation.
While at it, name the constants by macros.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Renninger <trenn@suse.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit d0781383038e983a63843a9a6a067ed781db89c1 upstream.
I picked up a new DAK-780EX(professional digitl reverb/mix system),
which use CH341T chipset to communication with computer on 3/2011
and the CH341T's vendor code is 1a86
Looking up the CH341T's vendor and product id's I see:
1a86 QinHeng Electronics
5523 CH341 in serial mode, usb to serial port converter
CH341T,CH341 are the products of the same company, maybe
have some common hardware, and I test the ch341.c works
well with CH341T
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 29963437a48475036353b95ab142bf199adb909e upstream.
When processing a SIDR REQ, the ib_cm allocates a new cm_id. The
refcount of the cm_id is initialized to 1. However, cm_process_work
will decrement the refcount after invoking all callbacks. The result
is that the cm_id will end up with refcount set to 0 by the end of the
sidr req handler.
If a user tries to destroy the cm_id, the destruction will proceed,
under the incorrect assumption that no other threads are referencing
the cm_id. This can lead to a crash when the cm callback thread tries
to access the cm_id.
This problem was noticed as part of a larger investigation with kernel
crashes in the rdma_cm when running on a real time OS.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Acked-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 25ae21a10112875763c18b385624df713a288a05 upstream.
Doug Ledford and Red Hat reported a crash when running the rdma_cm on
a real-time OS. The crash has the following call trace:
cm_process_work
cma_req_handler
cma_disable_callback
rdma_create_id
kzalloc
init_completion
cma_get_net_info
cma_save_net_info
cma_any_addr
cma_zero_addr
rdma_translate_ip
rdma_copy_addr
cma_acquire_dev
rdma_addr_get_sgid
ib_find_cached_gid
cma_attach_to_dev
ucma_event_handler
kzalloc
ib_copy_ah_attr_to_user
cma_comp
[ preempted ]
cma_write
copy_from_user
ucma_destroy_id
copy_from_user
_ucma_find_context
ucma_put_ctx
ucma_free_ctx
rdma_destroy_id
cma_exch
cma_cancel_operation
rdma_node_get_transport
rt_mutex_slowunlock
bad_area_nosemaphore
oops_enter
They were able to reproduce the crash multiple times with the
following details:
Crash seems to always happen on the:
mutex_unlock(&conn_id->handler_mutex);
as conn_id looks to have been freed during this code path.
An examination of the code shows that a race exists in the request
handlers. When a new connection request is received, the rdma_cm
allocates a new connection identifier. This identifier has a single
reference count on it. If a user calls rdma_destroy_id() from another
thread after receiving a callback, rdma_destroy_id will proceed to
destroy the id and free the associated memory. However, the request
handlers may still be in the process of running. When control returns
to the request handlers, they can attempt to access the newly created
identifiers.
Fix this by holding a reference on the newly created rdma_cm_id until
the request handler is through accessing it.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Acked-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 64a3903d0885879ba8706a8bcf71c5e3e7664db2 upstream.
This patch adds an updated SATA RAID DeviceID for the Intel Patsburg PCH.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit a4a461a6df6c0481d5a3d61660ed97f5b539cf16 upstream.
This patch adds the AHCI-mode SATA DeviceID for the Intel DH89xxCC PCH.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 992b3fb9b5391bc4de5b42bb810dc6dd583a6c4a upstream.
This patch adds the Intel Patsburg (PCH) SATA AHCI and RAID Controller
DeviceIDs.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 5623cab83ea61e0420f2064216d83eab067a24c6 upstream.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
commit c1f57d9b9846e7366c328f916d1a82d03ba4312c upstream.
Add device IDS for Ibex Peak SATA AHCI Controllers
Signed-off-by: Jaroslav Kysela <jkysela@redhat.com>
Signed-off-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
commit f08dc1ac6b15c681f4643d8da1700e06c3855608 upstream.
ata_qc_complete() contains special handling for certain commands. For
example, it schedules EH for device revalidation after certain
configurations are changed. These shouldn't be applied to EH
commands but they were.
In most cases, it doesn't cause an actual problem because EH doesn't
issue any command which would trigger special handling; however, ACPI
can issue such commands via _GTF which can cause weird interactions.
Restructure ata_qc_complete() such that EH commands are always passed
on to __ata_qc_complete().
stable: Please apply to -stable only after 2.6.38 is released.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit d9ebaa45472c92704f4814682eec21455edcfa1f upstream.
This avoids a possible race leading to trying to dereference NULL.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit b652277b09d3d030cb074cc6a98ba80b34244c03 upstream.
The "ct" variable should be an unsigned int. Both struct kbdiacrs
->kb_cnt and struct kbd_data ->accent_table_size are unsigned ints.
Making it signed causes a problem in KBDIACRUC because the user could
set the signed bit and cause a buffer overflow.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 3ed780117dbe5acb64280d218f0347f238dafed0 upstream.
If the iowarrior devices in this case statement support more than 8 bytes
per report, it is possible to write past the end of a kernel heap allocation.
This will probably never be possible, but change the allocation to be more
defensive anyway.
Signed-off-by: Kees Cook <kees.cook@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Brandon Philips <bphilips@suse.de>
|
|
commit ba04c7c93bbcb48ce880cf75b6e9dffcd79d4c7b upstream.
For some time is known that ASPM is causing troubles on r8169, i.e. make
device randomly stop working without any errors in dmesg.
Currently Tomi Leppikangas reports that system with r8169 device hangs
with MCE errors when ASPM is enabled:
https://bugzilla.redhat.com/show_bug.cgi?id=642861#c4
Lets disable ASPM for r8169 devices at all, to avoid problems with
r8169 PCIe devices at least for some users.
Reported-by: Tomi Leppikangas <tomi.leppikangas@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit bc505f373979692d51a86d40925f77a8b09d17b9 upstream.
As all virtio devices perform DMA, we
must enable bus mastering for them to be
spec compliant.
This patch fixes hotplug of virtio devices
with Linux guests and qemu 0.11-0.12.
Tested-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Cc: maximilian attems <max@stro.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 9063f1f15eec35e5fd608879cef8be5728f2d12a upstream.
Call input_set_abs_params instead of manually setting absbit only.
This fixes this oops:
Unable to handle kernel NULL pointer dereference at virtual address 00000024
Internal error: Oops: 41b67017 [#1]
CPU: 0 Not tainted (2.6.37 #4)
pc : [<c016d1fc>] lr : [<00000000>] psr: 20000093
sp : c19e5f30 ip : c19e5e6c fp : c19e5f58
r10: 00000000 r9 : c19e4000 r8 : 00000003
r7 : 000001e4 r6 : 00000001 r5 : c1854400 r4 : 00000003
r3 : 00000018 r2 : 00000018 r1 : 00000018 r0 : c185447c
Flags: nzCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel
Control: c1b6717f Table: c1b6717f DAC: 00000017
Stack: (0xc19e5f30 to 0xc19e6000)
5f20: 00000003 00000003 c1854400 00000013
5f40: 00000001 000001e4 000001c5 c19e5f80 c19e5f5c c016d5e8 c016cf5c 000001e4
5f60: c1854400 c18b5860 00000000 00000171 000001e4 c19e5fc4 c19e5f84 c01559a4
5f80: c016d584 c18b5868 00000000 c1bb5c40 c0035afc c18b5868 c18b5868 c1a55d54
5fa0: c18b5860 c0155750 00000013 00000000 00000000 00000000 c19e5ff4 c19e5fc8
5fc0: c0050174 c015575c 00000000 c18b5860 00000000 c19e5fd4 c19e5fd4 c1a55d54
5fe0: c00500f0 c003b464 00000000 c19e5ff8 c003b464 c00500fc 04000400 04000400
Backtrace:
Function entered at [<c016cf50>] from [<c016d5e8>]
Function entered at [<c016d578>] from [<c01559a4>]
r8:000001e4 r7:00000171 r6:00000000 r5:c18b5860 r4:c1854400
Function entered at [<c0155750>] from [<c0050174>]
Function entered at [<c00500f0>] from [<c003b464>]
r6:c003b464 r5:c00500f0 r4:c1a55d54
Code: e59520fc e1a03286 e0433186 e0822003 (e592000c)
>>PC; c016d1fc <input_handle_event+2ac/5a0> <=====
Trace; c016cf50 <input_handle_event+0/5a0>
Trace; c016d5e8 <input_event+70/88>
Trace; c016d578 <input_event+0/88>
Trace; c01559a4 <ucb1x00_thread+254/2dc>
Trace; c0155750 <ucb1x00_thread+0/2dc>
Trace; c0050174 <kthread+84/8c>
Trace; c00500f0 <kthread+0/8c>
Trace; c003b464 <do_exit+0/624>
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 8f5f02c460b7ca74ce55ce126ce0c1e58a3f923d upstream.
'mdp' devices are md devices with preallocated device numbers
for partitions. As such it is possible to mknod and open a partition
before opening the whole device.
this causes md_probe() to be called with a device number of a
partition, which in-turn calls mddev_find with such a number.
However mddev_find expects the number of a 'whole device' and
does the wrong thing with partition numbers.
So add code to mddev_find to remove the 'partition' part of
a device number and just work with the 'whole device'.
This patch addresses https://bugzilla.kernel.org/show_bug.cgi?id=28652
Reported-by: hkmaly@bigfoot.com
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit b193b412e62b134adf69af286c7e7f8e99259350 upstream.
Cancel idle timer in musb_platform_exit.
The idle timer could trigger after clock had been disabled leading to
kernel panic when MUSB_DEVCTL is accessed in musb_do_idle on 2.6.37.
The fault below is no longer triggered on 2.6.38-rc4 (clock is disabled
later, and only if compiled as a module, and the offending memory access
has moved) but the timer should be cancelled nonetheless.
Rebooting... musb_hdrc musb_hdrc: remove, state 4
usb usb1: USB disconnect, address 1
musb_hdrc musb_hdrc: USB bus 1 deregistered
Unhandled fault: external abort on non-linefetch (0x1028) at 0xfa0ab060
Internal error: : 1028 [#1] PREEMPT
last sysfs file: /sys/kernel/uevent_seqnum
Modules linked in:
CPU: 0 Not tainted (2.6.37+ #6)
PC is at musb_do_idle+0x24/0x138
LR is at musb_do_idle+0x18/0x138
pc : [<c02377d8>] lr : [<c02377cc>] psr: 80000193
sp : cf2bdd80 ip : cf2bdd80 fp : c048a20c
r10: c048a60c r9 : c048a40c r8 : cf85e110
r7 : cf2bc000 r6 : 40000113 r5 : c0489800 r4 : cf85e110
r3 : 00000004 r2 : 00000006 r1 : fa0ab000 r0 : cf8a7000
Flags: Nzcv IRQs off FIQs on Mode SVC_32 ISA ARM Segment user
Control: 10c5387d Table: 8faac019 DAC: 00000015
Process reboot (pid: 769, stack limit = 0xcf2bc2f0)
Stack: (0xcf2bdd80 to 0xcf2be000)
dd80: 00000103 c0489800 c02377b4 c005fa34 00000555 c0071a8c c04a3858 cf2bdda8
dda0: 00000555 c048a00c cf2bdda8 cf2bdda8 1838beb0 00000103 00000004 cf2bc000
ddc0: 00000001 00000001 c04896c8 0000000a 00000000 c005ac14 00000001 c003f32c
dde0: 00000000 00000025 00000000 cf2bc000 00000002 00000001 cf2bc000 00000000
de00: 00000001 c005ad08 cf2bc000 c002e07c c03ec039 ffffffff fa200000 c0033608
de20: 00000001 00000000 cf852c14 cf81f200 c045b714 c045b708 cf2bc000 c04a37e8
de40: c0033c04 cf2bc000 00000000 00000001 cf2bde68 cf2bde68 c01c3abc c004f7d8
de60: 60000013 ffffffff c0033c04 00000000 01234567 fee1dead 00000000 c006627c
de80: 00000001 c00662c8 28121969 c00663ec cfa38c40 cf9f6a00 cf2bded0 cf9f6a0c
dea0: 00000000 cf92f000 00008914 c02cd284 c04a55c8 c028b398 c00715c0 becf24a8
dec0: 30687465 00000000 00000000 00000000 00000002 1301a8c0 00000000 00000000
dee0: 00000002 1301a8c0 00000000 00000000 c0450494 cf527920 00011f10 cf2bdf08
df00: 00011f10 cf2bdf10 00011f10 cf2bdf18 c00f0b44 c004f7e8 cf2bdf18 cf2bdf18
df20: 00011f10 cf2bdf30 00011f10 cf2bdf38 cf401300 cf486100 00000008 c00d2b28
df40: 00011f10 cf401300 00200200 c00d3388 00011f10 cfb63a88 cfb63a80 c00c2f08
df60: 00000000 00000000 cfb63a80 00000000 cf0a3480 00000006 c0033c04 cfb63a80
df80: 00000000 c00c0104 00000003 cf0a3480 cfb63a80 00000000 00000001 00000004
dfa0: 00000058 c0033a80 00000000 00000001 fee1dead 28121969 01234567 00000000
dfc0: 00000000 00000001 00000004 00000058 00000001 00000001 00000000 00000001
dfe0: 4024d200 becf2cb0 00009210 4024d218 60000010 fee1dead 00000000 00000000
[<c02377d8>] (musb_do_idle+0x24/0x138) from [<c005fa34>] (run_timer_softirq+0x1a8/0x26)
[<c005fa34>] (run_timer_softirq+0x1a8/0x26c) from [<c005ac14>] (__do_softirq+0x88/0x13)
[<c005ac14>] (__do_softirq+0x88/0x138) from [<c005ad08>] (irq_exit+0x44/0x98)
[<c005ad08>] (irq_exit+0x44/0x98) from [<c002e07c>] (asm_do_IRQ+0x7c/0xa0)
[<c002e07c>] (asm_do_IRQ+0x7c/0xa0) from [<c0033608>] (__irq_svc+0x48/0xa8)
Exception stack(0xcf2bde20 to 0xcf2bde68)
de20: 00000001 00000000 cf852c14 cf81f200 c045b714 c045b708 cf2bc000 c04a37e8
de40: c0033c04 cf2bc000 00000000 00000001 cf2bde68 cf2bde68 c01c3abc c004f7d8
de60: 60000013 ffffffff
[<c0033608>] (__irq_svc+0x48/0xa8) from [<c004f7d8>] (sub_preempt_count+0x0/0xb8)
Code: ebf86030 e5940098 e594108c e5902010 (e5d13060)
---[ end trace 3689c0d808f9bf7c ]---
Kernel panic - not syncing: Fatal exception in interrupt
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 8a6a142c1286797978e4db266d22875a5f424897 upstream.
Don't allow everybody to change WMI settings.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit b80b168f918bba4b847e884492415546b340e19d upstream.
Don't allow everybody to write to hardware registers.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[wt: also fixed permission on interface]
|
|
commit 8040835760adf0ef66876c063d47f79f015fb55d upstream.
Don't allow everybody to change ACPI settings. The comment says that it
is done deliberatelly, however, the comment before disp_proc_write()
says that at least one of these setting is experimental.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 2400982a2e8a8e4e95f0a0e1517bbe63cc88038f upstream.
Commit e3c92215198cb6aa00ad38db2780faa6b72e0a3f ("[media] radio-aimslab.c: Fix
gcc 4.5+ bug") removed the include, but introduced new callers of msleep():
| drivers/media/radio/radio-aimslab.c: In function ‘rt_decvol’:
| drivers/media/radio/radio-aimslab.c:76: error: implicit declaration of function ‘msleep’
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: dann frazier <dannf@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 5528d17de1cf1462f285c40ccaf8e0d0e4c64dc0 upstream.
If the mirror log fails when the handle_errors option was not selected
and there is no remaining valid mirror leg, writes return success even
though they weren't actually written to any device. This patch
completes them with EIO instead.
This code path is taken:
do_writes:
bio_list_merge(&ms->failures, &sync);
do_failures:
if (!get_valid_mirror(ms)) (false)
else if (errors_handled(ms)) (false)
else bio_endio(bio, 0);
The logic in do_failures is based on presuming that the write was already
tried: if it succeeded at least on one leg (without handle_errors) it
is reported as success.
Reference: https://bugzilla.redhat.com/show_bug.cgi?id=555197
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: maximilian attems <max@stro.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 40f08a724fcc21285cf3a75aec957aef908605c6 upstream.
Abusing irq stats in a driver for counting interrupts is a horrible
idea and not safe with shared interrupts. Replace it by a local
interrupt counter.
Noticed by the attempt to remove the irq stats export.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Cc: maximilian attems <max@stro.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit cb26a24ee9706473f31d34cc259f4dcf45cd0644 upstream.
info->num comes from the user. It's type int. If the user passes
in a negative value that would cause memory corruption.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 252a52aa4fa22a668f019e55b3aac3ff71ec1c29 upstream.
The PKT_CTRL_CMD_STATUS device ioctl retrieves a pointer to a
pktcdvd_device from the global pkt_devs array. The index into this
array is provided directly by the user and is a signed integer, so the
comparison to ensure that it falls within the bounds of this array will
fail when provided with a negative index.
This can be used to read arbitrary kernel memory or cause a crash due to
an invalid pointer dereference. This can be exploited by users with
permission to open /dev/pktcdvd/control (on many distributions, this is
readable by group "cdrom").
Signed-off-by: Dan Rosenberg <dan.j.rosenberg@gmail.com>
[ Rather than add a cast, just make the function take the right type -Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit c4ff4b829ef9e6353c0b133b7adb564a68054979 upstream.
If duration variable value is 0 at this point, it's because
chip->vendor.duration wasn't filled by tpm_get_timeouts() yet.
This patch sets then the lowest timeout just to give enough
time for tpm_get_timeouts() to further succeed.
This fix avoids long boot times in case another entity attempts
to send commands to the TPM when the TPM isn't accessible.
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit bf572541ab44240163eaa2d486b06f306a31d45a upstream.
Commit 1a855a0606 (2.6.37-rc4) fixed a problem where devices were
re-added when they shouldn't be but caused a regression in a less
common case that means sometimes devices cannot be re-added when they
should be.
In particular, when re-adding a device to an array without metadata
we should always access the device, but after the above commit we
didn't.
This patch sets the In_sync flag in that case so that the re-add
succeeds.
This patch is suitable for any -stable kernel to which 1a855a0606 was
applied.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 4e5518ca53be29c1ec3c00089c97bef36bfed515 upstream.
pcmcia_request_irq() and pcmcia_enable_device() are intended
to be called from process context (first function allocate memory
with GFP_KERNEL, second take a mutex). We can not take spin lock
and call them.
It's safe to move spin lock after pcmcia_enable_device() as we
still hold off IRQ until dev->base_addr is 0 and driver will
not proceed with interrupts when is not ready.
Patch resolves:
https://bugzilla.redhat.com/show_bug.cgi?id=643758
Reported-and-tested-by: rbugz@biobind.com
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 96a3e79edff6f41b0f115a82f1a39d66218077a7 upstream.
Added 0x0307 device id to support Motorola cables to the pl2303 usb
serial driver. This cable has a modified chip that is a pl2303, but
declares itself as 0307. Fixed by adding the right device id to the
supported devices list, assigning it the code labeled
PL2303_PRODUCT_ID_MOTOROLA.
Signed-off-by: Dario Lombardo <dario.lombardo@libero.it>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 18344a1cd5889d48dac67229fcf024ed300030d5 upstream.
I tried a magnetic stripe reader
(http://www.kimaldi.com/kimaldi_eng/productos/lectores_de_tarjetas/lectores_tarjeta_chip_y_dni/lector_hibrido_uniform_hcr_331)
and I see that it is interfaced with a PL2303. I wrote a patch to use
your driver which simply adds the product ID for the device and it
seems working fine.
From: Simone Contini <s.contini@oltrelinux.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit d0694e2aeb815042aa0f3e5036728b3db4446f1d upstream.
Unbreak Billionton CF bluetooth card. This actually fixes a regression
on zaurus.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit f8313ef1f448006207f12c107123522c8bc00f15 upstream.
i8042 controller present in Dell Vostro V13 errorneously signals spurious
timeouts.
Introduce i8042.notimeout parameter for ignoring i8042-signalled timeouts
and apply this quirk automatically for Dell Vostro V13, based on DMI match.
In addition to that, this machine also needs to be added to nomux blacklist.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Tim Gardner <tcanonical@tpi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit e3c92215198cb6aa00ad38db2780faa6b72e0a3f upstream.
gcc 4.5+ doesn't properly evaluate some inlined expressions.
A previous patch were proposed by Andrew Morton using noinline.
However, the entire inlined function is bogus, so let's just
remove it and be happy.
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 9ee91f7fb550a4c82f82d9818e42493484c754af upstream.
libsas makes use of scsi_schedule_eh() but forgets to clear the
host_eh_scheduled flag in its error handling routine. Because of this,
the error handler thread never gets to sleep; it's constantly awake and
trying to run the error routine leading to console spew and inability to
run anything else (at least on a UP system). The fix is to clear the
flag as we splice the work queue.
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit a8733c7baf457b071528e385a0b7d4aaec79287c upstream.
Our current handling of medium error assumes that data is returned up
to the bad sector. This assumption holds good for all disk devices,
all DIF arrays and most ordinary arrays. However, an LSI array engine
was recently discovered which reports a medium error without returning
any data. This means that when we report good data up to the medium
error, we've reported junk originally in the buffer as good. Worse,
if the read consists of requested data plus a readahead, and the error
occurs in readahead, we'll just strip off the readahead and report
junk up to userspace as good data with no error.
The fix for this is to have the error position computation take into
account the amount of data returned by the driver using the scsi
residual data. Unfortunately, not every driver fills in this data,
but for those who don't, it's set to zero, which means we'll think a
full set of data was transferred and the behaviour will be identical
to the prior behaviour of the code (believe the buffer up to the error
sector). All modern drivers seem to set the residual, so that should
fix up the LSI failure/corruption case.
Reported-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit d199c96d41d80a567493e12b8e96ea056a1350c1 upstream.
If anyone comes across a high-speed hub that (by mistake or by design)
claims to have no Transaction Translators, plugging a full- or
low-speed device into it will cause the USB stack to crash. This
patch (as1446) prevents the problem by ignoring such devices, since
the kernel has no way to communicate with them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Perry Neben <neben@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit c25f6b1591b158f7ae3b9132367d0fa6d632e70e upstream.
This device suffers from the off-by-one error when reporting the capacity,
so add entry with US_FL_FIX_CAPACITY.
Signed-off-by: Nick Holloway <Nick.Holloway@pyrites.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit b14de3857227cd978f515247853fd15cc2425d3e upstream.
If usb_deregister() is called after usb_serial_deregister() when
the device is plugged in, the following Oops occurs:
[ 95.337377] BUG: unable to handle kernel NULL pointer dereference at 00000010
[ 95.338236] IP: [<c0776b2d>] klist_put+0x12/0x62
[ 95.338356] *pdpt = 000000003001a001 *pde = 0000000000000000
[ 95.338356] Oops: 0000 [#1] SMP
[ 95.340499] last sysfs file: /sys/devices/pci0000:00/0000:00:1d.2/usb8/idVendor
[ 95.340499] Modules linked in: ti_usb_3410_5052(-) usbserial cpufreq_ondemand acpi_cpufreq mperf iptable_nat nf_nat iptable_mangle ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6 ip6table_filter ip6_tables ipv6 uinput arc4 ecb iwlagn iwlcore mac80211 cfg80211 microcode pcspkr acer_wmi joydev wmi sky2 [last unloaded: scsi_wait_scan]
[ 95.341908]
[ 95.341908] Pid: 1532, comm: modprobe Not tainted 2.6.37-rc7+ #6 Eiger /Aspire 5930
[ 95.341908] EIP: 0060:[<c0776b2d>] EFLAGS: 00010246 CPU: 0
[ 95.341908] EIP is at klist_put+0x12/0x62
[ 95.341908] EAX: 00000000 EBX: eedc0c84 ECX: c09c21b4 EDX: 00000001
[ 95.341908] ESI: 00000000 EDI: efaa0c1c EBP: f214fe2c ESP: f214fe1c
[ 95.341908] DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
[ 95.341908] Process modprobe (pid: 1532, ti=f214e000 task=efaaf080 task.ti=f214e000)
[ 95.341908] Stack:
[ 95.341908] f214fe24 eedc0c84 efaaf080 efaa0c1c f214fe34 c0776ba8 f214fe5c c0776c76
[ 95.341908] c09c21b4 c09c21b4 eedc0c84 efaaf080 00000000 c0634398 eafe2d1c f7b515f0
[ 95.341908] f214fe6c c0631b5c eafe2d50 eafe2d1c f214fe7c c0631ba2 eafe2d1c eafe2c00
[ 95.341908] Call Trace:
[ 95.341908] [<c0776ba8>] ? klist_del+0xd/0xf
[ 95.341908] [<c0776c76>] ? klist_remove+0x48/0x74
[ 95.341908] [<c0634398>] ? devres_release_all+0x49/0x51
[ 95.341908] [<c0631b5c>] ? __device_release_driver+0x7b/0xa4
[ 95.341908] [<c0631ba2>] ? device_release_driver+0x1d/0x28
[ 95.341908] [<c06317c4>] ? bus_remove_device+0x92/0xa1
[ 95.341908] [<c062f3d8>] ? device_del+0xf9/0x13e
[ 95.341908] [<f7b06146>] ? usb_serial_disconnect+0xd9/0x116 [usbserial]
[ 95.341908] [<c0681e3f>] ? usb_disable_interface+0x32/0x40
[ 95.341908] [<c0683972>] ? usb_unbind_interface+0x48/0xfd
[ 95.341908] [<c0631b43>] ? __device_release_driver+0x62/0xa4
[ 95.341908] [<c06320b9>] ? driver_detach+0x62/0x81
[ 95.341908] [<c0631a41>] ? bus_remove_driver+0x8f/0xae
[ 95.341908] [<c063214c>] ? driver_unregister+0x50/0x57
[ 95.341908] [<c0682f95>] ? usb_deregister+0x77/0x84
[ 95.341908] [<f7b505b6>] ? ti_exit+0x26/0x28 [ti_usb_3410_5052]
[ 95.341908] [<c046a307>] ? sys_delete_module+0x181/0x1de
[ 95.341908] [<c04e2727>] ? path_put+0x1a/0x1d
[ 95.341908] [<c047f4c5>] ? audit_syscall_entry+0x116/0x138
[ 95.341908] [<c04094df>] ? sysenter_do_call+0x12/0x28
[ 95.341908] Code: 00 83 7d f0 00 74 09 85 f6 74 05 89 f0 ff 55 f0 8b 43 04 5a 5b 5e 5f 5d c3 55 89 e5 57 56 53 89 c3 83 ec 04 8b 30 83 e6 fe 89 f0 <8b> 7e 10 88 55 f0 e8 47 26 01 00 8a 55 f0 84 d2 74 17 f6 03 01
[ 95.341908] EIP: [<c0776b2d>] klist_put+0x12/0x62 SS:ESP 0068:f214fe1c
[ 95.341908] CR2: 0000000000000010
[ 95.342357] ---[ end trace 8124d00ad871ad18 ]---
Signed-off-by: Ionut Nicu <ionut.nicu@mindbit.ro>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 271c1150b4f8e1685e5a8cbf76e329ec894481da upstream.
The major and minor number saved in the product_info structure
were copied from the address instead of the data, causing an
inconsistency in the reported versions during firmware loading:
usb 4-1: firmware: requesting edgeport/down.fw
/usr/src/linux/drivers/usb/serial/io_edgeport.c: downloading firmware version (930) 1.16.4
[..]
/usr/src/linux/drivers/usb/serial/io_edgeport.c: edge_startup - time 3 4328191260
/usr/src/linux/drivers/usb/serial/io_edgeport.c: FirmwareMajorVersion 0.0.4
This can cause some confusion whether firmware loaded successfully
or not.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit ad84e4a9efb7c8ed322bafb6ebdb9c3a49a3d3a8 upstream.
This patch (as1442) fixes a bug in g_printer: Module parameters should
not be marked "__initdata" if they are accessible in sysfs (i.e., if
the mode value in the module_param() macro is nonzero). Otherwise
attempts to access the parameters will cause addressing violations.
Character-string module parameters must not be marked "__initdata"
if the module can be unloaded, because the kernel needs to access the
parameter variable at unload time in order to free the
dynamically-allocated string.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Roland Kletzing <devzero@web.de>
CC: Craig W. Nadler <craig@nadler.us>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit f75593ceaa08e6d27aec1a5de31cded19e850dd1 upstream.
This patch (as1440) fixes a bug in ehci-hcd. ehci->periodic_size is
used to compute the size in a dma_alloc_coherent() call, but then it
gets changed later on. As a result, the corresponding call to
dma_free_coherent() passes a different size from the original
allocation. Fix the problem by adjusting ehci->periodic_size before
carrying out any of the memory allocations.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit baab93afc2844b68d57b0dcca5e1d34c5d7cf411 upstream.
AMD Hudson also needs the same ASPM quirk as SB800
Signed-off-by: Alex He <alex.he@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 12f68c480c7155a66bd2a76ab2fef28dd5f93fa2 upstream.
This patch (as1438) adds an unusual_devs entry for the MagicPixel
FW_Omega2 chip, used in the CamSport Evo camera. The firmware
incorrectly reports a vendor-specific bDeviceClass.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: <ttkspam@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit f790674d3f87df6390828ac21a7d1530f71b59c8 upstream.
Functions set_fan_min() and set_fan_div() assume that the fan_div
values have already been read from the register. The driver currently
doesn't initialize them at load time, they are only set when function
via686a_update_device() is called. This means that set_fan_min() and
set_fan_div() misbehave if, for example, "sensors -s" is called
before any monitoring application (e.g. "sensors") is has been run.
Fix the problem by always initializing the fan_div values at device
bind time.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 9c4cf6d94fb362c27a24df5223ed6e327eb7279a upstream.
This patch adds the device id for the windy31 USB device to the rt73usb
driver.
Thanks to Ralf Flaxa for reporting this and providing testing and a
sample device.
Reported-by: Ralf Flaxa <rf@suse.de>
Tested-by: Ralf Flaxa <rf@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
