| Age | Commit message (Collapse) | Author |
|---|
|
Not all graphic page remappers support physical addresses over the 4GB
mark for remapping, so while some do (the AMD64 GART always did, and I
just fixed the i965 to do so properly), we're safest off just forcing
GFP_DMA32 allocations to make sure graphics pages get allocated in the
low 32-bit address space by default.
AGP sub-drivers that really care, and can do better, could just choose
to implement their own allocator (or we could add another "64-bit safe"
default allocator for their use), but quite frankly, you're not likely
to care in practice.
So for now, this trivial change means that we won't be allocating pages
that we can't map correctly by mistake on x86-64.
[ On traditional 32-bit x86, this could never happen, because GFP_KERNEL
would never allocate any highmem memory anyway ]
Acked-by: Andi Kleen <ak@suse.de>
Acked-by: Dave Jones <davej@redhat.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Keith Packard <keithp@keithp.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
Sparse noticed a locking imbalance in tg3_open(). This patch adds an
unlock to one of the error paths, so that tg3_open() always exits
without the lock held.
Signed-off-by: Ira W. Snyder <kernel@irasnyder.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
V4L: Do not enable VIDEO_V4L2 unconditionally
The VIDEO_V4L2 config setting is enabled unconditionally, even for
configurations with no support for this subsystem whatsoever. The
following patch adds the necessary dependency.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
Having unbound PCMCIA devices: doing a 'find /sys' after a 'rmmod pcmcia'
gives an oops because the pcmcia_device is not unregisterd from the driver
core.
fixes bugzilla #7481
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Pavol Gono <Palo.Gono@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[chrisw: add subsequent mutex fix]
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
Drain the Microcode TX-status-FIFO before we enable IRQs.
This is required, because the FIFO may still have entries left
from a previous run. Those would immediately fire after enabling
IRQs and would lead to an oops in the DMA TXstatus handling code.
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
ATAPI devices transfer fixed number of bytes for CDBs (12 or 16). Some
ATAPI devices choke when shorter CDB is used and the left bytes contain
garbage. Block SG_IO cleared left bytes but SCSI SG_IO didn't. This patch
makes SCSI SG_IO clear it and simplify CDB clearing in block SG_IO.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Mathieu Fluhr <mfluhr@nero.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Douglas Gilbert <dougg@torque.net>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Cc: <stable@kernel.org>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
cciss needs to call disk_stat_add() for iostat to work.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
cpqarray needs to call disk_stat_add() for iostat to work.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
port is dereferenced even if it is NULL. Dereference it _after_ the
check if (!port)... Thanks Eric <ef87@yahoo.com> for reporting this.
This fixes
http://bugzilla.kernel.org/show_bug.cgi?id=7527
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
The PCI sysfs attributes are created after the initial PCI bus scan. With
the addition of more return value checking and assertions in the device and
sysfs layers we now can get dumps like this on sparc64:
[ 20.135032] Call Trace:
[ 20.135042] [0000000000537f88] pci_remove_bus_device+0x30/0xc0
[ 20.135076] [000000000078f890] pci_fill_in_pbm_cookies+0x98/0x440
[ 20.135109] [000000000042e828] sabre_scan_bus+0x230/0x400
[ 20.135139] [000000000078c710] pcibios_init+0x58/0xa0
[ 20.135159] [0000000000416f14] init+0x9c/0x2e0
[ 20.135190] [0000000000417a50] kernel_thread+0x38/0x60
[ 20.135211] [0000000000417170] rest_init+0x18/0x40
[ 20.135514] PCI0(PBMB): Bus running at 33MHz
It's triggering because removal of the "config" PCI sysfs file for the
device fails.
On sparc64, after probing the device, we'll delete the PCI device via
pci_remove_bus_device() if we cannot find the firmware device tree node
corresponding to it.
This is fine, but at this point the sysfs files for the PCI device won't be
setup yet.
So we should not try to do anything in pci_remove_sysfs_dev_files() if
pci_sysfs_init() has not run yet.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
The following patch resolves the divide by zero error I encountered on my
system:
http://marc.10east.com/?l=linux-fbdev-devel&m=116058257024413&w=2
I accomplished this by merging what I thought was appropriate from:
http://webcvs.freedesktop.org/xorg/driver/xf86-video-nv/src/
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
similar to the version in adbhid_input_register(): The '<>' key and the
'^°' key on a german keyboard is swapped. Provide correct keys to
userland, external USB keyboards will not work correctly when the
'badmap'/'goodmap' workarounds from xkeyboard-config are used.
It is expected that distributions drop the badmap/goodmap part from
keycodes/macintosh in the xkeyboard-config package.
This is probably 2.6.18.x material, if major distros settle on 2.6.18.
Signed-off-by: Olaf Hering <olh@suse.de>
Cc: Greg KH <greg@kroah.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
psmouse_show_int_attr() and psmouse_set_int_attr() were accessing
unsigned int fields as unsigned long, which gave garbage on x86_64.
Signed-off-by: Sergey Vlasov <vsu@altlinux.ru>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
e1000: Fix suspend/resume powerup and irq allocation
From: Auke Kok <auke-jan.h.kok@intel.com>
After 7.0.33/2.6.16, e1000 suspend/resume left the user with an enabled
device showing garbled statistics and undetermined irq allocation state,
where `ifconfig eth0 down` would display `trying to free already freed irq`.
Explicitly free and allocate irq as well as powerup the PHY during resume
fixes when needed.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
[chrisw: trivial 2.6.18 backport s/err/ret_val/]
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
use the endpoint address from the endpoint descriptor instead of the hardcoding
it to 0x81. at least some ITM based screen use a different address and don't work
without this.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Cc: Ralf Lehmann <ralf@lehmann.cc>
Cc: J.P. Delport <jpdelport@csir.co.za>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
USB: failure in usblp's error path
if urb submission fails due to a transient error here eg. ENOMEM
, the driver is dead. This fixes it.
Regards
Oliver
Signed-off-by: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
Taken from http://bugzilla.kernel.org/show_bug.cgi?id=7439
It looks like device registration in drivers/char/ipmi/ipmi_si_intf.c was
cleaned up and a small error was made when setting the class_mask. The fix
is simple as the correct mask value is defined in the code but is not used.
Acked-by: Corey Minyard <minyard@acm.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
The usbfs code doesn't provide sufficient mutual exclusion among open,
release, and remove. Release vs. remove is okay because they both
acquire the device lock, but open is not exclusive with either one. All
three routines modify the udev->filelist linked list, so they must not
run concurrently.
Apparently someone gave this a minimum amount of thought in the past by
explicitly acquiring the BKL at the start of the usbdev_open routine.
Oddly enough, there's a comment pointing out that locking is unnecessary
because chrdev_open already has acquired the BKL.
But this ignores the point that the files in /proc/bus/usb/* are not
char device files; they are regular files and so they don't get any
special locking. Furthermore it's necessary to acquire the same lock in
the release and remove routines, which the code does not do.
Yet another problem arises because the same file_operations structure is
accessible through both the /proc/bus/usb/* and /dev/usb/usbdev* file
nodes. Even when one of them has been removed, it's still possible for
userspace to open the other. So simple locking around the individual
remove routines is insufficient; we need to lock the entire
usb_notify_remove_device notifier chain.
Rather than rely on the BKL, this patch (as723) introduces a new private
mutex for the purpose. Holding the BKL while invoking a notifier chain
doesn't seem like a good idea.
Cc: Dave Jones <davej@redhat.com>
[https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=212952]
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
The Jmicron JMB368 is PATA only so has the PATA on function zero. Don't
therefore skip function zero on this device when probing
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
My K8T800 mobo resumes fine from suspend to ram with and without patch
applied against 2.6.18.
quirk_via_abnormal_poweroff makes some boards not boot 2.6.18, so IMO patch
should go to head, 2.6.18.2 and everywhere "ACPI: ACPICA 20060623" has been
applied.
Remove quirk_via_abnormal_poweroff
Obsoleted by "ACPI: ACPICA 20060623":
<snip>
Implemented support for "ignored" bits in the ACPI
registers. According to the ACPI specification, these
bits should be preserved when writing the registers via
a read/modify/write cycle. There are 3 bits preserved
in this manner: PM1_CONTROL[0] (SCI_EN), PM1_CONTROL[9],
and PM1_STATUS[11].
http://bugzilla.kernel.org/show_bug.cgi?id=3691
</snip>
Signed-off-by: Karsten Wiese <fzu@wemgehoertderstaat.de>
Cc: Bob Moore <robert.moore@intel.com>
Acked-by: Len Brown <len.brown@intel.com>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
This is a particularly ugly on-failure bug, possibly security, since the
lack of error handling here is covering up another class of bug: failure to
handle copy_to_user() return values.
The I4L API function ->readstat() returns an integer, and by looking at
several existing driver implementations, it is clear that a negative return
value was meant to indicate an error.
Given that several drivers already return a negative value indicating an
errno-style error, the current code would blindly accept that [negative]
value as a valid amount of bytes read. Obvious damage ensues.
Correcting ->readstat() handling to properly notice errors fixes the
existing code to work correctly on error, and enables future patches to
more easily indicate errors during operation.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Cc: Karsten Keil <kkeil@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
Most of the ISDN ->readstat() implementations needed to check
copy_to_user() and put_user() return values.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
Fix October-only BCD-to-binary conversion bug:
0x08 -> 7
0x09 -> 8
0x10 -> 15 (!)
0x11 -> 19
Fixes http://bugzilla.kernel.org/show_bug.cgi?id=7361
Cc: Raphael Assenat <raph@raphnet.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
Previously, since determination whether there was an Intel random number
generator was based on a single bit, on systems with a matching bridge
device but without a firmware hub, there was a 50% chance that the code
would incorrectly decide that the system had an RNG. This patch adds
detection of the firmware hub to better qualify the existence of an RNG.
There is one issue with the patch: I was unable to determine the LPC
equivalent for the PCI bridge 8086:2430 (since the old code didn't care
about which of the many devices provided by the ICH/ESB it was chose to use
the PCI bridge device, but the FWH settings live in the LPC device, so the
device list needed to be changed).
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
[WATCHDOG] sc1200wdt.c pnp unregister fix.
If no devices found or invalid parameter is specified,
scl200wdt_pnp_driver is left unregistered.
It breaks global list of pnp drivers.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
[SCSI] aic7xxx: pause sequencer before touching SBLKCTL
Some cards need to pause the sequencer before the SBLKCTL register is
touched. This fixes a PCI related oops seen on powerpc macs with this
card caused by trying to ascertain the bus signalling before beginning
domain validation.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
The reason sky2 driver was locking up on transmit on the Yukon-FE chipset
is that it was misconfiguring the internal RAM buffer so the transmitter
and receiver were sharing the same space. It is a wonder it worked at all!
This patch addresses this, and fixes an easily reproducible hang on Transmit.
Only the Yukon-FE chip is Marvell 88E803X (10/100 only) are affected.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
We discovered a problem when running IPoIB applications on multiple
CPUs on an Altix system. Many messages such as:
ib_mthca 0002:01:00.0: SQ 000014 full (19941644 head, 19941707 tail, 64 max, 0 nreq)
appear in syslog, and the driver wedges up.
Apparently this is because writes to the doorbells from different CPUs
reach the device out of order. The following patch adds mmiowb() calls
after doorbell rings to ensure the doorbell writes are ordered.
Signed-off-by: Arthur Kepner <akepner@sgi.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
When ipoib_ib_dev_flush() is called because of a port event, the
driver needs to rejoin all multicast groups, since the flush will call
ipoib_mcast_dev_flush() (via ipoib_ib_dev_down()). Otherwise no
(non-broadcast) multicast groups will be rejoined until the networking
core calls ->set_multicast_list again, and so multicast reception will
be broken for potentially a long time.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
[SCSI] aic7xxx: avoid checking SBLKCTL register for certain cards
For cards that don't support LVD, checking the SBLKCTL register to
determine the bus singalling doesn't work. So, check that the card
supports LVD first (AHC_ULTRA2) before checking the register.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
Two less-used md personalities have bugs in the calculation of
->degraded (the extent to which the array is degraded).
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
become live.
If save_raid_disk is >= 0, then the device could be a device that is
already in sync that is being re-added. So we need to default this
value to -1.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
DVB: fix dvb_pll_attach for mt352/zl10353 in cx88-dvb, and nxt200x
Typical wiring of MT352, ZL10353, NXT2002 and NXT2004 based tuners
differ from dvb-pll's expectation that the PLL is directly accessible.
On these boards, the PLL is actually hidden behind the demodulator, and
as such can only be accessed via the demodulator's interface. It was
failing to communicate with the PLL during an attach test and
subsequently not connecting the tuner ops.
By passing a NULL I2C bus handle to dvb_pll_attach, this accessibility
check can be bypassed. Do this for the affected boards. Also fix a
possible NULL dereference at sleep time, which would otherwise be
exposed by this change.
This patch has been backported to the 2.6.18.y stable kernel series
from the original changesets from Chris Pascoe and Michael Krufky,
already present in the upstream 2.6.19 kernel tree.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
This fixes a netdev watchdog timeout problem.
The problem is caused by a needed netif_tx_disable
in the hardware calibration code and can be shown by the
following timegraph.
|---5secs - ~10 jiffies time---|---|OOPS
^ ^
last real TX periodic work stops netif
At OOPS, the following happens:
The watchdog timer triggers, because the timeout of 5secs
is over. The watchdog first checks for stopped TX.
_Usually_ TX is only stopped from the TX handler to indicate
a full TX queue. But this is different. We need to stop TX here,
regardless of the TX queue state. So the watchdog recognizes
the stopped device and assumes it is stopped due to full
TX queues (Which is a _wrong_ assumption in this case). It then
tests how far the last TX has been in the past. If it's more than
5secs (which is the case for low or no traffic), it will fire
a TX timeout.
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
[SERIAL] Fix oops when removing suspended serial port
A serial card might have been removed when the system is resumed.
This results in a suspended port being shut down, which results in
the ports shutdown method being called twice in a row. This causes
BUGs. Avoid this by tracking the suspended state separately from
the initialised state.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: maximilian attems <maks@sternwelten.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
Unfortunately, pcmcia_dev_present() returns false when a device is
suspended, so checking this on resume does not work too well. Omit
this test.
the backported patch below is already in fedora tree. -maks
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: maximilian attems <maks@sternwelten.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
The uninitialised pmu_backlight_lock causes the current Fedora test kernel
(which has spinlock debugging enabled) to panic on suspend.
This is suboptimal, so I fixed it.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Michael Hanselmann <linux-kernel@hansmi.ch>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
[SCSI] DAC960: PCI id table fixup
The PCI ID table in the DAC960 driver conflicts with some devices
that use the ipr driver. All ipr adapters that use this chip
have an IBM subvendor ID and all DAC960 adapters that use this
chip have a Mylex subvendor id.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
This reverts earlier change that attempted to fix flow control.
Device needs to discard pause frames, otherwise it passes pause frames up
the stack.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
When using flow control, the PHY needs to accept multicast pause frames.
Without this fix, these frames were getting discarded by the PHY before
doing any flow control.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
When PHY is turned off on shutdown, it can causes the IRQ to get stuck on.
Make sure and disable the IRQ first, and if IRQ occurs when device
is not running, don't access PHY because that can hang.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
The lower pause threshold set by the driver is too large and causes FIFO overruns.
Especially on laptops running at slower clock rates.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
Make sure and do PCI reads after writes in the MSI test setup code.
Some motherboards don't implement MSI correctly. The driver handles this
but the warning is too verbose and overly cautious.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
|
|
This patch fixes a copy-paste bug in videodev.c where the vidioc_qbuf()
function gets called for the dqbuf ioctl.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The bcm43xx code in 2.6.18 has a serious problems not found in 2.6.17, due to
a change in the locking mechanism introduced to reduce latency. The following patch
fixes the problems in locking, reduces the latency associated with the periodic
work tasklet, and contains code needed for those cards that use 64-bit DMA.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Some people find their Jmicron pata port reports its disabled even
though it has devices on it and was boot probed. Fix this
(Candidate for 2.6.18.*, less so for 2.6.19 as we've got a proper
jmicron driver on the merge for that to replace ide-generic support)
From: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Fix paren-placement / precedence bug breaking initialization for 1 MHz
clock mode.
Also fix comment spelling error, and fence-post (off-by-one) error on
symbol used in request_region.
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=7242
Thanks alexander.krause@erazor-zone.de, dzpost@dedekind.net, for the
reports and patch test, and phelps@mantara.com for the independent patch
and verification.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Cc: <alexander.krause@erazor-zone.de>
Cc: <dzpost@dedekind.net>
Cc: <phelps@mantara.com>
Acked-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The century bit PCF8563_MO_C in the month register is misinterpreted. It
is set to 1 for the 20th century and 0 for 21th, and the driver is
expecting the opposite behavior.
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Address http://bugzilla.kernel.org/show_bug.cgi?id=7189
It should check `clen', not `len'.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: <jurij@wooyd.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Willy Tarreau <w@1wt.eu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
If a drive is added with HOT_ADD_DISK rather than ADD_NEW_DISK,
saved_raid_disk isn't initialised properly, and the drive can be
included in the array without a resync.
From: Neil Brown <neilb@suse.de>
Cc: <syrius.ml@no-log.org>
Cc: Richard Bollinger <rabollinger@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
