| Age | Commit message (Collapse) | Author |
|---|
|
PPPoE must advertise the underlying device's MTU via the ppp channel
descriptor structure, as multilink functionality depends on it.
Signed-off-by: Michal Ostrowski <mostrows@earthlink.net>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
Add a modeline for the Philips 200W display. aty128fb does not do DDC, it
picks 1920x1440 or similar. It works ok with nvidiafb because it can ask
for DDC data.
mode "1680x1050-60"
# D: 146.028 MHz, H: 65.191 kHz, V: 59.863 Hz
geometry 1680 1050 1680 1050 16
timings 6848 280 104 30 3 176 6
hsync high
vsync high
rgba 5/11,6/5,5/0,0/0
endmode
hwinfo --monitor
20: None 00.0: 10000 Monitor
[Created at monitor.206]
Unique ID: rdCR.pzUFTofo1S4
Parent ID: 002j.bJRsY88eNSC
Hardware Class: monitor
Model: "PHILIPS Philips 200W"
Vendor: PHL "PHILIPS"
Device: eisa 0x0832 "Philips 200W"
Serial ID: "VN 016596"
Resolution: 720x400@70Hz
Resolution: 640x480@60Hz
Resolution: 640x480@67Hz
Resolution: 640x480@72Hz
Resolution: 640x480@75Hz
Resolution: 800x600@56Hz
Resolution: 800x600@60Hz
Resolution: 800x600@72Hz
Resolution: 800x600@75Hz
Resolution: 832x624@75Hz
Resolution: 1024x768@60Hz
Resolution: 1024x768@70Hz
Resolution: 1024x768@75Hz
Resolution: 1280x1024@75Hz
Resolution: 1152x864@70Hz
Resolution: 1152x864@75Hz
Resolution: 1280x960@60Hz
Resolution: 1280x1024@60Hz
Resolution: 1680x1050@60Hz
Size: 433x271 mm
Driver Info #0:
Max. Resolution: 1680x1050
Vert. Sync Range: 56-85 Hz
Hor. Sync Range: 30-93 kHz
Config Status: cfg=new, avail=yes, need=no, active=unknown
Attached to: #5 (VGA compatible controller)
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
Don't program the GMAC to reject flow control packets.
This maybe the cause of some of the transmit hangs.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
Fix support for fiber based devices. Needed to keep track of PMD type to
add workaround in setup. Add support for gigabit half duplex fiber.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
Several code paths assume an additional 16 bytes of header padding
on the receive path. Use dev_alloc_skb to get that padding.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
Backport the budget driver DISEQC instability fix.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
|
|
Backport fix to artec USB DVB devices
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
The budget-av needs this GPIO set low for most cards to work.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
ULE (Unidirectional Lightweight Encapsulation RFC 4326) decapsulation
code has a bug that allows an attacker to send a malformed ULE packet
with SNDU length of 0 and bring down the receiving machine. This patch
fix the bug and has been tested on version 2.6.17.11. This bug is 100%
reproducible and the modified source code (GPL) used to produce this bug
will be posted on http://nrg.cs.usm.my/downloads.htm shortly. The
kernel will produce a dump during CRC32 checking on faulty ULE packet.
Signed-off-by: Ang Way Chuang <wcang@nrg.cs.usm.my>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
Keys on Yealink based phones will not function properly when using the
generic HID driver. This patch prevents the generic HID code from
grabbing the device before the regular yealink driver can get a grip on
it.
Signed-off-by: Henk Vergonet <Henk.Vergonet@gmail.com>
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
This patch fixes a memory leak and a kernel oops when trying to unload
the driver, due to an unbalanced cleanup.
Thanks Ivar Jensen for spotting my mistake.
Signed-off-by: Henk Vergonet <henk.vergonet@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
This patch fixes a bug in the handling of 'ignore' module parameters of I2C
client drivers.
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
This patch
- works around a bug in the I2C bridge that makes the initialization
of the TDA10046 fail on recent LifeView cards
- puts the AGC output to tristate in sleep mode. This is necessary for
recent hybrid cards that switch the AGC via tristateing.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
The via-velocity driver reports incorrect speed and link detected status
as viewed by ethtool (and probably other tools). This patch fixes those
incorrect reports and prettifies a long line.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
The patch fixes http://bugzilla.kernel.org/show_bug.cgi?id=6711
Signed-off-by: Roy Marples <uberlord@gentoo.org>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
This patch enables agpgart on a Via "PT880 Ultra" based motherboard
(Asus P4V800D-X). The PCI ID of the PT880 Ultra is 0x0308 instead of
0x0258 of the PT880.
The patched via-agp passes testgart.
Signed-off-by: Magnus Kessler <Magnus.Kessler@gmx.net>
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
From: Julien Tous <julien.tous@gmail.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
- Set outputs to tristate in sleep mode
- Reduce dangerously high firmware download speed with 16MHz xtal
- added tda827x configuration with GPIOs low
- added comments to stupid looking IIC reads that work around bugs in
the tda10046.
- some minor updates
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
based on drivers/media/common/ir-keymaps.c:ir_codes_flydvb
in Linus' tree.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
There seem to be many variants of this cards with different
feature sets. This entry supports
analog TV, CVBS and s-video input, FM radio and DVB-T
if they are supported by the hardware.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
The .vmux entry needs to be 1 instead of 0
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
Added ID entries for the Genius VideoWonder DVB-T
and the LifeView FlyTV Platinum Gold
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
The saa7134 drivers uses request_firmware()
and thus needs to select FW_LOADER.
Signed-off-by: maximilian attems <maks@sternwelten.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
The device, Medion 7134, has two saa7134 chips on it, but only one of them
is functional in the current saa7134 driver.
This patch adds autodetection for the second, unsupported saa7134 chip,
as SAA7134_BOARD_MD7134_BRIDGE_2, and displays a message to the user
(in dmesg) indicating that the second chip isn't yet functional.
This is useful for users, since two instances of the saa7134 driver
will spawn. This patch will prevent confusion by warning the user that
only one of the chips on the board are functional.
There are other versions of the SAA7134_BOARD_MD7134 with only a single
saa7134 bridge/decoder -- those devices will not be affected by this patch.
Only devices containing the second chip will display the warning.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
There are already some supported devices that contain two
saa713x chips on-board, where only one of these chips is
currently functional in the driver.
We are already printing a warning message for the second
saa7134 decoder in SAA7134_BOARD_AVERMEDIA_A169_B. This
patch alters that case to make it generic, so that other
cards in the same situation can use it.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
- Added support for AVerMedia A169 Dual Analog tuner card
(dual saa7134 decoders - only 1 working right now)
- Added autodetection for both parts of the card.
It shows up like 2 cards, B1 and B
- Enabled tuner B1, SVIDEO on B1 and composite1 through SVIDEO,
FIXME: B is more or less dead at this point and I suspect the
FM-radio is on the B part of the board
Adrian Bunk:
slightly adapted to 2.6.16
Signed-off-by: Rickard Osser <ricky@osser.se>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
I have the same card with the same PCI id, but from KWorld.
The patch documents that this is the same card.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
- Corrected autodetection for saa7130 card:
subsystem: 1048:226c, board: ELSA EX-VISION 700TV
Signed-off-by: TAMUKI Shoichi <tamuki@linet.gr.jp>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
- Enable the tuv1236 tuner on the Kworld-ATSC110 card so that the
tuner can be identified when tuners.ko loads.
- With this change it is no longer necessary to remove and reload
the tuner module in order to get the tuv1236 identified.
- This code was copied from the ATI HDTV Wonder init routine (in cx88-cards.c)
which also uses the TUV1236D.
Signed-off-by: Curt Meyers <cmeyers@boilerbots.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
- There is no radio with this tuner card...
Thanks-to: Dwaine Garden <DwaineGarden@rogers.com>
- fixed capitalization in card name.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
- corrected composite input.
- verified s-video input.
Signed-off-by: Curt Meyers <cmeyers@boilerbots.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
- When tuning VSB, use ANT input
- When tuning QAM, use CABLE input
Signed-off-by: Curt Meyers <cmeyers@boilerbots.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
Signed-off-by: Andrew Burri <andrew.burri@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
Add support for ELSA EX-VISION 700TV, which is the ELSA Japan's
flagship model of the software encoding TV capture card.
All inputs (Television, Composite1 and S-Video) have been tested.
Signed-off-by: Tamuki Shoichi <tamuki@linet.gr.jp>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
This is an analog / digital hybrid card.
Signed-off-by: Peter Hartshorn <p3r@users.sourceforge.net>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
Analog and DVB-T are working, Remote not yet.
This card is based on the new LifeView design, there should be many variants.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
Additionally to the card support, this changeset adds the option
tda10046lifeview to get_dvb_firmware to download tda10046 firmware
from LifeView's site.
Signed-off-by: Giampiero Giancipoli <gianci@libero.it>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
Signed-off-by: Jose Alberto Reguero <jareguero@telefonica.net>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
The icom driver uses request_firmware()
and thus needs to select FW_LOADER.
Signed-off-by: maximilian attems <maks@sternwelten.at>
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
* MODE_MASK is unused in eicon driver.
* Conflicts with a ptrace stuff on arm.
drivers/isdn/hardware/eicon/divasync.h:259:1: warning: "MODE_MASK" redefined
include2/asm/ptrace.h:48:1: warning: this is the location of the previous definition
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Karsten Keil <kkeil@suse.de>
Acked-by: Armin Schindler <armin@melware.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
This patch fixes the aic79xx driver to properly respond to BIOS
settings.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
Serialize processing of tty buffers in flush_to_ldisc
to fix (very rare) corruption of tty buffer free list
on SMP systems.
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
At the point where this 'atomic_add' is, rdev could be NULL,
as seen by the fact that we test for this in the very next
statement.
Further is it is really the wrong place of the add.
We could add to the count of corrected errors
once the are sure it was corrected, not before
trying to correct it.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
Recently a patch was added for preliminary suspend/resume handling on
!PPC_PMAC. However, this broke both suspend and firewire on powerpc
because it saves the pci state after the device has already been disabled.
This moves the save state to before the pmac specific code.
Signed-off-by: Danny Tholen <obiwan@mailmij.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
The code really means to mask off the high bits, not assign 0xff.
Reported by Marcus Meissner <meissner@suse.de>.
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
During an STR resume cycle, the ide master disk times-out when there is
also a slave present (especially CD). Increasing the timeout in ide-io
from 10,000 to 100,000 fixes this problem.
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
At least Maxtor OneTouch III require a "start stop unit" command after
auto spin-down before the next access can proceed. This patch activates
the responsible code in scsi_mod for all Maxtor SBP-2 disks.
https://bugzilla.novell.com/show_bug.cgi?id=183011
Maybe that should be done for all SBP-2 disks, but better be cautious.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
I've been experimenting to track down the cause of suspend/resume problems
on my Compaq Presario X1050 laptop:
http://bugzilla.kernel.org/show_bug.cgi?id=6075
Essentially the ACPI Embedded Controller and keyboard controller would
get into a bizarre, confused state after resume.
I found that unloading the ohci1394 module before suspend and reloading it
after resume made the problem go away. Diffing the dmesg output from
resume, with and without the module loaded, I found that with the module
loaded I was missing these:
PM: Writing back config space on device 0000:02:00.0 at offset 1. (Was 2100080, writing 2100007)
PM: Writing back config space on device 0000:02:00.0 at offset 3. (Was 0, writing 8008)
PM: Writing back config space on device 0000:02:00.0 at offset 4. (Was 0, writing 90200000)
PM: Writing back config space on device 0000:02:00.0 at offset 5. (Was 1, writing 2401)
PM: Writing back config space on device 0000:02:00.0 at offset f. (Was 20000100, writing 2000010a)
The default PCI driver performs the pci_restore_state when no driver is
loaded for the device. When the ohci1394 driver is loaded, it is supposed
to do this, however it appears not to do so.
I created the patch below and tested it, and it appears to resolve the
suspend problems I was having with the module loaded. I only added in the
pci_save_state and pci_restore_state - however, though I know little of
this hardware, surely the driver should really be doing more than this when
suspending and resuming? Currently it does almost nothing, what if there
are commands in progress, etc?
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
kernel.org bugzilla #6206
Based on patch from Serge Belyshev <belyshev@depni.sinp.msu.ru>
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
