| Age | Commit message (Collapse) | Author |
|---|
|
commit b0a50e92bda3c4aeb8017d4e6c6e92146ebd5c9b upstream.
Leandro Liptak reports that his HASEE E200 computer hangs when we ask
the BIOS to hand over control of the EHCI host controller. This
definitely sounds like a bug in the BIOS, but at the moment there is
no way to fix it.
This patch works around the problem by avoiding the handoff whenever
the motherboard and BIOS version match those of Leandro's computer.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Leandro Liptak <leandroliptak@gmail.com>
Tested-by: Leandro Liptak <leandroliptak@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 5dc2808c4729bf080487e61b80ee04e0fdb12a37 upstream.
Lists of endpoints are stored for bandwidth calculation for roothub ports.
Make sure we remove all endpoints from the list before the whole device,
containing its endpoints list_head stuctures, is freed.
This used to be done in the wrong order in xhci_mem_cleanup(),
and triggered an oops in resume from S4 (hibernate).
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit e4d58f5dcb7d7be45df8def31881ebfae99c75da upstream.
TEST 12 and TEST 24 unlinks the URB write request for N times. When
host and gadget both initialize pattern 1 (mod 63) data series to
transfer, the gadget side will complain the wrong data which is not
expected. Because in host side, usbtest doesn't fill the data buffer
as mod 63 and this patch fixed it.
[20285.488974] dwc3 dwc3.0.auto: ep1out-bulk: Transfer Not Ready
[20285.489181] dwc3 dwc3.0.auto: ep1out-bulk: reason Transfer Not Active
[20285.489423] dwc3 dwc3.0.auto: ep1out-bulk: req ffff8800aa6cb480 dma aeb50800 length 512 last
[20285.489727] dwc3 dwc3.0.auto: ep1out-bulk: cmd 'Start Transfer' params 00000000 a9eaf000 00000000
[20285.490055] dwc3 dwc3.0.auto: Command Complete --> 0
[20285.490281] dwc3 dwc3.0.auto: ep1out-bulk: Transfer Not Ready
[20285.490492] dwc3 dwc3.0.auto: ep1out-bulk: reason Transfer Active
[20285.490713] dwc3 dwc3.0.auto: ep1out-bulk: endpoint busy
[20285.490909] dwc3 dwc3.0.auto: ep1out-bulk: Transfer Complete
[20285.491117] dwc3 dwc3.0.auto: request ffff8800aa6cb480 from ep1out-bulk completed 512/512 ===> 0
[20285.491431] zero gadget: bad OUT byte, buf[1] = 0
[20285.491605] dwc3 dwc3.0.auto: ep1out-bulk: cmd 'Set Stall' params 00000000 00000000 00000000
[20285.491915] dwc3 dwc3.0.auto: Command Complete --> 0
[20285.492099] dwc3 dwc3.0.auto: queing request ffff8800aa6cb480 to ep1out-bulk length 512
[20285.492387] dwc3 dwc3.0.auto: ep1out-bulk: Transfer Not Ready
[20285.492595] dwc3 dwc3.0.auto: ep1out-bulk: reason Transfer Not Active
[20285.492830] dwc3 dwc3.0.auto: ep1out-bulk: req ffff8800aa6cb480 dma aeb51000 length 512 last
[20285.493135] dwc3 dwc3.0.auto: ep1out-bulk: cmd 'Start Transfer' params 00000000 a9eaf000 00000000
[20285.493465] dwc3 dwc3.0.auto: Command Complete --> 0
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 8a61ba3a47ac39f660702aa66a172185dd605a86 upstream.
Adds product ID for the Novatel E371 PCI Express Mini Card.
$ lsusb
Bus 001 Device 024: ID 1410:9011 Novatel Wireless
$ usb-devices
T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#= 24 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1410 ProdID=9011 Rev=00.03
S: Manufacturer=Novatel Wireless, Inc.
S: Product=Novatel Wireless HSPA
S: SerialNumber=012773002115811
C: #Ifs= 6 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 6 Alt= 0 #EPs= 1 Cls=02(commc) Sub=06 Prot=00 Driver=cdc_ether
I: If#= 7 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
Tested with kernel 3.2.0.
Signed-off-by: Alexej Starschenko <starschenko@gmail.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit d0839d757e6294921c31b1c4ca4f1dcc5df63bcd upstream.
The NovaTech OrionLXm uses an onboard FTDI serial converter for JTAG and
console access.
Here is the lsusb output:
Bus 004 Device 123: ID 0403:7c90 Future Technology Devices
International, Ltd
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit c03890ff5e24a4bf59059f2d179f427559b7330a upstream.
A recent patch that purported to fix firmware download on big-endian
machines failed to add the corresponding sparse annotation to the
i2c-header. This was reported by the kbuild test robot.
Adding the appropriate annotation revealed another endianess bug related
to the i2c-header Size-field in a code path that is exercised when the
firmware is actually being downloaded (and not just verified and left
untouched unless older than the firmware at hand).
This patch adds the required sparse annotation to the i2c-header and
makes sure that the Size-field is sent in little-endian byte order
during firmware download also on big-endian machines.
Note that this patch is only compile-tested, but that there is no
functional change for little-endian systems.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Ludovic Drolez <ldrolez@debian.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 183a45087d126d126e8dd1d9b2602fc129dff9ad upstream.
Make sure to check return value of autopm get in write() in order to
avoid urb leak and PM counter imbalance on errors.
Fixes: 11ea859d64b6 ("USB: additional power savings for cdc-acm devices
that support remote wakeup")
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2:
- Adjust context
- Error/status variable is called rc, not stat]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit bae3f4c53585e9a170da9436e0f06919874bda9a upstream.
Fix runtime PM handling of control messages by adding the required PM
counter operations.
Fixes: 11ea859d64b6 ("USB: additional power savings for cdc-acm devices
that support remote wakeup")
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 140cb81ac8c625942a1d695875932c615767a526 upstream.
The current ACM runtime-suspend implementation is broken in several
ways:
Firstly, it buffers only the first write request being made while
suspended -- any further writes are silently dropped.
Secondly, writes being dropped also leak write urbs, which are never
reclaimed (until the device is unbound).
Thirdly, even the single buffered write is not cleared at shutdown
(which may happen before the device is resumed), something which can
lead to another urb leak as well as a PM usage-counter leak.
Fix this by implementing a delayed-write queue using urb anchors and
making sure to discard the queue properly at shutdown.
Fixes: 11ea859d64b6 ("USB: additional power savings for cdc-acm devices
that support remote wakeup")
Reported-by: Xiao Jin <jin.xiao@intel.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit e144ed28bed10684f9aaec6325ed974d53f76110 upstream.
Fix race between write() and resume() due to improper locking that could
lead to writes being reordered.
Resume must be done atomically and susp_count be protected by the
write_lock in order to prevent racing with write(). This could otherwise
lead to writes being reordered if write() grabs the write_lock after
susp_count is decremented, but before the delayed urb is submitted.
Fixes: 11ea859d64b6 ("USB: additional power savings for cdc-acm devices
that support remote wakeup")
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2:
- Adjust context
- Move mutex_lock(acm->mutex) above acquisition of spinlocks]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 5a345c20c17d87099224a4be12e69e5bd7023dca upstream.
Fix race between write() and suspend() which could lead to writes being
dropped (or I/O while suspended) if the device is runtime suspended
while a write request is being processed.
Specifically, suspend() releases the write_lock after determining the
device is idle but before incrementing the susp_count, thus leaving a
window where a concurrent write() can submit an urb.
Fixes: 11ea859d64b6 ("USB: additional power savings for cdc-acm devices
that support remote wakeup")
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit fb7ad4f93d9f0f7d49beda32f5e7becb94b29a4d upstream.
Keep trying to submit urbs rather than bail out on first read-urb
submission error, which would also prevent I/O for any further ports
from being resumed.
Instead keep an error count, for all types of failed submissions, and
let USB core know that something went wrong.
Also make sure to always clear the suspended flag. Currently a failed
read-urb submission would prevent cached writes as well as any
subsequent writes from being submitted until next suspend-resume cycle,
something which may not even necessarily happen.
Note that USB core currently only logs an error if an interface resume
failed.
Fixes: 383cedc3bb43 ("USB: serial: full autosuspend support for the
option driver")
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 79eed03e77d481b55d85d1cfe5a1636a0d3897fd upstream.
The delayed-write queue was never emptied at shutdown (close), something
which could lead to leaked urbs if the port is closed before being
runtime resumed due to a write.
When this happens the output buffer would not drain on close
(closing_wait timeout), and after consecutive opens, writes could be
corrupted with previously buffered data, transfered with reduced
throughput or completely blocked.
Note that unbusy_queued_urb() was simply moved out of CONFIG_PM.
Fixes: 383cedc3bb43 ("USB: serial: full autosuspend support for the
option driver")
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2: adjust indentation]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 170fad9e22df0063eba0701adb966786d7a4ec5a upstream.
Fix race between write() and suspend() which could lead to writes being
dropped (or I/O while suspended) if the device is runtime suspended
while a write request is being processed.
Specifically, suspend() releases the susp_lock after determining the
device is idle but before setting the suspended flag, thus leaving a
window where a concurrent write() can submit an urb.
Fixes: 383cedc3bb43 ("USB: serial: full autosuspend support for the
option driver")
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit d9e93c08d8d985e5ef89436ebc9f4aad7e31559f upstream.
We find a race between write and resume. usb_wwan_resume run play_delayed()
and spin_unlock, but intfdata->suspended still is not set to zero.
At this time usb_wwan_write is called and anchor the urb to delay
list. Then resume keep running but the delayed urb have no chance
to be commit until next resume. If the time of next resume is far
away, tty will be blocked in tty_wait_until_sent during time. The
race also can lead to writes being reordered.
This patch put play_Delayed and intfdata->suspended together in the
spinlock, it's to avoid the write race during resume.
Fixes: 383cedc3bb43 ("USB: serial: full autosuspend support for the
option driver")
Signed-off-by: xiao jin <jin.xiao@intel.com>
Signed-off-by: Zhang, Qi1 <qi1.zhang@intel.com>
Reviewed-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2: there's no need to check for portdata == NULL]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit db0904737947d509844e171c9863ecc5b4534005 upstream.
When enable usb serial for modem data, sometimes the tty is blocked
in tty_wait_until_sent because portdata->out_busy always is set and
have no chance to be cleared.
We find a bug in write error path. usb_wwan_write set portdata->out_busy
firstly, then try autopm async with error. No out urb submit and no
usb_wwan_outdat_callback to this write, portdata->out_busy can't be
cleared.
This patch clear portdata->out_busy if usb_wwan_write try autopm async
with error.
Fixes: 383cedc3bb43 ("USB: serial: full autosuspend support for the
option driver")
Signed-off-by: xiao jin <jin.xiao@intel.com>
Signed-off-by: Zhang, Qi1 <qi1.zhang@intel.com>
Reviewed-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit acf47d4f9c39b1cba467aa9442fc2efe0b1da741 upstream.
Fix potential I/O while runtime suspended due to missing PM operations
in send_setup.
Fixes: 383cedc3bb43 ("USB: serial: full autosuspend support for the
option driver")
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 80cc0fcbdaeaf10d04ba27779a2d7ceb73d2717a upstream.
Make sure that needs_remote_wake up is always set when there are open
ports.
Currently close() would unconditionally set needs_remote_wakeup to 0
even though there might still be open ports. This could lead to blocked
input and possibly dropped data on devices that do not support remote
wakeup (and which must therefore not be runtime suspended while open).
Add an open_ports counter (protected by the susp_lock) and only clear
needs_remote_wakeup when the last port is closed.
Fixes: e6929a9020ac ("USB: support for autosuspend in sierra while
online")
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2: adjust indentation]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 014333f77c0b71123d6ef7d31a9724e0699c9548 upstream.
The delayed-write queue was never emptied on disconnect, something which
would lead to leaked urbs and transfer buffers if the device is
disconnected before being runtime resumed due to a write.
Fixes: e6929a9020ac ("USB: support for autosuspend in sierra while
online")
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2: adjust context, indentation]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 7fdd26a01eb7b6cb6855ff8f69ef4a720720dfcb upstream.
Neither the transfer buffer or the urb itself were released in the
resume error path for delayed writes. Also on errors, the remainder of
the queue was not even processed, which leads to further urb and buffer
leaks.
The same error path also failed to balance the outstanding-urb counter,
something which results in degraded throughput or completely blocked
writes.
Fix this by releasing urb and buffer and balancing counters on errors,
and by always processing the whole queue even when submission of one urb
fails.
Fixes: e6929a9020ac ("USB: support for autosuspend in sierra while
online")
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 353fe198602e8b4d1c7bdcceb8e60955087201b1 upstream.
Fix AA deadlock in open error path that would call close() and try to
grab the already held disc_mutex.
Fixes: b9a44bc19f48 ("sierra: driver urb handling improvements")
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 8ef42ddd9a53b73e6fc3934278710c27f80f324f upstream.
Not all host controller drivers have bus-suspend and bus-resume
methods. When one doesn't, it will cause problems if runtime PM is
enabled in the kernel. The PM core will attempt to suspend the
controller's root hub, the suspend will fail because there is no
bus-suspend routine, and a -EBUSY error code will be returned to the
PM core. This will cause the suspend attempt to be repeated shortly
thereafter, in a never-ending loop.
Part of the problem is that the original error code -ENOENT gets
changed to -EBUSY in usb_runtime_suspend(), on the grounds that the PM
core will interpret -ENOENT as meaning that the root hub has gotten
into a runtime-PM error state. While this change is appropriate for
real USB devices, it's not such a good idea for a root hub. In fact,
considering the root hub to be in a runtime-PM error state would not
be far from the truth. Therefore this patch updates
usb_runtime_suspend() so that it adjusts error codes only for
non-root-hub devices.
Furthermore, the patch attempts to prevent the problem from occurring
in the first place by not enabling runtime PM by default for root hubs
whose host controller driver doesn't have bus_suspend and bus_resume
methods.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Will Deacon <will.deacon@arm.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2: runtime PM is also not supported for USB 3.0
non-root hubs]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 6ed07d45d09bc2aa60e27b845543db9972e22a38 upstream.
Signed-off-by: Daniele Forsi <dforsi@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit f0ef5d41792a46a1085dead9dfb0bdb2c574638e upstream.
Signed-off-by: Victor A. Santos <victoraur.santos@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit df602c2d2358f02c6e49cffc5b49b9daa16db033 upstream.
Even if the USB-to-ATAPI converter supported multiple LUNs, this
driver would always detect the same physical device or media because
it doesn't use srb->device->lun in any way.
Tested with an Hewlett-Packard CD-Writer Plus 8200e.
Signed-off-by: Daniele Forsi <dforsi@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 34f972d6156fe9eea2ab7bb418c71f9d1d5c8e7b upstream.
A number of older CMOTech modems are based on Qualcomm
chips. The blacklisted interfaces are QMI/wwan.
Reported-by: Lars Melin <larsm17@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit dd6b48ecec2ea7d15f28d5e5474388681899a5e1 upstream.
Device interface layout:
0: ff/ff/ff - serial
1: ff/00/00 - serial AT+PPP
2: ff/ff/ff - QMI/wwan
3: 08/06/50 - storage
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 533b3994610f316e5cd61b56d0c4daa15c830f89 upstream.
Device interface layout:
0: ff/ff/ff - serial
1: ff/ff/ff - serial AT+PPP
2: 08/06/50 - storage
3: ff/ff/ff - serial
4: ff/ff/ff - QMI/wwan
Reported-by: Julio Araujo <julio.araujo@wllctel.com.br>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 5509076d1b4485ce9fb07705fcbcd2695907ab5b upstream.
During firmware download the device expects memory addresses in
big-endian byte order. As the wIndex parameter which hold the address is
sent in little-endian byte order regardless of host byte order, we need
to use swab16 rather than cpu_to_be16.
Also make sure to handle the struct ti_i2c_desc size parameter which is
returned in little-endian byte order.
Reported-by: Ludovic Drolez <ldrolez@debian.org>
Tested-by: Ludovic Drolez <ldrolez@debian.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 01bb59ebffdec314da8da66266edf29529372f9b upstream.
When CONFIG_PCI and CONFIG_PM are not selected, xhci.c gets this
warning:
drivers/usb/host/xhci.c:409:13: warning: ‘xhci_msix_sync_irqs’ defined
but not used [-Wunused-function]
Instead of creating nested #ifdefs, this patch fixes it by defining the
xHCI PCI stubs as inline.
This warning has been in since 3.2 kernel and was
caused by commit 421aa841a134f6a743111cf44d0c6d3b45e3cf8c
"usb/xhci: hide MSI code behind PCI bars", but wasn't noticed
until 3.13 when a configuration with these options was tried
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 1f81b6d22a5980955b01e08cf27fb745dc9b686f upstream.
We have observed a rare cycle state desync bug after Set TR Dequeue
Pointer commands on Intel LynxPoint xHCs (resulting in an endpoint that
doesn't fetch new TRBs and thus an unresponsive USB device). It always
triggers when a previous Set TR Dequeue Pointer command has set the
pointer to the final Link TRB of a segment, and then another URB gets
enqueued and cancelled again before it can be completed. Further
investigation showed that the xHC had returned the Link TRB in the TRB
Pointer field of the Transfer Event (CC == Stopped -- Length Invalid),
but when xhci_find_new_dequeue_state() later accesses the Endpoint
Context's TR Dequeue Pointer field it is set to the first TRB of the
next segment.
The driver expects those two values to be the same in this situation,
and uses the cycle state of the latter together with the address of the
former. This should be fine according to the XHCI specification, since
the endpoint ring should be stopped when returning the Transfer Event
and thus should not advance over the Link TRB before it gets restarted.
However, real-world XHCI implementations apparently don't really care
that much about these details, so the driver should follow a more
defensive approach to try to work around HC spec violations.
This patch removes the stopped_trb variable that had been used to store
the TRB Pointer from the last Transfer Event of a stopped TRB. Instead,
xhci_find_new_dequeue_state() now relies only on the Endpoint Context,
requiring a small amount of additional processing to find the virtual
address corresponding to the TR Dequeue Pointer. Some other parts of the
function were slightly rearranged to better fit into this model.
This patch should be backported to kernels as old as 2.6.31 that contain
the commit ae636747146ea97efa18e04576acd3416e2514f5 "USB: xhci: URB
cancellation support."
Signed-off-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit c4bedb77ec4cb42f37cae4cbfddda8283161f7c8 upstream.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 10164c2ad6d2c16809f6c09e278f946e47801b3a upstream.
Fix driver new_id sysfs-attribute removal deadlock by making sure to
not hold any locks that the attribute operations grab when removing the
attribute.
Specifically, usb_serial_deregister holds the table mutex when
deregistering the driver, which includes removing the new_id attribute.
This can lead to a deadlock as writing to new_id increments the
attribute's active count before trying to grab the same mutex in
usb_serial_probe.
The deadlock can easily be triggered by inserting a sleep in
usb_serial_deregister and writing the id of an unbound device to new_id
during module unload.
As the table mutex (in this case) is used to prevent subdriver unload
during probe, it should be sufficient to only hold the lock while
manipulating the usb-serial driver list during deregister. A racing
probe will then either fail to find a matching subdriver or fail to get
the corresponding module reference.
Since v3.15-rc1 this also triggers the following lockdep warning:
======================================================
[ INFO: possible circular locking dependency detected ]
3.15.0-rc2 #123 Tainted: G W
-------------------------------------------------------
modprobe/190 is trying to acquire lock:
(s_active#4){++++.+}, at: [<c0167aa0>] kernfs_remove_by_name_ns+0x4c/0x94
but task is already holding lock:
(table_lock){+.+.+.}, at: [<bf004d84>] usb_serial_deregister+0x3c/0x78 [usbserial]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (table_lock){+.+.+.}:
[<c0075f84>] __lock_acquire+0x1694/0x1ce4
[<c0076de8>] lock_acquire+0xb4/0x154
[<c03af3cc>] _raw_spin_lock+0x4c/0x5c
[<c02bbc24>] usb_store_new_id+0x14c/0x1ac
[<bf007eb4>] new_id_store+0x68/0x70 [usbserial]
[<c025f568>] drv_attr_store+0x30/0x3c
[<c01690e0>] sysfs_kf_write+0x5c/0x60
[<c01682c0>] kernfs_fop_write+0xd4/0x194
[<c010881c>] vfs_write+0xbc/0x198
[<c0108e4c>] SyS_write+0x4c/0xa0
[<c000f880>] ret_fast_syscall+0x0/0x48
-> #0 (s_active#4){++++.+}:
[<c03a7a28>] print_circular_bug+0x68/0x2f8
[<c0076218>] __lock_acquire+0x1928/0x1ce4
[<c0076de8>] lock_acquire+0xb4/0x154
[<c0166b70>] __kernfs_remove+0x254/0x310
[<c0167aa0>] kernfs_remove_by_name_ns+0x4c/0x94
[<c0169fb8>] remove_files.isra.1+0x48/0x84
[<c016a2fc>] sysfs_remove_group+0x58/0xac
[<c016a414>] sysfs_remove_groups+0x34/0x44
[<c02623b8>] driver_remove_groups+0x1c/0x20
[<c0260e9c>] bus_remove_driver+0x3c/0xe4
[<c026235c>] driver_unregister+0x38/0x58
[<bf007fb4>] usb_serial_bus_deregister+0x84/0x88 [usbserial]
[<bf004db4>] usb_serial_deregister+0x6c/0x78 [usbserial]
[<bf005330>] usb_serial_deregister_drivers+0x2c/0x4c [usbserial]
[<bf016618>] usb_serial_module_exit+0x14/0x1c [sierra]
[<c009d6cc>] SyS_delete_module+0x184/0x210
[<c000f880>] ret_fast_syscall+0x0/0x48
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(table_lock);
lock(s_active#4);
lock(table_lock);
lock(s_active#4);
*** DEADLOCK ***
1 lock held by modprobe/190:
#0: (table_lock){+.+.+.}, at: [<bf004d84>] usb_serial_deregister+0x3c/0x78 [usbserial]
stack backtrace:
CPU: 0 PID: 190 Comm: modprobe Tainted: G W 3.15.0-rc2 #123
[<c0015e10>] (unwind_backtrace) from [<c0013728>] (show_stack+0x20/0x24)
[<c0013728>] (show_stack) from [<c03a9a54>] (dump_stack+0x24/0x28)
[<c03a9a54>] (dump_stack) from [<c03a7cac>] (print_circular_bug+0x2ec/0x2f8)
[<c03a7cac>] (print_circular_bug) from [<c0076218>] (__lock_acquire+0x1928/0x1ce4)
[<c0076218>] (__lock_acquire) from [<c0076de8>] (lock_acquire+0xb4/0x154)
[<c0076de8>] (lock_acquire) from [<c0166b70>] (__kernfs_remove+0x254/0x310)
[<c0166b70>] (__kernfs_remove) from [<c0167aa0>] (kernfs_remove_by_name_ns+0x4c/0x94)
[<c0167aa0>] (kernfs_remove_by_name_ns) from [<c0169fb8>] (remove_files.isra.1+0x48/0x84)
[<c0169fb8>] (remove_files.isra.1) from [<c016a2fc>] (sysfs_remove_group+0x58/0xac)
[<c016a2fc>] (sysfs_remove_group) from [<c016a414>] (sysfs_remove_groups+0x34/0x44)
[<c016a414>] (sysfs_remove_groups) from [<c02623b8>] (driver_remove_groups+0x1c/0x20)
[<c02623b8>] (driver_remove_groups) from [<c0260e9c>] (bus_remove_driver+0x3c/0xe4)
[<c0260e9c>] (bus_remove_driver) from [<c026235c>] (driver_unregister+0x38/0x58)
[<c026235c>] (driver_unregister) from [<bf007fb4>] (usb_serial_bus_deregister+0x84/0x88 [usbserial])
[<bf007fb4>] (usb_serial_bus_deregister [usbserial]) from [<bf004db4>] (usb_serial_deregister+0x6c/0x78 [usbserial])
[<bf004db4>] (usb_serial_deregister [usbserial]) from [<bf005330>] (usb_serial_deregister_drivers+0x2c/0x4c [usbserial])
[<bf005330>] (usb_serial_deregister_drivers [usbserial]) from [<bf016618>] (usb_serial_module_exit+0x14/0x1c [sierra])
[<bf016618>] (usb_serial_module_exit [sierra]) from [<c009d6cc>] (SyS_delete_module+0x184/0x210)
[<c009d6cc>] (SyS_delete_module) from [<c000f880>] (ret_fast_syscall+0x0/0x48)
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 895d240d1db0b2736d779200788e4c4aea28a0c6 upstream.
By specifying NO_UNION_NORMAL the ACM driver does only use the first two
USB interfaces (modem data & control). The AT Port, Diagnostic and NMEA
interfaces are left to the USB serial driver.
Signed-off-by: Michael Ulbricht <michael.ulbricht@systec-electronic.com>
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit b16c02fbfb963fa2941b7517ebf1f8a21946775e upstream.
Add device ids to pl2303 for the Hewlett-Packard HP POS pole displays:
LD960: 03f0:0B39
LCM220: 03f0:3139
LCM960: 03f0:3239
[ Johan: fix indentation and sort PIDs numerically ]
Signed-off-by: Aaron Sanders <aaron.sanders@hp.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 72b3007951010ce1bbf950e23b19d9839fa905a5 upstream.
Signed-off-by: Tristan Bruns <tristan@tristanbruns.de>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit d6de486bc22255779bd54b0fceb4c240962bf146 upstream.
option driver, added VID/PID for Telit UE910v2 modem
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 2e01280d2801c72878cf3a7119eac30077b463d5 upstream.
This reverts commit 1ebca9dad5abe8b2ed4dbd186cd657fb47c1f321.
This device was erroneously added to the sierra driver even though it's
not a Sierra device and was already handled by the option driver.
Cc: Richard Farina <sidhayn@gmail.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit efe26e16b1d93ac0085e69178cc18811629e8fc5 upstream.
Custom VID/PIDs for Brainboxes cards as reported in
https://bugzilla.redhat.com/show_bug.cgi?id=1071914
Signed-off-by: Michele Baldessari <michele@acksyn.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit d8eb6c653ef6b323d630de3c5685478469e248bc upstream.
commit 511f3c5 (usb: gadget: udc-core: fix a regression during gadget driver
unbinding) introduced a crash when DEBUG is enabled.
The debug trace in the atmel_usba_stop function made the assumption that the
driver pointer passed in parameter was not NULL, but since the commit above,
such assumption was no longer always true.
This commit now uses the driver pointer stored in udc which fixes this
issue.
[ balbi@ti.com : improved commit log a bit ]
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 06f9b6e59661cee510b04513b13ea7927727d758 upstream.
Around DWC USB3 2.30a release another bit has been added to the
Device-Specific Event (DEVT) Event Information (EvtInfo) bitfield.
Because of that, what used to be 8 bits long, has become 9 bits long.
Per dwc3 2.30a+ spec in the Device-Specific Event (DEVT), the field of
Event Information Bits(EvtInfo) uses [24:16] bits, and it has 9 bits
not 8 bits. And the following reserved field uses [31:25] bits not
[31:24] bits, and it has 7 bits.
So in dwc3_event_devt, the bit mask should be:
event_info [24:16] 9 bits
reserved31_25 [31:25] 7 bits
This patch makes sure that newer core releases will work fine with
Linux and that we will decode the event information properly on new
core releases.
[ balbi@ti.com : improve commit log a bit ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit d86db25e53fa69e3e97f3b55dd82a70689787c5d upstream.
The DELAY_INIT quirk only reduces the frequency of enumeration failures
with the Logitech HD Pro C920 and C930e webcams, but does not quite
eliminate them. We have found that adding a delay of 100ms between the
first and second Get Configuration request makes the device enumerate
perfectly reliable even after several weeks of extensive testing. The
reasons for that are anyone's guess, but since the DELAY_INIT quirk
already delays enumeration by a whole second, wating for another 10th of
that isn't really a big deal for the one other device that uses it, and
it will resolve the problems with these webcams.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit e0429362ab15c46ea4d64c3f8c9e0933e48a143a upstream.
We've encountered a rare issue when enumerating two Logitech webcams
after a reboot that doesn't power cycle the USB ports. They are spewing
random data (possibly some leftover UVC buffers) on the second
(full-sized) Get Configuration request of the enumeration phase. Since
the data is random this can potentially cause all kinds of odd behavior,
and since it occasionally happens multiple times (after the kernel
issues another reset due to the garbled configuration descriptor), it is
not always recoverable. Set the USB_DELAY_INIT quirk that seems to work
around the issue.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit a1227f3c1030e96ebc51d677d2f636268845c5fb upstream.
ehci_irq() and ehci_hrtimer_func() can deadlock on ehci->lock when
threadirqs option is used. To prevent the deadlock use
spin_lock_irqsave() in ehci_irq().
This change can be reverted when hrtimer callbacks become threaded.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 6dbd46c849e071e6afc1e0cad489b0175bca9318 upstream.
Hello,
the following patch adds an entry for the PID of a Cressi Leonardo
diving computer interface to kernel 3.13.0.
It is detected as FT232RL.
Works with subsurface.
Signed-off-by: Joerg Dorchain <joerg@dorchain.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit e1466ad5b1aeda303f9282463d55798d2eda218c upstream.
Custom VID/PID for Z3X Box device, popular tool for cellphone flashing.
Signed-off-by: Alexey E. Kramarenko <alexeyk13@yandex.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 12df84d4a80278a5b1abfec3206795291da52fc9 upstream.
This interface is to be handled by the qmi_wwan driver.
CC: Hans-Christoph Schemmel <hans-christoph.schemmel@gemalto.com>
CC: Christian Schmiedl <christian.schmiedl@gemalto.com>
CC: Nicolaus Colberg <nicolaus.colberg@gemalto.com>
CC: David McCullough <david.mccullough@accelecon.com>
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 3e8d6d85adedc59115a564c0a54b36e42087c4d9 upstream.
High-speed USB connections revert back to full-speed signalling when
the device goes into suspend. This takes several milliseconds, and
during that time it's not possible to tell reliably whether the device
has been disconnected.
On some platforms, the Wake-On-Disconnect circuitry gets confused
during this intermediate state. It generates a false wakeup signal,
which can prevent the controller from going to sleep.
To avoid this problem, this patch adds a 5-ms delay to the
ehci_bus_suspend() routine if any ports have to switch over to
full-speed signalling. (Actually, the delay was already present for
devices using a particular kind of PHY power management; the patch
merely causes the delay to be used more widely.)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Peter Chen <Peter.Chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2:
- Adjust context
- s/has_tdi_phy_lpm/has_hostpc/
- Always re-lock ehci->lock after the sleep]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 3635c7e2d59f7861afa6fa5e87e2a58860ff514d upstream.
Interface #5 of 19d2:1270 is a net interface which has been submitted to the
qmi_wwan driver so consequently remove it from the option driver.
Signed-off-by: Raymond Wanyoike <raymond.wanyoike@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 76f24e3f39a1a94bab0d54e98899d64abcd9f69c upstream.
Adding two more IDs to the ftdi_sio usb serial driver.
It now connects Tagsys RFID readers.
There might be more IDs out there for other Tagsys models.
Signed-off-by: Ulrich Hahn <uhahn@eanco.de>
Cc: Johan Hovold <johan@hovold.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
