| Age | Commit message (Collapse) | Author |
|---|
|
[Not upstream s it was fixed differently there for 3.3 with a much more
"intrusive" rework of the driver - gregkh]
There is a race condition involving acm_tty_hangup() and acm_tty_close()
where hangup() would attempt to access tty->driver_data without proper
locking and NULL checking after close() has potentially already set it
to NULL. One possibility to (sporadically) trigger this behavior is to
perform a suspend/resume cycle with a running WWAN data connection.
This patch addresses the issue by introducing a NULL check for
tty->driver_data in acm_tty_hangup() protected by open_mutex and exiting
gracefully when hangup() is invoked on a device that has already been
closed.
Signed-off-by: Thilo-Alexander Ginkel <thilo@ginkel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit c61875977458637226ab093a35d200f2d5789787 upstream.
Problems with NVIDIA's OHCI host controllers persist. After looking
carefully through the spec, I finally realized that when a controller
is reset it then automatically goes into a SUSPEND state in which it
is completely quiescent (no DMA and no IRQs) and from which it will
not awaken until the system puts it into the OPERATIONAL state.
Therefore there's no need to worry about controllers being in the
RESET state for extended periods, or remaining in the OPERATIONAL
state during system shutdown. The proper action for device
initialization is to put the controller into the RESET state (if it's
not there already) and then to issue a software reset. Similarly, the
proper action for device shutdown is simply to do a software reset.
This patch (as1499) implements such an approach. It simplifies
initialization and shutdown, and allows the NVIDIA shutdown-quirk code
to be removed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Andre "Osku" Schmidt <andre.osku.schmidt@googlemail.com>
Tested-by: Arno Augustin <Arno.Augustin@web.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 18b7ede5f7ee2092aedcb578d3ac30bd5d4fc23c upstream.
[ removed the dwc3 portion of the patch as it didn't apply to
older kernels - gregkh]
According to USB 3.0 Specification Table 9-22, if
bmAttributes [4:0] are set to zero, it means "no
streams supported", but the way this helper was
defined on Linux, we will *always* have one stream
which might cause several problems.
For example on DWC3, we would tell the controller
endpoint has streams enabled and yet start transfers
with Stream ID set to 0, which would goof up the host
side.
While doing that, convert the macro to an inline
function due to the different checks we now need.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 3c8c9316710b83e906e425024153bf0929887b59 upstream.
Add support for Chinese Noname HSPA USB modem which is apparently
manufactured by a company called ZD Incorporated (based on texts in the
Windows drivers).
This product is available at least from Dealextreme (SKU 80032) and
possibly in India with name Olive V-MW250. It is based on Qualcomm
MSM6280 chip.
I needed to also add "options usb-storage quirks=0685:7000:i" in modprobe
configuration because udevd or the kernel keeps poking the embedded
fake-cd-rom which fails and causes the device to reset. There might be
a better way to accomplish the same. usb_modeswitch is not needed with
this device.
Signed-off-by: Janne Snabb <snabb@epipe.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 5b061623355d8f69327a24838b0aa05e435ae5d5 upstream.
Add VendorID/ProductID for USB 3G dongle Model VT1000 of Viettel.
Signed-off-by: VU Tuan Duc <ducvt@viettel.com.vn>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 71d85724bdd947a3b42a88d08af79f290a1a767b upstream.
I encountered a result of COMP_2ND_BW_ERR while improving how the pwc
webcam driver handles not having the full usb1 bandwidth available to
itself.
I created the following test setup, a NEC xhci controller with a
single TT USB 2 hub plugged into it, with a usb keyboard and a pwc webcam
plugged into the usb2 hub. This caused the following to show up in dmesg
when trying to stream from the pwc camera at its highest alt setting:
xhci_hcd 0000:01:00.0: ERROR: unexpected command completion code 0x23.
usb 6-2.1: Not enough bandwidth for altsetting 9
And usb_set_interface returned -EINVAL, which caused my pwc code to not
do the right thing as it expected -ENOSPC.
This patch makes the xhci driver properly handle COMP_2ND_BW_ERR and makes
usb_set_interface return -ENOSPC as expected.
This should be backported to stable kernels as old as 2.6.32.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit bc677d5b64644c399cd3db6a905453e611f402ab upstream.
Add a new field num_mapped_sgs to struct urb so that we have a place to
store the number of mapped entries and can also retain the original
value of entries in num_sgs. Previously, usb_hcd_map_urb_for_dma()
would overwrite this with the number of mapped entries, which would
break dma_unmap_sg() because it requires the original number of entries.
This fixes warnings like the following when using USB storage devices:
------------[ cut here ]------------
WARNING: at lib/dma-debug.c:902 check_unmap+0x4e4/0x695()
ehci_hcd 0000:00:12.2: DMA-API: device driver frees DMA sg list with different entry count [map count=4] [unmap count=1]
Modules linked in: ohci_hcd ehci_hcd
Pid: 0, comm: kworker/0:1 Not tainted 3.2.0-rc2+ #319
Call Trace:
<IRQ> [<ffffffff81036d3b>] warn_slowpath_common+0x80/0x98
[<ffffffff81036de7>] warn_slowpath_fmt+0x41/0x43
[<ffffffff811fa5ae>] check_unmap+0x4e4/0x695
[<ffffffff8105e92c>] ? trace_hardirqs_off+0xd/0xf
[<ffffffff8147208b>] ? _raw_spin_unlock_irqrestore+0x33/0x50
[<ffffffff811fa84a>] debug_dma_unmap_sg+0xeb/0x117
[<ffffffff8137b02f>] usb_hcd_unmap_urb_for_dma+0x71/0x188
[<ffffffff8137b166>] unmap_urb_for_dma+0x20/0x22
[<ffffffff8137b1c5>] usb_hcd_giveback_urb+0x5d/0xc0
[<ffffffffa0000d02>] ehci_urb_done+0xf7/0x10c [ehci_hcd]
[<ffffffffa0001140>] qh_completions+0x429/0x4bd [ehci_hcd]
[<ffffffffa000340a>] ehci_work+0x95/0x9c0 [ehci_hcd]
...
---[ end trace f29ac88a5a48c580 ]---
Mapped at:
[<ffffffff811faac4>] debug_dma_map_sg+0x45/0x139
[<ffffffff8137bc0b>] usb_hcd_map_urb_for_dma+0x22e/0x478
[<ffffffff8137c494>] usb_hcd_submit_urb+0x63f/0x6fa
[<ffffffff8137d01c>] usb_submit_urb+0x2c7/0x2de
[<ffffffff8137dcd4>] usb_sg_wait+0x55/0x161
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 08e87d0d773dc9ca5faf4c3306e238ed0ea129b0 upstream.
Hi, below patch adds the USB-ID of the serial adapters sold by
Multiplex RC (www.multiplex-rc.de).
Signed-off-by: Malte Schröder <maltesch@gmx.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 694c6301e515bad574af74b6552134c4d9dcb334 upstream.
Fix regression introduced by commit 507ca9bc047666 ([PATCH] USB: add
ability for usb-serial drivers to determine if their write urb is
currently being used.) which inverted the logic in write_room so that it
returns zero when the write urb is actually free.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 772aed45b604c5ff171f0f12c12392d868333f79 upstream.
In musb_init_controller() there's a pm_runtime_put(), but there's no
pm_runtime_get(), which creates a mismatch that causes the driver to
sleep when it shouldn't.
This was introduced in 7acc619[1], but it wasn't triggered in my setup
until 18a2689[2] was merged to Linus' branch at point df0914[3]. IOW;
when PM is working as it was supposed to.
However, it seems most of the time this is used in a way that keeps the
counter above 0, so nobody noticed. Also, it seems to depend on the
configuration used in versions before 3.1, but not later (or in it).
I found the problem by loading isp1704_charger before any usb gadgets:
http://article.gmane.org/gmane.linux.kernel/1226122
All versions after 2.6.39 are affected.
[1] usb: musb: Idle path retention and offmode support for OMAP3
[2] OMAP2+: musb: hwmod adaptation for musb registration
[3] Merge branch 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6
Cc: Hema HK <hemahk@ti.com>
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
commit 35284b3d2f68a8a3703745e629999469f78386b5 upstream.
The Guillemot Webcam Hercules Dualpix Exchange camera
has been reported with a second ID.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
the feature to fix an oops
commit 1a3a026ba1b6bbfe0b7f79ab38cf991d691e7c9a upstream.
Echo vendor and product number of a non usb-storage device to
usb-storage driver's new_id, then plug in the device to host and you
will find following oops msg, the root cause is usb_stor_probe1()
refers invalid id entry if giving a dynamic id, so just disable the
feature.
[ 3105.018012] general protection fault: 0000 [#1] SMP DEBUG_PAGEALLOC
[ 3105.018062] CPU 0
[ 3105.018075] Modules linked in: usb_storage usb_libusual bluetooth
dm_crypt binfmt_misc snd_hda_codec_analog snd_hda_intel snd_hda_codec
snd_hwdep hp_wmi ppdev sparse_keymap snd_pcm snd_seq_midi snd_rawmidi
snd_seq_midi_event snd_seq snd_timer snd_seq_device psmouse snd
serio_raw tpm_infineon soundcore i915 snd_page_alloc tpm_tis
parport_pc tpm tpm_bios drm_kms_helper drm i2c_algo_bit video lp
parport usbhid hid sg sr_mod sd_mod ehci_hcd uhci_hcd usbcore e1000e
usb_common floppy
[ 3105.018408]
[ 3105.018419] Pid: 189, comm: khubd Tainted: G I 3.2.0-rc7+
#29 Hewlett-Packard HP Compaq dc7800p Convertible Minitower/0AACh
[ 3105.018481] RIP: 0010:[<ffffffffa045830d>] [<ffffffffa045830d>]
usb_stor_probe1+0x2fd/0xc20 [usb_storage]
[ 3105.018536] RSP: 0018:ffff880056a3d830 EFLAGS: 00010286
[ 3105.018562] RAX: ffff880065f4e648 RBX: ffff88006bb28000 RCX: 0000000000000000
[ 3105.018597] RDX: ffff88006f23c7b0 RSI: 0000000000000001 RDI: 0000000000000206
[ 3105.018632] RBP: ffff880056a3d900 R08: 0000000000000000 R09: ffff880067365000
[ 3105.018665] R10: 00000000000002ac R11: 0000000000000010 R12: ffff6000b41a7340
[ 3105.018698] R13: ffff880065f4ef60 R14: ffff88006bb28b88 R15: ffff88006f23d270
[ 3105.018733] FS: 0000000000000000(0000) GS:ffff88007a200000(0000)
knlGS:0000000000000000
[ 3105.018773] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
[ 3105.018801] CR2: 00007fc99c8c4650 CR3: 0000000001e05000 CR4: 00000000000006f0
[ 3105.018835] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 3105.018870] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
[ 3105.018906] Process khubd (pid: 189, threadinfo ffff880056a3c000,
task ffff88005677a400)
[ 3105.018945] Stack:
[ 3105.018959] 0000000000000000 0000000000000000 ffff880056a3d8d0
0000000000000002
[ 3105.019011] 0000000000000000 ffff880056a3d918 ffff880000000000
0000000000000002
[ 3105.019058] ffff880056a3d8d0 0000000000000012 ffff880056a3d8d0
0000000000000006
[ 3105.019105] Call Trace:
[ 3105.019128] [<ffffffffa0458cd4>] storage_probe+0xa4/0xe0 [usb_storage]
[ 3105.019173] [<ffffffffa0097822>] usb_probe_interface+0x172/0x330 [usbcore]
[ 3105.019211] [<ffffffff815fda67>] driver_probe_device+0x257/0x3b0
[ 3105.019243] [<ffffffff815fdd43>] __device_attach+0x73/0x90
[ 3105.019272] [<ffffffff815fdcd0>] ? __driver_attach+0x110/0x110
[ 3105.019303] [<ffffffff815fb93c>] bus_for_each_drv+0x9c/0xf0
[ 3105.019334] [<ffffffff815fd6c7>] device_attach+0xf7/0x120
[ 3105.019364] [<ffffffff815fc905>] bus_probe_device+0x45/0x80
[ 3105.019396] [<ffffffff815f98a6>] device_add+0x876/0x990
[ 3105.019434] [<ffffffffa0094e42>] usb_set_configuration+0x822/0x9e0 [usbcore]
[ 3105.019479] [<ffffffffa00a3492>] generic_probe+0x62/0xf0 [usbcore]
[ 3105.019518] [<ffffffffa0097a46>] usb_probe_device+0x66/0xb0 [usbcore]
[ 3105.019555] [<ffffffff815fda67>] driver_probe_device+0x257/0x3b0
[ 3105.019589] [<ffffffff815fdd43>] __device_attach+0x73/0x90
[ 3105.019617] [<ffffffff815fdcd0>] ? __driver_attach+0x110/0x110
[ 3105.019648] [<ffffffff815fb93c>] bus_for_each_drv+0x9c/0xf0
[ 3105.019680] [<ffffffff815fd6c7>] device_attach+0xf7/0x120
[ 3105.019709] [<ffffffff815fc905>] bus_probe_device+0x45/0x80
[ 3105.021040] usb usb6: usb auto-resume
[ 3105.021045] usb usb6: wakeup_rh
[ 3105.024849] [<ffffffff815f98a6>] device_add+0x876/0x990
[ 3105.025086] [<ffffffffa0088987>] usb_new_device+0x1e7/0x2b0 [usbcore]
[ 3105.025086] [<ffffffffa008a4d7>] hub_thread+0xb27/0x1ec0 [usbcore]
[ 3105.025086] [<ffffffff810d5200>] ? wake_up_bit+0x50/0x50
[ 3105.025086] [<ffffffffa00899b0>] ? usb_remote_wakeup+0xa0/0xa0 [usbcore]
[ 3105.025086] [<ffffffff810d49b8>] kthread+0xd8/0xf0
[ 3105.025086] [<ffffffff81939884>] kernel_thread_helper+0x4/0x10
[ 3105.025086] [<ffffffff8192a8c0>] ? _raw_spin_unlock_irq+0x50/0x80
[ 3105.025086] [<ffffffff8192b1b4>] ? retint_restore_args+0x13/0x13
[ 3105.025086] [<ffffffff810d48e0>] ? __init_kthread_worker+0x80/0x80
[ 3105.025086] [<ffffffff81939880>] ? gs_change+0x13/0x13
[ 3105.025086] Code: 00 48 83 05 cd ad 00 00 01 48 83 05 cd ad 00 00
01 4c 8b ab 30 0c 00 00 48 8b 50 08 48 83 c0 30 48 89 45 a0 4c 89 a3
40 0c 00 00 <41> 0f b6 44 24 10 48 89 55 a8 3c ff 0f 84 b8 04 00 00 48
83 05
[ 3105.025086] RIP [<ffffffffa045830d>] usb_stor_probe1+0x2fd/0xc20
[usb_storage]
[ 3105.025086] RSP <ffff880056a3d830>
[ 3105.060037] hub 6-0:1.0: hub_resume
[ 3105.062616] usb usb5: usb auto-resume
[ 3105.064317] ehci_hcd 0000:00:1d.7: resume root hub
[ 3105.094809] ---[ end trace a7919e7f17c0a727 ]---
[ 3105.130069] hub 5-0:1.0: hub_resume
[ 3105.132131] usb usb4: usb auto-resume
[ 3105.132136] usb usb4: wakeup_rh
[ 3105.180059] hub 4-0:1.0: hub_resume
[ 3106.290052] usb usb6: suspend_rh (auto-stop)
[ 3106.290077] usb usb4: suspend_rh (auto-stop)
Signed-off-by: Huajun Li <huajun.li.lee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 59bf5cf94f0fa3b08fb1258b52649077b7d0914d upstream.
We were sending data on the stack when uploading firmware, which causes
some machines fits, and is not allowed. Fix this by using the buffer we
already had around for this very purpose.
Reported-by: Wouter M. Koolen <wmkoolen@cwi.nl>
Tested-by: Wouter M. Koolen <wmkoolen@cwi.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit e7c8e8605d0bafc705ff27f9da98a1668427cc0f upstream.
On some failures, the country_code field of an acm structure is freed
without freeing the acm structure itself. Elsewhere, operations including
memcpy and kfree are performed on the country_code field. The patch sets
the country_code field to NULL when it is freed, and likewise sets the
country_code_size field to 0.
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 02a551c9755b799579e0a093bcc99b80b4dc1453 upstream.
Huawei use the product code HUAWEI_PRODUCT_E353 (0x1506) for a
number of different devices, which each can appear with a number
of different descriptor sets. Different types of interfaces
can be identified by looking at the subclass and protocol fields
Subclass 1 protocol 8 is actually the data interface of a CDC
ECM set, with subclass 1 protocol 9 as the control interface.
Neither support serial data communcation, and cannot therefore
be supported by this driver.
At the same time, add a few other sets which appear if the
device is configured in "Windows mode" using this modeswitch
message:
55534243000000000000000000000011060000000100000000000000000000
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 414b591fd16655871e9f5592a55368b10a3ccc30 upstream.
This patch adds the controlling interfaces for the Huawei E398.
Thanks to Bjørn Mork <bjorn@mork.no> for extracting the interface
numbers from the windows driver.
Signed-off-by: Alex Hermann <alex@wenlex.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 6abff5dc4d5a2c90e597137ce8987e7fd439259b upstream.
Add USB IDs for Motorola H24 HSPA USB module.
Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 158886cd2cf4599e04f9b7e10cb767f5f39b14f1 upstream.
When system enters suspend, xHCI driver clears command ring by writing zero
to all the TRBs. However, this also writes zero to the Link TRB, and the ring
is mangled. This may cause driver accesses wrong memory address and the
result is unpredicted.
When clear the command ring, keep the last Link TRB intact, only clear its
cycle bit. This should fix the "command ring full" issue reported by Oliver
Neukum.
This should be backported to stable kernels as old as 2.6.37, since the
commit 89821320 "xhci: Fix command ring replay after resume" is merged.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit e3420901eba65b1c46bed86d360e3a8685d20734 upstream.
Fix a regression that was introduced by commit
811c926c538f7e8d3c08b630dd5844efd7e000f6 (USB: EHCI: fix HUB TT scheduling
issue with iso transfer).
We detect an error if next == start, but this means uframe 0 can't be allocated
anymore for iso transfer...
Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 811c926c538f7e8d3c08b630dd5844efd7e000f6 upstream.
The current TT scheduling doesn't allow to play and then record on a
full-speed device connected to a high speed hub.
The IN iso stream can only start on the first uframe (0-2 for a 165 us)
because of CSPLIT transactions.
For the OUT iso stream there no such restriction. uframe 0-5 are possible.
The idea of this patch is that the first uframe are precious (for IN TT iso
stream) and we should allocate the last uframes first if possible.
For that we reverse the order of uframe allocation (last uframe first).
Here an example :
hid interrupt stream
----------------------------------------------------------------------
uframe | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 |
----------------------------------------------------------------------
max_tt_usecs | 125 | 125 | 125 | 125 | 125 | 125 | 30 | 0 |
----------------------------------------------------------------------
used usecs on a frame | 13 | 0 | 0 | 0 | 0 | 0 | 0 | 0 |
----------------------------------------------------------------------
iso OUT stream
----------------------------------------------------------------------
uframe | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 |
----------------------------------------------------------------------
max_tt_usecs | 125 | 125 | 125 | 125 | 125 | 125 | 30 | 0 |
----------------------------------------------------------------------
used usecs on a frame | 13 | 125 | 39 | 0 | 0 | 0 | 0 | 0 |
----------------------------------------------------------------------
There no place for iso IN stream (uframe 0-2 are used) and we got "cannot
submit datapipe for urb 0, error -28: not enough bandwidth" error.
With the patch this become.
iso OUT stream
----------------------------------------------------------------------
uframe | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 |
----------------------------------------------------------------------
max_tt_usecs | 125 | 125 | 125 | 125 | 125 | 125 | 30 | 0 |
----------------------------------------------------------------------
used usecs on a frame | 13 | 0 | 0 | 0 | 125 | 39 | 0 | 0 |
----------------------------------------------------------------------
iso IN stream
----------------------------------------------------------------------
uframe | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 |
----------------------------------------------------------------------
max_tt_usecs | 125 | 125 | 125 | 125 | 125 | 125 | 30 | 0 |
----------------------------------------------------------------------
used usecs on a frame | 13 | 0 | 125 | 40 | 125 | 39 | 0 | 0 |
----------------------------------------------------------------------
Signed-off-by: Matthieu Castet <matthieu.castet@parrot.com>
Signed-off-by: Thomas Poussevin <thomas.poussevin@parrot.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit cec28a5428793b6bc64e56687fb239759d6da74e upstream.
Kingston DT 101 G2 replies a wrong tag while transporting, add an
unusal_devs entry to ignore the tag validation.
Signed-off-by: Qinglin Ye <yestyle@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit ec0cd94d881ca89cc9fb61d00d0f4b2b52e605b3 upstream.
Tested with SIM5218EVB-KIT evaluation kit.
Signed-off-by: Veli-Pekka Peltola <veli-pekka.peltola@bluegiga.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 46b1848360c8e634e0b063932a1261062fa0f7d6 upstream.
This patch creates the missing controlling devices for the Huawei E353
HSPA+ stick.
Signed-off-by: Dirk Nehring <dnehring@gmx.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 307369b0ca06b27b511b61714e335ddfccf19c4f upstream.
Signed-off-by: Marcin Kościelnicki <koriakin@0x04.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 8746c83d538cab273d335acb2be226d096f4a5af upstream.
qset->qh.link is an __le64 field and we should be using cpu_to_le64()
to fill it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 5d193ce8f1fa7c67c7fd7be2c03ef31eed344a4f upstream.
Currently the driver tries to save context in the suspend path, but
will cause an abort if the device is already runtime suspended. This
happens, for example, if MUSB loaded/compiled-in, in host mode, but no
USB devices are attached. MUSB will be runtime suspended, but then
attempting a system suspend will crash due to the context save
being attempted while the device is disabled.
On OMAP, as of v3.1, the driver's ->runtime_suspend() callback will be
called late in the suspend path (by the PM domain layer) if the driver
is not already runtime suspended, ensuring a full shutdown.
Therefore, the context save is not needed in the ->suspend() method
since it will be called in the ->runtime_suspend() method anyways
(similarily for resume.)
NOTE: this leaves the suspend/resume methods basically empty (with
some FIXMEs and comments, but I'll leave it to the maintainers
to decide whether to remove them.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This reverts commit f0cc710a6dec5b808a6f13f1f8853c094fce5f12.
Cc: Matthieu Castet <matthieu.castet@parrot.com>
Cc: Thomas Poussevin <thomas.poussevin@parrot.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 0d145d7d4a241c321c832a810bb6edad18e2217b upstream.
The following patch contains additional affected webcam models, on top of the
patches commited to linux-next 2394d67e446bf616a0885167d5f0d397bdacfdfc
and 5b253d88cc6c65a23cefc457a5a4ef139913c5fc
Signed-off-by: sordna <sordna@gmail.com>
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 60c71ca972a2dd3fd9d0165b405361c8ad48349b upstream.
We've had another report of the "chipmunk" sound on a Logitech C600 webcam.
This patch resolves the issue.
Signed-off-by: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 811c926c538f7e8d3c08b630dd5844efd7e000f6 upstream.
The current TT scheduling doesn't allow to play and then record on a
full-speed device connected to a high speed hub.
The IN iso stream can only start on the first uframe (0-2 for a 165 us)
because of CSPLIT transactions.
For the OUT iso stream there no such restriction. uframe 0-5 are possible.
The idea of this patch is that the first uframe are precious (for IN TT iso
stream) and we should allocate the last uframes first if possible.
For that we reverse the order of uframe allocation (last uframe first).
Here an example :
hid interrupt stream
----------------------------------------------------------------------
uframe | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 |
----------------------------------------------------------------------
max_tt_usecs | 125 | 125 | 125 | 125 | 125 | 125 | 30 | 0 |
----------------------------------------------------------------------
used usecs on a frame | 13 | 0 | 0 | 0 | 0 | 0 | 0 | 0 |
----------------------------------------------------------------------
iso OUT stream
----------------------------------------------------------------------
uframe | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 |
----------------------------------------------------------------------
max_tt_usecs | 125 | 125 | 125 | 125 | 125 | 125 | 30 | 0 |
----------------------------------------------------------------------
used usecs on a frame | 13 | 125 | 39 | 0 | 0 | 0 | 0 | 0 |
----------------------------------------------------------------------
There no place for iso IN stream (uframe 0-2 are used) and we got "cannot
submit datapipe for urb 0, error -28: not enough bandwidth" error.
With the patch this become.
iso OUT stream
----------------------------------------------------------------------
uframe | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 |
----------------------------------------------------------------------
max_tt_usecs | 125 | 125 | 125 | 125 | 125 | 125 | 30 | 0 |
----------------------------------------------------------------------
used usecs on a frame | 13 | 0 | 0 | 0 | 125 | 39 | 0 | 0 |
----------------------------------------------------------------------
iso IN stream
----------------------------------------------------------------------
uframe | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 |
----------------------------------------------------------------------
max_tt_usecs | 125 | 125 | 125 | 125 | 125 | 125 | 30 | 0 |
----------------------------------------------------------------------
used usecs on a frame | 13 | 0 | 125 | 40 | 125 | 39 | 0 | 0 |
----------------------------------------------------------------------
Signed-off-by: Matthieu Castet <matthieu.castet@parrot.com>
Signed-off-by: Thomas Poussevin <thomas.poussevin@parrot.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 2f640bf4c94324aeaa1b6385c10aab8c5ad1e1cf upstream.
The 8020i protocol (also 8070i and QIC-157) uses 12-byte commands;
shorter commands must be padded. Simon Detheridge reports that his
3-TB USB disk drive claims to use the 8020i protocol (which is
normally meant for ATAPI devices like CD drives), and because of its
large size, the disk drive requires the use of 16-byte commands.
However the usb_stor_pad12_command() routine in usb-storage always
sets the command length to 12, making the drive impossible to use.
Since the SFF-8020i specification allows for 16-byte commands in
future extensions, we may as well accept them. This patch (as1490)
changes usb_stor_pad12_command() to leave commands larger than 12
bytes alone rather than truncating them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Simon Detheridge <simon@widgit.com>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit b1ffb4c851f185e9051ba837c16d9b84ef688d26 upstream.
Fix for ftdi_set_termios() glitching output
ftdi_set_termios() is constantly setting the baud rate, data bits and parity
unnecessarily on every call, . When called while characters are being
transmitted can cause the FTDI chip to corrupt the serial port bit stream
output by stalling the output half a bit during the output of a character.
Simple fix by skipping this setting if the baud rate/data bits/parity are
unchanged.
Signed-off-by: Andrew Worsley <amworsley@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 583182ba5f02c8c9be82ea550f2051eaec15b975 upstream.
This patch for the usb serial ark3116 driver fixes an initialisation
ordering bug that gets triggered on hotplug when using at least recent
debian/ubuntu userspace. Without it, ark3116 serial cables don't work.
Signed-off-by: Bart Hartgers <bart.hartgers@gmail.com>
Tested-by: law_ence.dev@ntlworld.com
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 97ff22ee3b4cb3a334f7385e269773141aed702f upstream.
This patch (as1491) works around a bug in GCC-3.4.6, which is still
supposed to be supported. The number of microseconds in the udelay()
call in quirk_usb_disable_ehci() is fixed at 100, but the compiler
doesn't understand this and generates a link-time error. So we
replace the otherwise unused variable "delta" with a simple constant
100. This same pattern is already used in other delay loops in that
source file.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Konrad Rzepecki <krzepecki@dentonet.pl>
Tested-by: Konrad Rzepecki <krzepecki@dentonet.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 5dc2470c602da8851907ec18942cd876c3b4ecc1 upstream.
There's a race between the USB disconnect handler and the TTY close
handler which may cause the acm object to be freed while it's still
being used. This may lead to things like
http://article.gmane.org/gmane.linux.usb.general/54250
and
https://lkml.org/lkml/2011/5/29/64
This is the simplest fix I could come up with. Holding on to open_mutex
while closing the TTY device prevents acm_disconnect() from freeing the
acm object between acm->port.count drops to 0 and the TTY side of the
cleanups are finalized.
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Cc: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 731ad81e2dd97e3f222361f7b3ff4b35639e46af upstream.
ML7831 is companion chip for Intel Atom E6xx series.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.lapis-semi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 0c16595539b612fe948559433dda08ff96a8bdc7 upstream.
I get report from customer that his usb-serial
converter doesn't work well,it sometimes work,
but sometimes it doesn't.
The usb-serial converter's id:
vendor_id product_id
0x4348 0x5523
Then I search the usb-serial codes, and there are
two drivers announce support this device, pl2303
and ch341, commit 026dfaf1 cause it. Through many
times to test, ch341 works well with this device,
and pl2303 doesn't work quite often(it just work quite little).
ch341 works well with this device, so we doesn't
need pl2303 to support.I try to revert 026dfaf1 first,
but it failed. So I prepare this patch by hand to revert it.
Signed-off-by: Wang YanQing <Udknight@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 4aa3648c719265bac9c2742c9ebb043e6dbdd790 upstream.
Signed-off-by: Ferenc Wagner <wferi@niif.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 46b5a277ed90317a4d17e936c16037e76011b219 upstream.
This patch adds new PIDs for ZTE 3G modem, after we confirm it and tested.
Thanks for Dan's work at kernel option devier.
Signed-off-by: Alvin.Zheng <zheng.zhijian@zte.com.cn>
Signed-off-by: wsalvin <wsalvin@yahoo.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit f69e3120df82391a0ee8118e0a156239a06b2afb upstream.
This patch (as1494) fixes a problem in xhci-hcd's resume routine.
When the controller is runtime-resumed, this can only mean that one of
the two root hubs has made a wakeup request and therefore needs to be
resumed as well. Rather than try to determine which root hub requires
attention (which might be difficult in the case where a new
non-SuperSpeed device has been plugged in), the patch simply resumes
both root hubs.
Without this change, there is a race: The controller might be put back
to sleep before it can activate its IRQ line, and the wakeup condition
might never get handled.
The patch also simplifies the logic in xhci_resume a little, combining
some repeated flag settings into a single pair of statements.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit f43d623164022dcbf6750ef220b7a1133a1183eb upstream.
While debugging a usb3 problem, I stumbled upon this lockdep warning.
Oct 18 21:41:17 dhcp47-74 kernel: =================================
Oct 18 21:41:17 dhcp47-74 kernel: [ INFO: inconsistent lock state ]
Oct 18 21:41:17 dhcp47-74 kernel: 3.1.0-rc4nmi+ #456
Oct 18 21:41:17 dhcp47-74 kernel: ---------------------------------
Oct 18 21:41:17 dhcp47-74 kernel: inconsistent {IN-HARDIRQ-W} -> {HARDIRQ-ON-W} usage.
Oct 18 21:41:17 dhcp47-74 kernel: swapper/0 [HC0[0]:SC1[1]:HE1:SE0] takes:
Oct 18 21:41:17 dhcp47-74 kernel: (&(&xhci->lock)->rlock){?.-...}, at: [<ffffffffa0228990>] xhci_stop_endpoint_command_watchdog+0x30/0x340 [xhci_hcd]
Oct 18 21:41:17 dhcp47-74 kernel: {IN-HARDIRQ-W} state was registered at:
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff8109a941>] __lock_acquire+0x781/0x1660
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff8109bed7>] lock_acquire+0x97/0x170
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff81501b46>] _raw_spin_lock+0x46/0x80
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffffa02299fa>] xhci_irq+0x3a/0x1960 [xhci_hcd]
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffffa022b351>] xhci_msi_irq+0x31/0x40 [xhci_hcd]
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff810d2305>] handle_irq_event_percpu+0x85/0x320
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff810d25e8>] handle_irq_event+0x48/0x70
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff810d537d>] handle_edge_irq+0x6d/0x130
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff810048c9>] handle_irq+0x49/0xa0
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff8150d56d>] do_IRQ+0x5d/0xe0
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff815029b0>] ret_from_intr+0x0/0x13
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff81388aca>] usb_set_device_state+0x8a/0x180
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff8138f038>] usb_add_hcd+0x2b8/0x730
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffffa022ed7e>] xhci_pci_probe+0x9e/0xd4 [xhci_hcd]
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff8127915f>] local_pci_probe+0x5f/0xd0
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff8127a569>] pci_device_probe+0x119/0x120
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff81334473>] driver_probe_device+0xa3/0x2c0
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff8133473b>] __driver_attach+0xab/0xb0
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff8133373c>] bus_for_each_dev+0x6c/0xa0
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff813341fe>] driver_attach+0x1e/0x20
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff81333b88>] bus_add_driver+0x1f8/0x2b0
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff81334df6>] driver_register+0x76/0x140
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff8127a7c6>] __pci_register_driver+0x66/0xe0
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffffa013c04a>] snd_timer_find+0x4a/0x70 [snd_timer]
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffffa013c00e>] snd_timer_find+0xe/0x70 [snd_timer]
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff810001d3>] do_one_initcall+0x43/0x180
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff810a9ed2>] sys_init_module+0x92/0x1f0
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff8150ab6b>] system_call_fastpath+0x16/0x1b
Oct 18 21:41:17 dhcp47-74 kernel: irq event stamp: 631984
Oct 18 21:41:17 dhcp47-74 kernel: hardirqs last enabled at (631984): [<ffffffff81502720>] _raw_spin_unlock_irq+0x30/0x50
Oct 18 21:41:17 dhcp47-74 kernel: hardirqs last disabled at (631983): [<ffffffff81501c49>] _raw_spin_lock_irq+0x19/0x90
Oct 18 21:41:17 dhcp47-74 kernel: softirqs last enabled at (631980): [<ffffffff8105ff63>] _local_bh_enable+0x13/0x20
Oct 18 21:41:17 dhcp47-74 kernel: softirqs last disabled at (631981): [<ffffffff8150ce6c>] call_softirq+0x1c/0x30
Oct 18 21:41:17 dhcp47-74 kernel:
Oct 18 21:41:17 dhcp47-74 kernel: other info that might help us debug this:
Oct 18 21:41:17 dhcp47-74 kernel: Possible unsafe locking scenario:
Oct 18 21:41:17 dhcp47-74 kernel:
Oct 18 21:41:17 dhcp47-74 kernel: CPU0
Oct 18 21:41:17 dhcp47-74 kernel: ----
Oct 18 21:41:17 dhcp47-74 kernel: lock(&(&xhci->lock)->rlock);
Oct 18 21:41:17 dhcp47-74 kernel: <Interrupt>
Oct 18 21:41:17 dhcp47-74 kernel: lock(&(&xhci->lock)->rlock);
Oct 18 21:41:17 dhcp47-74 kernel:
Oct 18 21:41:17 dhcp47-74 kernel: *** DEADLOCK ***
Oct 18 21:41:17 dhcp47-74 kernel:
Oct 18 21:41:17 dhcp47-74 kernel: 1 lock held by swapper/0:
Oct 18 21:41:17 dhcp47-74 kernel: #0: (&ep->stop_cmd_timer){+.-...}, at: [<ffffffff8106abf2>] run_timer_softirq+0x162/0x570
Oct 18 21:41:17 dhcp47-74 kernel:
Oct 18 21:41:17 dhcp47-74 kernel: stack backtrace:
Oct 18 21:41:17 dhcp47-74 kernel: Pid: 0, comm: swapper Tainted: G W 3.1.0-rc4nmi+ #456
Oct 18 21:41:17 dhcp47-74 kernel: Call Trace:
Oct 18 21:41:17 dhcp47-74 kernel: <IRQ> [<ffffffff81098ed7>] print_usage_bug+0x227/0x270
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff810999c6>] mark_lock+0x346/0x410
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff8109a7de>] __lock_acquire+0x61e/0x1660
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff81099893>] ? mark_lock+0x213/0x410
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff8109bed7>] lock_acquire+0x97/0x170
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffffa0228990>] ? xhci_stop_endpoint_command_watchdog+0x30/0x340 [xhci_hcd]
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff81501b46>] _raw_spin_lock+0x46/0x80
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffffa0228990>] ? xhci_stop_endpoint_command_watchdog+0x30/0x340 [xhci_hcd]
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffffa0228990>] xhci_stop_endpoint_command_watchdog+0x30/0x340 [xhci_hcd]
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff8106abf2>] ? run_timer_softirq+0x162/0x570
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff8106ac9d>] run_timer_softirq+0x20d/0x570
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff8106abf2>] ? run_timer_softirq+0x162/0x570
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffffa0228960>] ? xhci_queue_isoc_tx_prepare+0x8e0/0x8e0 [xhci_hcd]
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff810604d2>] __do_softirq+0xf2/0x3f0
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff81020edd>] ? lapic_next_event+0x1d/0x30
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff81090d4e>] ? clockevents_program_event+0x5e/0x90
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff8150ce6c>] call_softirq+0x1c/0x30
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff8100484d>] do_softirq+0x8d/0xc0
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff8105ff35>] irq_exit+0xe5/0x100
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff8150d65e>] smp_apic_timer_interrupt+0x6e/0x99
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff8150b6f0>] apic_timer_interrupt+0x70/0x80
Oct 18 21:41:17 dhcp47-74 kernel: <EOI> [<ffffffff81095d8d>] ? trace_hardirqs_off+0xd/0x10
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff812ddb76>] ? acpi_idle_enter_bm+0x227/0x25b
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff812ddb71>] ? acpi_idle_enter_bm+0x222/0x25b
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff813eda63>] cpuidle_idle_call+0x103/0x290
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff81002155>] cpu_idle+0xe5/0x160
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff814e7f50>] rest_init+0xe0/0xf0
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff814e7e70>] ? csum_partial_copy_generic+0x170/0x170
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff81df8e23>] start_kernel+0x3fc/0x407
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff81df8321>] x86_64_start_reservations+0x131/0x135
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff81df8412>] x86_64_start_kernel+0xed/0xf4
Oct 18 21:41:17 dhcp47-74 kernel: xhci_hcd 0000:00:14.0: xHCI host not responding to stop endpoint command.
Oct 18 21:41:17 dhcp47-74 kernel: xhci_hcd 0000:00:14.0: Assuming host is dying, halting host.
Oct 18 21:41:17 dhcp47-74 kernel: xhci_hcd 0000:00:14.0: HC died; cleaning up
Oct 18 21:41:17 dhcp47-74 kernel: usb 3-4: device descriptor read/8, error -110
Oct 18 21:41:17 dhcp47-74 kernel: usb 3-4: device descriptor read/8, error -22
Oct 18 21:41:17 dhcp47-74 kernel: hub 3-0:1.0: cannot disable port 4 (err = -19)
Basically what is happening is in xhci_stop_endpoint_command_watchdog()
the xhci->lock is grabbed with just spin_lock. What lockdep deduces is
that if an interrupt occurred while in this function it would deadlock
with xhci_irq because that function also grabs the xhci->lock.
Fixing it is trivial by using spin_lock_irqsave instead.
This should be queued to stable kernels as far back as 2.6.33.
Signed-off-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 79c3dd8150fd5236d95766a9e662e3e932b462c9 upstream.
I noticed on my Panther Point system that I wasn't getting hotplug events
for my usb3.0 disk on a usb3 port. I tracked it down to the fact that the
system had the warm reset change bit still set. This seemed to block future
events from being received, including a hotplug event.
Clearing this bit during initialization allowed the hotplug event to be
received and the disk to be recognized correctly.
This patch should be backported to kernels as old as 2.6.39.
Signed-off-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit d31c285b3a71cf9056e6a060de41f37780b0af86 upstream.
Matt's AsMedia xHCI host controller was responding with a Context Error
to an address device command after a configured device reset. Some
sequence of events leads both the slot and endpoint zero add flags
cleared to zero, which the AsMedia host doesn't like:
[ 223.701839] xhci_hcd 0000:03:00.0: Slot ID 1 Input Context:
[ 223.701841] xhci_hcd 0000:03:00.0: @ffff880137b25000 (virt) @ffffc000 (dma) 0x000000 - drop flags
[ 223.701843] xhci_hcd 0000:03:00.0: @ffff880137b25004 (virt) @ffffc004 (dma) 0x000000 - add flags
[ 223.701846] xhci_hcd 0000:03:00.0: @ffff880137b25008 (virt) @ffffc008 (dma) 0x000000 - rsvd2[0]
[ 223.701848] xhci_hcd 0000:03:00.0: @ffff880137b2500c (virt) @ffffc00c (dma) 0x000000 - rsvd2[1]
[ 223.701850] xhci_hcd 0000:03:00.0: @ffff880137b25010 (virt) @ffffc010 (dma) 0x000000 - rsvd2[2]
[ 223.701852] xhci_hcd 0000:03:00.0: @ffff880137b25014 (virt) @ffffc014 (dma) 0x000000 - rsvd2[3]
[ 223.701854] xhci_hcd 0000:03:00.0: @ffff880137b25018 (virt) @ffffc018 (dma) 0x000000 - rsvd2[4]
[ 223.701857] xhci_hcd 0000:03:00.0: @ffff880137b2501c (virt) @ffffc01c (dma) 0x000000 - rsvd2[5]
[ 223.701858] xhci_hcd 0000:03:00.0: Slot Context:
[ 223.701860] xhci_hcd 0000:03:00.0: @ffff880137b25020 (virt) @ffffc020 (dma) 0x8400000 - dev_info
[ 223.701862] xhci_hcd 0000:03:00.0: @ffff880137b25024 (virt) @ffffc024 (dma) 0x010000 - dev_info2
[ 223.701864] xhci_hcd 0000:03:00.0: @ffff880137b25028 (virt) @ffffc028 (dma) 0x000000 - tt_info
[ 223.701866] xhci_hcd 0000:03:00.0: @ffff880137b2502c (virt) @ffffc02c (dma) 0x000000 - dev_state
[ 223.701869] xhci_hcd 0000:03:00.0: @ffff880137b25030 (virt) @ffffc030 (dma) 0x000000 - rsvd[0]
[ 223.701871] xhci_hcd 0000:03:00.0: @ffff880137b25034 (virt) @ffffc034 (dma) 0x000000 - rsvd[1]
[ 223.701873] xhci_hcd 0000:03:00.0: @ffff880137b25038 (virt) @ffffc038 (dma) 0x000000 - rsvd[2]
[ 223.701875] xhci_hcd 0000:03:00.0: @ffff880137b2503c (virt) @ffffc03c (dma) 0x000000 - rsvd[3]
[ 223.701877] xhci_hcd 0000:03:00.0: Endpoint 00 Context:
[ 223.701879] xhci_hcd 0000:03:00.0: @ffff880137b25040 (virt) @ffffc040 (dma) 0x000000 - ep_info
[ 223.701881] xhci_hcd 0000:03:00.0: @ffff880137b25044 (virt) @ffffc044 (dma) 0x2000026 - ep_info2
[ 223.701883] xhci_hcd 0000:03:00.0: @ffff880137b25048 (virt) @ffffc048 (dma) 0xffffe8e0 - deq
[ 223.701885] xhci_hcd 0000:03:00.0: @ffff880137b25050 (virt) @ffffc050 (dma) 0x000000 - tx_info
[ 223.701887] xhci_hcd 0000:03:00.0: @ffff880137b25054 (virt) @ffffc054 (dma) 0x000000 - rsvd[0]
[ 223.701889] xhci_hcd 0000:03:00.0: @ffff880137b25058 (virt) @ffffc058 (dma) 0x000000 - rsvd[1]
[ 223.701892] xhci_hcd 0000:03:00.0: @ffff880137b2505c (virt) @ffffc05c (dma) 0x000000 - rsvd[2]
...
[ 223.701927] xhci_hcd 0000:03:00.0: // Ding dong!
[ 223.701992] xhci_hcd 0000:03:00.0: Setup ERROR: address device command for slot 1.
The xHCI spec says that both flags must be set to one for the Address
Device command. When the device is first enumerated,
xhci_setup_addressable_virt_dev() does set those flags. However, when
the device is addressed after it has been reset in the configured state,
xhci_setup_addressa |
