| Age | Commit message (Collapse) | Author |
|---|
|
Conflicts:
kernel/irq/chip.c
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6: (50 commits)
pcmcia: rework the irq_req_t typedef
pcmcia: remove deprecated handle_to_dev() macro
pcmcia: pcmcia_request_window() doesn't need a pointer to a pointer
pcmcia: remove unused "window_t" typedef
pcmcia: move some window-related code to pcmcia_ioctl.c
pcmcia: Change window_handle_t logic to unsigned long
pcmcia: Pass struct pcmcia_socket to pcmcia_get_mem_page()
pcmcia: Pass struct pcmcia_device to pcmcia_map_mem_page()
pcmcia: Pass struct pcmcia_device to pcmcia_release_window()
drivers/pcmcia: remove unnecessary kzalloc
pcmcia: correct handling for Zoomed Video registers in topic.h
pcmcia: fix printk formats
pcmcia: autoload module pcmcia
pcmcia/staging: update comedi drivers
PCMCIA: stop duplicating pci_irq in soc_pcmcia_socket
PCMCIA: ss: allow PCI IRQs > 255
PCMCIA: soc_common: remove 'dev' member from soc_pcmcia_socket
PCMCIA: soc_common: constify soc_pcmcia_socket ops member
PCMCIA: sa1111: remove duplicated initializers
PCMCIA: sa1111: wrap soc_pcmcia_socket to contain sa1111 specific data
...
|
|
That is "success", "unknown", "through", "performance", "[re|un]mapping"
, "access", "default", "reasonable", "[con]currently", "temperature"
, "channel", "[un]used", "application", "example","hierarchy", "therefore"
, "[over|under]flow", "contiguous", "threshold", "enough" and others.
Signed-off-by: André Goddard Rosa <andre.goddard@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The correct word is handshake.
Signed-off-by: Ozan Çağlayan <ozan@pardus.org.tr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This patch adds the vendor and device id for the Mobilcom Debitel UMTS surf
stick (a.k.a. 4G Systems XSStick W14, MobiData MBD-200HU, ...).
To see these ids, you need to switch the stick to modem operation first
with the help of usb_modeswitch. This makes it switch from 1c9e:f000 to
1c9e:9603 and thus be recognized by the option driver.
Signed-off-by: Gernot Hillier <gernot@hillier.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
a quirky chipset needs periodic schedules to run for a minimum
time before they can be disabled again. This enforces the requirement
with a time stamp and a calculated delay
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
On tx channel abort a cppi interrupt is generated for a short time by
setting the lowest bit of the TCPPICOMPPTR register. It is then reset
immediately by clearing the bit. When the interrupt handler is run,
it does not detect an interrupt in the TCPPIMSKSR or RCPPIMSKSR
registers and thus exits early without writing the TCPPIEOIR register.
It appears that this inhibits further cppi interrupts until the handler
is called by chance, f.ex. from davinci_interrupt().
By moving the unmasking of the interrupt below the writes to
TCPPICOMPPTR, no interrupt is generated and no write to TCPPIEOIR is
necessary.
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
In gadget mode the answer to a control request should be followed by
a zero-length packet if the amount transferred is an exact multiple of
the endpoint's packet size and the requests has its "zero" flag set.
This patch prevents the request from being immediately removed from the
queue when a control IN transfer ends on a full packet and "zero" is set.
The next time ep0_txstate is entered, a zero-length packet is queued and
the request is removed as fifo_count is 0.
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Isochronous Tx DMA is getting programmed but never getting started
for CPPI and TUSB DMAs and thus Isochronous Tx doesn't work.
Fixing it by starting DMAs using musb_h_tx_dma_start().
Signed-off-by: Swaminathan S <swami.iyer@ti.com>
Signed-off-by: Babu Ravi <ravibabu@ti.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Removes below unnecessary log of almost 28 lines during boot.
musb_hdrc: hw_ep 0shared, max 64
musb_hdrc: hw_ep 1tx, max 512
musb_hdrc: hw_ep 1rx, max 512
...
...
musb_hdrc: hw_ep 13shared, max 4096
musb_hdrc: hw_ep 14shared, max 1024
musb_hdrc: hw_ep 15shared, max 1024
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
- fixed shared interrupt bug reported by Vadim Lobanov
- fixed possible warning oops on driver unload when connected
- prevent interrupt flood in PIO mode ("modprobe amd5536udc use_dma=0")
when using gadget ether
Signed-off-by: Thomas Dahlmann <dahlmann.thomas@arcor.de>
Cc: Robert Richter <robert.richter@amd.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The use of urb->actual_length to update tx_outstanding_bytes
implicitly assumes that the number of bytes actually written is the
same as the number of bytes we tried to write. On error that
assumption is violated so just use transfer_buffer_length the number
of bytes we intended to write to the device.
If an error occurs we need to fall through and call
usb_serial_port_softint to wake up processes waiting in
tty_wait_until_sent.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The driver incorrectly cancels the mass-storage device CSW request
(which leads to device reset) due to giving back URB at the head of
endpoint's queue after sending each STALL handshake; stop doing that
and start checking for the queue being non-empty before stalling an
endpoint and disallowing stall in such case in musb_gadget_set_halt()
like the other gadget drivers do.
Moreover, the driver starts Rx request despite of the endpoint being
halted -- fix this by moving the SendStall bit check from musb_g_rx()
to rxstate(). And we also sometimes get into rxstate() with DMA still
active after clearing an endpoint's halt (not clear why), so bail out
in this case, similarly to what txstate() does...
While at it, also do the following changes :
- in musb_gadget_set_halt(), remove pointless Tx FIFO flushing (the
driver does not allow stalling with non-empty Tx FIFO anyway);
- in rxstate(), stop pointlessly zeroing the 'csr' variable;
- in musb_gadget_set_halt(), move the 'done' label to a more proper
place;
- in musb_g_rx(), eliminate the 'done' label completely...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1304) fixes a regression in ehci-hcd. Evidently some
hubs don't handle Clear-TT-Buffer requests correctly, so we should
avoid sending them when they don't appear to be absolutely necessary.
The reported symptom is that output on a downstream audio device cuts
out because the hub stops relaying isochronous packets.
The patch prevents Clear-TT-Buffer requests from being sent following
a STALL handshake. In theory a STALL indicates either that the
downstream device sent a STALL or that no matching TT buffer could be
found. In either case, the transfer is completed and the TT buffer
does not remain busy, so it doesn't need to be cleared.
Also, the patch fixes a minor flaw in the code that actually sends the
Clear-TT-Buffer requests. Although the pipe direction isn't really
used for control transfers, it should be a Send rather than a Receive.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Javier Kohen <jkohen@users.sourceforge.net>
CC: David Brownell <david-b@pacbell.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Most of the irq_req_t typedef'd struct can be re-worked quite
easily:
(1) IRQInfo2 was unused in any case, so drop it.
(2) IRQInfo1 was used write-only, so drop it.
(3) Instance (private data to be passed to the IRQ handler):
Most PCMCIA drivers using pcmcia_request_irq() to actually
register an IRQ handler set the "dev_id" to the same pointer
as the "priv" pointer in struct pcmcia_device. Modify the two
exceptions (ipwireless, ibmtr_cs) to also work this waym and
set the IRQ handler's "dev_id" to p_dev->priv unconditionally.
(4) Handler is to be of type irq_handler_t.
(5) Handler != NULL already tells whether an IRQ handler is present.
Therefore, we do not need the IRQ_HANDLER_PRESENT flag in
irq_req_t.Attributes.
CC: netdev@vger.kernel.org
CC: linux-bluetooth@vger.kernel.org
CC: linux-ide@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: linux-scsi@vger.kernel.org
CC: alsa-devel@alsa-project.org
CC: Jaroslav Kysela <perex@perex.cz>
CC: Jiri Kosina <jkosina@suse.cz>
CC: Karsten Keil <isdn@linux-pingi.de>
for the Bluetooth parts: Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
Update remaining users and remove deprecated handle_to_dev() macro
CC: Harald Welte <laforge@gnumonks.org>
CC: netdev@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: linux-serial@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: option.c: add support for D-Link DWM-162-U5
USB: usbmon: fix bug in mon_buff_area_shrink
USB: xhci: Fix scratchpad deallocation.
USB: xhci: Fix TRB physical to virtual address translation.
USB: xhci: Fix bug memory free after failed initialization.
USB: cdc_acm: Fix memory leak after hangup
USB: cdc_acm: Fix race condition when opening tty
USB: ohci: quirk AMD prefetch for USB 1.1 ISO transfer
|
|
Add D-Link DWM-162-U5 device id 1e0e:ce16 into option driver. The device
has 4 interfaces, of which 1 is handled by storage and the other 3 by
option driver.
The device appears first as CD-only 05c6:2100 device and must be
switched to 1e0e:ce16 mode either by using "eject CD" or usb_modeswitch.
The MessageContent for usb_modeswitch.conf is:
"55534243e0c26a85000000000000061b000000020000000000000000000000"
Signed-off-by: Zhang Le <r0bertz@gentoo.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1299b) fixes a bug in an error-handling path of usbmon's
binary interface. The storage area for URB data is divided into
fixed-size blocks. If an URB's data can't be copied, the area
reserved for it should be decreased to the size of the truncated
information (rounded up to a block boundary). Rounding up the amount
to be removed and subtracting it from the reserved size is definitely
the wrong thing to do.
Also, when the data for an isochronous URB can't be copied, we can
still copy the isoc packet descriptors. In fact the current code does
copy the descriptors, but then sets the capture length to 0 so they
remain inaccessible. The capture length should be reduced to the
length of the descriptors, not set to 0.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Pete Zaitcev <zaitcev@redhat.com>
CC: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The scratchpad_free() function uses xhci->page_size to free some memory
with pci_free_consistent(). However, the page_size is set to zero before
the call, causing kernel oopses on driver unload. Call scratchpad_free()
before setting xhci->page_size to zero.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: John Youn <John.Youn@synopsys.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The trb_in_td() function in the xHCI driver is supposed to translate a
physical transfer buffer request (TRB) into a virtual pointer to the ring
segment that TRB is in.
Unfortunately, a mistake in this function may cause endless loops as the
driver searches through the linked list of ring segments over and over
again. Fix a couple bugs that may lead to loops or bad output:
1. Bail out if we get a NULL pointer when translating the segment's
private structure and the starting DMA address of the segment chunk. If
this happens, we've been handed a starting TRB pointer from a different
ring.
2. Make sure the function works when there's multiple segments in the
ring. In the while loop to search through the ring segments, use the
current segment variable (cur_seg), rather than the starting segment
variable (start_seg) that is passed in.
3. Stop searching the ring if we've run through all the segments in the
ring.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
If the xHCI driver fails during the memory initialization, xhci->ir_set
may not be a valid pointer. Check that it points to valid DMA'able memory
before writing to that address during the memory freeing process.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Am Donnerstag, 10. September 2009 15:43:53 schrieb Dietmar Hilbrich:
> Hello,
>
> i have the following problem with the cdc-acm - driver:
>
> I'm using the driver with an "Ericsson F3507G" on a Thinkpad T400.
>
> If a disable the device (with the RFKill-Switch) while it is used by a
> programm like ppp, the driver doesn't seem to correctly clean up the tty,
> even after the program has been closed)
>
> The tty is still active (e.g. there still exists an entry in
> /sys/dev/char/166:0 if ttyACM0 was used) and if a reacticate the device,
> this device entry will be skipped and the Device-Nodes ttyACM1, ttyACM2
> and ttyACM3 will be used.
>
> This problem was introduced with the commit
> 10077d4a6674f535abdbe25cdecb1202af7948f1 (before 2.6.31-rc1) and still
> exists in 2.6.31.
>
> I was able the fix this problem with the following patch:
>
> diff --git a/drivers/usb/class/cdc-acm.c b/drivers/usb/class/cdc-acm.c
> index 2bfc41e..0970d2f 100644
> --- a/drivers/usb/class/cdc-acm.c
> +++ b/drivers/usb/class/cdc-acm.c
> @@ -676,6 +676,7 @@ static void acm_tty_hangup(struct tty_struct *tty)
> struct acm *acm = tty->driver_data;
> tty_port_hangup(&acm->port);
> acm_port_down(acm, 0);
> + acm_tty_unregister(acm);
> }
I have the same problem with cdc-acm (I'm using a Samsung SGH-U900): when I
unplug it from the USB port during a PPP connection, the ppp daemon gets the
hangup correctly (and closes the device), but the struct acm corresponding to
the device disconnected is not freed. Hence reconnecting the device results in
creation of /dev/ttyACM(x+1). The same happens when the system is hibernated
during a PPP connection.
This memory leak is due to the fact that when the tty is hung up,
tty_port_close_start() returns always zero, and acm_tty_close() never reaches
the point where acm_tty_unregister() is called.
Here is a fix for this.
Signed-off-by: Francesco Lavra <francescolavra@interfree.it>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
If acm_rx_tasklet() gets called before tty_port_block_til_ready()
returns, then bulk IN urbs may not be sent. This fixes it.
Signed-off-by: Henry Gebhardt <gebhardt@astro.uni-tuebingen.de>
Acked-by: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The following patch in the driver is required to avoid USB 1.1 device
failures that may occur due to requests from USB OHCI controllers may
be overwritten if the latency for any pending request by the USB
controller is very long (in the range of milliseconds).
Signed-off-by: Libin Yang <libin.yang@amd.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Original discussion:
http://thread.gmane.org/gmane.linux.usb.general/23217/focus=23248
or
http://marc.info/?l=linux-usb&m=125553790714133&w=2
9a68e39d4a701fb3be03cae9b462408664ebd205 broke carrier handling so that a
cp210x setup which needed the carrier lines set up (non CLOCAL) which did
not make a call which set the termios bits left the lines down even if
CLOCAL was not asserted.
Fix this not by reverting but by adding the proper dtr_rts and
carrier_raised methods. This both sets the modem lines properly and also
implements the correct blocking semantics for the port as required by
POSIX.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Reported-by: Karl Hiramoto <karl@hiramoto.org>
Tested-by: Karl Hiramoto <karl@hiramoto.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Convert PCMCIA drivers to use the dynamic debug infrastructure, instead of
requiring manual settings of PCMCIA_DEBUG.
Also, remove all usages of the CS_CHECK macro and replace them with proper
Linux style calling and return value checking. The extra error reporting may
be dropped, as the PCMCIA core already complains about any (non-driver-author)
errors.
CC: linux-mtd@lists.infradead.org
CC: linux-usb@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
fsl_udc_release() calls dma_free_coherent() with an inappropriate
device passed to it, and since the device has no dma_ops, the following
oops pops up:
Kernel BUG at d103ce9c [verbose debug info unavailable]
Oops: Exception in kernel mode, sig: 5 [#1]
...
NIP [d103ce9c] fsl_udc_release+0x50/0x80 [fsl_usb2_udc]
LR [d103ce74] fsl_udc_release+0x28/0x80 [fsl_usb2_udc]
Call Trace:
[cfbc7dc0] [d103ce74] fsl_udc_release+0x28/0x80 [fsl_usb2_udc]
[cfbc7dd0] [c01a35c4] device_release+0x2c/0x90
[cfbc7de0] [c016b480] kobject_cleanup+0x58/0x98
[cfbc7e00] [c016c52c] kref_put+0x54/0x6c
[cfbc7e10] [c016b360] kobject_put+0x34/0x64
[cfbc7e20] [c01a1d0c] put_device+0x1c/0x2c
[cfbc7e30] [d103dbfc] fsl_udc_remove+0xc0/0x1e4 [fsl_usb2_udc]
...
This patch fixes the issue by passing dev->parent, which points to
a correct device.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Li Yang <leoli@freescale.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Add ID for Tlaytech TUE800 CDMA modem to the option driver.
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Acked-By: Matthias Urlichs <matthias@urlichs.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch presents fixes for the autosuspend feature implementation in
sierra usb serial driver in functions sierra_open(), sierra_close() and
stop_read_write_urbs().
The patch "sierra_close() must resume the device before it notifies it
of a closure" submitted by Oliver Neukum on Wed, October 14 has been
merged as fix in sierra_close() function.
The bug fix in sierra_open() function restores the autopm interface
state on error condition.
The bug fix in in stop_read_write_urbs() function assures that both
receive and interrupt urbs are recycled.
Signed-off-by: Elina Pasheva <epasheva@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch presents a fix for the autosuspend feature implementation in
sierra usb serial driver for function sierra_send_setup(). Because it
is possible to call sierra_send_setup() before sierra_open() or after
sierra_close() we added a get/put interface activity to assure that the
usb control can happen even when the device is autosuspended.
Signed-off-by: Elina Pasheva <epasheva@sierrawireless.com>
Tested-by: Matthew Safar <msafar@sierrawireless.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
drivers/built-in.o: In function `pxa25x_udc_probe':
drivers/usb/gadget/pxa25x_udc.c:2195: undefined reference to `otg_get_transceiver'
drivers/usb/gadget/pxa25x_udc.c:2300: undefined reference to `otg_put_transceiver'
pxa25x_udc.c unconditionally uses these two functions, so we need to
ensure that the object providing them is also built.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Remove expository comments and fix USB VID and PID
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
usb-storage: Workaround devices with bogus sense size
Some devices, such as Huawei E169, advertise more than the standard
amount of sense data, causing us to set US_FL_SANE_SENSE, assuming
they support it. However, they subsequently fail the request sense
with that size.
This works around it generically. When a sense request fails due to
a device returning an error, US_FL_SANE_SENSE was set, and that sense
request used a larger sense size, we retry with a smaller size before
giving up.
Based on an original patch by Ben Efros <ben@pc-doctor.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
When the EHCI driver falls behind in its scheduling, the active stream's
first empty microframe may be in the past with respect to the current
microframe. The code attempts to move the starting microframe ("start") N
number of microframes forward, where N is the interval of endpoint.
However, stream->interval is a copy of the endpoint's bInterval, which is
designated in frames for FS devices, and microframes for HS devices.
Convert stream->interval to microframes before using it to move the
starting microframe forward.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Here is a patch for Airplus MCD 650 card
Note: This device is with Victor V Kudlak, and he confirmed that this
device works with the patch.
Signed-off-by: Huzaifa Sidhpurwala <sidhpurwala.huzaifa@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
A halted qTD always triggers a hardware list update because the qset was
either removed or reactivated.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
If an endpoint is deleted before it's been fully added to the hardware
list, the associated qset will not be fully initialized and an oops will
occur when complete(&qset->remove_complete) is called. This can happen
if a queued URB is cancelled.
Fix this by only removing the qset from the hardware list if the
cancelled URB had qTDs.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
An urb's transfer buffer must be kmalloc'd memory and not point to the
stack or a DMA API warning results.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The MUSB code relies on platform implementations that currently only
exists for Arm and Blackfin processors, so have the MUSB Kconfig depend
upon those arches.
This should prevent other arches from building MUSB via randconfig.
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This reverts commit db8be50c4307dac2b37305fc59c8dc0f978d09ea, as per
http://bugzilla.kernel.org/show_bug.cgi?id=14374
http://marc.info/?l=linux-kernel&m=125446885705223&w=4
We simply can't do the USB handoff at FIXUP_HEADER time, since it will
often require us to have valid IO mappings etc. But that in turn
requires a whole different approach, not this trivial one-liner.
Maybe we could teach all the USB quirk handoff handlers to only do the
quirk if the device has all its registers set up (since if it isn't
initialized, it's unlikely to be active), but regardless that will need
a whole lot more code than just saying "let's do it really early".
The proper fix is almost certainly to just leave the legacy IOMMU
mappings active until after all devices have been initialized.
Reported-by: Nick Piggin <npiggin@suse.de>
Cc: David Woodhouse <David.Woodhouse@intel.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (32 commits)
USB: serial: no unnecessary GFP_ATOMIC in oti6858
USB: serial: fix race between unthrottle and completion handler in visor
USB: serial: fix assumption that throttle/unthrottle cannot sleep
USB: serial: fix race between unthrottle and completion handler in symbolserial
USB: serial: fix race between unthrottle and completion handler in opticon
USB: ehci: Fix isoc scheduling boundary checking.
USB: storage: When a device returns no sense data, call it a Hardware Error
USB: small fix in error case of suspend in generic usbserial code
USB: visor: fix trivial accounting bug in visor driver
USB: Fix throttling in generic usbserial driver
USB: cp210x: Add support for the DW700 UART
USB: ipaq: fix oops when device is plugged in
USB: isp1362: fix build warnings on 64-bit systems
USB: gadget: imx_udc: Use resource size
USB: storage: iRiver P7 UNUSUAL_DEV patch
USB: musb: make HAVE_CLK support optional
USB: xhci: Fix dropping endpoints from the xHC schedule.
USB: xhci: Don't wait for a disable slot cmd when HC dies.
USB: xhci: Handle canceled URBs when HC dies.
USB: xhci: Stop debugging polling loop when HC dies.
...
|
|
GFP_ATOMIC without good cause is evil.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
usb:usbserial:visor: fix race between unthrottle and completion handler
visor_unthrottle() mustn't resubmit the URB unconditionally
as the URB may still be running.
the same bug as opticon.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
many serial subdrivers are clearly written as if throttle/unthrottle
cannot sleep. This leads to unneeded atomic submissions. This
patch converts affected drivers in a way to makes very clear that
throttle/unthrottle can sleep. Thus future misdesigns can be avoided
and efficiency and reliability improved.
This removes any such assumption using GFP_KERNEL and spin_lock_irq()
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
usb:usbserial:symbolserial: fix race between unthrottle and completion handler
symbol_unthrottle() mustn't resubmit the URB unconditionally
as the URB may still be running.
the same bug as opticon.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
usb:usbserial:opticon: fix race between unthrottle and completion handler
opticon_unthrottle() mustn't resubmit the URB unconditionally
as the URB may still be running.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The EHCI driver does some bounds checking when it's scheduling an iTD for
an active endpoint. It sets the local variable start to
stream->next_uframe and moves that variable further in the schedule if
necessary. However, the driver fails to do anything with start before
jumping to the ready label and setting the URB's starting frame to
stream->next_uframe. Alan Stern confirms the EHCI driver should set
stream->next_uframe to start before jumping.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1294) fixes a problem that has plagued users for several
kernel releases. Some USB mass-storage devices don't return any sense
data when they encounter certain kinds of errors. The SCSI layer
interprets this to mean that the operation should be retried, and the
same thing happens -- over and over again with no limit. In some
circumstances (such as when a bus reset occurs) that is the right
thing to do, but not here.
The patch checks for this condition (a transport failure with no sense
data) and changes the result code to DID_ERROR and the sense code to
Hardware Error. This does get only a limited number of retries, and
so the command will fail relatively quickly instead of getting stuck
in an infinite loop.
This fixes a large part of Bugzilla #14118.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Mantas Mikulenas <grawity@gmail.com>
CC: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
