| Age | Commit message (Collapse) | Author |
|---|
|
commit 7d1d865181185bdf1316d236b1b4bd02c9020729 upstream.
Normalize phy->attached_sas_addr to return a zero-address in the case
when device-type == NO_DEVICE or the linkrate is invalid to handle
expanders that put non-zero sas addresses in the discovery response:
sas: ex 5001b4da000f903f phy02:U:0 attached: 0100000000000000 (no device)
sas: ex 5001b4da000f903f phy01:U:0 attached: 0100000000000000 (no device)
sas: ex 5001b4da000f903f phy03:U:0 attached: 0100000000000000 (no device)
sas: ex 5001b4da000f903f phy00:U:0 attached: 0100000000000000 (no device)
Reported-by: Andrzej Jakowski <andrzej.jakowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 1699490db339e2c6b3037ea8e7dcd6b2755b688e upstream.
If an expander reports 'PHY VACANT' for a phy index prior to the one
that generated a BCN libsas fails rediscovery. Since a vacant phy is
defined as a valid phy index that will never have an attached device
just continue the search.
Signed-off-by: Thomas Jackson <thomas.p.jackson@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 41f8ad76362e7aefe3a03949c43e23102dae6e0b upstream.
It used to be that minors where 8 bit. But now they
are actually 20 bit. So the fix is simplicity itself.
I've tested with 300 devices and all user-mode utils
work just fine. I have also mechanically added 10,000
to the ida (so devices are /dev/osd10000, /dev/osd10001 ...)
and was able to mkfs an exofs filesystem and access osds
from user-mode.
All the open-osd user-mode code uses the same library
to access devices through their symbolic names in
/dev/osdX so I'd say it's pretty safe. (Well tested)
This patch is very important because some of the systems
that will be deploying the 3.2 pnfs-objects code are larger
than 64 OSDs and will stop to work properly when reaching
that number.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fea6d607e154cf96ab22254ccb48addfd43d4cb5 upstream.
This patch (as1520) fixes a bug in the SCSI layer's power management
implementation.
LUN scanning can be carried out asynchronously in do_scan_async(), and
sd uses an asynchronous thread for the time-consuming parts of disk
probing in sd_probe_async(). Currently nothing coordinates these
async threads with system sleep transitions; they can and do attempt
to continue scanning/probing SCSI devices even after the host adapter
has been suspended. As one might expect, the outcome is not ideal.
This is what the "prepare" stage of system suspend was created for.
After the prepare callback has been called for a host, target, or
device, drivers are not allowed to register any children underneath
them. Currently the SCSI prepare callback is not implemented; this
patch rectifies that omission.
For SCSI hosts, the prepare routine calls scsi_complete_async_scans()
to wait until async scanning is finished. It might be slightly more
efficient to wait only until the host in question has been scanned,
but there's currently no way to do that. Besides, during a sleep
transition we will ultimately have to wait until all the host scanning
has finished anyway.
For SCSI devices, the prepare routine calls async_synchronize_full()
to wait until sd probing is finished. The routine does nothing for
SCSI targets, because asynchronous target scanning is done only as
part of host scanning.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 267a6ad4aefaafbde607804c60945bcf97f91c1b upstream.
In do_scan_async(), calling scsi_autopm_put_host(shost) may reference
freed shost, and cause Posison overwitten warning.
Yes, this case can happen, for example, an USB is disconnected just
when do_scan_async() thread starts to run, then scsi_host_put() called
in scsi_finish_async_scan() will lead to shost be freed(because the
refcount of shost->shost_gendev decreases to 1 after USB disconnects),
at this point, if references shost again, system will show following
warning msg.
To make scsi_autopm_put_host(shost) always reference a valid shost,
put it just before scsi_host_put() in function
scsi_finish_async_scan().
[ 299.281565] =============================================================================
[ 299.281634] BUG kmalloc-4096 (Tainted: G I ): Poison overwritten
[ 299.281682] -----------------------------------------------------------------------------
[ 299.281684]
[ 299.281752] INFO: 0xffff880056c305d0-0xffff880056c305d0. First byte
0x6a instead of 0x6b
[ 299.281816] INFO: Allocated in scsi_host_alloc+0x4a/0x490 age=1688
cpu=1 pid=2004
[ 299.281870] __slab_alloc+0x617/0x6c1
[ 299.281901] __kmalloc+0x28c/0x2e0
[ 299.281931] scsi_host_alloc+0x4a/0x490
[ 299.281966] usb_stor_probe1+0x5b/0xc40 [usb_storage]
[ 299.282010] storage_probe+0xa4/0xe0 [usb_storage]
[ 299.282062] usb_probe_interface+0x172/0x330 [usbcore]
[ 299.282105] driver_probe_device+0x257/0x3b0
[ 299.282138] __driver_attach+0x103/0x110
[ 299.282171] bus_for_each_dev+0x8e/0xe0
[ 299.282201] driver_attach+0x26/0x30
[ 299.282230] bus_add_driver+0x1c4/0x430
[ 299.282260] driver_register+0xb6/0x230
[ 299.282298] usb_register_driver+0xe5/0x270 [usbcore]
[ 299.282337] 0xffffffffa04ab03d
[ 299.282364] do_one_initcall+0x47/0x230
[ 299.282396] sys_init_module+0xa0f/0x1fe0
[ 299.282429] INFO: Freed in scsi_host_dev_release+0x18a/0x1d0 age=85
cpu=0 pid=2008
[ 299.282482] __slab_free+0x3c/0x2a1
[ 299.282510] kfree+0x296/0x310
[ 299.282536] scsi_host_dev_release+0x18a/0x1d0
[ 299.282574] device_release+0x74/0x100
[ 299.282606] kobject_release+0xc7/0x2a0
[ 299.282637] kobject_put+0x54/0xa0
[ 299.282668] put_device+0x27/0x40
[ 299.282694] scsi_host_put+0x1d/0x30
[ 299.282723] do_scan_async+0x1fc/0x2b0
[ 299.282753] kthread+0xdf/0xf0
[ 299.282782] kernel_thread_helper+0x4/0x10
[ 299.282817] INFO: Slab 0xffffea00015b0c00 objects=7 used=7 fp=0x
(null) flags=0x100000000004080
[ 299.282882] INFO: Object 0xffff880056c30000 @offset=0 fp=0x (null)
[ 299.282884]
...
Signed-off-by: Huajun Li <huajun.li.lee@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2cb6fc8c014b9b00c4487a79b8f6ed0da4121f45 upstream.
Removed redundant calling of _scsih_probe_devices() from _scsih_probe as
it is getting called from _scsih_scan_finished.
Also moved the function scsi_scan_host(shost) to get called after the
volumes on warp drive are reported to the OS. Otherwise by the time
the (ioc->hide_drives) flags is set, the volumes on warp drive
are reported to the OS already.
Also modified the initialization of reply queues only in case of driver load
time in the function _base_make_ioc_operational().
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cced5041ed5a2d1352186510944b0ddfbdbe4c0b upstream.
sym53c8xx_slave_destroy unconditionally assumes that sym53c8xx_slave_alloc has
succesesfully allocated a sym_lcb. This can lead to a NULL pointer dereference
(exposed by commit 4e6c82b).
Signed-off-by: Stratos Psomadakis <psomas@gentoo.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 0bfc96cb77224736dfa35c3c555d37b3646ef35e upstream.
[ Changes with respect to 3.3: return -ENOTTY from scsi_verify_blk_ioctl
and -ENOIOCTLCMD from sd_compat_ioctl. ]
Linux allows executing the SG_IO ioctl on a partition or LVM volume, and
will pass the command to the underlying block device. This is
well-known, but it is also a large security problem when (via Unix
permissions, ACLs, SELinux or a combination thereof) a program or user
needs to be granted access only to part of the disk.
This patch lets partitions forward a small set of harmless ioctls;
others are logged with printk so that we can see which ioctls are
actually sent. In my tests only CDROM_GET_CAPABILITY actually occurred.
Of course it was being sent to a (partition on a) hard disk, so it would
have failed with ENOTTY and the patch isn't changing anything in
practice. Still, I'm treating it specially to avoid spamming the logs.
In principle, this restriction should include programs running with
CAP_SYS_RAWIO. If for example I let a program access /dev/sda2 and
/dev/sdb, it still should not be able to read/write outside the
boundaries of /dev/sda2 independent of the capabilities. However, for
now programs with CAP_SYS_RAWIO will still be allowed to send the
ioctls. Their actions will still be logged.
This patch does not affect the non-libata IDE driver. That driver
however already tests for bd != bd->bd_contains before issuing some
ioctl; it could be restricted further to forbid these ioctls even for
programs running with CAP_SYS_ADMIN/CAP_SYS_RAWIO.
Cc: linux-scsi@vger.kernel.org
Cc: Jens Axboe <axboe@kernel.dk>
Cc: James Bottomley <JBottomley@parallels.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[ Make it also print the command name when warning - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 577ebb374c78314ac4617242f509e2f5e7156649 upstream.
Introduce a wrapper around scsi_cmd_ioctl that takes a block device.
The function will then be enhanced to detect partition block devices
and, in that case, subject the ioctls to whitelisting.
Cc: linux-scsi@vger.kernel.org
Cc: Jens Axboe <axboe@kernel.dk>
Cc: James Bottomley <JBottomley@parallels.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit aff132d95ffe14eca96cab90597cdd010b457af7 upstream.
The amount of memory required for tracking chain buffers is rather
large, and when the host credit count is big, memory allocation
failure occurs inside __get_free_pages.
The fix is to limit the number of chains to 100,000. In addition,
the number of host credits is limited to 30,000 IOs. However this
limitation can be overridden this using the command line option
max_queue_depth. The algorithm for calculating the
reply_post_queue_depth is changed so that it is equal to
(reply_free_queue_depth + 16), previously it was (reply_free_queue_depth * 2).
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 30c43282f3d347f47f9e05199d2b14f56f3f2837 upstream.
Added code to release the spinlock that is used to protect the
raid device list before calling a function that can block. The
blocking was causing a reschedule, and subsequently it is tried
to acquire the same lock, resulting in a panic (NMI Watchdog
detecting a CPU lockup).
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
skb priority
Use DCB notifiers to set the skb priority to allow packets
to be steered and tagged correctly over DCB enabled drivers
that setup traffic classes.
This allows queue_mapping() routines to be removed in these
drivers that were previously inspecting the ethertype of
every skb to mark FCoE/FIP frames.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
During session recovery, the conn_stop call will trigger a flush
to all outstanding SCSI cmds in the xmit queue. This will set
all outstanding task->sc to NULL prior to the session_teardown
call which frees the task memory.
In the bnx2i SCSI response processing path, only the task was being checked
for NULL under the session lock before the task->sc->request dereferencing.
If there are outstanding SCSI cmd responses pending for process, the
following kernel panic can be exposed where task->sc was found to be NULL.
Call Trace:
[ 69.720205] [<ffffffffa040d0d0>] bnx2i_process_new_cqes+0x290/0x3c0 [bnx2i]
[ 69.804289] [<ffffffffa040d233>] bnx2i_fastpath_notification+0x33/0xa0 [bnx2
i]
[ 69.891490] [<ffffffffa040d37b>] bnx2i_indicate_kcqe+0xdb/0x330 [bnx2i]
[ 69.971427] [<ffffffffa03eac5e>] service_kcqes+0x16e/0x1d0 [cnic]
[ 70.045132] [<ffffffffa03eacea>] cnic_service_bnx2x_kcq+0x2a/0x50 [cnic]
[ 70.126105] [<ffffffffa03ead53>] cnic_service_bnx2x_bh+0x43/0x140 [cnic]
[ 70.207081] [<ffffffff81060676>] tasklet_action+0x66/0x110
[ 70.273521] [<ffffffff8106025f>] __do_softirq+0xef/0x220
[ 70.337887] [<ffffffff81447ebc>] call_softirq+0x1c/0x30
This patch adds the !task->sc check and also protects the sc dereferencing
under the session lock.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
iscsi_conn_setup can fail so we must check for NULL being
returned.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
When the qla4xxx_get_fwddb_entry returns QLA_ERROR
the nex_idx is not updated,
for (idx = 0; idx < max_ddbs; idx = next_idx) {
ret = qla4xxx_get_fwddb_entry(ha, idx, NULL, 0, NULL,
&next_idx, &state, &conn_err,
NULL, NULL);
if (ret == QLA_ERROR)
continue;
This means there is a risk that the 'idx < max_ddbs' condition will never
met and the loop will loop forever.
Fix this by explicitly increasing the next_idx in the error condition.
Maybe a break instead of continue is more appropriate, leaving the decision
on the qlogic maintainer.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
With open-iscsi support, target entries persisted in the FLASH were not
login. Added support in the qla4xxx driver to do the login on probe
time to the target entries saved in the FLASH by user.
With this changes upgrade to the new kernel with open-iscsi support in
qla4xxx will ensure users original target entries login on driver load
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
The error exit path leaks preempt count. Add the missing put_cpu().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Yi Zou <yi.zou@intel.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
queue 0.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
[jejb: checkpatch fixes]
Add more fine grain parsing of vha->loop_state to export a more accurate
fc_host port_state.
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
for ISP82xx.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
for ISP82xx.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
ISP82xx firmware hang.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
[jejb: fixup checkpatch error]
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
reset recovery.
We need to return QLA_FUNCTION_TIMEOUT immediately otherwise we mess up the
mailbox command state machine.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
interrupt mode during firmware hang.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
If there is an error creating multiple response queues then we need to revert
the request queue mapping back to request queue 0.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
This function can wait for 5min under certain scenarios. One of them is when
the port is down from switch and bus reset is issued. The bus reset used to
wait for 5 minutes for the loop and upper layer callers used to hang and give
stack trace because of getting stuck for 120 sec. It is legacy code that was
used when the driver used to do queuing of the commands.
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
context
_scsih_smart_predicted_fault is called in an interrupt and therefore
must allocate memory using GFP_ATOMIC.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
The Windows driver .inf disables ASPM on hpsa devices. Do the same because the
selection of a non default ASPM policy can cause the device to hang.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: stable@kernel.org
Acked-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Aacraid controller can hang on some nodes if kernel uses non-default
(powersave) ASPM policy. Controller hangs shortly after successful load and
hardware detection. Scsi error handler detects this hang and tries to restart
hardware but it does not help.
Initially it was noticed on RHEL6-based openVZ kernel after backporting
aacraid driver from mainline (RHEL6 kernel with original driver works well)
http://bugzilla.openvz.org/show_bug.cgi?id=2043
This issue happens because default ASPM policy was changed in Red Hat
kernels. Therefore guys from Red Hat have noticed this problem long time ago:
on Fedora 12
https://bugzilla.redhat.com/show_bug.cgi?id=540478
on Fedora 14
https://bugzilla.redhat.com/show_bug.cgi?id=679385
In RHEL6 kernel this issue was fixed, ASPM was disabled in aacraid driver. In
kernel changelog I've found that seems it was done by Matthew Garrett: -
[scsi] aacraid: Disable ASPM by default (Matthew Garrett) [599735]
However seems this patch was not submitted to mainline. I've reproduced this
issue on vanilla 3.1.0 kernel booted with "pcie_aspm.policy=powersave" option,
So I believe it makes sense to do it now.
Signed-off-by: Vasily Averin <vvs@sw.ru>
[mjg: Checking the Windows drivers indicates that they disable ASPM under all
circumstances, so:]
Acked-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Achim Leubner <Achim_Leubner@pmc-sierra.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
There was supposed to be a kzalloc() here and the compiler complained
about it.
mpt2sas_scsih.c: In function ‘mpt2sas_scsih_reset_handler’:
mpt2sas_scsih.c:2807:21: warning: ‘fw_event’ may be used uninitialized in this function [-Wuninitialized]
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: "Nandigama, Nagalakshmi" <Nagalakshmi.Nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
When we tear down a device we try to flush all outstanding
commands in scsi_free_queue(). However the check in
scsi_request_fn() is imperfect as it only signals that
we _might start_ aborting commands, not that we've actually
aborted some.
So move the printk inside the scsi_kill_request function,
this will also give us a hint about which commands are aborted.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
On Mon, 2011-11-07 at 17:24 +1100, Stephen Rothwell wrote:
> Hi all,
>
> Starting some time last week I am getting the following during boot on
> our PPC970 blade:
>
> calling .ipr_init+0x0/0x68 @ 1
> ipr: IBM Power RAID SCSI Device Driver version: 2.5.2 (April 27, 2011)
> ipr 0000:01:01.0: Found IOA with IRQ: 26
> ipr 0000:01:01.0: Starting IOA initialization sequence.
> ipr 0000:01:01.0: Adapter firmware version: 06160039
> ipr 0000:01:01.0: IOA initialized.
> scsi0 : IBM 572E Storage Adapter
> ------------[ cut here ]------------
> WARNING: at drivers/scsi/scsi_lib.c:1704
> Modules linked in:
> NIP: c00000000053b3d4 LR: c00000000053e5b0 CTR: c000000000541d70
> REGS: c0000000783c2f60 TRAP: 0700 Not tainted (3.1.0-autokern1)
> MSR: 8000000000029032 <EE,ME,CE,IR,DR> CR: 24002024 XER: 20000002
> TASK = c0000000783b8000[1] 'swapper' THREAD: c0000000783c0000 CPU: 0
> GPR00: 0000000000000001 c0000000783c31e0 c000000000cf38b0 c00000000239a9d0
> GPR04: c000000000cbe8f8 0000000000000000 c0000000783c3040 0000000000000000
> GPR08: c000000075daf488 c000000078a3b7ff c000000000bcacc8 0000000000000000
> GPR12: 0000000044002028 c000000007ffb000 0000000002e40000 000000000099b800
> GPR16: 0000000000000000 c000000000bba5fc c000000000a61db8 0000000000000000
> GPR20: 0000000001b77200 0000000000000000 c000000078990000 0000000000000001
> GPR24: c000000002396828 0000000000000000 0000000000000000 c000000078a3b938
> GPR28: fffffffffffffffa c0000000008ad2c0 c000000000c7faa8 c00000000239a9d0
> NIP [c00000000053b3d4] .scsi_free_queue+0x24/0x90
> LR [c00000000053e5b0] .scsi_alloc_sdev+0x280/0x2e0
> Call Trace:
> [c0000000783c31e0] [c000000000c7faa8] wireless_seq_fops+0x278d0/0x2eb88 (unreliable)
> [c0000000783c3270] [c00000000053e5b0] .scsi_alloc_sdev+0x280/0x2e0
> [c0000000783c3330] [c00000000053eba0] .scsi_probe_and_add_lun+0x390/0xb40
> [c0000000783c34a0] [c00000000053f7ec] .__scsi_scan_target+0x16c/0x650
> [c0000000783c35f0] [c00000000053fd90] .scsi_scan_channel+0xc0/0x100
> [c0000000783c36a0] [c00000000053fefc] .scsi_scan_host_selected+0x12c/0x1c0
> [c0000000783c3750] [c00000000083dcb4] .ipr_probe+0x2c0/0x390
> [c0000000783c3830] [c0000000003f50b4] .local_pci_probe+0x34/0x50
> [c0000000783c38a0] [c0000000003f5f78] .pci_device_probe+0x148/0x150
> [c0000000783c3950] [c0000000004e1e8c] .driver_probe_device+0xdc/0x210
> [c0000000783c39f0] [c0000000004e20cc] .__driver_attach+0x10c/0x110
> [c0000000783c3a80] [c0000000004e1228] .bus_for_each_dev+0x98/0xf0
> [c0000000783c3b30] [c0000000004e1bf8] .driver_attach+0x28/0x40
> [c0000000783c3bb0] [c0000000004e07d8] .bus_add_driver+0x218/0x340
> [c0000000783c3c60] [c0000000004e2a2c] .driver_register+0x9c/0x1b0
> [c0000000783c3d00] [c0000000003f62d4] .__pci_register_driver+0x64/0x140
> [c0000000783c3da0] [c000000000b99f88] .ipr_init+0x4c/0x68
> [c0000000783c3e20] [c00000000000ad24] .do_one_initcall+0x1a4/0x1e0
> [c0000000783c3ee0] [c000000000b512d0] .kernel_init+0x14c/0x1fc
> [c0000000783c3f90] [c000000000022468] .kernel_thread+0x54/0x70
> Instruction dump:
> ebe1fff8 7c0803a6 4e800020 7c0802a6 fba1ffe8 fbe1fff8 7c7f1b78 f8010010
> f821ff71 e8030398 3120ffff 7c090110 <0b000000> e86303b0 482de065 60000000
> ---[ end trace 759bed76a85e8dec ]---
> scsi 0:0:1:0: Direct-Access IBM-ESXS MAY2036RC T106 PQ: 0 ANSI: 5
> ------------[ cut here ]------------
>
> I get lots more of these. The obvious commit to point the finger at
> is 3308511c93e6 ("[SCSI] Make scsi_free_queue() kill pending SCSI
> commands") but the root cause may be something different.
Caused by
commit f7c9c6bb14f3104608a3a83cadea10a6943d2804
Author: Anton Blanchard <anton@samba.org>
Date: Thu Nov 3 08:56:22 2011 +1100
[SCSI] Fix block queue and elevator memory leak in scsi_alloc_sdev
Doesn't completely do the teardown. The true fix is to do a proper
teardown instead of hand rolling it
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Tested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: stable@kernel.org #2.6.38+
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild
* 'trivial' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
scsi: drop unused Kconfig symbol
pci: drop unused Kconfig symbol
stmmac: drop unused Kconfig symbol
x86: drop unused Kconfig symbol
powerpc: drop unused Kconfig symbols
powerpc: 40x: drop unused Kconfig symbol
mips: drop unused Kconfig symbols
openrisc: drop unused Kconfig symbols
arm: at91: drop unused Kconfig symbol
samples: drop unused Kconfig symbol
m32r: drop unused Kconfig symbol
score: drop unused Kconfig symbols
sh: drop unused Kconfig symbol
um: drop unused Kconfig symbol
sparc: drop unused Kconfig symbol
alpha: drop unused Kconfig symbol
Fix up trivial conflict in drivers/net/ethernet/stmicro/stmmac/Kconfig
as per Michal: the STMMAC_DUAL_MAC config variable is still unused and
should be deleted.
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (45 commits)
[SCSI] Fix block queue and elevator memory leak in scsi_alloc_sdev
[SCSI] scsi_dh_alua: Fix the time inteval for alua rtpg commands
[SCSI] scsi_transport_iscsi: Fix documentation os parameter
[SCSI] mv_sas: OCZ RevoDrive3 & zDrive R4 support
[SCSI] libfc: improve flogi retries to avoid lport stuck
[SCSI] libfc: avoid exchanges collision during lport reset
[SCSI] libfc: fix checking FC_TYPE_BLS
[SCSI] edd: Treat "XPRS" host bus type the same as "PCI"
[SCSI] isci: overriding max_concurr_spinup oem parameter by max(oem, user)
[SCSI] isci: revert bcn filtering
[SCSI] isci: Fix hard reset timeout conditions.
[SCSI] isci: No need to manage the pending reset bit on pending requests.
[SCSI] isci: Remove redundant isci_request.ttype field.
[SCSI] isci: Fix task management for SMP, SATA and on dev remove.
[SCSI] isci: No task_done callbacks in error handler paths.
[SCSI] isci: Handle task request timeouts correctly.
[SCSI] isci: Fix tag leak in tasks and terminated requests.
[SCSI] isci: Immediately fail I/O to removed devices.
[SCSI] isci: Lookup device references through requests in completions.
[SCSI] ipr: add definitions for additional adapter
...
|
|
* 'for-3.2/drivers' of git://git.kernel.dk/linux-block: (30 commits)
virtio-blk: use ida to allocate disk index
hpsa: add small delay when using PCI Power Management to reset for kump
cciss: add small delay when using PCI Power Management to reset for kump
xen/blkback: Fix two races in the handling of barrier requests.
xen/blkback: Check for proper operation.
xen/blkback: Fix the inhibition to map pages when discarding sector ranges.
xen/blkback: Report VBD_WSECT (wr_sect) properly.
xen/blkback: Support 'feature-barrier' aka old-style BARRIER requests.
xen-blkfront: plug device number leak in xlblk_init() error path
xen-blkfront: If no barrier or flush is supported, use invalid operation.
xen-blkback: use kzalloc() in favor of kmalloc()+memset()
xen-blkback: fixed indentation and comments
xen-blkfront: fix a deadlock while handling discard response
xen-blkfront: Handle discard requests.
xen-blkback: Implement discard requests ('feature-discard')
xen-blkfront: add BLKIF_OP_DISCARD and discard request struct
drivers/block/loop.c: remove unnecessary bdev argument from loop_clr_fd()
drivers/block/loop.c: emit uevent on auto release
drivers/block/cpqarray.c: use pci_dev->revision
loop: always allow userspace partitions and optionally support automatic scanning
...
Fic up trivial header file includsion conflict in drivers/block/loop.c
|
|
When looking at memory consumption issues I noticed quite a
lot of memory in the kmalloc-2048 bucket:
OBJS ACTIVE USE OBJ SIZE SLABS OBJ/SLAB CACHE SIZE NAME
6561 6471 98% 2.30K 243 27 15552K kmalloc-2048
Over 15MB. slub debug shows that cfq is responsible for almost
all of it:
# sort -nr /sys/kernel/slab/kmalloc-2048/alloc_calls
6402 .cfq_init_queue+0xec/0x460 age=43423/43564/43655 pid=1 cpus=4,11,13
In scsi_alloc_sdev we do scsi_alloc_queue but if slave_alloc
fails we don't free it with scsi_free_queue.
The patch below fixes the issue:
OBJS ACTIVE USE OBJ SIZE SLABS OBJ/SLAB CACHE SIZE NAME
135 72 53% 2.30K 5 27 320K kmalloc-2048
# cat /sys/kernel/slab/kmalloc-2048/alloc_calls
3 .cfq_init_queue+0xec/0x460 age=3811/3876/3925 pid=1 cpus=4,11,13
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@kernel.org> #2.6.38+
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
This patch corrects the retry interval for alua rtpg command. Purpose was to retry the commands in seconds.
But that was not happening. Reason is msleep takes argument in milliseconds.
Also added minor text after successful attach.
Signed-off-by: Babu Moger <babu.moger@netapp.com>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Fixes documentation of a parameter of iscsi_bsg_host_add function to silence
to make htmldocs
Signed-off-by: Marcos Paulo de Souza <marcos.mage@gmail.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
The module.h header was implicitly present everywhere, so files
with no explicit include of the module infrastructure would build
anyway. We are now removing the implicit include, and so we need
to call out the module.h file that we need explicitly.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
For the basic SCSI infrastructure files that are exporting symbols
but not modules themselves, add in the basic export.h header file
to allow the exports.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Michal Marek <mmarek@suse.cz>
|
|
In the OCZ RevoDrive3/zDrive R4 series, the "OCZ SuperScale Storage
Controller" with "Virtualized Controller Architecture 2.0" really seems
to be a Marvell 88SE9485 part, with OCZ firmware/BIOS.
Developed and tested on OCZ RevoDrive3 120GB [PCI 1b85:1021]
Should work on:
- OCZ RevoDrive3 (2x SandForce 2281)
- OCZ RevoDrive3 X2 (4x SandForce 2281)
- OCZ zDrive R4 CM84 (4x SandForce 2281)
- OCZ zDrive R4 CM88 (8x SandForce 2281)
- OCZ zDrive R4 RM84 (4x SandForce 2582)
- OCZ zDrive R4 RM88 (8x SandForce 2582)
All of this because a friend recently bought a OCZ RevoDrive3 and was
bitten by the lack of Linux support.
Notes from testing:
-------------------
- SMART works.
- VPD Device Identification is "OCZ-REVODRIVE3"
- Thin provisioning/TRIM seems to be implemented as WRITE SAME UNMAP,
with deterministic (non-zero) read after TRIM, but I'm not sure if it
works 100% in my testing.
- Some of the tuning in the firmware seems to ensure much better
performance when in a RAID0 setup than using the two devices
seperately.
I have not tested booting from the SSD, because all of this was
developed and tested remotely from the actual hardware.
Signed-off-by: Robin H. Johnson <robbat2@gentoo.org>
Thanks-To: Gordon Pritchard <gordp@sfu.ca>
Acked-by: Xiangliang Yu <yuxiangl@marvell.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Adds more cases to do flogi retry, now also retry
on getting bad response due to either no ELS response
or flogi response payload length not large enough.
In those cases flogi was not retried and that
was leaving lport offline.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Currently timer delay is large and is using msleep to avoid
avoid exchanges collision across lport reset, so instead
do this by initializing exches pool indexes during
reset also.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
