Age | Commit message (Collapse) | Author |
|
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (110 commits)
[SCSI] qla2xxx: Refactor call to qla2xxx_read_sfp for thermal temperature.
[SCSI] qla2xxx: Unify the read/write sfp mailbox command routines.
[SCSI] qla2xxx: Clear complete initialization control block.
[SCSI] qla2xxx: Allow an override of the registered maximum LUN.
[SCSI] qla2xxx: Add host number in reset and quiescent message logs.
[SCSI] qla2xxx: Correctly read sfp single byte mailbox register.
[SCSI] qla2xxx: Add qla82xx_rom_unlock() function.
[SCSI] qla2xxx: Log if qla82xx firmware fails to load from flash.
[SCSI] qla2xxx: Use passed in host to initialize local scsi_qla_host in queuecommand function
[SCSI] qla2xxx: Correct buffer start in edc sysfs debug print.
[SCSI] qla2xxx: Update firmware version after flash update for ISP82xx.
[SCSI] qla2xxx: Fix hang during driver unload when vport is active.
[SCSI] qla2xxx: Properly set the dsd_list_len for dsd_chaining in cmd type 6.
[SCSI] qla2xxx: Fix virtual port failing to login after chip reset.
[SCSI] qla2xxx: Fix vport delete hang when logins are outstanding.
[SCSI] hpsa: Change memset using sizeof(ptr) to sizeof(*ptr)
[SCSI] ipr: Rate limit DMA mapping errors
[SCSI] hpsa: add P2000 to list of shared SAS devices
[SCSI] hpsa: do not attempt PCI power management reset method if we know it won't work.
[SCSI] hpsa: remove superfluous sleeps around reset code
...
|
|
Creating and destroying fcoe interface in a tight loop leads to a system
deadlock with the following call traces:
Call Trace:
[<ffffffff814f4b3d>] schedule_timeout+0x1fd/0x2c0
[<ffffffff814f469f>] ? wait_for_common+0x4f/0x190
[<ffffffff814f469f>] ? wait_for_common+0x4f/0x190
[<ffffffff814f4737>] wait_for_common+0xe7/0x190
[<ffffffff81042fa0>] ? default_wake_function+0x0/0x20
[<ffffffff81082c2d>] ? trace_hardirqs_on+0xd/0x10
[<ffffffff814f48bd>] wait_for_completion+0x1d/0x20
[<ffffffff81066d90>] flush_workqueue+0x290/0x5f0
[<ffffffff81066b00>] ? flush_workqueue+0x0/0x5f0
[<ffffffff81067148>] destroy_workqueue+0x38/0x340
[<ffffffffa0260289>] fc_remove_host+0x1b9/0x1f0 [scsi_transport_fc]
[<ffffffffa02ed195>] bnx2fc_if_destroy+0xc5/0x1f0 [bnx2fc]
[<ffffffffa02ed33a>] bnx2fc_destroy+0x7a/0x100 [bnx2fc]
[<ffffffffa02c789b>] fcoe_transport_destroy+0x9b/0x1b0 [libfcoe]
[<ffffffff81069ec2>] param_attr_store+0x52/0x80
[<ffffffff81069976>] module_attr_store+0x26/0x30
[<ffffffff8119e726>] sysfs_write_file+0xe6/0x170
[<ffffffff81134710>] vfs_write+0xd0/0x1a0
[<ffffffff811348e4>] sys_write+0x54/0xa0
[<ffffffff81002e02>] system_call_fastpath+0x16/0x1b
Call Trace:
[<ffffffff81074865>] async_synchronize_cookie_domain+0x75/0x120
[<ffffffff8106caa0>] ? autoremove_wake_function+0x0/0x40
[<ffffffff81074925>] async_synchronize_cookie+0x15/0x20
[<ffffffff8107494c>] async_synchronize_full+0x1c/0x40
[<ffffffffa0057466>] sd_remove+0x36/0xc0 [sd_mod]
[<ffffffff81358a75>] __device_release_driver+0x75/0xe0
[<ffffffff81358bef>] device_release_driver+0x2f/0x50
[<ffffffff81357aee>] bus_remove_device+0xbe/0x120
[<ffffffff813553ef>] device_del+0x12f/0x1e0
[<ffffffff8137454d>] __scsi_remove_device+0xbd/0xc0
[<ffffffff81374585>] scsi_remove_device+0x35/0x50
[<ffffffff813746a7>] __scsi_remove_target+0xe7/0x110
[<ffffffff81374730>] ? __remove_child+0x0/0x30
[<ffffffff81374753>] __remove_child+0x23/0x30
[<ffffffff81354a2c>] device_for_each_child+0x4c/0x80
[<ffffffff81374703>] scsi_remove_target+0x33/0x60
[<ffffffffa02622c6>] fc_starget_delete+0x26/0x30 [scsi_transport_fc]
[<ffffffffa026271a>] fc_rport_final_delete+0xaa/0x200 [scsi_transport_fc]
[<ffffffff8106585a>] process_one_work+0x1aa/0x540
[<ffffffff810657eb>] ? process_one_work+0x13b/0x540
[<ffffffffa0262670>] ? fc_rport_final_delete+0x0/0x200 [scsi_transport_fc]
[<ffffffff81067ac9>] worker_thread+0x179/0x410
[<ffffffff81067950>] ? worker_thread+0x0/0x410
[<ffffffff8106c546>] kthread+0xb6/0xc0
[<ffffffff8103879b>] ? finish_task_switch+0x4b/0xe0
[<ffffffff81003ca4>] kernel_thread_helper+0x4/0x10
[<ffffffff814f7994>] ? restore_args+0x0/0x30
[<ffffffff8106c490>] ? kthread+0x0/0xc0
[<ffffffff81003ca0>] ? kernel_thread_helper+0x0/0x10
fc_remove_host() waits for flushing the workqueue, but it is stuck at flushing
the first work. The first work doesnt complete, because it is waiting for async
layer to complete the IOs. The async layer cannot complete the IO as the
terminate_rport_io for the second work was not called, which will be called
only when the first work completes. Hence the deadlock. To resolve this
deadlock, the workqueue allocation has been modified from
create_singlethread_workqueue() to alloc_workqueue().
In addition, fc_terminate_rport_io() should be called before the
scsi_flush_work() to avoid the similar deadlock as above.
scsi fc alloc queue. move terminate rport io before flush
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
We are currently using this flag to check whether it's safe
to call into ->request_fn(). If it is set, we punt to kblockd.
But we get a lot of false positives and excessive punts to
kblockd, which hurts performance.
The only real abuser of this infrastructure is SCSI. So export
the async queue run and convert SCSI over to use that. There's
room for improvement in that SCSI need not always use the async
call, but this fixes our performance issue and they can fix that
up in due time.
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
Instead of overloading __blk_run_queue to force an offload to kblockd
add a new blk_run_queue_async helper to do it explicitly. I've kept
the blk_queue_stopped check for now, but I suspect it's not needed
as the check we do when the workqueue items runs should be enough.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
|
|
Conflicts:
block/blk-core.c
block/blk-flush.c
drivers/md/raid1.c
drivers/md/raid10.c
drivers/md/raid5.c
fs/nilfs2/btnode.c
fs/nilfs2/mdt.c
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
Code has been converted over to the new explicit on-stack plugging,
and delay users have been converted to use the new API for that.
So lets kill off the old plugging along with aops->sync_page().
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
__blk_run_queue() automatically either calls q->request_fn() directly
or schedules kblockd depending on whether the function is recursed.
blk-flush implementation needs to be able to explicitly choose
kblockd. Add @force_kblockd.
All the current users are converted to specify %false for the
parameter and this patch doesn't introduce any behavior change.
stable: This is prerequisite for fixing ide oops caused by the new
blk-flush implementation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jan Beulich <JBeulich@novell.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
This adds a fc host dev loss sysfs file. Instead of
calling into the driver using the get_host_def_dev_loss_tmo
callback, we allow drivers to init the dev loss like is done
for other fc host params, and then the fc class will handle
updating the value if the user writes to the new sysfs file.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
When an rport is "blocked" and a bsg request is received, the bsg request gets
placed on the queue but the queue stalls. If the fc object is then deleted - the
bsg queue never restarts and keeps the reference on the object, and stops the
overall teardown.
This patch restarts the bsg queue on teardown and drains any pending requests,
allowing the teardown to succeed.
Signed-off-by: Carl Lajeunesse <carl.lajeunesse@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
This patch adds a fc_host setting to store the
default dev_loss_tmo. It is used if the driver
has a callack to get the value from the LLD. If
the callback is not set, then we use the fc class
module default value.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Cc: Adaptec OEM Raid Solutions <aacraid@adaptec.com>
Cc: "James E.J. Bottomley" <James.Bottomley@suse.de>
Cc: James Smart <james.smart@emulex.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
If the scsi eh is running and then a FC LLD calls
fc_remote_port_delete, the SCSI commands sent from the eh will fail.
To prevent this, a FC LLD can call fc_block_scsi_eh from the eh
callback, blocking the eh thread until the dev_loss_tmo fires or the
remote port is available again.
If (e.g. for a multipathing setup) the dev_loss_tmo is set to a very
large value, thus preventing the scsi device removal , the scsi eh can
block for a long time. For multipathing, the fast_io_fail_tmo is then
set to a low value to detect path problems sooner.
This patch introduces a new return code FAST_IO_FAIL. The function
fc_block_scsi_eh now returns FAST_IO_FAIL when the fast_io_fail_tmo
fires. This indicates that the LLD terminated all pending I/O requests
and there are no more pending SCSI commands for the scsi eh to wait
for. This return code can be passed back to the scsi eh to stop the
escalation and finish the recovery process for this device.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
The rport structure defines dev_loss_tmo as u32, which is
later multiplied with HZ to get the actual timeout value.
This might overflow for large dev_loss_tmo values. So we
should be better using u64 as intermediate variables here
to protect against overflow.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Acked-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] qla1280: retain firmware for error recovery
[SCSI] attirbute_container: Initialize sysfs attributes with sysfs_attr_init
[SCSI] advansys: fix regression with request_firmware change
[SCSI] qla2xxx: Updated version number to 8.03.02-k2.
[SCSI] qla2xxx: Prevent sending mbx commands from sysfs during isp reset.
[SCSI] qla2xxx: Disable MSI on qla24xx chips other than QLA2432.
[SCSI] qla2xxx: Check to make sure multique and CPU affinity support is not enabled at the same time.
[SCSI] qla2xxx: Correct vp_idx checking during PORT_UPDATE processing.
[SCSI] qla2xxx: Honour "Extended BB credits" bit for CNAs.
[SCSI] scsi_transport_fc: Make sure commands are completed when rport is offline
[SCSI] libiscsi: Fix recovery slowdown regression
|
|
implicit slab.h inclusion from percpu.h
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
|
|
blk_end_request doesn't complete a bidi request
successfully
The unfinished request eventually triggers a panic in
timeout handling routine fc_bsg_job_timeout as
req->special is NULL
Use blk_end_request_all to end the request unconditionally
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Acked-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
The issue occur while deleting 60 virtual ports through the sys
interface /sys/class/fc_vports/vport-X/vport_delete. It happen while in
a mistake each request sent twice for the same vport. This interface is
asynchronous, entering the delete request into a work queue, allowing
more than one request to enter to the delete work queue. The result is a
NULL pointer. The first request already delete the vport, while the
second request got a pointer to the vport before the device destroyed.
Re-create vport later cause system freeze.
Solution: Check vport flags before entering the request to the work queue.
[jejb: fixed int<->long problem on spinlock flags variable]
Signed-off-by: Gal Rosen <galr@storwize.com>
Acked-by: James Smart <james.smart@emulex.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Currently dev_loss_tmo is capped by SCSI_DEVICE_BLOCK_MAX_TIMEOUT.
This causes problem with multipathing when the 'no_path_retry' setting
exceeds the dev_loss_tmo setting, as then the system might run into
a deadlock when all paths have been removed temporarily for longer
than dev_loss_tmo.
The principal reasons for the capping has been that we should
not allow a remote port to remain in status 'blocked' indefinitely,
so the capping is there to ensure that the port status is being reset
eventually.
However, the fast_io_fail_tmo will also move the remote port out of
the 'blocked' state, so for any HBA driver implementing both the
capping should really be on the fast_io_fail_tmo, and not on the
dev_loss_tmo.
This patch implements just that, ie the fast_io_fail_tmo is capped
to SCSI_DEVICE_BLOCK_TIMEOUT and the capping is removed from
dev_loss_tmo when fast_io_fail_tmo is set.
This allows us to synchronize the dev_loss_tmo setting to the
'no_path_retry' setting from multipathing thus avoiding the deadlock.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Acked-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
The hardware used with zfcp cannot abort a currently pending CT or ELS
request. Therefore we need the option to postpone the timeout
triggered request abort within the fc layer, since there is nothing
zfcp can do to stop the request at this point.
Cc: James Smart <James.Smart@emulex.com>
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
If transport_class_register fails we should unregister any
registered classes, or we will leak memory or other
resources.
I did a quick modprobe of scsi_transport_fc to test the
patch.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (222 commits)
[SCSI] zfcp: Remove flag ZFCP_STATUS_FSFREQ_TMFUNCNOTSUPP
[SCSI] zfcp: Activate fc4s attributes for zfcp in FC transport class
[SCSI] zfcp: Block scsi_eh thread for rport state BLOCKED
[SCSI] zfcp: Update FSF error reporting
[SCSI] zfcp: Improve ELS ADISC handling
[SCSI] zfcp: Simplify handling of ct and els requests
[SCSI] zfcp: Remove ZFCP_DID_MASK
[SCSI] zfcp: Move WKA port to zfcp FC code
[SCSI] zfcp: Use common code definitions for FC CT structs
[SCSI] zfcp: Use common code definitions for FC ELS structs
[SCSI] zfcp: Update FCP protocol related code
[SCSI] zfcp: Dont fail SCSI commands when transitioning to blocked fc_rport
[SCSI] zfcp: Assign scheduled work to driver queue
[SCSI] zfcp: Remove STATUS_COMMON_REMOVE flag as it is not required anymore
[SCSI] zfcp: Implement module unloading
[SCSI] zfcp: Merge trace code for fsf requests in one function
[SCSI] zfcp: Access ports and units with container_of in sysfs code
[SCSI] zfcp: Remove suspend callback
[SCSI] zfcp: Remove global config_mutex
[SCSI] zfcp: Replace local reference counting with common kref
...
|
|
If the port state is blocked and the fast io fail tmo has
fired then this patch will fail bsg requests immediately.
This is needed if userspace is sending IOs to test the transport
like with fcping, so it will not have to wait for the dev loss tmo.
With this patch he bsg req fast io fail code behaves like the normal
and sg io/passthrough fast io fail.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-By: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Move the duplicated code from FC LLDs to SCSI FC transport class.
Acked-by: James Smart <james.smart@emulex.com>
Acked-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Acked-by: Abhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
There are three error paths in the FC passthru code where
job->reply->reply_payload_rcv_len does not get initialized,
resulting in the WARN_ON in fc_bsg_jobdone going off. This patch
fixes this. An example of one of the WARN_ON messages seen:
Badness at drivers/scsi/scsi_transport_fc.c:3424
NIP: d000000000bf21ac LR: d000000000bf2684 CTR: c0000000003f753c
REGS: c00000004eb03430 TRAP: 0700 Not tainted (2.6.32-rc4-git)
MSR: 8000000000029032 <EE,ME,CE,IR,DR> CR: 24008444 XER: 00000012
TASK = c00000004c3fc9c0[3243] 'fcping' THREAD: c00000004eb00000 CPU: 0
GPR00: 0000000000000001 c00000004eb036b0 d000000000c01da0 000000004bf17fc0
GPR04: c00000004cd256a0 c00000007e011ce0 c00000007e011d00 c00000004e718000
GPR08: c00000004cd256a0 c00000004eb03ad0 c00000004cd25a90 0000000000000020
GPR12: d000000000bf7848 c000000000b62600 0000000000000060 fffffffffffffff4
GPR16: ffffffffffffffd6 c00000004c7a3060 ffffffff80000003 c00000004b0f0310
GPR20: c00000004e71b180 c00000004c7a3060 0000000000000004 0000000000000000
GPR24: c00000004e71b000 c00000004c7a3000 c00000004b0f0000 c00000004e718000
GPR28: c00000004cd256a0 c00000004cd25a90 d000000000c01db0 c00000004e01d680
NIP [d000000000bf21ac] .fc_bsg_jobdone+0x64/0x9c [scsi_transport_fc]
LR [d000000000bf2684] .fc_bsg_request_handler+0x4a0/0x564 [scsi_transport_fc]
Call Trace:
[c00000004eb036b0] [c0000000003f755c] .get_device+0x20/0x38 (unreliable)
[c00000004eb03720] [d000000000bf2684] .fc_bsg_request_handler+0x4a0/0x564 [scsi_transport_fc]
[c00000004eb03820] [c0000000002c9b5c] .__generic_unplug_device+0x58/0x70
[c00000004eb038a0] [c0000000002ce9fc] .blk_execute_rq_nowait+0x70/0xf4
[c00000004eb03930] [c0000000002ceb2c] .blk_execute_rq+0xac/0x100
[c00000004eb03a60] [c0000000002d51b4] .bsg_ioctl+0x1fc/0x264
[c00000004eb03c10] [c00000000018a89c] .vfs_ioctl+0x54/0xec
[c00000004eb03ca0] [c00000000018b01c] .do_vfs_ioctl+0x640/0x6a8
[c00000004eb03d80] [c00000000018b0fc] .SyS_ioctl+0x78/0xbc
[c00000004eb03e30] [c0000000000085b4] syscall_exit+0x0/0x40
Instruction dump:
8003004c 2fa80000 90090104 38000000 900a0108 419e0038 e9230040 81680108
80690004 7f835840 7c101026 5400f7fe <0b000000> 7d605b78 7f8b1840 409d0008
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-By: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
I was doing some large lun count testing with 2.6.31 and hit
a BUG_ON() in fc_timeout_deleted_rport(), and it seems like it
should have been just a matter of time before someone did.
It seems invalid to set port_state under lock, then expect it to
remain set after releasing the lock. Another thread called
fc_remote_port_add() when the lock was released, changing the
port_state.
This patch removes the BUG_ON and moves the test of the
port_state to inside the host_lock. It's been running for
several weeks now with no ill effect.
Signed-off-by: Michael Reed <mdr@sgi.com>
Acked-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Add missing kernel-doc notation in scsi_transport_fc.c:
Warning(drivers/scsi/scsi_transport_fc.c:3593): No description found for parameter 'q'
Warning(drivers/scsi/scsi_transport_fc.c:3700): No description found for parameter 'q'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Change function parameter name in kernel-doc to match the function's
actual parameter name, to fix 2 kernel-doc warnings.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Fix this:
------------[ cut here ]------------
Badness at block/blk-core.c:244
CPU: 0 Tainted: G W 2.6.31-rc1-00004-gd3a263a #3
Process zfcp_wq (pid: 901, task: 000000002fb7a038, ksp: 000000002f02bc78)
Krnl PSW : 0704300180000000 00000000002141ba (blk_remove_plug+0xb2/0xb8)
R:0 T:1 IO:1 EX:1 Key:0 M:1 W:0 P:0 AS:0 CC:3 PM:0 EA:3
Krnl GPRS: 0000000000000001 0000000000000001 0000000022811440 0000000022811798
000000000027ff4e 0000000000000000 0000000000000000 000000002f00f000
070000000006a0f4 000000002af70000 000000002af2a800 00000000228d1c00
0000000022811440 000000000050c708 000000002f02bca8 000000002f02bc80
Krnl Code: 00000000002141b0: b9140022 lgfr %r2,%r2
00000000002141b4: 07fe bcr 15,%r14
00000000002141b6: a7f40001 brc 15,2141b8
>00000000002141ba: a7f4ffbe brc 15,214136
00000000002141be: 0707 bcr 0,%r7
00000000002141c0: ebaff0680024 stmg %r10,%r15,104(%r15)
00000000002141c6: c0d00017c2a9 larl %r13,50c718
00000000002141cc: a7f13fc0 tmll %r15,16320
Call Trace:
([<000000000050e7d8>] C.272.16122+0x88/0x110)
[<00000000002141ec>] __blk_run_queue+0x2c/0x154
[<000000000028013a>] fc_remote_port_add+0x85e/0x95c
[<000000000037596e>] zfcp_scsi_rport_work+0xe6/0x148
[<000000000006908c>] worker_thread+0x25c/0x318
[<000000000006f10c>] kthread+0x94/0x9c
[<000000000001c2b2>] kernel_thread_starter+0x6/0xc
[<000000000001c2ac>] kernel_thread_starter+0x0/0xc
INFO: lockdep is turned off.
Last Breaking-Event-Address:
[<00000000002141b6>] blk_remove_plug+0xae/0xb8
The FC pass-through support triggers the WARN_ON(!irqs_disabled()) in
blk_plug_device. Since blk_plug_device requires being called with
disabled interrupts, use spin_lock_irqsave in fc_bsg_goose_queue to
disable the interrupts before calling into the block layer.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Acked-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
BUS_ID_SIZE is being removed from the kernel.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
The return value from BSG timout function should be based on the state of the
BSG job. This helps block layer to take selective actions to clean up BSG job.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Acked-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Registered the softirq_done function, since this is requried iby an request
using block level request timeout functionality. This function will be called
by the block layer as part of time out clean process to release the BSG
request.
Moved some of the BSG request completion activities to softirq_done routine to
take care of both normal and timout completions.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Acked-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Attached is the ELS/CT pass-thru patch for the FC Transport. The patch
creates a generic framework that lays on top of bsg and the SGIO v4 ioctl
in order to pass transaction requests to LLDD's.
The interface supports the following operations:
On an fc_host basis:
Request login to the specified N_Port_ID, creating an fc_rport.
Request logout of the specified N_Port_ID, deleting an fc_rport
Send ELS request to specified N_Port_ID w/o requiring a login, and
wait for ELS response.
Send CT request to specified N_Port_ID and wait for CT response.
Login is required, but LLDD is allowed to manage login and decide
whether it stays in place after the request is satisfied.
Vendor-Unique request. Allows a LLDD-specific request to be passed
to the LLDD, and the passing of a response back to the application.
On an fc_rport basis:
Send ELS request to nport and wait for ELS response.
Send CT request to nport and wait for CT response.
The patch also exports several headers from include/scsi such that
they can be available to user-space applications:
include/scsi/scsi.h
include/scsi/scsi_netlink.h
include/scsi/scsi_netlink_fc.h
include/scsi/scsi_bsg_fc.h
For further information, refer to the last RFC:
http://marc.info/?l=linux-scsi&m=123436574018579&w=2
Note: Documentation is still spotty and will be added later.
[bharrosh@panasas.com: update for new block API]
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (119 commits)
[SCSI] scsi_dh_rdac: Retry for NOT_READY check condition
[SCSI] mpt2sas: make global symbols unique
[SCSI] sd: Make revalidate less chatty
[SCSI] sd: Try READ CAPACITY 16 first for SBC-2 devices
[SCSI] sd: Refactor sd_read_capacity()
[SCSI] mpt2sas v00.100.11.15
[SCSI] mpt2sas: add MPT2SAS_MINOR(221) to miscdevice.h
[SCSI] ch: Add scsi type modalias
[SCSI] 3w-9xxx: add power management support
[SCSI] bsg: add linux/types.h include to bsg.h
[SCSI] cxgb3i: fix function descriptions
[SCSI] libiscsi: fix possbile null ptr session command cleanup
[SCSI] iscsi class: remove host no argument from session creation callout
[SCSI] libiscsi: pass session failure a session struct
[SCSI] iscsi lib: remove qdepth param from iscsi host allocation
[SCSI] iscsi lib: have lib create work queue for transmitting IO
[SCSI] iscsi class: fix lock dep warning on logout
[SCSI] libiscsi: don't cap queue depth in iscsi modules
[SCSI] iscsi_tcp: replace scsi_debug/tcp_debug logging with iscsi conn logging
[SCSI] libiscsi_tcp: replace tcp_debug/scsi_debug logging with session/conn logging
...
|
|
Fix typo by adding closing parenthesis.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Currently, netlink_broadcast() reports errors to the caller if no
messages at all were delivered:
1) If, at least, one message has been delivered correctly, returns 0.
2) Otherwise, if no messages at all were delivered due to skb_clone()
failure, return -ENOBUFS.
3) Otherwise, if there are no listeners, return -ESRCH.
With this patch, the caller knows if the delivery of any of the
messages to the listeners have failed:
1) If it fails to deliver any message (for whatever reason), return
-ENOBUFS.
2) Otherwise, if all messages were delivered OK, returns 0.
3) Otherwise, if no listeners, return -ESRCH.
In the current ctnetlink code and in Netfilter in general, we can add
reliable logging and connection tracking event delivery by dropping the
packets whose events were not successfully delivered over Netlink. Of
course, this option would be settable via /proc as this approach reduces
performance (in terms of filtered connections per seconds by a stateful
firewall) but providing reliable logging and event delivery (for
conntrackd) in return.
This patch also changes some clients of netlink_broadcast() that
may report ENOBUFS errors via printk. This error handling is not
of any help. Instead, the userspace daemons that are listening to
those netlink messages should resync themselves with the kernel-side
if they hit ENOBUFS.
BTW, netlink_broadcast() clients include those that call
cn_netlink_send(), nlmsg_multicast() and genlmsg_multicast() since they
internally call netlink_broadcast() and return its error value.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When we reworked the transport for the rport lifetimes, in cases where the
rport was reused as a container for tgt id bindings, we inadvertantly
removed the callback to the driver indicating that dev_loss_tmo had fired.
This patch restores that functionality.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
[jejb: limit ioctl to returning 20 characters to avoid overrun
on long device names and add a few more conversions]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Pre-emptively terminate i/o on the rport if dev_loss_tmo has fired.
The desire is to terminate everything, so that the i/o is cleaned up
prior to the sdev's being unblocked, thus any outstanding timeouts/aborts
are avoided.
Also, we do this early enough such that the rport's port_id field is
still valid. FCOE libFC code needs this info to find the i/o's to
terminate.
Signed-off-by: James Smart <james.smart@emulex.com>
[michaelc@cs.wisc.edu: remove extra scsi_target_unblock call]
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
When we block a rport and the driver implements the terminate
callback we will fail IO that was running quickly. However
IO that was in the scsi_device/block queue sits there until
the dev_loss_tmo fires, and this can make it look like IO is
lost because new IO will get executed but that IO stuck in
the blocked queue sits there for some time longer.
With this patch when the fast io fail tmo fires, we will
fail the blocked IO and any new IO. This patch also allows
all drivers to partially support the fast io fail tmo. If the
terminate io callback is not implemented, we will still fail blocked
IO and any new IO, so multipath can handle that.
This patch also allows the fc and iscsi classes to implement the
same behavior. The timers are just unfornately named differently.
This patch also fixes the problem where drivers were unblocking
the target in their terminate callback, which was needed for
rport removal, but for fast io fail timeout it would cause
IO to bounce arround the scsi/block layer and the LLD queuecommand.
And it for drivers that could have IO stuck but did not have
a terminate callback the unblock calls in the class will fix
them.
v2.
- fix up bit setting style to meet JamesS's pref.
- Broke out new host byte error changes to make it easier to read.
- added JamesS's ack from list.
v1
- initial patch
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (37 commits)
[SCSI] zfcp: fix double dbf id usage
[SCSI] zfcp: wait on SCSI work to be finished before proceeding with init dev
[SCSI] zfcp: fix erp list usage without using locks
[SCSI] zfcp: prevent fc_remote_port_delete calls for unregistered rport
[SCSI] zfcp: fix deadlock caused by shared work queue tasks
[SCSI] zfcp: put threshold data in hba trace
[SCSI] zfcp: Simplify zfcp data structures
[SCSI] zfcp: Simplify get_adapter_by_busid
[SCSI] zfcp: remove all typedefs and replace them with standards
[SCSI] zfcp: attach and release SAN nameserver port on demand
[SCSI] zfcp: remove unused references, declarations and flags
[SCSI] zfcp: Update message with input from review
[SCSI] zfcp: add queue_full sysfs attribute
[SCSI] scsi_dh: suppress comparison warning
[SCSI] scsi_dh: add Dell product information into rdac device handler
[SCSI] qla2xxx: remove the unused SCSI_QLOGIC_FC_FIRMWARE option
[SCSI] qla2xxx: fix printk format warnings
[SCSI] qla2xxx: Update version number to 8.02.01-k8.
[SCSI] qla2xxx: Ignore payload reserved-bits during RSCN processing.
[SCSI] qla2xxx: Additional residual-count corrections during UNDERRUN handling.
...
|
|
Right now SCSI and others do their own command timeout handling.
Move those bits to the block layer.
Instead of having a timer per command, we try to be a bit more clever
and simply have one per-queue. This avoids the overhead of having to
tear down and setup a timer for each command, so it will result in a lot
less timer fiddling.
Signed-off-by: Mike Anderson <andmike@linux.vnet.ibm.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
There's already a fc_vport_termintate() call exported by
the transport. This patch adds a symmetric call to the API to allow
an NPIV-capable LLD to instantiate vports sans user intervention.
Additional comments/updates:
Re: scsi_fc_transport.txt
Add a function prototype for fc_vport_terminate similar to what's
done for fc_vport_create
Re: fc_vport_create
I recommend we pass the channel number in fc_vport_create rather
than fixing it at zero.
Also, ids->vport_type should be set to FC_PORTTYPE_NPIV prior to
calling fc_vport_create. The comment is also meaningless.
Added-by and
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
[jejb: fixed up a ton of missed conversions.
All of you are on notice this has happened, driver trees will now
need to be rebased]
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: SCSI List <linux-scsi@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Kobjects do not have a limit in name size since a while, so stop
pretending that they do.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Way back when, when the fc_user_scan routine was created, it kept some
of its original logic that walked the rport list and kicked off a scan.
Unfortunately, it didn't keep any of the locking around the rport list,
nor did it consider the synchronous nature of the scan invoked. The result,
there are some scan requests where the rport list changes, thus a subsequent
scan is called on a bogus rport structure and the system NMI's.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
It's big, but there doesn't seem to be a way to split it up smaller...
Signed-off-by: Tony Jones <tonyj@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Add Documentation/DocBook/scsi_midlayer.tmpl, add to Makefile, and update
lots of kerneldoc comments in drivers/scsi/*.
Updated with comments from Stefan Richter, Stephen M. Cameron,
James Bottomley and Randy Dunlap.
Signed-off-by: Rob Landley <rob@landley.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|