| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Fix SYSFS interface issues.
- In the lpfc_sli4_pdev_status_reg_wait() routine, after initial 100ms delay
following write to PHYSDEV_CONTROL register for the firmware reaction, check
the RN bit and ERR bit of the SLIPORT_STATUS register. If none of them
became 1, the previous PHYSDEV_CONTROL register should be considered failed
due to lack of privilege and error for no permission should be returned
immediately without getting into the wait for RDY bits on the SLIPORT_STATUS
register.
- Remove the driver check on dev->is_physfn before proceed to perform the
PHYSDEV_CONTROL register write, and let the PCI function's privilege
setting and driver handling of PHYSDEV_CONTROL register write failure to
handle the reset-ability through the SLI port.
- Added key to ctlreg_write to prevent unauthorized or unexpected write to
the control register.
- Change return to EACCES for sysfs access that are failed because hba_reset
is disabled.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Fix HBA initialization issues
- Swap all values that come from the firmware image on little endian systems.
Created a new bf_get_be macro that does the same as the bf_get_le macro but
for big endian data instead of little endian data.
- Moved the incrementing of temp_offset after the copy
fixed the write object loop to use temp_offset to figure out where the end
of the image is instead of offset.
- Added the necessary codes for properly bringing the driver instance offline
and then trying to bring the port back online with the PCI function IP reset.
If it fails to bring the SLI port back online, it will fall through to
bringing the SLI port to HBA error offline.
- Add a call in the probe_one_s3 and probe_one_s4 routines to get the Modeldesc
- Change OCe50100 to OCe15100
- Made the error log also include the PCI BAR bitmap returned from kernel call
pci_select_bars().
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Fix issues pertaining to SCSI/FC protocol.
- Allow frames destined to 0xFFFFFE to be processed by the driver by matching
that DID with the physical port.
- Call lpfc_sli_issue_iocb with context1 set to ndlp
- In echo command accept function, adjust memcpy to limit memcpy to 1K
- Set LPFC_SLI3_BG_ENABLED properly upon completion.
- Skip the INIT_VFI call in lpfc_register_fcf if the FCF is already
registered and go immediately to initial flogi.
- use "status" variable instead of "ret" variable to hold the return of the
fc_block_scsi_eh.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Change driver version to 8.3.25
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
This patch implements a new FCF failover policy for the lpfc driver. It
allows the driver to choose which FCF to failover to based on the FCF
priority. This patch also introduces a new sysfs parameter
(fcf_failover_policy) to allow the user to choose which FCF failover policy
to use.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Enhancements to Debug infrastructure
- debugfs additions for new hardware.
- Correct stack overflow in lpfc_debugfs_dumpHBASlim_data()
- Correct warning on uninitialized reg_val in lpfc_idiag_drbacc_write()
- Separated the iDiag command for capturing mailbox commands for generic
issue mailbox command entry point and for BSG multi-buffer handling.
- Added capturing dumping capabiliy of mailbox command and external buffer
for the completion of the mailbox command so that the outcome can be
examined.
- Changed all the iDiag command structure data array indexing introduced so
far with properly defined macros.
- Added SLI4 device PCI BAR memory mapped register read/browse, write-by-
value, set-bit, and clear-bit methods for both interface type 0 and
interface type 2.
- Corrected warnings on mbxstatus being uninitialized in error paths in
lpfc_bsg.c
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
PCI and SR-IOV Fixes
- Call pci_save_state after the pci_restore_state completes.
- After calling pci_enable_pcie_error_reporting() and checking the return
value for logging messages from rc, reset rc to 0 to it will not later be
interpreted for error.
- Read PCI config space SR-IOV capability to get the number of VFs supported.
- Check for the PF's supported number of VFs before invoking PCI enable sriov
API call and log error message that user requested number of VFs is beyond
the PF capability if such request is passed in.
- Added check for Physical function with Virtual Functions attached. If so,
first disable all the VFs before proceeding to device reset.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Fabric and Target Discovery Fixes
- Clear FC_VPORT_NEEDS_INIT_VPI flag during completion of REG_VFI mailbox
command.
- Prevent SLI3 Code from unregistering the physical VPI.
- Add an else clause to the code that checks and sets
sp->cmn.request_multiple_Nport to clear the bit.
- Remove a redundant mbox free.
- Modified lpfc_sli4_async_fip_evt to pass in physical VPI toi
lpfc_find_vport_by_vpid function.
- Modified lpfc_find_vport_by_vpid to translate physical VPI to logical VPI
before comparing with vport VPI.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Adapter Interface fixes and changes
- Modify the macro field from lpfc_init_vpi_vpi to lpfc_init_vfi_vpi
- Add the new CQE_CODE_RECEIVE_V1 CQE Code, add code in the driver to handle
the new Code the same as the CQE_CODE_RECEIVE code except that there are
two new checks for this code that will cause the driver to use the new V1
macros for rq_id and fcf_id.
- Fix a bug in lpfc_prep_seq() where the size out of the first CQE was
ONLY being used, even though multiple dmabufs make up the sequence,
each have their own CQE with potentially different sizes.
- Fix bug in lpfc_bsg_ct_unsol_event() where the ulpContext and ulpWord[3]
fields of the XMIT_SEQUENCE64_CX IOCB were being calculated incorrectly.
- Do physical to logical translation before indexing into the active
XRI array.
- Populate physical vpi in the iocb data structure.
- Put the current accumulated total in each IOCB in the chain as we are
walking thru then. The last IOCB in the chain should have the total
length of the sequence.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Miscellaneous Bug fixes and code cleanup
- Fix 16G link speed reporting by adding check for 16G check.
- Change the check and enforcement of MAILBOX_EXT_SIZE (2048B)
to the check and enforcement of BSG_MBOX_SIZE - sizeof(MAILBOX_t) (3840B).
- Instead of waiting for a fixed amount of time after performing firmware
reset, the driver shall wait for the Lancer SLIPORT_STATUS register for the
readiness of the firmware for bring up.
- Add logging to indicate when dynamic parameters are changed.
- Add revision and date to the firmware image format.
- Use revision instead of rev_name to check firmware image version.
- Update temporary offset after memcopy is complete for firmware update.
- Consolidated the use of the macros to get rid of duplicated register
offset definitions.
- Removed the unused second parameter in routine lpfc_bsg_diag_mode_enter()
- Enable debugfs when debugfs is enabled.
- Update function comments for lpfc_sli4_alloc_xri and lpfc_sli4_init_rpi_hdrs.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
T10 DIF Fixes
- Fix the case where the SCSI Host supplies the CRC and driver to controller
protection is on.
- Only support T10 DIF type 1. LBA always goes in ref tag and app tag is not
checked.
- Change the format of the sense data passed up to the SCSI layer to match the
Descriptor Format Sense Data found in SPC-4 sections 4.5.2.1 and 4.5.2.2.
- Fix Slip PDE implementation.
- Remove BUG() in else casein lpfc_sc_to_bg_opcodes.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
fs: Merge split strings
treewide: fix potentially dangerous trailing ';' in #defined values/expressions
uwb: Fix misspelling of neighbourhood in comment
net, netfilter: Remove redundant goto in ebt_ulog_packet
trivial: don't touch files that are removed in the staging tree
lib/vsprintf: replace link to Draft by final RFC number
doc: Kconfig: `to be' -> `be'
doc: Kconfig: Typo: square -> squared
doc: Konfig: Documentation/power/{pm => apm-acpi}.txt
drivers/net: static should be at beginning of declaration
drivers/media: static should be at beginning of declaration
drivers/i2c: static should be at beginning of declaration
XTENSA: static should be at beginning of declaration
SH: static should be at beginning of declaration
MIPS: static should be at beginning of declaration
ARM: static should be at beginning of declaration
rcu: treewide: Do not use rcu_read_lock_held when calling rcu_dereference_check
Update my e-mail address
PCIe ASPM: forcedly -> forcibly
gma500: push through device driver tree
...
Fix up trivial conflicts:
- arch/arm/mach-ep93xx/dma-m2p.c (deleted)
- drivers/gpio/gpio-ep93xx.c (renamed and context nearby)
- drivers/net/r8169.c (just context changes)
|
|
All these are instances of
#define NAME value;
or
#define NAME(params_opt) value;
These of course fail to build when used in contexts like
if(foo $OP NAME)
while(bar $OP NAME)
and may silently generate the wrong code in contexts such as
foo = NAME + 1; /* foo = value; + 1; */
bar = NAME - 1; /* bar = value; - 1; */
baz = NAME & quux; /* baz = value; & quux; */
Reported on comp.lang.c,
Message-ID: <ab0d55fe-25e5-482b-811e-c475aa6065c3@c29g2000yqd.googlegroups.com>
Initial analysis of the dangers provided by Keith Thompson in that thread.
There are many more instances of more complicated macros having unnecessary
trailing semicolons, but this pile seems to be all of the cases of simple
values suffering from the problem. (Thus things that are likely to be found
in one of the contexts above, more complicated ones aren't.)
Signed-off-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Enabling DEBUG_STRICT_USER_COPY_CHECKS causes the following
warning:
In file included from arch/x86/include/asm/uaccess.h:573,
from include/linux/uaccess.h:5,
from include/linux/highmem.h:7,
from include/linux/pagemap.h:10,
from include/linux/blkdev.h:12,
from drivers/scsi/lpfc/lpfc_debugfs.c:21:
In function 'copy_from_user':
arch/x86/include/asm/uaccess_64.h:65:
warning: call to 'copy_from_user_overflow' declared with
attribute warning: copy_from_user() buffer size is not provably
correct
presumably due to buf_size being signed causing GCC to fail to
see that buf_size can't become negative.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Extend BSG infrastructure and add link diagnostics:
- Removed unnecessary copies in handling pass-through mbox cmds.
- Add embedded SLI_CONFIG support for BSG.
- Add multibuffer support.
- Implemented the setting up and tearing down Lancer FC device for performing
internal and external loopback diagnostic tests.
- Implemented the driver support for performing new link diagnostic tests
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
|
|
This patch adds support for hardware that returns resource ids via
extents rather than contiguous ranges.
[jejb: checkpatch.pl fixes]
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
|
|
Add request-firmware support:
- Add support for request_firmware interface for INTF2 SLI4 ports.
- Add ability to reset SLI4 INTF2 ports.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
|
|
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
|
|
Extended hardware support and support dump images:
- Make the size to be MAILBOX_SYSFS_MAX (4096) so that it allows the maximum
sysfs binary access interface possible.
- Add ids and model names for new hardware
- Add capability of inducing SLI4 firmware dump obj file
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
|
|
Miscellaneous Fixes and Corrections
- Remove the memset in the lpfc_sli4_remove_rpi_hdrs call.
- Correct swapping of SGE word 2 relative to offset value
- Reorganize CQ and EQ usage to comply with SLI4 Specification.
- Expand the driver to check the rn bit. Only detect an error if the error bit
is set and the RN bit is NOT set.
- If mailbox completion code is not success AND the mailbox status is success,
then and only then will the driver overwrite the mailbox status.
- When driver initializing device, if the device is on a PCIe bus, set
PCI's "needs fundamental reset" bit so that EEH uses fundamental reset
instead of hot reset for recovery.
- Prevent driver from using new WWN when changed in firmware (until driver
reload)
- When HBA reports maximum SGE size > 0xffffffff (infinite), override
with 0x80000000.
- Fixed potential missed SLI4 device initialization failure conditions.
- Added 100ms delay before driver action following IF_TYPE_2 function reset.
- Reverted patch to UNREG/REG on PLOGI to mapped/unmapped node.
- Add a check for the CVL received flag in the fcf inuse routine to avoid
unregistering the fcf if Devloss fires before Delay discover timer fires.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
b43: fix comment typo reqest -> request
Haavard Skinnemoen has left Atmel
cris: typo in mach-fs Makefile
Kconfig: fix copy/paste-ism for dell-wmi-aio driver
doc: timers-howto: fix a typo ("unsgined")
perf: Only include annotate.h once in tools/perf/util/ui/browsers/annotate.c
md, raid5: Fix spelling error in comment ('Ofcourse' --> 'Of course').
treewide: fix a few typos in comments
regulator: change debug statement be consistent with the style of the rest
Revert "arm: mach-u300/gpio: Fix mem_region resource size miscalculations"
audit: acquire creds selectively to reduce atomic op overhead
rtlwifi: don't touch with treewide double semicolon removal
treewide: cleanup continuations and remove logging message whitespace
ath9k_hw: don't touch with treewide double semicolon removal
include/linux/leds-regulator.h: fix syntax in example code
tty: fix typo in descripton of tty_termios_encode_baud_rate
xtensa: remove obsolete BKL kernel option from defconfig
m68k: fix comment typo 'occcured'
arch:Kconfig.locks Remove unused config option.
treewide: remove extra semicolons
...
|
|
- kenrel -> kernel
- whetehr -> whether
- ttt -> tt
- sss -> ss
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Update driver version to 8.3.22
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
- Fixed the mixed declarations and codes which violate ISO C90
(declarations in subsections that assign at declaration)
- Add BSG data transfer size protection in mailbox command pass-through path
- Invoke BSG job_done while holding spinlock to fix deadlock
- Added support for checking SLI_CONFIG subcommands
- Fixed bug in BSG mailbox size check to non-embedded external buffer
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Fixes related to new hardware
- Restrict driver to look at BAR2 or BAR4 only for if_type 0.
- Allow SLI4 with FCOE_MODE not set for new SLI4 FC adapters.
- Add Temporary RPI field to the ELS request WQE.
- Do not override CT field in issue_els_flogi for SLI4 IF type 2
- For RQ_CREATE_V2 mbx cmd: fill in the rqe_size and page_size for RQ_CREATE.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Miscellaneous fixes
- Do not limit RPI Count to a minimum of 64
- Fix FCFI incorrect on received unsolicited frames.
- Save the FCFI returned in the REG_FCFI mailbox command if it was successful.
- Fixed Vports not sending FDISC after lips.
- Align based on the SLI4_PAGE_SIZE.
- Fixed double byte swap on received RRQ.
- Fixed mask size for the wq_id mask from 0x7F to 0x7FFF.
- Clear FC_FABRIC flag when NPIV LOGO completes (and add a log message).
- Modified driver to skip round robin only when ulpStatus==LOCAL_REJECT
and word4=SEQUENCE_TIMEOUT to prevent FLOGI to disconnected FCF.
- Don't add rport if driver unloading
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Debugfs enhancements
- Added iDiag support for new adapters.
- Added queue entry access methods.
- Fix host/port index in decimal
- Added Doorbell register access methods.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Stop using cmd->serial_number in printks.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Fast-forwarded to current state of Linus' tree as there are patches to be
applied for files that didn't exist on the old branch.
|
|
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
|
|
Update driver version to 8.3.22
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Update Copyright Dates
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
FC Discovery fixes
- In lpfc_sli4_bpl2sgl byte swapping the SGL in word2.
- In lpfc_sli4_iocb2wqe byteswap the data for CMD_GEN_REQUEST64_CR type WQE.
- In lpfc_sli4_seq_abort_acc do not set the oxid into the iocb's xritag field.
- In lpfc_sli4_seq_abort_acc check the return value of lpfc_sli_issue_iocb.
- Inprove messages in this area.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Periodically poll adapter registers to detect pci adapter failure
(reads return -1). On failure, take port offline, set error indicators
and wake up worker threads. Threads will take adapter offline.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
T10-DIF corrections
- Add selective reset jump table entry
- Split T10-DIF BDEs that cross 4K boundary
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
- Add new Queue Create Mailbox version support
- Make lpfc_bsg_wake_mbox_wait routine check the mailboxes job reference before
using it.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6
* 'trivial' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6: (25 commits)
video: change to new flag variable
scsi: change to new flag variable
rtc: change to new flag variable
rapidio: change to new flag variable
pps: change to new flag variable
net: change to new flag variable
misc: change to new flag variable
message: change to new flag variable
memstick: change to new flag variable
isdn: change to new flag variable
ieee802154: change to new flag variable
ide: change to new flag variable
hwmon: change to new flag variable
dma: change to new flag variable
char: change to new flag variable
fs: change to new flag variable
xtensa: change to new flag variable
um: change to new flag variables
s390: change to new flag variable
mips: change to new flag variable
...
Fix up trivial conflict in drivers/hwmon/Makefile
|
|
Replace EXTRA_CFLAGS with ccflags-y.
Signed-off-by: matt mooney <mfm@muteddisk.com>
Acked-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
|
|
Instead of blocking the entire host when the port's
queueing limit is hit, we should only block the port's
target. This will allow IO to other ports to execute.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
If the port takes a while to transition we could exhaust
the retries when using DID_TRANSPORT_DISRUPTED. For this
case we do not want to use any of the cmd's
retries, because if the command was running then when
it got failed the retry counter was already incremented.
And if this is the first time we are seeing the command,
(it got queued because it slipped through during the race)
then it should not have its retries incremented. The
fc class will decide the correct handling later.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
- Add the driver debugfs framework for supporting debugfs read and write
operations, and iDiag command structure.
- Add read and write to SLI4 device PCI config space registers.
- Add the driver support of debugfs PCI config space register bits set/clear
methods to the provided bitmask.
- Add iDiag driver support for SLI4 device queue diagnostic.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
- Make link speed not supported by port message an error message.
- Add support for new SLI failure codes add sysfs parameter to reflect the
security setting and current state.
- Add all lpfc module parameters to the /sys/modules/lpfc/parameters directory.
[jejb: fix up compile failure]
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
FC Discovery changes
- Treat received PLOGI while logged in as a relogin (unregister and reregister).
- Added a timer to delay Nport discovery when clean bit is cleared and Fabric
portname/nodename/FCID is changed.
- Invalidate Port's DID when receiving PLOGI from p2p port with CONFIG_PORT
mailbox command.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
RRQ Implementation fixes
- Added checks to prevent a call to findnode_did in clr_active_rrq
- Added the del_sync_timer call for the rrq_tmr to the stop_hba_timers routine.
- Added a check in __lpfc_set_active_rrq for the driver unloading to prevent
adding an rrq when the driver is being removed.
- Add code to scsi_iocb_cmpl to check for the remote stop and add the rrq.
- Added the same check to els retry.
- Added code to compare the source did in the els rrq to the vports did and
chose the right exchange ID.
- Initialize the start_cmd pointer to indicate when we have looped through
all of the scsi buffers.
- Remove the need for the lock around the clearing of the active bit in the
rrq.
- Added code to clean the els and fcp xri aborted list and remove the all of
the RRQs for a deleted vport.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Critical Errors:
- Correctly handle non-zero return lpfc_workq_post_event and return ENOMEM
- Save the irq level when locking the host_lock in lpfc_findnode_did
Bug Fixes:
- Adjust payload_length and request_length for sli4_config mailbox commands.
- Add the freed sgl/XRI to the tail of the list rather than to the head.
- Set the FC_VPORT_NEEDS_INIT_VPI on vport deletes and check it before
issuing a fdisc on an els retry.
- Only call lpfc_hba_init_link() if phba->cfg_suppress_link_up
is LPFC_INITIALIZE_LINK.
- Add support for SLI-4 Performance Hints
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
Documentation/trace/events.txt: Remove obsolete sched_signal_send.
writeback: fix global_dirty_limits comment runtime -> real-time
ppc: fix comment typo singal -> signal
drivers: fix comment typo diable -> disable.
m68k: fix comment typo diable -> disable.
wireless: comment typo fix diable -> disable.
media: comment typo fix diable -> disable.
remove doc for obsolete dynamic-printk kernel-parameter
remove extraneous 'is' from Documentation/iostats.txt
Fix spelling milisec -> ms in snd_ps3 module parameter description
Fix spelling mistakes in comments
Revert conflicting V4L changes
i7core_edac: fix typos in comments
mm/rmap.c: fix comment
sound, ca0106: Fix assignment to 'channel'.
hrtimer: fix a typo in comment
init/Kconfig: fix typo
anon_inodes: fix wrong function name in comment
fix comment typos concerning "consistent"
poll: fix a typo in comment
...
Fix up trivial conflicts in:
- drivers/net/wireless/iwlwifi/iwl-core.c (moved to iwl-legacy.c)
- fs/ext4/ext4.h
Also fix missed 'diabled' typo in drivers/net/bnx2x/bnx2x.h while at it.
|
|
according to checkstack the lpfc_fc_frame_check occupies the first
place in stack usage:
make checkstack
objdump -d vmlinux $(find . -name '*.ko') | \
perl /root/rpmbuild/BUILD/kernel-2.6.32/linux-2.6.32.x86_64/scripts/checkstack.pl x86_64
0x000013f4 lpfc_fc_frame_check [lpfc]: 1936
...
This change makes the rctl_names static, thus not on stack.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
