| Age | Commit message (Collapse) | Author |
|---|
|
commit c0a5f4a05af588a0f9951f8d24e2564b09501918 upstream.
The reset date of the ST Micro version of PL031 is 2000-01-01. The
correct weekday for 2000-01-01 is saturday, but pl031 is initialized to
sunday. This may lead to alarm malfunction, so configure the correct
wday if RTC_DR indicates reset.
Signed-off-by: Rajkumar Kasirajan <rajkumar.kasirajan@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Mattias Wallin <mattias.wallin@stericsson.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2f3972168353d355854d6381f1f360ce83b723e5 upstream.
The ST variants of the PL031 all require bit 26 in the control register
to be set before they work properly. Discovered this when testing on
the Nomadik board where it would suprisingly just stand still.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Cc: Alessandro Rubini <rubini@unipv.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4a649903f91232d02284d53724b0a45728111767 upstream.
Richard Weinberger noticed that on some RTC hardware that
doesn't support UIE mode, due to coarse granular alarms
(like 1minute resolution), the current virtualized RTC
support doesn't properly error out when UIE is enabled.
Instead the current code queues an alarm for the next second,
but it won't fire until up to a miniute later.
This patch provides a generic way to flag this sort of hardware
and fixes the issue on the mpc5121 where Richard noticed the
problem.
Reported-by: Richard Weinberger <richard@nod.at>
Tested-by: Richard Weinberger <richard@nod.at>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 41c7f7424259ff11009449f87c95656f69f9b186 upstream.
Currently, the RTC code does not disable the alarm in the hardware.
This means that after a sequence such as the one below (the files are in the
RTC sysfs), the box will boot up after 2 minutes even though we've
asked for the alarm to be turned off.
# echo $((`cat since_epoch`)+120) > wakealarm
# echo 0 > wakealarm
# poweroff
Fix this by disabling the alarm when there are no timers to run.
The original version of this patch was reverted. This version
disables the irq directly instead of setting a disabled timer
in the future.
Cc: John Stultz <john.stultz@linaro.org>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
[Merged in the second revision from Rabin]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If probing the RTC didn't succeed due to failed RTC register access, the
RTC device will be unregistered. Then, when removing the module
r9701_remove() causes a kernel crash while trying to unregister a not
registered RTC device. Fix this by doing RTC register access test before
RTC device registration.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Instead of computing virtual address with AT91_VA_BASE_SYS, use the
appropriate ioremap() call on the driver "memory" resource.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
This reverts commit 42874759d7494648e42e6e0465fc9c4f3752bba4.
This wasn't tested as a stand-alone patch, and it has build errors
without the following patches applied:
drivers/rtc/rtc-sa1100.c: In function 'sa1100_rtc_set_alarm':
drivers/rtc/rtc-sa1100.c:208: error: 'now' undeclared (first use in this function)
drivers/rtc/rtc-sa1100.c:208: error: (Each undeclared identifier is reported only once
drivers/rtc/rtc-sa1100.c:208: error: for each function it appears in.)
drivers/rtc/rtc-sa1100.c:210: error: incompatible type for argument 3 of 'rtc_next_alarm_time'
drivers/rtc/rtc-sa1100.c:211: error: 'time' undeclared (first use in this function)
So it too gets reverted to bring us back to a working point.
|
|
This reverts commit 7cea00657dd4daef66ad95e976d5d67ed94cb97e.
The sa1100 cleanups fatally broke the SA1100 RTC driver - the first
hint that something is wrong are these compiler warnings:
drivers/rtc/rtc-sa1100.c:42:1: warning: "RCNR" redefined
In file included from arch/arm/mach-sa1100/include/mach/hardware.h:73,
from drivers/rtc/rtc-sa1100.c:35:
arch/arm/mach-sa1100/include/mach/SA-1100.h:877:1: warning: this is the location of the previous definition
drivers/rtc/rtc-sa1100.c:43:1: warning: "RTAR" redefined
arch/arm/mach-sa1100/include/mach/SA-1100.h:876:1: warning: this is the location of the previous definition
drivers/rtc/rtc-sa1100.c:44:1: warning: "RTSR" redefined
arch/arm/mach-sa1100/include/mach/SA-1100.h:879:1: warning: this is the location of the previous definition
drivers/rtc/rtc-sa1100.c:45:1: warning: "RTTR" redefined
arch/arm/mach-sa1100/include/mach/SA-1100.h:878:1: warning: this is the location of the previous definition
drivers/rtc/rtc-sa1100.c:47:1: warning: "RTSR_HZE" redefined
arch/arm/mach-sa1100/include/mach/SA-1100.h:891:1: warning: this is the location of the previous definition
drivers/rtc/rtc-sa1100.c:48:1: warning: "RTSR_ALE" redefined
arch/arm/mach-sa1100/include/mach/SA-1100.h:890:1: warning: this is the location of the previous definition
drivers/rtc/rtc-sa1100.c:49:1: warning: "RTSR_HZ" redefined
arch/arm/mach-sa1100/include/mach/SA-1100.h:889:1: warning: this is the location of the previous definition
drivers/rtc/rtc-sa1100.c:50:1: warning: "RTSR_AL" redefined
arch/arm/mach-sa1100/include/mach/SA-1100.h:888:1: warning: this is the location of the previous definition
and the second problem, which is far more severe, are the different
register layouts, resulting in the wrong registers being read on
SA11x0 platforms. This patch adds:
#define RCNR 0x00 /* RTC Count Register */
#define RTAR 0x04 /* RTC Alarm Register */
#define RTSR 0x08 /* RTC Status Register */
#define RTTR 0x0c /* RTC Timer Trim Register */
but the SA11x0 registers are:
#define RTAR __REG(0x90010000) /* RTC Alarm Reg. */
#define RCNR __REG(0x90010004) /* RTC CouNt Reg. */
#define RTTR __REG(0x90010008) /* RTC Trim Reg. */
#define RTSR __REG(0x90010010) /* RTC Status Reg. */
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (59 commits)
rtc: max8925: Add function to work as wakeup source
mfd: Add pm ops to max8925
mfd: Convert aat2870 to dev_pm_ops
mfd: Still check other interrupts if we get a wm831x touchscreen IRQ
mfd: Introduce missing kfree in 88pm860x probe routine
mfd: Add S5M series configuration
mfd: Add s5m series irq driver
mfd: Add S5M core driver
mfd: Improve mc13xxx dt binding document
mfd: Fix stmpe section mismatch
mfd: Fix stmpe build warning
mfd: Fix STMPE I2c build failure
mfd: Constify aat2870-core i2c_device_id table
gpio: Add support for stmpe variant 801
mfd: Add support for stmpe variant 801
mfd: Add support for stmpe variant 610
mfd: Add support for STMPE SPI interface
mfd: Separate out STMPE controller and interface specific code
misc: Remove max8997-muic sysfs attributes
mfd: Remove unused wm831x_irq_data_to_mask_reg()
...
Fix up trivial conflict in drivers/leds/Kconfig due to addition of
LEDS_MAX8997 and LEDS_TCA6507 next to each other.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/intel config: Fix the APB_TIMER selection
x86/mrst: Add additional debug prints for pb_keys
x86/intel config: Revamp configuration to allow for Moorestown and Medfield
x86/intel/scu/ipc: Match the changes in the x86 configuration
x86/apb: Fix configuration constraints
x86: Fix INTEL_MID silly
x86/Kconfig: Cyclone-timer depends on x86-summit
x86: Reduce clock calibration time during slave cpu startup
x86/config: Revamp configuration for MID devices
x86/sfi: Kill the IRQ as id hack
|
|
* 'unicore32' of git://github.com/gxt/linux:
rtc-puv3: solve section mismatch in rtc-puv3.c
rtc-puv3: using module_platform_driver()
i2c-puv3: using module_platform_driver()
rtc-puv3: irq: remove IRQF_DISABLED
unicore32: Remove IRQF_DISABLED
unicore32: Use set_current_blocked()
unicore32: add ioremap_nocache definition
unicore32: delete specified xlate_dev_mem_ptr
of: add include asm/setup.h in drivers/of/fdt.c
unicore32: standardize /proc/iomem "Kernel code" name
|
|
Commit f44f7f96a20a ("RTC: Initialize kernel state from RTC") introduced a
potential infinite loop. If an alarm time contains a wildcard month and
an invalid day (> 31), or a wildcard year and an invalid month (>= 12),
the loop searching for the next matching date will never terminate. Treat
the invalid values as wildcards.
Fixes <http://bugs.debian.org/646429>, <http://bugs.debian.org/653331>
Reported-by: leo weppelman <leoweppelman@googlemail.com>
Reported-by: "P. van Gaans" <mailme667@yahoo.co.uk>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Jonathan Nieder <jrnieder@gmail.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <john.stultz@linaro.org>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add the DT support for the TI rtc-twl present in the twl4030 and twl6030
devices.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In ancient times it was necessary to manually initialize the bus field of
an spi_driver to spi_bus_type. These days this is done in
spi_driver_register(), so we can drop the manual assignment.
The patch was generated using the following coccinelle semantic patch:
// <smpl>
@@
identifier _driver;
@@
struct spi_driver _driver = {
.driver = {
- .bus = &spi_bus_type,
},
};
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch converts the drivers in drivers/rtc/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Ben Dooks <ben@simtec.co.uk>
Cc: John Stultz <john.stultz@linaro.org>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Marginally less code and eliminate the possibility of memory leaks.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Due to changes in the RTC core the period interrupt is now unused so
delete the code managing it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The rtc_calibration attribute allows user-space to get and set the
AB8500's RtcCalibration register. The AB8500 will then use the value in
this register to compensate for RTC drift every 60 seconds.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Mark Godfrey <mark.godfrey@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The resolution of msleep is related to HZ, so with HZ set to 100 any
msleep of less than 10ms will become ~10ms. This is not what we want.
Use the hrtimer-based usleep_range() and allow for some slack in the
non-critical path so we have more control of what is happening here.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Jonas Aaberg <jonas.aberg@stericsson.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Set can_wake flag so wakealarm property is visible in sysfs.
Signed-off-by: Andrew Lynn <andrew.lynn@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We want this driver to be able to wake up the system.
Signed-off-by: Robert Marklund <robert.marklund@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix alarm IRQ handling, make the alarm one-shot. Cleanup black magick
with a validation of already validated time data.
Add ability to wake the system with alarm.
[akpm@linux-foundation.org: fix CONFIG_PM=n build]
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
There is no way to track year in the i.MX1 RTC: Days Counter register is
9-bit wide only. Attempt to save date after 1970-01-01 plus 512 days
causes endless loop in mxc_rtc_set_mmss(). Fix this by resetting year to
1970.
[akpm@linux-foundation.org: use conventional comment layout]
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix writing to NVRAM bank 2 in rtc-cmos driver. It never worked since its
introduction in 2.6.28 because of a typo.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The patch renames puv3_rtcdrv to puv3_rtc_driver, so that modpost will know
that this is simply a list of pointers to driver functions, in which case
the section mismatch is OK. (Thanks Michal Marek)
Cc: Axel Lin <axel.lin@gmail.com>
Cc: Michal Marek <mmarek@suse.cz>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: rtc-linux@googlegroups.com
Signed-off-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
--
Section mismatch warning information:
WARNING: drivers/rtc/built-in.o(.data+0x90): Section mismatch in
reference from the variable puv3_rtcdrv to the
function .devinit.text:puv3_rtc_probe()
The variable puv3_rtcdrv references
the function __devinit puv3_rtc_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the
variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one,
*_console
WARNING: drivers/rtc/built-in.o(.data+0x94): Section mismatch in
reference from the variable puv3_rtcdrv to the
function .devexit.text:puv3_rtc_remove()
The variable puv3_rtcdrv references
the function __devexit puv3_rtc_remove()
If the reference is valid then annotate the
variable with __exit* (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one,
*_console
WARNING: drivers/built-in.o(.data+0x6c04): Section mismatch in reference
from the variable puv3_rtcdrv to the
function .devinit.text:puv3_rtc_probe()
The variable puv3_rtcdrv references
the function __devinit puv3_rtc_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the
variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one,
*_console
WARNING: drivers/built-in.o(.data+0x6c08): Section mismatch in reference
from the variable puv3_rtcdrv to the
function .devexit.text:puv3_rtc_remove()
The variable puv3_rtcdrv references
the function __devexit puv3_rtc_remove()
If the reference is valid then annotate the
variable with __exit* (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one,
*_console
WARNING: vmlinux.o(.data+0x1126c): Section mismatch in reference from
the variable puv3_rtcdrv to the function .devinit.text:puv3_rtc_probe()
The variable puv3_rtcdrv references
the function __devinit puv3_rtc_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the
variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one,
*_console
WARNING: vmlinux.o(.data+0x11270): Section mismatch in reference from
the variable puv3_rtcdrv to the function .devexit.text:puv3_rtc_remove()
The variable puv3_rtcdrv references
the function __devexit puv3_rtc_remove()
If the reference is valid then annotate the
variable with __exit* (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one,
*_console
|
|
This patch converts the driver to use the module_platform_driver()
macro which makes the code smaller and a bit simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
|
|
This flag is deprecated, so is removed now.
Signed-off-by: Yong Zhang <yong.zhang@gmail.com>
Signed-off-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
|
|
Driver specific changes
Again, a lot of platforms have changes in here: pxa, samsung, omap,
at91, imx, ...
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits)
ARM: sa1100: clean up of the clock support
ARM: pxa: add dummy clock for sa1100-rtc
RTC: sa1100: support sa1100, pxa and mmp soc families
RTC: sa1100: remove redundant code of setting alarm
RTC: sa1100: Clean out ost register
Input: zylonite-wm97xx - replace IRQ_GPIO() with gpio_to_irq()
pcmcia: pxa: replace IRQ_GPIO() with gpio_to_irq()
ARM: EXYNOS: Modified files for SPI consolidation work
ARM: S5P64X0: Enable SDHCI support
ARM: S5P64X0: Add lookup of sdhci-s3c clocks using generic names
ARM: S5P64X0: Add HSMMC setup for host Controller
ARM: EXYNOS: Add USB OHCI support to ORIGEN board
USB: Add Samsung Exynos OHCI diver
ARM: EXYNOS: Add USB OHCI support to SMDKV310 board
ARM: EXYNOS: Add USB OHCI device
net: macb: fix build break with !CONFIG_OF
i2c: tegra: Support DVC controller in device tree
i2c: tegra: Add __devinit/exit to probe/remove
net/at91_ether: use gpio_is_valid for phy IRQ line
ARM: at91/net: add macb ethernet controller in 9g45/9g20 DT
...
|
|
Device tree conversions for samsung and tegra
Both platforms had some initial device tree support, but this adds
much more to actually make it usable.
* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (45 commits)
ARM: dts: Add intial dts file for EXYNOS4210 SoC, SMDKV310 and ORIGEN
ARM: EXYNOS: Add Exynos4 device tree enabled board file
rtc: rtc-s3c: Add device tree support
input: samsung-keypad: Add device tree support
ARM: S5PV210: Modify platform data for pl330 driver
ARM: S5PC100: Modify platform data for pl330 driver
ARM: S5P64x0: Modify platform data for pl330 driver
ARM: EXYNOS: Add a alias for pdma clocks
ARM: EXYNOS: Limit usage of pl330 device instance to non-dt build
ARM: SAMSUNG: Add device tree support for pl330 dma engine wrappers
DMA: PL330: Add device tree support
ARM: EXYNOS: Modify platform data for pl330 driver
DMA: PL330: Infer transfer direction from transfer request instead of platform data
DMA: PL330: move filter function into driver
serial: samsung: Fix build for non-Exynos4210 devices
serial: samsung: add device tree support
serial: samsung: merge probe() function from all SoC specific extensions
serial: samsung: merge all SoC specific port reset functions
ARM: SAMSUNG: register uart clocks to clock lookup list
serial: samsung: remove all uses of get_clksrc and set_clksrc
...
Fix up fairly trivial conflicts in arch/arm/mach-s3c2440/clock.c and
drivers/tty/serial/Kconfig both due to just adding code close to
changes.
|
|
Cleanups on various subarchitectures
Cleanup patches for various ARM platforms and some of their associated
drivers, the bulk of these is for mach-91.
Arnd ended up pulling in the restart branch from Russell in order to
fix up some simple but annoying merge conflicts.
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (44 commits)
arm/at91: fix build of stamp9g20
ARM: u300: delete memory.h
MAINTAINERS: add maintainer entry for Picochip picoxcell
ARM: picoxcell: move io mappings to common.c
ARM: picoxcell: don't reserve irq_descs
ARM: picoxcell: remove mach/memory.h
ARM: at91: delete the pcontrol_g20_defconfig
arm/tegra: Remove code that's ifndef CONFIG_ARM_GIC
arm/tegra: remove unused defines
arm/tegra: fix variable formatting in makefile
ARM: davinci: vpif: move code to driver core header from platform
ARM: at91/gpio: fix display of number of irq setuped
ARM: at91/gpio: drop PIN_BASE
ARM: at91/udc: use gpio_is_valid to check the gpio
ARM: at91/ohci: use gpio_is_valid to check the gpio
ARM: at91/nand: use gpio_is_valid to check the gpio
ARM: at91/mmc: use gpio_is_valid to check the gpio
ARM: at91/ide: use gpio_is_valid to check the gpio
ARM: at91/pata: use gpio_is_valid to check the gpio
ARM: at91/soc: use gpio_is_valid to check the gpio
...
|
|
Conflicts:
arch/arm/mach-mxs/include/mach/common.h
Pull in previous samsung conflict merges and do a trivial
merge of an mxs double-add conflict.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This moves all the header files related to the abx500 family into
a common include directory below mfd. From now on we place any
subchip header in that directory. Headers previously in e.g.
<linux/mfd/ab8500/gpio.h> get prefixed and are now e.g.
<linux/mfd/abx500/ab8500-gpio.h>. The top-level abstract interface
remains in <linux/mfd/abx500.h>.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Conflicts:
arch/arm/mach-exynos/common.c
The common.c file gets changes from rmk/stable-devel (part of
next/cleanup), rmk/restart, samsung/dt and follow-on branches
from the samsung tree.
Pulling it all together here hopefully avoids having to do
even more conflicting merge changesets in this one file. What
a mess!
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Conflicts:
arch/arm/mach-exynos/Makefile
arch/arm/mach-exynos/cpu.c -> common.c
arch/arm/mach-exynos/include/mach/entry-macro.S
arch/arm/mach-exynos/init.c -> common.c
arch/arm/mach-s5p64x0/init.c -> common.c
arch/arm/mach-s5pv210/init.c -> common.c
Multiple files were moved into common.c files in the rmk/for-linus
branch, so this moves over the samsung/dt changes to the new
files.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Conflicts:
arch/arm/mach-at91/at91cap9.c
arch/arm/mach-at91/at91sam9260.c
arch/arm/mach-at91/at91sam9261.c
arch/arm/mach-at91/at91sam9263.c
arch/arm/mach-at91/at91sam9g45.c
arch/arm/mach-at91/at91sam9rl.c
arch/arm/mach-exynos/cpu.c
arch/arm/mach-shmobile/board-kota2.c
This resolves a bunch of conflicts between the arm-soc tree
and changes from the arm tree that have gone upstream.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm
* 'amba-modalias' of git://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm:
sound: aaci: Enable module alias autogeneration for AMBA drivers
watchdog: sp805: Enable module alias autogeneration for AMBA drivers
fbdev: amba: Enable module alias autogeneration for AMBA drivers
serial: pl011: Enable module alias autogeneration for AMBA drivers
serial: pl010: Enable module alias autogeneration for AMBA drivers
spi: pl022: Enable module alias autogeneration for AMBA drivers
rtc: pl031: Enable module alias autogeneration for AMBA drivers
rtc: pl030: Enable module alias autogeneration for AMBA drivers
mmc: mmci: Enable module alias autogeneration for AMBA drivers
input: ambakmi: Enable module alias autogeneration for AMBA drivers
gpio: pl061: Enable module alias autogeneration for AMBA drivers
dmaengine: pl330: Enable module alias autogeneration for AMBA drivers
dmaengine: pl08x: Enable module alias autogeneration for AMBA drivers
hwrng: nomadik: Enable module alias autogeneration for AMBA drivers
ARM: amba: Auto-generate AMBA driver module aliases during modpost
ARM: amba: Move definition of struct amba_id to mod_devicetable.h
|
|
This reverts commit 93b2ec0128c431148b216b8f7337c1a52131ef03.
The call to "schedule_work()" in rtc_initialize_alarm() happens too
early, and can cause oopses at bootup
Neil Brown explains why we do it:
"If you set an alarm in the future, then shutdown and boot again after
that time, then you will end up with a timer_queue node which is in
the past.
When this happens the queue gets stuck. That entry-in-the-past won't
get removed until and interrupt happens and an interrupt won't happen
because the RTC only triggers an interrupt when the alarm is "now".
So you'll find that e.g. "hwclock" will always tell you that
'select' timed out.
So we force the interrupt work to happen at the start just in case."
and has a patch that convert it to do things in-process rather than with
the worker thread, but right now it's too late to play around with this,
so we just revert the patch that caused problems for now.
Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Requested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Requested-by: John Stultz <john.stultz@linaro.org>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This reverts commit c0afabd3d553c521e003779c127143ffde55a16f.
It causes failures on Toshiba laptops - instead of disabling the alarm,
it actually seems to enable it on the affected laptops, resulting in
(for example) the laptop powering on automatically five minutes after
shutdown.
There's a patch for it that appears to work for at least some people,
but it's too late to play around with this, so revert for now and try
again in the next merge window.
See for example
http://bugs.debian.org/652869
Reported-and-bisected-by: Andreas Friedrich <afrie@gmx.net> (Toshiba Tecra)
Reported-by: Antonio-M. Corbi Bellot <antonio.corbi@ua.es> (Toshiba Portege R500)
Reported-by: Marco Santos <marco.santos@waynext.com> (Toshiba Portege Z830)
Reported-by: Christophe Vu-Brugier <cvubrugier@yahoo.fr> (Toshiba Portege R830)
Cc: Jonathan Nieder <jrnieder@gmail.com>
Requested-by: John Stultz <john.stultz@linaro.org>
Cc: stable@kernel.org # for the versions that applied this
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* drivers/rtc-sa1100:
ARM: sa1100: clean up of the clock support
ARM: pxa: add dummy clock for sa1100-rtc
RTC: sa1100: support sa1100, pxa and mmp soc families
RTC: sa1100: remove redundant code of setting alarm
RTC: sa1100: Clean out ost register
Conflicts:
arch/arm/mach-pxa/pxa25x.c
arch/arm/mach-pxa/pxa27x.c
|
|
Since the regmap of rtc on sa1100, pxa and mmp Marvell soc families are
almost the same, so re-arch the rtc-sa1100 to support them.
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
In rtc generic interface of setting alarm, it will check the alarm time
value valid or not, so rtc_periodic_alarm is redundant, remove it.
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
These registers are used in old ioctl of UIE and PIE, now they are
emulated by rtc generic code of hrtimer, so it can be removed.
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add device tree based discovery support for Samsung's rtc controller.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
time/clocksource: Fix kernel-doc warnings
rtc: m41t80: Workaround broken alarm functionality
rtc: Expire alarms after the time is set.
|
|
|
|
This sets all up the other bits that need to be INTEL_MID
specific rather than Moorestown specific.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Link: http://lkml.kernel.org/r/20111217174318.7207.91543.stgit@bob.linux.org.uk
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
|
