aboutsummaryrefslogtreecommitdiff
path: root/drivers/pcmcia/ti113x.h
AgeCommit message (Collapse)Author
2006-06-30[PATCH] pcmcia: TI PCIxx12 CardBus controller supportAlex Williamson
The patch below adds support for the TI PCIxx12 CardBus controllers. This seems to be sufficient to detect the cardbus bridge on an HP nc6320 and works with an orinoco wifi card. Signed-off-by: Alex Williamson <alex.williamson@hp.com> Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
2006-03-31[PATCH] pcmcia: remove include of config.hDominik Brodowski
Remove the inclusion of include/config.h as it isn't needed any longer. Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
2006-01-05[PATCH] yenta: make bridge specific init code configurableDaniel Ritz
Make the bridge specific initialization code config options depending on CONFIG_EMBEDDED. Config options for TI/EnE, Toshiba, Ricoh and O2Micro are available. Disabling all of the specific tweaks cuts off more than half of yenta_socket.ko. Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch> Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
2005-10-08[PATCH] yenta: fix build if YENTA && !CARDBUSDavid Vrabel
(struct pcmcia_socket).tune_bridge only exists if CONFIG_CARDBUS is set but building yenta_socket without CardBus is valid. Signed-off-by: David Vrabel <dvrabel@arcom.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-09-26[PATCH] yenta: add support for more TI bridgesDaniel Ritz
Support some more TI cardbus bridges. most of them are multifunction devices which adds 1394 controllers, smartcard readers etc. this could also help with the various problems with the XX21 controllers seen on the linux-pcmcia list. Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch> Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
2005-09-26[PATCH] yenta: auto-tune EnE bridges for CardBus cardsDaniel Ritz
Echo Audio cardbus products are known to be incompatible with EnE bridges. in order to maybe solve the problem a EnE specific test bit has to be set, another cleared...but other setups have a good chance to break when just forcing the bits. so do the whole thingy automatically. The patch adds a hook in cb_alloc() that allows special tuning for the different chipsets. for ene just match the Echo products and set/clear the test bits, defaults to do the same thing as w/o the patch to not break working setups. Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch> Cc: Linus Torvalds <torvalds@osdl.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
2005-07-07[PATCH] yenta: don't depend on CardBusDominik Brodowski
As a follow-up, we can allow the yenta-driver to be limited to PCMCIA operation. Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-06-23[PATCH] yenta TI: turn off interrupts during card power-on #2Daniel Ritz
- make boot-up card recognition more reliable (ie. redo interrogation always if there is no valid 'card inserted' state) (and yes, i saw it happening on an o2micro controller that both CB_CBARD and CB_16BITCARD bits were set at the same time) - also redo interrogation before probing the ISA interrupts. it's safer to do the probing with the socket in a clean state. - make card insert detect more reliable. yenta_get_status() now returns SS_PENDING as long as the card is not completley inserted and one of the voltage bits is set. also !CB_CBARD doesn't mean CB_16BITCARD. there is CB_NOTACARD as well, so make an explicit check for CB_16BITCARD. - for TI bridges: disable IRQs during power-on. in all-serial and tied interrupt mode the interrupts are always disabled for single-slot controllers. for two-slot contollers the disabling is only done when the other slot is empty. to force disabling there is a new module parameter now: pwr_irqs_off=Y (which is a regression for working setups. that's why it's an option, only use when required) - modparm to disable ISA interrupt probing (isa_probe, defaults to on) - remove unneeded code/cleanups (ie. merge yenta_events() into yenta_interrupts()) Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-05-05[PATCH] pcmcia: yenta TI: align irq of func1 to func0 if INTRTIE is setDaniel Ritz
Make sure that if the INTRTIE bit is set both functions of the cardbus bridge use the same IRQ before doing any probing... [ yes i hate the TI bridges for the fact that they are very flexible so that so many BIOS vendors get it wrong. ] Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch> Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-04-16Linux-2.6.12-rc2v2.6.12-rc2Linus Torvalds
Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!