aboutsummaryrefslogtreecommitdiff
path: root/drivers/net
AgeCommit message (Collapse)Author
2010-08-03pcmcia: do not use io_req_t when calling pcmcia_request_io()Dominik Brodowski
Instead of io_req_t, drivers are now requested to fill out struct pcmcia_device *p_dev->resource[0,1] for up to two ioport ranges. After a call to pcmcia_request_io(), the ports found there are reserved, after calling pcmcia_request_configuration(), they may be used. CC: netdev@vger.kernel.org CC: linux-wireless@vger.kernel.org CC: linux-ide@vger.kernel.org CC: linux-usb@vger.kernel.org CC: laforge@gnumonks.org CC: linux-mtd@lists.infradead.org CC: alsa-devel@alsa-project.org CC: linux-serial@vger.kernel.org CC: Michael Buesch <mb@bu3sch.de> Acked-by: Marcel Holtmann <marcel@holtmann.org> (for drivers/bluetooth/) Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
2010-08-03pcmcia: do not use io_req_t after call to pcmcia_request_io()Dominik Brodowski
After pcmcia_request_io(), do not make use of the values stored in io_req_t, but instead use those found in struct pcmcia_device->resource[]. CC: netdev@vger.kernel.org CC: linux-wireless@vger.kernel.org CC: linux-ide@vger.kernel.org CC: linux-usb@vger.kernel.org CC: laforge@gnumonks.org CC: linux-mtd@lists.infradead.org CC: alsa-devel@alsa-project.org CC: linux-serial@vger.kernel.org Acked-by: Marcel Holtmann <marcel@holtmann.org> (for drivers/bluetooth/) Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
2010-08-03pcmcia: use pcmica_{read,write}_config_byteDominik Brodowski
Use pcmcia_read_config_byte and pcmcia_write_config_byte instead of pcmcia_access_configuration_register. CC: netdev@vger.kernel.org CC: linux-wireless@vger.kernel.org CC: linux-serial@vger.kernel.org CC: Michael Buesch <mb@bu3sch.de> Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
2010-07-30pcmcia: remove cs_types.hDominik Brodowski
Remove cs_types.h which is no longer needed: Most definitions aren't used at all, a few can be made away with, and two remaining definitions (typedefs, unfortunatley) may be moved to more specific places. CC: linux-ide@vger.kernel.org CC: linux-usb@vger.kernel.org CC: laforge@gnumonks.org CC: linux-mtd@lists.infradead.org CC: alsa-devel@alsa-project.org CC: linux-serial@vger.kernel.org Acked-by: Marcel Holtmann <marcel@holtmann.org> (for drivers/bluetooth/) Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
2010-07-20Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (24 commits) bridge: Partially disable netpoll support tcp: fix crash in tcp_xmit_retransmit_queue IPv6: fix CoA check in RH2 input handler (mip6_rthdr_input()) ibmveth: lost IRQ while closing/opening device leads to service loss rt2x00: Fix lockdep warning in rt2x00lib_probe_dev() vhost: avoid pr_err on condition guest can trigger ipmr: Don't leak memory if fib lookup fails. vhost-net: avoid flush under lock net: fix problem in reading sock TX queue net/core: neighbour update Oops net: skb_tx_hash() fix relative to skb_orphan_try() rfs: call sock_rps_record_flow() in tcp_splice_read() xfrm: do not assume that template resolving always returns xfrms hostap_pci: set dev->base_addr during probe axnet_cs: use spin_lock_irqsave in ax_interrupt dsa: Fix Kconfig dependencies. act_nat: not all of the ICMP packets need an IP header payload r8169: incorrect identifier for a 8168dp Phonet: fix skb leak in pipe endpoint accept() Bluetooth: Update sec_level/auth_type for already existing connections ...
2010-07-19Merge branch 'master' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
2010-07-16ibmveth: lost IRQ while closing/opening device leads to service lossRobert Jennings
The order of freeing the IRQ and freeing the device in firmware in ibmveth_close can cause the adapter to become unusable after a subsequent ibmveth_open. Only a reboot of the OS will make the network device usable again. This is seen when cycling the adapter up and down while there is network activity. There is a window where an IRQ will be left unserviced (H_EOI will not be called). The solution is to make a VIO_IRQ_DISABLE h_call, free the device with firmware, and then call free_irq. Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-16rt2x00: Fix lockdep warning in rt2x00lib_probe_dev()Stephen Boyd
The rt2x00dev->intf_work workqueue is never initialized when a driver is probed for a non-existent device (in this case rt2500usb). On such a path we call rt2x00lib_remove_dev() to free any resources initialized during the probe before we use INIT_WORK to initialize the workqueue. This causes lockdep to get confused since the lock used in the workqueue hasn't been initialized yet but is now being acquired during cancel_work_sync() called by rt2x00lib_remove_dev(). Fix this by initializing the workqueue first before we attempt to probe the device. This should make lockdep happy and avoid breaking any assumptions about how the library cleans up after a probe fails. phy0 -> rt2x00lib_probe_dev: Error - Failed to allocate device. INFO: trying to register non-static key. the code is fine but needs lockdep annotation. turning off the locking correctness validator. Pid: 2027, comm: modprobe Not tainted 2.6.35-rc5+ #60 Call Trace: [<ffffffff8105fe59>] register_lock_class+0x152/0x31f [<ffffffff81344a00>] ? usb_control_msg+0xd5/0x111 [<ffffffff81061bde>] __lock_acquire+0xce/0xcf4 [<ffffffff8105f6fd>] ? trace_hardirqs_off+0xd/0xf [<ffffffff81492aef>] ? _raw_spin_unlock_irqrestore+0x33/0x41 [<ffffffff810628d5>] lock_acquire+0xd1/0xf7 [<ffffffff8104f037>] ? __cancel_work_timer+0x99/0x17e [<ffffffff8104f06e>] __cancel_work_timer+0xd0/0x17e [<ffffffff8104f037>] ? __cancel_work_timer+0x99/0x17e [<ffffffff8104f136>] cancel_work_sync+0xb/0xd [<ffffffffa0096675>] rt2x00lib_remove_dev+0x25/0xb0 [rt2x00lib] [<ffffffffa0096bf7>] rt2x00lib_probe_dev+0x380/0x3ed [rt2x00lib] [<ffffffff811d78a7>] ? __raw_spin_lock_init+0x31/0x52 [<ffffffffa00bbd2c>] ? T.676+0xe/0x10 [rt2x00usb] [<ffffffffa00bbe4f>] rt2x00usb_probe+0x121/0x15e [rt2x00usb] [<ffffffff813468bd>] usb_probe_interface+0x151/0x19e [<ffffffff812ea08e>] driver_probe_device+0xa7/0x136 [<ffffffff812ea167>] __driver_attach+0x4a/0x66 [<ffffffff812ea11d>] ? __driver_attach+0x0/0x66 [<ffffffff812e96ca>] bus_for_each_dev+0x54/0x89 [<ffffffff812e9efd>] driver_attach+0x19/0x1b [<ffffffff812e9b64>] bus_add_driver+0xb4/0x204 [<ffffffff812ea41b>] driver_register+0x98/0x109 [<ffffffff813465dd>] usb_register_driver+0xb2/0x173 [<ffffffffa00ca000>] ? rt2500usb_init+0x0/0x20 [rt2500usb] [<ffffffffa00ca01e>] rt2500usb_init+0x1e/0x20 [rt2500usb] [<ffffffff81000203>] do_one_initcall+0x6d/0x17a [<ffffffff8106cae8>] sys_init_module+0x9c/0x1e0 [<ffffffff8100296b>] system_call_fastpath+0x16/0x1b Signed-off-by: Stephen Boyd <bebarino@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-07-14hostap_pci: set dev->base_addr during probeJohn W. Linville
"hostap: Protect against initialization interrupt" (which reinstated "wireless: hostap, fix oops due to early probing interrupt") reintroduced Bug 16111. This is because hostap_pci wasn't setting dev->base_addr, which is now checked in prism2_interrupt. As a result, initialization was failing for PCI-based hostap devices. This corrects that oversight. Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-07-12axnet_cs: use spin_lock_irqsave in ax_interruptKen Kawasaki
Use spin_lock_irqsave instead of spin_lock in ax_interrupt because the interrupt handler can also be invoked from ei_watchdog. Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-12Merge branch 'master' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
2010-07-11r8169: incorrect identifier for a 8168dpFrancois Romieu
Merge error. See CFG_METHOD_8 (0x3c800000 + 0x00300000) since version 8.002.00 of Realtek's driver. Signed-off-by: Francois Romieu <romieu@fr.zoreil.com> Cc: Hayes <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-07Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (35 commits) NET: SB1250: Initialize .owner vxge: show startup message with KERN_INFO ll_temac: Fix missing iounmaps bridge: Clear IPCB before possible entry into IP stack bridge br_multicast: BUG: unable to handle kernel NULL pointer dereference net: Fix definition of netif_vdbg() when VERBOSE_DEBUG is defined net/ne: fix memory leak in ne_drv_probe() xfrm: fix xfrm by MARK logic virtio_net: fix oom handling on tx virtio_net: do not reschedule rx refill forever s2io: resolve statistics issues linux/net.h: fix kernel-doc warnings net: decreasing real_num_tx_queues needs to flush qdisc sched: qdisc_reset_all_tx is calling qdisc_reset without qdisc_lock qlge: fix a eeh handler to not add a pending timer qlge: Replacing add_timer() to mod_timer() usbnet: Set parent device early for netdev_printk() net: Revert "rndis_host: Poll status channel before control channel" netfilter: ip6t_REJECT: fix a dst leak in ipv6 REJECT drivers: bluetooth: bluecard_cs.c: Fixed include error, changed to linux/io.h ...
2010-07-07NET: SB1250: Initialize .ownerRalf Baechle
Signed-off-by: Ralf Baechle <ralf@linux-mips.org> drivers/net/sb1250-mac.c | 1 + 1 files changed, 1 insertions(+), 0 deletions(-) Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-07vxge: show startup message with KERN_INFOWu Fengguang
The original KERN_CRIT will mess up terminals. CC: Sreenivasa Honnur <Sreenivasa.Honnur@neterion.com> Signed-off-by: Wu Fengguang <fengguang.wu@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-07ll_temac: Fix missing iounmapsDenis Kirjanov
Fix missing iounmaps. Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-07ath9k_htc: fix memory leak in ath9k_hif_usb_alloc_urbsRajkumar Manoharan
Failure cases within ath9k_hif_usb_alloc_urbs are failed to release allocated memory. Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-07-05net/ne: fix memory leak in ne_drv_probe()Kulikov Vasiliy
net_device allocated with alloc_eip_netdev() must be freed. Signed-off-by: Kulikov Vasiliy <segooon@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-02virtio_net: fix oom handling on txRusty Russell
virtio net will never try to overflow the TX ring, so the only reason add_buf may fail is out of memory. Thus, we can not stop the device until some request completes - there's no guarantee anything at all is outstanding. Make the error message clearer as well: error here does not indicate queue full. Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (...and avoid TX_BUSY) Cc: stable@kernel.org # .34.x (s/virtqueue_/vi->svq->vq_ops->/) Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-02virtio_net: do not reschedule rx refill foreverMichael S. Tsirkin
We currently fill all of RX ring, then add_buf returns ENOSPC, which gets mis-detected as an out of memory condition and causes us to reschedule the work, and so on forever. Fix this by oom = err == -ENOMEM; Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Cc: stable@kernel.org # .34.x Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-02s2io: resolve statistics issuesJon Mason
This patch resolves a number of issues in the statistics gathering of the s2io driver. On Xframe adapters, the received multicast statistics counter includes pause frames which are not indicated to the driver. This can cause issues where the multicast packet count is higher than what has actually been received, possibly higher than the number of packets received. The driver software counters are replaced with the adapter hardware statistics for rx_packets, rx_bytes, and tx_bytes. It also uses the overflow registers to determine if the statistics wrapped the 32bit register (removing the window of having a statistic value less than the previous call). rx_length_errors statistic now includes undersized packets in addition to oversized packets in its counting. Finally, rx_crc_errors are now being counted. Signed-off-by: Jon Mason <jon.mason@exar.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-02net: decreasing real_num_tx_queues needs to flush qdiscJohn Fastabend
Reducing real_num_queues needs to flush the qdisc otherwise skbs with queue_mappings greater then real_num_tx_queues can be sent to the underlying driver. The flow for this is, dev_queue_xmit() dev_pick_tx() skb_tx_hash() => hash using real_num_tx_queues skb_set_queue_mapping() ... qdisc_enqueue_root() => enqueue skb on txq from hash ... dev->real_num_tx_queues -= n ... sch_direct_xmit() dev_hard_start_xmit() ndo_start_xmit(skb,dev) => skb queue set with old hash skbs are enqueued on the qdisc with skb->queue_mapping set 0 < queue_mappings < real_num_tx_queues. When the driver decreases real_num_tx_queues skb's may be dequeued from the qdisc with a queue_mapping greater then real_num_tx_queues. This fixes a case in ixgbe where this was occurring with DCB and FCoE. Because the driver is using queue_mapping to map skbs to tx descriptor rings we can potentially map skbs to rings that no longer exist. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Tested-by: Ross Brattain <ross.b.brattain@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-02qlge: fix a eeh handler to not add a pending timerBreno Leitao
On some ocasions the function qlge_io_resume() tries to add a pending timer, which causes the system to hit the BUG() on add_timer() function. This patch removes the timer during the EEH recovery. Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com> Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-02qlge: Replacing add_timer() to mod_timer()Breno Leitao
Currently qlge driver calls add_timer() instead of mod_timer(). This patch changes add_timer() to mod_timer(), which seems a better solution. Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com> Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-02usbnet: Set parent device early for netdev_printk()Ben Hutchings
netdev_printk() follows the net_device's parent device pointer, so we must set that earlier than we previously did. Reported-by: Luís Picciochi Oliveira <pitxyoki@gmail.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-02net: Revert "rndis_host: Poll status channel before control channel"Ben Hutchings
This reverts commit c17b274dc2aa538b68c1f02b01a3c4e124b435ba. That change was reported to break rndis_wlan support for the WUSB54GS. Reported-by: Luís Picciochi Oliveira <pitxyoki@gmail.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-02iwlwifi: remove key information during device restartReinette Chatre
When there is a firmware error or the firmware is reloaded for some other reason we currently clear all station information, including keys associated with them. A problem is that we do not clear some other information regarding keys that are not stored in the station structs. The consequence of this is that when the device is reconfigured after the firmware reload we can, among other things, run out of key indices. This fixes: https://bugzilla.kernel.org/show_bug.cgi?id=16232 http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2221 Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com>
2010-06-30bonding: check if clients MAC addr has changedFlavio Leitner
When two systems using bonding devices in adaptive load balancing (ALB) communicates with each other, an endless ping-pong of ARP replies starts between these two systems. What happens? In the ALB mode, bonding driver keeps track of each client connected in a hash table, so it can do the receive load balancing (RLB). This hash table is updated when an ARP reply is received, then it scans for the client entry, updates its MAC address and flag it to be announced later. Therefore, two seconds later, the alb monitor runs and send for each updated client entry two ARP replies updating this specific client. The same process happens on the receiving system, causing the endless ping-pong of arp replies. See more information including the relevant functions below: System 1 System 2 bond0 bond0 ping <system2> ARP request ---------> <--------- ARP reply +->rlb_arp_recv <---------------------+ <--- loop begins | rlb_update_entry_from_arp | | client_info->ntt = 1; | | bond_info->rx_ntt = 1; | | | | <communication succeed> | | | | bond_alb_monitor | | rlb_update_rx_clients | | rlb_update_client | | arp_create(ARPOP_REPLY) | | send ARP reply --------------> V | send ARP reply --------------> | rlb_arp_recv | rlb_update_entry_from_arp | client_info->ntt = 1; | bond_info->rx_ntt = 1; | < snipped, same as in system 1> +------- <-------------- send ARP reply <-------------- send ARP reply Besides the unneeded networking traffic, this loop breaks a cluster because a backup system can't take over the IP address. There is always one system sending an ARP reply poisoning the network. This patch fixes the problem adding a check for the MAC address before updating it. Thus, if the MAC address didn't change, there is no need to update neither to announce it later. Signed-off-by: Flavio Leitner <fleitner@redhat.com> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-30mv643xx_eth: use sw csum for big packetsSaeed Bishara
Some controllers (KW, Dove) limits the TX IP/layer4 checksum offloading to a max size. Signed-off-by: Saeed Bishara <saeed@marvell.com> Acked-by: Lennert Buytenhek <buytenh@wantstofly.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-30Merge branch 'master' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
2010-06-29ixgbe: skip non IPv4 packets in ATR filterGuillaume Gaudonville
In driver ixgbe, ixgbe_atr may cause crashes for non-ipv4 packets. Just add a test to check skb->protocol. It may crash on short packets due to ip_hdr() access. Signed-off-by: Guillaume Gaudonville <guillaume.gaudonville@6wind.com> Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-29ixgbe: disable tx engine before disabling tx laserJohn Fastabend
Disabling the tx laser while receiving DMA requests can hang the device. After this occurs the device is in a bad state. The GPIO bit never clears when PCI master access is disabled and a reboot is required to get the device in a good state again. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-29ixgbe: fix panic when shutting down system with WoL enabledAndy Gospodarek
This patch added to 2.6.34: commit 5f6c01819979afbfec7e0b15fe52371b8eed87e8 Author: Jesse Brandeburg <jesse.brandeburg@intel.com> Date: Wed Apr 14 16:04:23 2010 -0700 ixgbe: fix bug with vlan strip in promsic mode among other things added a function called ixgbe_vlan_filter_enable. This new function wants to access and set some rx_ring parameters, but adapter->rx_ring has already been freed. This simply moves the free until after the access and makes __ixgbe_shutdown look more like ixgbe_remove. Signed-off-by: Andy Gospodarek <andy@greyhouse.net> Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Emil Tantilov <emil.s.tantilov@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-28bonding: prevent netpoll over bonded interfacesAndy Gospodarek
Support for netpoll over bonded interfaces was added here: commit f6dc31a85cd46a959bdd987adad14c3b645e03c1 Author: WANG Cong <amwang@redhat.com> Date: Thu May 6 00:48:51 2010 -0700 bonding: make bonding support netpoll but it is bad enough that we should probably just disable netpoll over bonding until some of the locking logic in the bonding driver is changed or converted completely to RCU. Simple actions like changing the active slave in active-backup mode will hang the box if a high enough printk debugging level is enabled. Keeping the old code around will be good for anyone that wants to work on it (and for after the RCU conversion), so I propose this small patch rather than ripping it all out. Signed-off-by: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-27Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (52 commits) phylib: Add autoload support for the LXT973 phy. ISDN: hysdn, fix potential NULL dereference vxge: fix memory leak in vxge_alloc_msix() error path isdn/gigaset: correct CAPI connection state storage isdn/gigaset: encode HLC and BC together isdn/gigaset: correct CAPI DATA_B3 Delivery Confirmation isdn/gigaset: correct CAPI voice connection encoding isdn/gigaset: honor CAPI application's buffer size request cpmac: do not leak struct net_device on phy_connect errors smc91c92_cs: fix the problem that lan & modem does not work simultaneously ipv6: fix NULL reference in proxy neighbor discovery Bluetooth: Bring back var 'i' increment xfrm: check bundle policy existance before dereferencing it sky2: enable rx/tx in sky2_phy_reinit() cnic: Disable statistics initialization for eth clients that do not support statistics net: add dependency on fw class module to qlcnic and netxen_nic snmp: fix SNMP_ADD_STATS() hso: remove setting of low_latency flag udp: Fix bogus UFO packet generation lasi82596: fix netdev_mc_count conversion ...
2010-06-26phylib: Add autoload support for the LXT973 phy.David Woodhouse
Commit e13647c1 (phylib: Add support for the LXT973 phy.) added a new ID but neglected to also add it to the MODULE_DEVICE_TABLE. Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-26vxge: fix memory leak in vxge_alloc_msix() error pathMichal Schmidt
When pci_enable_msix() returned ret<0, entries and vxge_entries were leaked. While at it, use the centralized exit idiom in the function. Signed-off-by: Michal Schmidt <mschmidt@redhat.com> Acked-by: Ram Vepa <ram.vepa@exar.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-25cpmac: do not leak struct net_device on phy_connect errorsFlorian Fainelli
If the call to phy_connect fails, we will return directly instead of freeing the previously allocated struct net_device. Signed-off-by: Florian Fainelli <florian@openwrt.org> CC: stable@kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-25smc91c92_cs: fix the problem that lan & modem does not work simultaneouslyKen Kawasaki
smc91c92_cs: Fix the problem that lan & modem does not work simultaneously in the Megahertz multi-function card. We need to write MEGAHERTZ_ISR to retrigger interrupt. Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-25iwlwifi: set TX_CMD_FLAG_PROT_REQUIRE_MSK in tx_flagWey-Yi Guy
When building tx command, always set TX_CMD_FLAG_PROT_REQUIRE_MSK for 5000 series and up. Without setting this bit the firmware will not examine the RTS/CTS setting and thus not send traffic with the appropriate protection. RTS/CTS is is required for HT traffic in a noisy environment where, without this setting, connections will stall on some hardware as documented in the patch that initially attempted to address this: commit 1152dcc28c66a74b5b3f1a3ede0aa6729bfd48e4 Author: Wey-Yi Guy <wey-yi.w.guy@intel.com> Date: Fri Jan 15 13:42:58 2010 -0800 iwlwifi: Fix throughput stall issue in HT mode for 5000 Similar to 6000 and 1000 series, RTS/CTS is the recommended protection mechanism for 5000 series in HT mode based on the HW design. Using RTS/CTS will better protect the inner exchange from interference, especially in highly-congested environment, it also prevent uCode encounter TX FIFO underrun and other HT mode related performance issues. For 3945 and 4965, different flags are used for RTS/CTS or CTS-to-Self protection. Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
2010-06-25iwlwifi: fix multicastJohannes Berg
commit 3474ad635db371b0d8d0ee40086f15d223d5b6a4 Author: Johannes Berg <johannes.berg@intel.com> Date: Thu Apr 29 04:43:05 2010 -0700 iwlwifi: apply filter flags directly broke multicast. The reason, it turns out, is that the code previously checked if ALLMULTI _changed_, which the new code no longer did, and normally it _never_ changes. Had somebody changed it manually, the code prior to my patch there would have been broken already. The reason is that we always, unconditionally, ask the device to pass up all multicast frames, but the new code made it depend on ALLMULTI which broke it since now we'd pass up multicast frames depending on the default filter in the device, which isn't necessarily what we want (since we don't program it right now). Fix this by simply not checking allmulti as we have allmulti behaviour enabled already anyway. Reported-by: Maxim Levitsky <maximlevitsky@gmail.com> Tested-by: Maxim Levitsky <maximlevitsky@gmail.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2010-06-23sky2: enable rx/tx in sky2_phy_reinit()Brandon Philips
sky2_phy_reinit is called by the ethtool helpers sky2_set_settings, sky2_nway_reset and sky2_set_pauseparam when netif_running. However, at the end of sky2_phy_init GM_GP_CTRL has GM_GPCR_RX_ENA and GM_GPCR_TX_ENA cleared. So, doing these commands causes the device to stop working: $ ethtool -r eth0 $ ethtool -A eth0 autoneg off Fix this issue by enabling Rx/Tx after running sky2_phy_init in sky2_phy_reinit. Signed-off-by: Brandon Philips <bphilips@suse.de> Tested-by: Brandon Philips <bphilips@suse.de> Cc: stable@kernel.org Tested-by: Mike McCormack <mikem@ring3k.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-23ath9k: Fix bug in starting aniVasanthakumar Thiagarajan
There are few places where ANI is started without checking if it is right to start. This might lead to a case where ani timer would be left undeleted and cause improper memory acccess during module unload. This bug is clearly exposed with paprd support where the driver detects tx hang and does a chip reset. During this reset ani is (re)started without checking if it needs to be started. This would leave a timer scheduled even after all the resources are freed and cause a panic. This patch introduces a bit in sc_flags to indicate if ani needs to be started in sw_scan_start() and ath_reset(). This would fix the following panic. This issue is easily seen with ar9003 + paprd. BUG: unable to handle kernel paging request at 0000000000003f38 [<ffffffff81075391>] ? __queue_work+0x41/0x50 [<ffffffff8106afaa>] run_timer_softirq+0x17a/0x370 [<ffffffff81088be8>] ? tick_dev_program_event+0x48/0x110 [<ffffffff81061f69>] __do_softirq+0xb9/0x1f0 [<ffffffff810ba060>] ? handle_IRQ_event+0x50/0x160 [<ffffffff8100af5c>] call_softirq+0x1c/0x30 [<ffffffff8100c9f5>] do_softirq+0x65/0xa0 [<ffffffff81061e25>] irq_exit+0x85/0x90 [<ffffffff8155e095>] do_IRQ+0x75/0xf0 [<ffffffff815570d3>] ret_from_intr+0x0/0x11 <EOI> [<ffffffff812fd67b>] ? acpi_idle_enter_simple+0xe4/0x119 [<ffffffff812fd674>] ? acpi_idle_enter_simple+0xdd/0x119 [<ffffffff81441c87>] cpuidle_idle_call+0xa7/0x140 [<ffffffff81008da3>] cpu_idle+0xb3/0x110 [<ffffffff81550722>] start_secondary+0x1ee/0x1f5 Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-23cnic: Disable statistics initialization for eth clients that do not support ↵Dmitry Kravkov
statistics Disable statistics initialization for eth clients that do not support statistics. This prevents memory corruption on bnx2x hw. Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
2010-06-23net: add dependency on fw class module to qlcnic and netxen_nicAnirban Chakraborty
netxen_nic and qlcnic driver depends on firmware_class module. Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-22Merge branch 'master' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
2010-06-22hso: remove setting of low_latency flagFilip Aben
This patch removes the setting of the low_latency flag. tty_flip_buffer_push() is occasionally being called in irq context, which causes a hang if the low_latency flag is set. Removing the low_latency flag only seems to impact the flush to ldisc, which will now be put on a workqueue. Signed-off-by: Filip Aben <f.aben@option.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-21lasi82596: fix netdev_mc_count conversionHelge Deller
Fix commit 4cd24eaf0 (net: use netdev_mc_count and netdev_mc_empty when appropriate) Signed-off-by: Helge Deller <deller@gmx.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-21NET: MIPSsim: Fix modpost warning.Ralf Baechle
$ make CONFIG_DEBUG_SECTION_MISMATCH=y [...] WARNING: drivers/net/built-in.o(.data+0x0): Section mismatch in reference from the variable mipsnet_driver to the function .init.text:mipsnet_probe() The variable mipsnet_driver references the function __init mipsnet_probe() If the reference is valid then annotate the variable with __init* or __refdata (see linux/init.h) or name the variable: *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console, [...] Fixed by making mipsnet_probe __devinit. Signed-off-by: Ralf Baechle <ralf@linux-mips.org> drivers/net/mipsnet.c | 2 +- 1 files changed, 1 insertions(+), 1 deletions(-) Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-18ath5k: initialize ah->ah_current_channelBob Copeland
ath5k assumes ah_current_channel is always a valid pointer in several places, but a newly created interface may not have a channel. To avoid null pointer dereferences, set it up to point to the first available channel until later reconfigured. This fixes the following oops: $ rmmod ath5k $ insmod ath5k $ iw phy0 set distance 11000 BUG: unable to handle kernel NULL pointer dereference at 00000006 IP: [<d0a1ff24>] ath5k_hw_set_coverage_class+0x74/0x1b0 [ath5k] *pde = 00000000 Oops: 0000 [#1] last sysfs file: /sys/devices/pci0000:00/0000:00:0e.0/ieee80211/phy0/index Modules linked in: usbhid option usb_storage usbserial usblp evdev lm90 scx200_acb i2c_algo_bit i2c_dev i2c_core via_rhine ohci_hcd ne2k_pci 8390 leds_alix2 xt_IMQ imq nf_nat_tftp nf_conntrack_tftp nf_nat_irc nf_cc Pid: 1597, comm: iw Not tainted (2.6.32.14 #8) EIP: 0060:[<d0a1ff24>] EFLAGS: 00010296 CPU: 0 EIP is at ath5k_hw_set_coverage_class+0x74/0x1b0 [ath5k] EAX: 000000c2 EBX: 00000000 ECX: ffffffff EDX: c12d2080 ESI: 00000019 EDI: cf8c0000 EBP: d0a30edc ESP: cfa09bf4 DS: 007b ES: 007b FS: 0000 GS: 0000 SS: 0068 Process iw (pid: 1597, ti=cfa09000 task=cf88a000 task.ti=cfa09000) Stack: d0a34f35 d0a353f8 d0a30edc 000000fe cf8c0000 00000000 1900063d cfa8c9e0 <0> cfa8c9e8 cfa8c0c0 cfa8c000 d0a27f0c 199d84b4 cfa8c200 00000010 d09bfdc7 <0> 00000000 00000000 ffffffff d08e0d28 cf9263c0 00000001 cfa09cc4 00000000 Call Trace: [<d0a27f0c>] ? ath5k_hw_attach+0xc8c/0x3c10 [ath5k] [<d09bfdc7>] ? __ieee80211_request_smps+0x1347/0x1580 [mac80211] [<d08e0d28>] ? nl80211_send_scan_start+0x7b8/0x4520 [cfg80211] [<c10f5db9>] ? nla_parse+0x59/0xc0 [<c11ca8d9>] ? genl_rcv_msg+0x169/0x1a0 [<c11ca770>] ? genl_rcv_msg+0x0/0x1a0 [<c11c7e68>] ? netlink_rcv_skb+0x38/0x90 [<c11c9649>] ? genl_rcv+0x19/0x30 [<c11c7c03>] ? netlink_unicast+0x1b3/0x220 [<c11c893e>] ? netlink_sendmsg+0x26e/0x290 [<c11a409e>] ? sock_sendmsg+0xbe/0xf0 [<c1032780>] ? autoremove_wake_function+0x0/0x50 [<c104d846>] ? __alloc_pages_nodemask+0x106/0x530 [<c1074933>] ? do_lookup+0x53/0x1b0 [<c10766f9>] ? __link_path_walk+0x9b9/0x9e0 [<c11acab0>] ? verify_iovec+0x50/0x90 [<c11a42b1>] ? sys_sendmsg+0x1e1/0x270 [<c1048e50>] ? find_get_page+0x10/0x50 [<c104a96f>] ? filemap_fault+0x5f/0x370 [<c1059159>] ? __do_fault+0x319/0x370 [<c11a55b4>] ? sys_socketcall+0x244/0x290 [<c101962c>] ? do_page_fault+0x1ec/0x270 [<c1019440>] ? do_page_fault+0x0/0x270 [<c1002ae5>] ? syscall_call+0x7/0xb Code: 00 b8 fe 00 00 00 b9 f8 53 a3 d0 89 5c 24 14 89 7c 24 10 89 44 24 0c 89 6c 24 08 89 4c 24 04 c7 04 24 35 4f a3 d0 e8 7c 30 60 f0 <0f> b7 43 06 ba 06 00 00 00 a8 10 75 0e 83 e0 20 83 f8 01 19 d2 EIP: [<d0a1ff24>] ath5k_hw_set_coverage_class+0x74/0x1b0 [ath5k] SS:ESP 0068:cfa09bf4 CR2: 0000000000000006 ---[ end trace 54f73d6b10ceb87b ]--- Cc: stable@kernel.org Reported-by: Steve Brown <sbrown@cortland.com> Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
generated by cgit v1.2.3-18-g5258 (git 2.32.0) at 2024-12-02 06:54:03 +0000