| Age | Commit message (Collapse) | Author |
|---|
|
abort pending TX
commit d5a7b406c529e4595ce03dc8f6dcf7fa36f106fa upstream.
In patch
0d1862e can: flexcan: fix flexcan_chip_start() on imx6
the loop in flexcan_chip_start() that iterates over all mailboxes after the
soft reset of the CAN core was removed. This loop put all mailboxes (even the
ones marked as reserved 1...7) into EMPTY/INACTIVE mode. On mailboxes 8...63,
this aborts any pending TX messages.
After a cold boot there is random garbage in the mailboxes, which leads to
spontaneous transmit of CAN frames during first activation. Further if the
interface was disabled with a pending message (usually due to an error
condition on the CAN bus), this message is retransmitted after enabling the
interface again.
This patch fixes the regression by:
1) Limiting the maximum number of used mailboxes to 8, 0...7 are used by the RX
FIFO, 8 is used by TX.
2) Marking the TX mailbox as EMPTY/INACTIVE, so that any pending TX of that
mailbox is aborted.
Cc: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
[bwh: Backported to 3.2:
- Adjust context
- Hardware local echo is still enabled]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit b98b8babd6e3370fadb7c6eaacb00eb2f6344a6c upstream.
This is primarily to address transmission timeout occurrences, when
multiple H/W Tx queues are being used concurrently. Because in
the priority scheduling mode the controller does not service the
Tx queues equally (but in ascending index order), Tx timeouts are
being triggered rightaway for a basic test with multiple simultaneous
connections like:
iperf -c <server_ip> -n 100M -P 8
resulting in kernel trace:
NETDEV WATCHDOG: eth1 (fsl-gianfar): transmit queue <X> timed out
------------[ cut here ]------------
WARNING: at net/sched/sch_generic.c:255
...
and controller reset during intense traffic, and possibly further
complications.
This patch changes the default H/W Tx scheduling setting (TXSCHED)
for multi-queue devices, from priority scheduling mode to a weighted
round robin mode with equal weights for all H/W Tx queues, and
addresses the issue above.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
This bug fix is only for stable branches older than 3.10. The bug was
fixed upstream by commit 2768935a4660 ('sfc: reuse pages to avoid DMA
mapping/unmapping costs'), but that change is totally unsuitable for
stable.
Commit b590ace09d51 ('sfc: Fix efx_rx_buf_offset() in the presence of
swiotlb') added an explicit page_offset member to struct
efx_rx_buffer, which must be set consistently with the u.page and
dma_addr fields. However, it failed to add the necessary assignment
in efx_resurrect_rx_buffer(). It also did not correct the calculation
of efx_rx_buffer::dma_addr in efx_resurrect_rx_buffer(), which assumes
that DMA-mapping a page will result in a page-aligned DMA address
(exactly what swiotlb violates).
Add the assignment of efx_rx_buffer::page_offset and change the
calculation of dma_addr to make use of it.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
commit ece793fcfc417b3925844be88a6a6dc82ae8f7c6 upstream.
We try to linearize part of the skb when the number of iov is greater than
MAX_SKB_FRAGS. This is not enough since each single vector may occupy more than
one pages, so zerocopy_sg_fromiovec() may still fail and may break the guest
network.
Solve this problem by calculate the pages needed for iov before trying to do
zerocopy and switch to use copy instead of zerocopy if it needs more than
MAX_SKB_FRAGS.
This is done through introducing a new helper to count the pages for iov, and
call uarg->callback() manually when switching from zerocopy to copy to notify
vhost.
We can do further optimization on top.
This bug were introduced from b92946e2919134ebe2a4083e4302236295ea2a73
(macvtap: zerocopy: validate vectors before building skb).
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2: callback only takes one argument]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
[ Upstream commit 7167cf0e8cd10287b7912b9ffcccd9616f382922 ]
The dma descriptors indexes are only initialized on the probe function.
If a packet is on the buffer when temac_stop is called, the dma
descriptors indexes can be left on a incorrect state where no other
package can be sent.
So an interface could be left in an usable state after ifdow/ifup.
This patch makes sure that the descriptors indexes are in a proper
status when the device is open.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
[ Upstream commit 5a0068deb611109c5ba77358be533f763f395ee4 ]
Recently grabbed this report:
https://bugzilla.redhat.com/show_bug.cgi?id=1005567
Of an issue in which the bonding driver, with an attached vlan encountered the
following errors when bond0 was taken down and back up:
dummy1: promiscuity touches roof, set promiscuity failed. promiscuity feature of
device might be broken.
The error occurs because, during __bond_release_one, if we release our last
slave, we take on a random mac address and issue a NETDEV_CHANGEADDR
notification. With an attached vlan, the vlan may see that the vlan and bond
mac address were in sync, but no longer are. This triggers a call to dev_uc_add
and dev_set_rx_mode, which enables IFF_PROMISC on the bond device. Then, when
we complete __bond_release_one, we use the current state of the bond flags to
determine if we should decrement the promiscuity of the releasing slave. But
since the bond changed promiscuity state during the release operation, we
incorrectly decrement the slave promisc count when it wasn't in promiscuous mode
to begin with, causing the above error
Fix is pretty simple, just cache the bonding flags at the start of the function
and use those when determining the need to set promiscuity.
This is also needed for the ALLMULTI flag
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Mark Wu <wudxw@linux.vnet.ibm.com>
CC: "David S. Miller" <davem@davemloft.net>
Reported-by: Mark Wu <wudxw@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
[ Upstream commit bf0ea6380724beb64f27a722dfc4b0edabff816e ]
Pass-all-multicast is controlled by bit 3 in RX control, not bit 2
(pass undersized frames).
Reported-by: Joseph Chang <joseph_chang@davicom.com.tw>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
[ Upstream commit 207070f5221e2a901d56a49df9cde47d9b716cd7 ]
Outgoing packets sent by via-rhine have their VLAN PCP field off by one
(when hardware acceleration is enabled). The TX descriptor expects only VID
and PCP (without a CFI/DEI bit).
Peter Boström noticed and reported the bug.
Signed-off-by: Roger Luethi <rl@hellgate.ch>
Cc: Peter Boström <peter.bostrom@netrounds.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
[ Upstream commit 703133de331a7a7df47f31fb9de51dc6f68a9de8 ]
If local fragmentation is allowed, then ip_select_ident() and
ip_select_ident_more() need to generate unique IDs to ensure
correct defragmentation on the peer.
For example, if IPsec (tunnel mode) has to encrypt large skbs
that have local_df bit set, then all IP fragments that belonged
to different ESP datagrams would have used the same identificator.
If one of these IP fragments would get lost or reordered, then
peer could possibly stitch together wrong IP fragments that did
not belong to the same datagram. This would lead to a packet loss
or data corruption.
Signed-off-by: Ansis Atteka <aatteka@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 0d1862ea1a5bb876cf05555a7307080cb75bf379 upstream.
In the flexcan_chip_start() function first the flexcan core is going through
the soft reset sequence, then the RX FIFO is enabled.
With the hardware is put into FIFO mode, message buffers 1...7 are reserved by
the FIFO engine. The remaining message buffers are in reset default values.
This patch removes the bogus initialization of the message buffers, as it
causes an imprecise external abort on imx6.
Reported-by: Lothar Waßmann <LW@KARO-electronics.de>
Tested-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 1e43692cdb7cc445d6347d8a5207d9cef0c71434 upstream.
Added USB ID for Corega WLUSB2GTST USB adapter.
Reported-by: Joerg Kalisch <the_force@gmx.de>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 60ce314d1750fef843e9db70050e09e49f838b69 upstream.
The private array at the end of the rtl_priv struct is not aligned.
On ARM architecture, this causes an alignment trap and is fixed by aligning
that array with __align(sizeof(void *)). That should properly align that
space according to the requirements of all architectures.
Reported-by: Jason Andrews <jasona@cadence.com>
Tested-by: Jason Andrews <jasona@cadence.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 0092820407901a0b2c4e343e85f96bb7abfcded1 upstream.
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 6e956da2027c767859128b9bfef085cf2a8e233b upstream.
We should not do temperature compensation on devices without
EXTERNAL_TX_ALC bit set (called DynamicTxAgcControl on vendor driver).
Such devices can have totally bogus TSSI parameters on the EEPROM,
but still threaded by us as valid and result doing wrong TX power
calculations.
This fix inability to connect to AP on slightly longer distance on
some Ralink chips/devices.
Reported-and-tested-by: Fabien ADAM <id2ndr@crocobox.org>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
[bwh: Backported to 3.2: use rt2x00_eeprom_read()]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit a1c781bb20ac1e03280e420abd47a99eb8bbdd3b upstream.
They are not implemented, and accessing them might trigger errors
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit e96542e55a2aacf4bdeccfe2f17b77c4895b4df2 upstream.
Similar to a race condition that exists in the tx path, the hardware
might re-read the 'next' pointer of a descriptor of the last completed
frame. This only affects non-EDMA (pre-AR93xx) devices.
To deal with this race, defer clearing and re-linking a completed rx
descriptor until the next one has been processed.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 026d5b07c03458f9c0ccd19c3850564a5409c325 upstream.
Otherwise in some cases, EAPOL frames might be filtered during the
initial handshake, causing delays and assoc failures.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
[ Upstream commit 15718ea0d844e4816dbd95d57a8a0e3e264ba90e ]
The recent fix d9bf5f1309 "tun: compare with 0 instead of total_len" is
not totally correct. Because "len" and "sizeof()" are size_t type, that
means they are never less than zero.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
[ Upstream commits cf3c4c03060b688cbc389ebc5065ebcce5653e96 and
d06f5187469eee1b2932c02fd093d113cfc60d5e (the latter is a fixup
from Dave Jones) ]
Self explanitory dma_mapping_error addition to the 8139 driver, based on this:
https://bugzilla.redhat.com/show_bug.cgi?id=947250
It showed several backtraces arising for dma_map_* usage without checking the
return code on the mapping. Add the check and abort the rx/tx operation if its
failed. Untested as I have no hardware and the reporter has wandered off, but
seems pretty straightforward.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit d2e9fc141e2aa21f4b35ee27072d84e9aa6e2ba0 upstream.
ath9k_htc adds padding between the 802.11 header and the payload during
TX by moving the header. When handing the frame back to mac80211 for TX
status handling the header is not moved back into its original position.
This can result in a too small skb headroom when entering ath9k_htc
again (due to a soft retransmission for example) causing an
skb_under_panic oops.
Fix this by moving the 802.11 header back into its original position
before returning the frame to mac80211 as other drivers like rt2x00
or ath5k do.
Reported-by: Marc Kleine-Budde <mkl@blackshift.org>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Tested-by: Marc Kleine-Budde <mkl@blackshift.org>
Signed-off-by: Marc Kleine-Budde <mkl@blackshift.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit b2fcc0aee58a3435566dd6d8501a0b355552f28b upstream.
My current 3.11 fix:
commit 788f7a56fce1bcb2067b62b851a086fca48a0056
Author: Stanislaw Gruszka <sgruszka@redhat.com>
Date: Thu Aug 1 12:07:55 2013 +0200
iwl4965: reset firmware after rfkill off
broke rfkill notification to user-space . I missed that bug, because
I compiled without CONFIG_RFKILL, sorry about that.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
[bwh: Backported to 3.2: adjust filename, context, naming]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 909bd5926d474e275599094acad986af79671ac9 upstream.
We want the data stored in "addr" and "qual", but the extra ampersands
mean we are copying stack data instead.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 1206ff4ff9d2ef7468a355328bc58ac6ebf5be44 upstream.
Patch fixes zd1201 not to use stack as URB transfer_buffer. URB buffers need
to be DMA-able, which stack is not.
Patch is only compile tested.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 788f7a56fce1bcb2067b62b851a086fca48a0056 upstream.
Using rfkill switch can make firmware unstable, what cause various
Microcode errors and kernel warnings. Reseting firmware just after
rfkill off (radio on) helped with that.
Resolve:
https://bugzilla.redhat.com/show_bug.cgi?id=977053
Reported-and-tested-by: Justin Pearce <whitefox@guardianfox.net>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
[bwh: Backported to 3.2: adjust filenames, context, naming]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit eca396d7a5bdcc1fd67b1b12f737c213ac78a6f4 upstream.
If device was put into a sleep and system was restarted or module
reloaded, we have to wake device up before sending other commands.
Otherwise it will fail to start with Microcode error.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
[bwh: Backported to 3.2: adjust filename, context, naming]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 9186a1fd9ed190739423db84bc344d258ef3e3d7 upstream.
If channel switch is pending and we remove interface we can
crash like showed below due to passing NULL vif to mac80211:
BUG: unable to handle kernel paging request at fffffffffffff8cc
IP: [<ffffffff8130924d>] strnlen+0xd/0x40
Call Trace:
[<ffffffff8130ad2e>] string.isra.3+0x3e/0xd0
[<ffffffff8130bf99>] vsnprintf+0x219/0x640
[<ffffffff8130c481>] vscnprintf+0x11/0x30
[<ffffffff81061585>] vprintk_emit+0x115/0x4f0
[<ffffffff81657bd5>] printk+0x61/0x63
[<ffffffffa048987f>] ieee80211_chswitch_done+0xaf/0xd0 [mac80211]
[<ffffffffa04e7b34>] iwl_chswitch_done+0x34/0x40 [iwldvm]
[<ffffffffa04f83c3>] iwlagn_commit_rxon+0x2a3/0xdc0 [iwldvm]
[<ffffffffa04ebc50>] ? iwlagn_set_rxon_chain+0x180/0x2c0 [iwldvm]
[<ffffffffa04e5e76>] iwl_set_mode+0x36/0x40 [iwldvm]
[<ffffffffa04e5f0d>] iwlagn_mac_remove_interface+0x8d/0x1b0 [iwldvm]
[<ffffffffa0459b3d>] ieee80211_do_stop+0x29d/0x7f0 [mac80211]
This is because we nulify ctx->vif in iwlagn_mac_remove_interface()
before calling some other functions that teardown interface. To fix
just check ctx->vif on iwl_chswitch_done(). We should not call
ieee80211_chswitch_done() as channel switch works were already canceled
by mac80211 in ieee80211_do_stop() -> ieee80211_mgd_stop().
Resolve:
https://bugzilla.redhat.com/show_bug.cgi?id=979581
Reported-by: Lukasz Jagiello <jagiello.lukasz@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
[bwh: Backported to 3.2: adjust context, filename]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit e2288b66fe7ff0288382b2af671b4da558b44472 upstream.
Since we clear QUEUE_STARTED in rt2x00queue_stop_queue(), following
call to rt2x00queue_pause_queue() reduce to noop, i.e we do not
stop queue in mac80211.
To fix that introduce rt2x00queue_pause_queue_nocheck() function,
which will stop queue in mac80211 directly.
Note that rt2x00_start_queue() explicitly set QUEUE_PAUSED bit.
Note also that reordering operations i.e. first call to
rt2x00queue_pause_queue() and then clear QUEUE_STARTED bit, will race
with rt2x00queue_unpause_queue(), so calling ieee80211_stop_queue()
directly is the only available solution to fix the problem without
major rework.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 1eb9ac14c34a948bf1538bfb9034e8ab29099a64 upstream.
This patch fixes an issue with the 82598EB device, where lldpad is causing Tx
Hangs on the card as soon as it attempts to configure DCB for the device. The
adapter will continually Tx hang and reset in a loop.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Jack Morgan <jack.morgan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 83e612f632c3897be29ef02e0472f6d63e258378 upstream.
Both type and pkt_len variables are in host endian and these should be in
Little Endian in the payload.
Signed-off-by: Tomasz Moń <desowin@gmail.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit dc2a87f519a4d8cb376ab54f22b6b98a943b51ce upstream.
Currently we configure harwdare and clock, only after
interface start. In this case, if we reload module or
reboot PC without configuring adapter, firmware will freeze.
There is no software way to reset adpter.
This patch add initial configuration and set it in
disabled state, to avoid this freeze. Behaviour of this patch
should be similar to: ifconfig wlan0 up; ifconfig wlan0 down.
Bug: https://github.com/qca/open-ath9k-htc-firmware/issues/1
Tested-by: Bo Shi <cnshibo@gmail.com>
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit a1923f1d4723e5757cefdd60f7c7ab30e472007a upstream.
This SKU was missing in the list of supported devices
https://bugzilla.kernel.org/show_bug.cgi?id=60577
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
[bwh: Backported to 3.2: adjust filename]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 707aee401d2467baa785a697f40a6e2d9ee79ad5 upstream.
The BT_CONFIG command that is sent to the device during
startup will enable BT coex unless the module parameter
turns it off, but on devices without Bluetooth this may
cause problems, as reported in Redhat BZ 885407.
Fix this by sending the BT_CONFIG command only when the
device has Bluetooth.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
[bwh: Backported to 3.2:
- Adjust filename
- s/priv->lib/priv->cfg/]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
[ Upstream commit 20f0170377264e8449b6987041f0bcc4d746d3ed ]
usbnet doesn't support yet SG, so drivers should not advertise SG or TSO
capabilities, as they allow TCP stack to build large TSO packets that
need to be linearized and might use order-5 pages.
This adds an extra copy overhead and possible allocation failures.
Current code ignore skb_linearize() return code so crashes are even
possible.
Best is to not pretend SG/TSO is supported, and add this again when/if
usbnet really supports SG for devices who could get a performance gain.
Based on a prior patch from Freddy Xin <freddy@asix.com.tw>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
[ Upstream commit 087d273caf4f7d3f2159256f255f1f432bc84a5b ]
This patch doesn't change the compiled code because ARC_HDR_SIZE is 4
and sizeof(int) is 4, but the intent was to use the header size and not
the sizeof the header size.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit b51c3427e95b ('ifb: fix rcu_sched self-detected stalls', commit
440d57bc5ff5 upstream) added a call to cond_resched(), which is
declared in '#include <linux/sched.h>'. In Linux 3.2.y that header is
included indirectly in some but not all configurations, so add a
direct #include.
Reported-by: Teck Choon Giam <giamteckchoon@gmail.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit cbdadbbf0c790f79350a8f36029208944c5487d0 upstream.
virtio net called virtqueue_enable_cq on RX path after napi_complete, so
with NAPI_STATE_SCHED clear - outside the implicit napi lock.
This violates the requirement to synchronize virtqueue_enable_cq wrt
virtqueue_add_buf. In particular, used event can move backwards,
causing us to lose interrupts.
In a debug build, this can trigger panic within START_USE.
Jason Wang reports that he can trigger the races artificially,
by adding udelay() in virtqueue_enable_cb() after virtio_mb().
However, we must call napi_complete to clear NAPI_STATE_SCHED before
polling the virtqueue for used buffers, otherwise napi_schedule_prep in
a callback will fail, causing us to lose RX events.
To fix, call virtqueue_enable_cb_prepare with NAPI_STATE_SCHED
set (under napi lock), later call virtqueue_poll with
NAPI_STATE_SCHED clear (outside the lock).
Reported-by: Jason Wang <jasowang@redhat.com>
Tested-by: Jason Wang <jasowang@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[wg: Backported to 3.2]
Signed-off-by: Wolfram Gloger <wmglo@dent.med.uni-muenchen.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
[ Upstream commit 584ec4355355ffac43571b02a314d43eb2f7fcbf ]
Ben Hutchings pointed out that my recent update to atl1e
in commit 352900b583b2852152a1e05ea0e8b579292e731e
("atl1e: fix dma mapping warnings") was missing a bit of code.
Specifically it reset the hardware tx ring to its origional state when
we hit a dma error, but didn't unmap any exiting mappings from the
operation. This patch fixes that up. It also remembers to free the
skb in the event that an error occurs, so we don't leak. Untested, as
I don't have hardware. I think its pretty straightforward, but please
review closely.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
CC: Jay Cliburn <jcliburn@gmail.com>
CC: Chris Snook <chris.snook@gmail.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
[ Upstream commit 352900b583b2852152a1e05ea0e8b579292e731e ]
Recently had this backtrace reported:
WARNING: at lib/dma-debug.c:937 check_unmap+0x47d/0x930()
Hardware name: System Product Name
ATL1E 0000:02:00.0: DMA-API: device driver failed to check map error[device
address=0x00000000cbfd1000] [size=90 bytes] [mapped as single]
Modules linked in: xt_conntrack nf_conntrack ebtable_filter ebtables
ip6table_filter ip6_tables snd_hda_codec_hdmi snd_hda_codec_realtek iTCO_wdt
iTCO_vendor_support snd_hda_intel acpi_cpufreq mperf coretemp btrfs zlib_deflate
snd_hda_codec snd_hwdep microcode raid6_pq libcrc32c snd_seq usblp serio_raw xor
snd_seq_device joydev snd_pcm snd_page_alloc snd_timer snd lpc_ich i2c_i801
soundcore mfd_core atl1e asus_atk0110 ata_generic pata_acpi radeon i2c_algo_bit
drm_kms_helper ttm drm i2c_core pata_marvell uinput
Pid: 314, comm: systemd-journal Not tainted 3.9.0-0.rc6.git2.3.fc19.x86_64 #1
Call Trace:
<IRQ> [<ffffffff81069106>] warn_slowpath_common+0x66/0x80
[<ffffffff8106916c>] warn_slowpath_fmt+0x4c/0x50
[<ffffffff8138151d>] check_unmap+0x47d/0x930
[<ffffffff810ad048>] ? sched_clock_cpu+0xa8/0x100
[<ffffffff81381a2f>] debug_dma_unmap_page+0x5f/0x70
[<ffffffff8137ce30>] ? unmap_single+0x20/0x30
[<ffffffffa01569a1>] atl1e_intr+0x3a1/0x5b0 [atl1e]
[<ffffffff810d53fd>] ? trace_hardirqs_off+0xd/0x10
[<ffffffff81119636>] handle_irq_event_percpu+0x56/0x390
[<ffffffff811199ad>] handle_irq_event+0x3d/0x60
[<ffffffff8111cb6a>] handle_fasteoi_irq+0x5a/0x100
[<ffffffff8101c36f>] handle_irq+0xbf/0x150
[<ffffffff811dcb2f>] ? file_sb_list_del+0x3f/0x50
[<ffffffff81073b10>] ? irq_enter+0x50/0xa0
[<ffffffff8172738d>] do_IRQ+0x4d/0xc0
[<ffffffff811dcb2f>] ? file_sb_list_del+0x3f/0x50
[<ffffffff8171c6b2>] common_interrupt+0x72/0x72
<EOI> [<ffffffff810db5b2>] ? lock_release+0xc2/0x310
[<ffffffff8109ea04>] lg_local_unlock_cpu+0x24/0x50
[<ffffffff811dcb2f>] file_sb_list_del+0x3f/0x50
[<ffffffff811dcb6d>] fput+0x2d/0xc0
[<ffffffff811d8ea1>] filp_close+0x61/0x90
[<ffffffff811fae4d>] __close_fd+0x8d/0x150
[<ffffffff811d8ef0>] sys_close+0x20/0x50
[<ffffffff81725699>] system_call_fastpath+0x16/0x1b
The usual straighforward failure to check for dma_mapping_error after a map
operation is completed.
This patch should fix it, the reporter wandered off after filing this bz:
https://bugzilla.redhat.com/show_bug.cgi?id=954170
and I don't have hardware to test, but the fix is pretty straightforward, so I
figured I'd post it for review.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Jay Cliburn <jcliburn@gmail.com>
CC: Chris Snook <chris.snook@gmail.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
[ Upstream commit f2966cd5691058b8674a20766525bedeaea9cbcf ]
If __rtnl_link_register() return faild when loading the ifb, it will
take the wrong path and get oops, so fix it just like dummy.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
[ Upstream commit 2c8a01894a12665d8059fad8f0a293c98a264121 ]
We rename the dummy in modprobe.conf like this:
install dummy0 /sbin/modprobe -o dummy0 --ignore-install dummy
install dummy1 /sbin/modprobe -o dummy1 --ignore-install dummy
We got oops when we run the command:
modprobe dummy0
modprobe dummy1
------------[ cut here ]------------
[ 3302.187584] BUG: unable to handle kernel NULL pointer dereference at 0000000000000008
[ 3302.195411] IP: [<ffffffff813fe62a>] __rtnl_link_unregister+0x9a/0xd0
[ 3302.201844] PGD 85c94a067 PUD 8517bd067 PMD 0
[ 3302.206305] Oops: 0002 [#1] SMP
[ 3302.299737] task: ffff88105ccea300 ti: ffff880eba4a0000 task.ti: ffff880eba4a0000
[ 3302.307186] RIP: 0010:[<ffffffff813fe62a>] [<ffffffff813fe62a>] __rtnl_link_unregister+0x9a/0xd0
[ 3302.316044] RSP: 0018:ffff880eba4a1dd8 EFLAGS: 00010246
[ 3302.321332] RAX: 0000000000000000 RBX: ffffffff81a9d738 RCX: 0000000000000002
[ 3302.328436] RDX: 0000000000000000 RSI: ffffffffa04d602c RDI: ffff880eba4a1dd8
[ 3302.335541] RBP: ffff880eba4a1e18 R08: dead000000200200 R09: dead000000100100
[ 3302.342644] R10: 0000000000000080 R11: 0000000000000003 R12: ffffffff81a9d788
[ 3302.349748] R13: ffffffffa04d7020 R14: ffffffff81a9d670 R15: ffff880eba4a1dd8
[ 3302.364910] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 3302.370630] CR2: 0000000000000008 CR3: 000000085e15e000 CR4: 00000000000427e0
[ 3302.377734] DR0: 0000000000000003 DR1: 00000000000000b0 DR2: 0000000000000001
[ 3302.384838] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
[ 3302.391940] Stack:
[ 3302.393944] ffff880eba4a1dd8 ffff880eba4a1dd8 ffff880eba4a1e18 ffffffffa04d70c0
[ 3302.401350] 00000000ffffffef ffffffffa01a8000 0000000000000000 ffffffff816111c8
[ 3302.408758] ffff880eba4a1e48 ffffffffa01a80be ffff880eba4a1e48 ffffffffa04d70c0
[ 3302.416164] Call Trace:
[ 3302.418605] [<ffffffffa01a8000>] ? 0xffffffffa01a7fff
[ 3302.423727] [<ffffffffa01a80be>] dummy_init_module+0xbe/0x1000 [dummy0]
[ 3302.430405] [<ffffffffa01a8000>] ? 0xffffffffa01a7fff
[ 3302.435535] [<ffffffff81000322>] do_one_initcall+0x152/0x1b0
[ 3302.441263] [<ffffffff810ab24b>] do_init_module+0x7b/0x200
[ 3302.446824] [<ffffffff810ad3d2>] load_module+0x4e2/0x530
[ 3302.452215] [<ffffffff8127ae40>] ? ddebug_dyndbg_boot_param_cb+0x60/0x60
[ 3302.458979] [<ffffffff810ad5f1>] SyS_init_module+0xd1/0x130
[ 3302.464627] [<ffffffff814b9652>] system_call_fastpath+0x16/0x1b
[ 3302.490090] RIP [<ffffffff813fe62a>] __rtnl_link_unregister+0x9a/0xd0
[ 3302.496607] RSP <ffff880eba4a1dd8>
[ 3302.500084] CR2: 0000000000000008
[ 3302.503466] ---[ end trace 8342d49cd49f78ed ]---
The reason is that when loading dummy, if __rtnl_link_register() return failed,
the init_module should return and avoid take the wrong path.
Signed-off-by: Tan Xiaojun <tanxiaojun@huawei.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
[ Upstream commit 61d46bf979d5cd7c164709a80ad5676a35494aae ]
Userspace may produce vectors greater than MAX_SKB_FRAGS. When we try to
linearize parts of the skb to let the rest of iov to be fit in
the frags, we need count copylen into linear when calling macvtap_alloc_skb()
instead of partly counting it into data_len. Since this breaks
zerocopy_sg_from_iovec() since its inner counter assumes nr_frags should
be zero at beginning. This cause nr_frags to be increased wrongly without
setting the correct frags.
This bug were introduced from b92946e2919134ebe2a4083e4302236295ea2a73
(macvtap: zerocopy: validate vectors before building skb).
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
[ Upstream commit 440d57bc5ff55ec1efb3efc9cbe9420b4bbdfefa ]
According to the commit 16b0dc29c1af9df341428f4c49ada4f626258082
(dummy: fix rcu_sched self-detected stalls)
Eric Dumazet fix the problem in dummy, but the ifb will occur the
same problem like the dummy modules.
Trying to "modprobe ifb numifbs=30000" triggers :
INFO: rcu_sched self-detected stall on CPU
After this splat, RTNL is locked and reboot is needed.
We must call cond_resched() to avoid this, even holding RTNL.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
[ Upstream commit aabb9875d02559ab9b928cd6f259a5cc4c21a589 ]
The missing call to unregister_netdev() leaves the interface active
after the driver is unloaded by rmmod.
Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
[ Upstream commit ca8c35852138ee0585eaffe6b9f10a5261ea7771 ]
EESR.RFE (receive FIFO overflow) interrupt is enabled by the driver on all SoCs
and sh_eth_error() handles it but it's not present in any initializer/assignment
of the 'eesr_err_check' field of 'struct sh_eth_cpu_data'. This leads to that
interrupt not being handled and cleared, and finally to disabling IRQ and the
driver being non-functional.
Modify DEFAULT_EESR_ERR_CHECK macro and all explicit initializers of the above
mentioned field to contain the EESR.RFE bit. Remove useless backslashes from the
initializers, while at it.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
[ Upstream commit 4c7ab054ab4f5d63625508ed6f8a607184cae7c2 ]
get user pages might fail partially in macvtap zero copy
mode. To recover we need to put all pages that we got,
but code used a wrong index resulting in double-free
errors.
Reported-by: Brad Hubbard <bhubbard@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 578a1310f2592ba90c5674bca21c1dbd1adf3f0a upstream.
We triggered an oops while running trinity with 3.4 kernel:
BUG: unable to handle kernel paging request at 0000000100000d07
IP: [<ffffffffa0109738>] dlci_ioctl+0xd8/0x2d4 [dlci]
PGD 640c0d067 PUD 0
Oops: 0000 [#1] PREEMPT SMP
CPU 3
...
Pid: 7302, comm: trinity-child3 Not tainted 3.4.24.09+ 40 Huawei Technologies Co., Ltd. Tecal RH2285 /BC11BTSA
RIP: 0010:[<ffffffffa0109738>] [<ffffffffa0109738>] dlci_ioctl+0xd8/0x2d4 [dlci]
...
Call Trace:
[<ffffffff8137c5c3>] sock_ioctl+0x153/0x280
[<ffffffff81195494>] do_vfs_ioctl+0xa4/0x5e0
[<ffffffff8118354a>] ? fget_light+0x3ea/0x490
[<ffffffff81195a1f>] sys_ioctl+0x4f/0x80
[<ffffffff81478b69>] system_call_fastpath+0x16/0x1b
...
It's because the net device is not a dlci device.
Reported-by: Li Jinyue <lijinyue@huawei.com>
Signed-off-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 11eb2645cbf38a08ae491bf6c602eea900ec0bb5 upstream.
Otherwise the net device returned can be freed at anytime.
Signed-off-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 10d0b9030a3f86e1e26c710c7580524d7787d688 upstream.
A typo causes routine rtl92cu_phy_rf6052_set_cck_txpower() to test the
same condition twice. The problem was found using cppcheck-1.49, and the
proper fix was verified against the pre-mac80211 version of the code.
This patch was originally included as commit 1288aa4, but was accidentally
reverted in a later patch.
Reported-by: David Binderman <dcb314@hotmail.com> [original report]
Reported-by: Andrea Morello <andrea.merello@gmail.com> [report of accidental reversion]
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit c4d827c5ccc3a49227dbf9d4b248a2e86f388023 upstream.
This is a new device for this driver.
Reported-by: Tobias Kluge <zielscheibe@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Tobias Kluge <zielscheibe@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit d3bcb7b24bbf09fde8405770e676fe0c11c79662 upstream.
ah->noise is maintained globally and not per-channel. This
is updated in the reset() routine after the NF history has been
filled for the *current channel*, just before switching to
the new channel. There is no need to do it inside getnf(), since
ah->noise must contain a value for the new channel.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
