aboutsummaryrefslogtreecommitdiff
path: root/drivers/net
AgeCommit message (Collapse)Author
2010-01-13tg3: Fix std prod ring nicaddr for 5787 and 57765Matt Carlson
Commit 87668d352aa8d135bd695a050f18bbfc7b50b506, titled "tg3: Don't touch RCB nic addresses", tried to avoid assigning the nic address of the standard producer ring. Unfortunately, the default nic address is not correct for the 5787, the 5755M, or the 57765. This patch reenables the old behavior and opts out of the assignment only for the 5717. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Tested-by: Chow Loong Jin <hyperair@ubuntu.com> Tested-by: Dmitry Torokhov <dtor@mail.ru> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-13sfc: Fix conditions for MDIO self-testBen Hutchings
The MDIO self-test should not be run on boards without an MDIO PHY, such as SFN5122F-R3 and later revisions. It should also not try to address a specific MMD in an MDIO clause 22 PHY. Check the mode_support field to decide which mode to use, if any. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-13sfc: Fix polling for slow MCDI operationsBen Hutchings
When the interface is down and we are using polled mode for MCDI operations, we busy-wait for completion for approximately 1 jiffy using udelay() and then back off to schedule(). But the completion will not wake the task, since we are using polled mode! We must use schedule_timeout_uninterruptible() instead. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-13e1000e: workaround link issues on busy hub in half duplex on 82577/82578Bruce Allan
This patch removes a delay in hardware after every received packet allowing more time for transmitted packets to go out in between received packets in half duplex. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-13e1000e: MDIO slow mode should always be done for 82577Bruce Allan
A previous 82577 workaround that set the MDIO access speed to slow mode for every PHY register read/write when the cable is unplugged should instead set the access mode to always be slow before any PHY register access. Since the mode bit gets cleared when the PHY is reset, set the mode after every PHY reset. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-13ixgbe: update copyright datesShannon Nelson
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-13ixgbe: Do not attempt to perform interrupts in netpoll when downAlexander Duyck
This patch resolves issues seen when running netconsole and rebooting via reboot -f. The issue was due to the fact that we were attempting to perform interrupt actions when the q_vectors and rings had already been freed via the ixgbe_shutdown routines. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-12Merge branch 'master' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
2010-01-12sky2: Fix oops in sky2_xmit_frame() after TX timeoutJarek Poplawski
During TX timeout procedure dev could be awoken too early, e.g. by sky2_complete_tx() called from sky2_down(). Then sky2_xmit_frame() can run while buffers are freed causing an oops. This patch fixes it by adding netif_device_present() test in sky2_tx_complete(). Fixes: http://bugzilla.kernel.org/show_bug.cgi?id=14925 With debugging by: Mike McCormack <mikem@ring3k.org> Reported-by: Berck E. Nash <flyboy@gmail.com> Tested-by: Berck E. Nash <flyboy@gmail.com> Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-11iwlwifi: silence buffer overflow warningDan Carpenter
Smatch (and presumably other static checkers) complain that MAX_TID_COUNT is past the end of the array. In the resulting discussion, Zhu Yi pointed out that this value is not used in real life and the assignment was only there to silence a gcc warning. If there were a bug in the surrounding code and the value were used, the WARN_ON(!qc) would print a warning before the crash. Signed-off-by: Dan Carpenter <error27@gmail.com> Acked-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-01-10vxge: use pci_dma_mapping_error to test return valueDenis Kirjanov
pci_dma_mapping_error should be used to test return value of pci_map_single or pci_map_page. Signed-off-by: Denis Kirjanov <kirjanov@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-08iwlwifi: disable tx on beacon update notificationAbhijeet Kolekar
On beacon change update notification from mac we are not disabling the tx in adhoc mode. Mac sends BSS_CHANGED_BEACON_ENABLED when station leaves IBSS. Driver should indicate uCode to not to send anything on receiving this notification. Functionality to indicate uCode is duplicated across two notifications so created a common function called iwl_set_no_assoc. Fix the issue at http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2133. Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com> Tested-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-01-08iwlwifi: fix iwl_queue_used bug when read_ptr == write_ptrZhu Yi
When txq read_ptr equals to write_ptr, iwl_queue_used should always return false. Because there is no used TFD in this case. This is a complementary fix to the fix already included in commit "iwl3945: fix panic in iwl3945 driver". Both fixes are needed to address the panic below. This problem was discussed on linux-wireless in http://thread.gmane.org/gmane.linux.kernel.wireless.general/43568 <1>[ 7290.414172] IP: [<ffffffffa0dd53a1>] iwl3945_rx_reply_tx+0xc1/0x450 [iwl3945] <4>[ 7290.414205] PGD 0 <1>[ 7290.414214] Thread overran stack, or stack corrupted <0>[ 7290.414229] Oops: 0002 [#1] PREEMPT SMP <0>[ 7290.414246] last sysfs file: /sys/devices/platform/coretemp.1/temp1_input <4>[ 7290.414265] CPU 0 <4>[ 7290.414274] Modules linked in: af_packet nfsd usb_storage usb_libusual cpufreq_powersave exportfs cpufreq_conservative iwl3945 nfs cpufreq_userspace snd_hda_codec_realtek acpi_cpufreq uvcvideo lockd iwlcore snd_hda_intel joydev coretemp nfs_acl videodev snd_hda_codec mac80211 v4l1_compat snd_hwdep sbp2 v4l2_compat_ioctl32 uhci_hcd psmouse auth_rpcgss ohci1394 cfg80211 ehci_hcd video ieee1394 snd_pcm serio_raw battery ac nvidia(P) usbcore output sunrpc evdev lirc_ene0100 snd_page_alloc rfkill tg3 libphy fuse lzo lzo_decompress lzo_compress <6>[ 7290.414486] Pid: 0, comm: swapper Tainted: P 2.6.32-rc8-wl #213 Aspire 5720 <6>[ 7290.414507] RIP: 0010:[<ffffffffa0dd53a1>] [<ffffffffa0dd53a1>] iwl3945_rx_reply_tx+0xc1/0x450 [iwl3945] <6>[ 7290.414541] RSP: 0018:ffff880002203d60 EFLAGS: 00010246 <6>[ 7290.414557] RAX: 000000000000004f RBX: ffff880064c11600 RCX: 0000000000000013 <6>[ 7290.414576] RDX: ffffffffa0ddcf20 RSI: ffff8800512b7008 RDI: 0000000000000038 <6>[ 7290.414596] RBP: ffff880002203dd0 R08: 0000000000000000 R09: 0000000000000100 <6>[ 7290.414616] R10: 0000000000000001 R11: 0000000000000000 R12: 00000000000000a0 <6>[ 7290.414635] R13: 0000000000000002 R14: 0000000000000013 R15: 0000000000020201 <6>[ 7290.414655] FS: 0000000000000000(0000) GS:ffff880002200000(0000) knlGS:0000000000000000 <6>[ 7290.414677] CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b <6>[ 7290.414693] CR2: 0000000000000041 CR3: 0000000001001000 CR4: 00000000000006f0 <6>[ 7290.414712] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 <6>[ 7290.414732] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 <4>[ 7290.414752] Process swapper (pid: 0, threadinfo ffffffff81524000, task ffffffff81528b60) <0>[ 7290.414772] Stack: <4>[ 7290.414780] ffff880002203da0 0000000000000046 0000000000000000 0000000000000046 <4>[ 7290.414804] <0> 0000000000000282 0000000000000282 0000000000000282 ffff880064c12010 <4>[ 7290.414830] <0> ffff880002203db0 ffff880064c11600 ffff880064c12e50 ffff8800512b7000 <0>[ 7290.414858] Call Trace: <0>[ 7290.414867] <IRQ> <4>[ 7290.414884] [<ffffffffa0dc8c47>] iwl3945_irq_tasklet+0x657/0x1740 [iwl3945] <4>[ 7290.414910] [<ffffffff8138fc60>] ? _spin_unlock+0x30/0x60 <4>[ 7290.414931] [<ffffffff81049a21>] tasklet_action+0x101/0x110 <4>[ 7290.414950] [<ffffffff8104a3d0>] __do_softirq+0xc0/0x160 <4>[ 7290.414968] [<ffffffff8100d01c>] call_softirq+0x1c/0x30 <4>[ 7290.414986] [<ffffffff8100eff5>] do_softirq+0x75/0xb0 <4>[ 7290.415003] [<ffffffff81049ee5>] irq_exit+0x95/0xa0 <4>[ 7290.415020] [<ffffffff8100e547>] do_IRQ+0x77/0xf0 <4>[ 7290.415038] [<ffffffff8100c7d3>] ret_from_intr+0x0/0xf <0>[ 7290.415052] <EOI> <4>[ 7290.415067] [<ffffffff81234efa>] ? acpi_idle_enter_bm+0x270/0x2a5 <4>[ 7290.415087] [<ffffffff81234f04>] ? acpi_idle_enter_bm+0x27a/0x2a5 <4>[ 7290.415107] [<ffffffff81234efa>] ? acpi_idle_enter_bm+0x270/0x2a5 <4>[ 7290.415130] [<ffffffff812c11f3>] ? cpuidle_idle_call+0x93/0xf0 <4>[ 7290.415149] [<ffffffff8100b0d7>] ? cpu_idle+0xa7/0x110 <4>[ 7290.415168] [<ffffffff8137b3d5>] ? rest_init+0x75/0x80 <4>[ 7290.415187] [<ffffffff8158cd0a>] ? start_kernel+0x3a7/0x3b3 <4>[ 7290.415206] [<ffffffff8158c315>] ? x86_64_start_reservations+0x125/0x129 <4>[ 7290.415227] [<ffffffff8158c3fd>] ? x86_64_start_kernel+0xe4/0xeb <0>[ 7290.415243] Code: 00 41 39 ce 0f 8d e8 01 00 00 48 8b 47 40 48 63 d2 48 69 d2 98 00 00 00 4c 8b 04 02 48 c7 c2 20 cf dd a0 49 8d 78 38 49 8d 40 4f <c6> 47 09 00 c6 47 0c 00 c6 47 0f 00 c6 47 12 00 c6 47 15 00 49 <1>[ 7290.415382] RIP [<ffffffffa0dd53a1>] iwl3945_rx_reply_tx+0xc1/0x450 [iwl3945] <4>[ 7290.415410] RSP <ffff880002203d60> <0>[ 7290.415421] CR2: 0000000000000041 <4>[ 7290.415436] ---[ end trace ec46807277caa515 ]--- <0>[ 7290.415450] Kernel panic - not syncing: Fatal exception in interrupt <4>[ 7290.415468] Pid: 0, comm: swapper Tainted: P D 2.6.32-rc8-wl #213 <4>[ 7290.415486] Call Trace: <4>[ 7290.415495] <IRQ> [<ffffffff8138c040>] panic+0x7d/0x13a <4>[ 7290.415519] [<ffffffff8101071a>] oops_end+0xda/0xe0 <4>[ 7290.415538] [<ffffffff8102e1ea>] no_context+0xea/0x250 <4>[ 7290.415557] [<ffffffff81038991>] ? select_task_rq_fair+0x511/0x780 <4>[ 7290.415578] [<ffffffff8102e475>] __bad_area_nosemaphore+0x125/0x1e0 <4>[ 7290.415597] [<ffffffff81038d0c>] ? __enqueue_entity+0x7c/0x80 <4>[ 7290.415616] [<ffffffff81039201>] ? enqueue_task_fair+0x111/0x150 <4>[ 7290.415636] [<ffffffff8102e53e>] bad_area_nosemaphore+0xe/0x10 <4>[ 7290.415656] [<ffffffff8102e8fa>] do_page_fault+0x26a/0x320 <4>[ 7290.415674] [<ffffffff813905df>] page_fault+0x1f/0x30 <4>[ 7290.415697] [<ffffffffa0dd53a1>] ? iwl3945_rx_reply_tx+0xc1/0x450 [iwl3945] <4>[ 7290.415723] [<ffffffffa0dc8c47>] iwl3945_irq_tasklet+0x657/0x1740 [iwl3945] <4>[ 7290.415746] [<ffffffff8138fc60>] ? _spin_unlock+0x30/0x60 <4>[ 7290.415764] [<ffffffff81049a21>] tasklet_action+0x101/0x110 <4>[ 7290.415783] [<ffffffff8104a3d0>] __do_softirq+0xc0/0x160 <4>[ 7290.415801] [<ffffffff8100d01c>] call_softirq+0x1c/0x30 <4>[ 7290.415818] [<ffffffff8100eff5>] do_softirq+0x75/0xb0 <4>[ 7290.415835] [<ffffffff81049ee5>] irq_exit+0x95/0xa0 <4>[ 7290.415852] [<ffffffff8100e547>] do_IRQ+0x77/0xf0 <4>[ 7290.415869] [<ffffffff8100c7d3>] ret_from_intr+0x0/0xf <4>[ 7290.415883] <EOI> [<ffffffff81234efa>] ? acpi_idle_enter_bm+0x270/0x2a5 <4>[ 7290.415911] [<ffffffff81234f04>] ? acpi_idle_enter_bm+0x27a/0x2a5 <4>[ 7290.415931] [<ffffffff81234efa>] ? acpi_idle_enter_bm+0x270/0x2a5 <4>[ 7290.415952] [<ffffffff812c11f3>] ? cpuidle_idle_call+0x93/0xf0 <4>[ 7290.415971] [<ffffffff8100b0d7>] ? cpu_idle+0xa7/0x110 <4>[ 7290.415989] [<ffffffff8137b3d5>] ? rest_init+0x75/0x80 <4>[ 7290.416007] [<ffffffff8158cd0a>] ? start_kernel+0x3a7/0x3b3 <4>[ 7290.416026] [<ffffffff8158c315>] ? x86_64_start_reservations+0x125/0x129 <4>[ 7290.416047] [<ffffffff8158c3fd>] ? x86_64_start_kernel+0xe4/0xeb Reported-by: Maxim Levitsky <maximlevitsky@gmail.com> Tested-by: Maxim Levitsky <maximlevitsky@gmail.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> CC: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-01-08e1000e: fix and commonize code for setting the receive address registersBruce Allan
Fix e1000e_rar_set() to flush consecutive register writes to avoid write combining which some parts cannot handle. Update e1000e_init_rx_addrs() to call the fixed e1000e_rar_set() instead of duplicating code. Also change e1000e_rar_set() to _not_ set the Address Valid bit if the MAC address is all zeros. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-08e1000e: e1000e_enable_tx_pkt_filtering() returns wrong valueBruce Allan
e1000e_enable_tx_pkt_filtering() will return a non-zero value if the driver fails to enable the manageability interface on the host for any reason; instead it should retun zero to indicate filtering has been disabled. Also provide a single exit point for the function. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-08e1000e: perform 10/100 adaptive IFS only on parts that support itBruce Allan
Adaptive IFS which involves writing to the Adaptive IFS Throttle register was being done for all devices supported by the driver even though it is not supported (i.e. the register doesn't even exist) on some devices. The feature is supported on 8257x/82583 and ICH/PCH based devices, but not on ESB2. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-08e1000e: don't accumulate PHY statistics on PHY read failureBruce Allan
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-08e1000e: call pci_save_state() after pci_restore_state()Bruce Allan
Due to a change in pci_restore_state()[1] which clears the saved_state flag, the driver should call pci_save_state() to set the flag once again to avoid issues with EEH (same fix that recently was submitted for ixgbe). [1] commmit 4b77b0a2ba27d64f58f16d8d4d48d8319dda36ff Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-08netxen: update version to 4.0.72Amit Kumar Salecha
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-08netxen: fix set mac addrAmit Kumar Salecha
o If tx and rx resources are not available, during set mac request. Then this request wont be passed to firmware and it will be added to driver mac list and will never make it to firmware. So if resources are not available, don't add it to driver mac list. Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-08netxen: fix smatch warningAmit Kumar Salecha
o Fix pointless assignments Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-08netxen: fix tx ring memory leakAmit Kumar Salecha
o While unloading driver or resetting the context, tx ring was not getting free. Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-07TI DaVinci EMAC: Handle emac module clock correctly.Sriram
In the driver probe function the emac module clock needs to be enabled before calling register_netdev(). As soon as the device is registered the driver get_stats function can be invoked by the core - the module clock must be switched on to be able to read from stats registers. Also explicitly call matching clk_disable for failure conditions in probe function. Signed-off-by: Sriramakrishnan <srk@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-07dmfe/tulip: Let dmfe handle DM910x except for SPARC on-board chipsBen Hutchings
The Davicom DM9100 and DM9102 chips are used on the motherboards of some SPARC systems (supported by the tulip driver) and also in PCI expansion cards (supported by the dmfe driver). There is no difference in the PCI device ids for the two different configurations, so these drivers both claim the device ids. However, it is possible to distinguish the two configurations by the presence of Open Firmware properties for them, so we do that. Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Grant Grundler <grundler@parisc-linux.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-07ixgbe: Fix compiler warning about variable being used uninitializedPJ Waskiewicz
tc is still throwing a warning that is could be used uninitialized. This fixes it, and properly formats the device ID checks for the use of this variable. Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-07mv643xx_eth: don't include cache padding in rx desc buffer sizeSaeed Bishara
If NET_SKB_PAD is not a multiple of the cache line size, mv643xx_eth allocates a couple of extra bytes at the start of each receive buffer to make the data payload end up on a cache line boundary. These extra bytes are skb_reserve()'d before DMA mapping, so they should not be included in the DMA map byte count (as the mapping is done starting at skb->data), nor should they be included in the receive descriptor buffer size field, or the hardware can end up DMAing beyond the end of the buffer, which can happen if someone sends us a larger-than-MTU sized packet. This problem was introduced in commit 7fd96ce47ff ("mv643xx_eth: rework receive skb cache alignment", May 6 2009), but hasn't appeared to be problematic so far, probably as the main users of mv643xx_eth all have NET_SKB_PAD == L1_CACHE_BYTES. Signed-off-by: Saeed Bishara <saeed@marvell.com> Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-07NET: atlx, fix memory leakJiri Slaby
Stanse found a memory leak in atl2_get_eeprom. eeprom_buff is not freed/assigned on all paths. Fix that. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Cc: Jay Cliburn <jcliburn@gmail.com> Cc: Chris Snook <chris.snook@gmail.com> Cc: Jie Yang <jie.yang@atheros.com> Cc: atl1-devel@lists.sourceforge.net Cc: "David S. Miller" <davem@davemloft.net> Cc: netdev@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-07pcmcia: ncmlan_cs: remove odd bracketAlexander Beregalov
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-07cs89x0: Always report failure to request interruptMark Brown
A failure on request_irq() is always fatal but unlike other fatal errors it's only reported to the user if net_debug is set. Make the diagnostic unconditional and raise the priority so that errors are more obvious to the user. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-07hso: fixed missing newlinesJan Dumon
Fixed missing newlines in calls to dev_warn & dev_err. Signed-off-by: Jan Dumon <j.dumon@option.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-07hso: Fix for 5 sec timeouts with v2.x firmwareJan Dumon
Don't send flow control settings to any port other than the modem port. Older firmware ignored this request but did sent a reply. Newer firmware just ignores it without reply and causes a 5 second timeout every time a port (except for the modem port) is opened or if tiocm settings are changed. Signed-off-by: Jan Dumon <j.dumon@option.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-07hso: Attempt to recover from usb bus errorsJan Dumon
Attempt to reset the usb device when we receive usb bus errors. Signed-off-by: Jan Dumon <j.dumon@option.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-07hso: don't change the state of a closed portJan Dumon
Don't change the state of a port if it's not open. This fixes an issue where a port sometimes has to be opened twice before data can be received. Signed-off-by: Jan Dumon <j.dumon@option.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-07hso: Fix for endian issues on big endian machinesJan Dumon
Some fields are always little endian and have to be converted on big endian machines. Signed-off-by: Jan Dumon <j.dumon@option.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-07hso: Add Vendor/Product ID's for new devicesJan Dumon
Add product ID's for new devices. Signed-off-by: Jan Dumon <j.dumon@option.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-06pcnet_cs: add cis of KTI PE520 pcmcia network cardKen Kawasaki
pcnet_cs,serial_cs: add cis of KTI PE520 pcmcia network card, and serial card(Sierra Wireless AC860). Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-06ucc_geth: Fix the wrong the Rx/Tx FIFO sizeDave Liu
current the Rx/Tx FIFO size settings cause problem when four UEC ethernets work simultaneously. eg: GETH1, UEM-J15, GETH2, UEC-J5 on 8569MDS board $ ifconfig eth0 10.193.20.166 $ ifconfig eth1 10.193.20.167 $ ifconfig eth2 10.193.20.168 then $ ifconfig eth3 10.193.20.169 The fourth ethernet will cause all of interface broken, you cann't ping successfully any more. The patch fix this issue for MPC8569 Rev1.0 and Rev2.0 Signed-off-by: Dave Liu <daveliu@freescale.com> Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-05rt2x00: Properly request tx headroom for alignment operations.Gertjan van Wingerde
Current rt2x00 drivers may result in a "ieee80211_tx_status: headroom too small" error message when a frame needs to be properly aligned before transmitting it. This is because the space needed to ensure proper alignment isn't requested from mac80211. Fix this by adding sufficient amount of alignment space to the amount of headroom requested for TX frames. Reported-by: David Ellingsworth <david@identd.dyndns.org> Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <ivdoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-01-05rt2x00: Fix LED configuration setting for rt2800.Gertjan van Wingerde
rt2800_blink_set uses an illegal value to set the LED_CFG_G_LED_MODE field of the LED_CFG register. This field is only 2 bits large, so should be initialized with value that fits. Use default value from the vendor driver. Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-01-05rt2x00: use correct headroom for transmissionPavel Roskin
Use rt2x00dev->ops->extra_tx_headroom, not rt2x00dev->hw->extra_tx_headroom in the tx code, as the later may include other headroom not to be used in the chipset driver. Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-01-04ath5k: Fix eeprom checksum check for custom sized eepromsLuis R. Rodriguez
Commit 8bf3d79bc401ca417ccf9fc076d3295d1a71dbf5 enabled EEPROM checksum checks to avoid bogus bug reports but failed to address updating the code to consider devices with custom EEPROM sizes. Devices with custom sized EEPROMs have the upper limit size stuffed in the EEPROM. Use this as the upper limit instead of the static default size. In case of a checksum error also provide back the max size and whether or not this was the default size or a custom one. If the EEPROM is busted we add a failsafe check to ensure we don't loop forever or try to read bogus areas of hardware. This closes bug 14874 http://bugzilla.kernel.org/show_bug.cgi?id=14874 Cc: stable@kernel.org Cc: David Quan <david.quan@atheros.com> Cc: Stephen Beahm <stephenbeahm@comcast.net> Reported-by: Joshua Covington <joshuacov@googlemail.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-01-04zd1211rw: Fix multicast filtering.Benoit Papillault
If multicast parameter (as returned by zd_op_prepare_multicast) has changed, no bit in changed_flags is set. To handle this situation, we do not return if changed_flags is 0. If we do so, we will have some issue with IPv6 which uses multicast for link layer address resolution. Signed-off-by: Benoit Papillault <benoit.papillault@free.fr> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-01-04iwl: off by one bugDan Carpenter
tid is used as an array offset. agg = &priv->stations[sta_id].tid[tid].agg; iwl4965_tx_status_reply_tx(priv, agg, tx_resp, txq_id, index); It should be limitted to MAX_TID_COUNT - 1; struct iwl_tid_data tid[MAX_TID_COUNT]; regards, dan carpenter Signed-off-by: Dan Carpenter <error27@gmail.com> CC: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-01-04mwl8k: fix configure_filter() memory leak on errorLennert Buytenhek
If there was an error acquiring the firmware lock in mwl8k_configure_filter(), we would end up leaking the multicast command packet prepared by mwl8k_prepare_multicast(). Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-01-04ath9k: fix ito64Ming Lei
The unit of sizeof() is byte instead of bit, so fix it. The patch can fix debug output of some dma_addr_t variables. Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-01-04ath9k: Fix Kconfig depends for ATH9K_DEBUGFSDominik Geyer
Add missing DEBUG_FS dependency for ATH9K_DEBUGFS in ath9k's Kconfig. Signed-off-by: Dominik D. Geyer <dominik.geyer@gmx.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-01-03netxen: fix ethtool link testSucheta Chakraborty
o Fix ethtool link test for NX3031 chip. o Remove unused code from phy interrupt callback Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-03netxen: fix ethtool register dumpSucheta Chakraborty
o Dump registers such as tx ring and rx ring counter, firmware state, niu regs, etc. which can be useful for debugging purpose. Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-03rrunner: fix buffer overflowDan Carpenter
tx_skbuff is define as: struct sk_buff *tx_skbuff[TX_RING_ENTRIES]; EVT_RING_ENTRIES is 64 and TX_RING_ENTRIES is 32. This function is in a error path so that's why it wasn't noticed. Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-03broadcom: Fix &&/|| confusion in bcm54xx_adjust_rxrefclk()roel kluin
This always evaluates to true. Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3-18-g5258 (git 2.32.0) at 2024-12-17 04:45:01 +0000