aboutsummaryrefslogtreecommitdiff
path: root/drivers/net
AgeCommit message (Collapse)Author
2014-05-22bonding: Send ALB learning packets using the right sourceVlad Yasevich
ALB learning packets are currentlyalways sent using the slave mac address for all vlans configured on top of bond. This is not always correct, as vlans may change their mac address. This patch introduced a concept of strict matching where the source of learning packets can either strictly match the address passed in, or it can determine a more correct address to use. There are 3 casese to consider: 1) Switchover. In this case, we have a new active slave and we need tell the switch about all addresses available on the slave. 2) Monitor. We'll periodically refresh learning info for all slaves. In this case, we refresh all addresses for current active, and just the slave address for other slaves. 3) Teaching of disabled adddress. This happens as part of the failover and in this case, we alwyas to use just the address provided. CC: Jay Vosburgh <j.vosburgh@gmail.com> CC: Veaceslav Falico <vfalico@gmail.com> CC: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: Vlad Yasevich <vyasevic@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-22bonding: Don't assume 802.1Q when sending alb learning packets.Vlad Yasevich
TLB/ALB learning packets always assume 802.1Q vlan protocol, but that is no longer the case since we now have support for Q-in-Q on top of bonding. Pass the vlan protocol to alb_send_lp_vid() so that the packets are properly tagged. CC: Jay Vosburgh <j.vosburgh@gmail.com> CC: Veaceslav Falico <vfalico@gmail.com> CC: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: Vlad Yasevich <vyasevic@redhat.com> Acked-by: Veaceslav Falico <vfalico@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-22Merge tag 'linux-can-fixes-for-3.15-20140521' of ↵David S. Miller
git://gitorious.org/linux-can/linux-can Marc Kleine-Budde says: ==================== pull-request: can 2014-05-21 this is a pull request for net/master, for the v3.15 release cycle, with a single patch. Christopher R. Baker found a use after free during unloading of the peak_pci driver. This is fixes in a patch by Stephane Grosjean. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-22stmmac: Remove unbalanced clk_disable callHans de Goede
The stmmac_open call was calling clk_disable_unprepare on phy init failure, but it never calls clk_prepare_enable, this causes a WARN_ON in the clk framework to trigger if for some reason phy init fails. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Acked-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-21can: peak_pci: prevent use after free at netdev removalStephane Grosjean
As remarked by Christopher R. Baker in his post at http://marc.info/?l=linux-can&m=139707295706465&w=2 there's a possibility for an use after free condition at device removal. This simplified patch introduces an additional variable to prevent the issue. Thanks for catching this. Cc: linux-stable <stable@vger.kernel.org> Reported-by: Christopher R. Baker <cbaker@rec.ri.cmu.edu> Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2014-05-19can: c_can: remove obsolete STRICT_FRAME_ORDERING Kconfig optionOliver Hartkopp
In 2b9aecdce2 ("can: c_can: Disable rx split as workaround") a new Kconfig option was introduced as a workaround. The tests performed by Alexander Stein confirmed this option to be obsolete with all the other cleanups and fixes that had been discussed that time: http://marc.info/?l=linux-can&m=139746476821294&w=2 Both (author and tester) agreed to remove this Kconfig option again: http://marc.info/?l=linux-can&m=139883820714229&w=2 As some more cleanups took place since then a simple revert is not possible. This patch removes the entire option as it would behave when disabled. Further beautification’s can be done later. Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Tested-by: Alexander Stein <alexander.stein@systec-electronic.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2014-05-18bnx2x: Convert return 0 to return rcJoe Perches
These "return 0;" uses seem wrong as there are rc variables where error return values are set but unused. Signed-off-by: Joe Perches <joe@perches.com> Acked-by: Dmitry Kravkov <Dmitry.Kravkov@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-16bonding: Fix alb mode to only use first level vlans.Vlad Yasevich
ALB/TLB learning packets use all vlans configured on top of the bond. This ends up being incorrect if we have a stack of vlans on top of the bond. ALB/TLB should only use first level/outer most vlans in its announcements. Signed-off-by: Vlad Yasevich <vyasevic@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-16bonding: Fix stacked device detection in arp monitoringVlad Yasevich
Prior to commit fbd929f2dce460456807a51e18d623db3db9f077 bonding: support QinQ for bond arp interval the arp monitoring code allowed for proper detection of devices stacked on top of vlans. Since the above commit, the code can still detect a device stacked on top of single vlan, but not a device stacked on top of Q-in-Q configuration. The search will only set the inner vlan tag if the route device is the vlan device. However, this is not always the case, as it is possible to extend the stacked configuration. With this patch it is possible to provision devices on top Q-in-Q vlan configuration that should be used as a source of ARP monitoring information. For example: ip link add link bond0 vlan10 type vlan proto 802.1q id 10 ip link add link vlan10 vlan100 type vlan proto 802.1q id 100 ip link add link vlan100 type macvlan Note: This patch limites the number of stacked VLANs to 2, just like before. The original, however had another issue in that if we had more then 2 levels of VLANs, we would end up generating incorrectly tagged traffic. This is no longer possible. Fixes: fbd929f2dce460456807a51e18d623db3db9f077 (bonding: support QinQ for bond arp interval) CC: Jay Vosburgh <j.vosburgh@gmail.com> CC: Veaceslav Falico <vfalico@redhat.com> CC: Andy Gospodarek <andy@greyhouse.net> CC: Ding Tianhong <dingtianhong@huawei.com> CC: Patric McHardy <kaber@trash.net> Signed-off-by: Vlad Yasevich <vyasevic@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-16macvlan: Fix lockdep warnings with stacked macvlan devicesVlad Yasevich
Macvlan devices try to avoid stacking, but that's not always successfull or even desired. As an example, the following configuration is perefectly legal and valid: eth0 <--- macvlan0 <---- vlan0.10 <--- macvlan1 However, this configuration produces the following lockdep trace: [ 115.620418] ====================================================== [ 115.620477] [ INFO: possible circular locking dependency detected ] [ 115.620516] 3.15.0-rc1+ #24 Not tainted [ 115.620540] ------------------------------------------------------- [ 115.620577] ip/1704 is trying to acquire lock: [ 115.620604] (&vlan_netdev_addr_lock_key/1){+.....}, at: [<ffffffff815df49c>] dev_uc_sync+0x3c/0x80 [ 115.620686] but task is already holding lock: [ 115.620723] (&macvlan_netdev_addr_lock_key){+.....}, at: [<ffffffff815da5be>] dev_set_rx_mode+0x1e/0x40 [ 115.620795] which lock already depends on the new lock. [ 115.620853] the existing dependency chain (in reverse order) is: [ 115.620894] -> #1 (&macvlan_netdev_addr_lock_key){+.....}: [ 115.620935] [<ffffffff810d57f2>] lock_acquire+0xa2/0x130 [ 115.620974] [<ffffffff816f62e7>] _raw_spin_lock_nested+0x37/0x50 [ 115.621019] [<ffffffffa07296c3>] vlan_dev_set_rx_mode+0x53/0x110 [8021q] [ 115.621066] [<ffffffff815da557>] __dev_set_rx_mode+0x57/0xa0 [ 115.621105] [<ffffffff815da5c6>] dev_set_rx_mode+0x26/0x40 [ 115.621143] [<ffffffff815da6be>] __dev_open+0xde/0x140 [ 115.621174] [<ffffffff815da9ad>] __dev_change_flags+0x9d/0x170 [ 115.621174] [<ffffffff815daaa9>] dev_change_flags+0x29/0x60 [ 115.621174] [<ffffffff815e7f11>] do_setlink+0x321/0x9a0 [ 115.621174] [<ffffffff815ea59f>] rtnl_newlink+0x51f/0x730 [ 115.621174] [<ffffffff815e6e75>] rtnetlink_rcv_msg+0x95/0x250 [ 115.621174] [<ffffffff81608b19>] netlink_rcv_skb+0xa9/0xc0 [ 115.621174] [<ffffffff815e6dca>] rtnetlink_rcv+0x2a/0x40 [ 115.621174] [<ffffffff81608150>] netlink_unicast+0xf0/0x1c0 [ 115.621174] [<ffffffff8160851f>] netlink_sendmsg+0x2ff/0x740 [ 115.621174] [<ffffffff815bc9db>] sock_sendmsg+0x8b/0xc0 [ 115.621174] [<ffffffff815bd4b9>] ___sys_sendmsg+0x369/0x380 [ 115.621174] [<ffffffff815bdbb2>] __sys_sendmsg+0x42/0x80 [ 115.621174] [<ffffffff815bdc02>] SyS_sendmsg+0x12/0x20 [ 115.621174] [<ffffffff816ffd69>] system_call_fastpath+0x16/0x1b [ 115.621174] -> #0 (&vlan_netdev_addr_lock_key/1){+.....}: [ 115.621174] [<ffffffff810d4d43>] __lock_acquire+0x1773/0x1a60 [ 115.621174] [<ffffffff810d57f2>] lock_acquire+0xa2/0x130 [ 115.621174] [<ffffffff816f62e7>] _raw_spin_lock_nested+0x37/0x50 [ 115.621174] [<ffffffff815df49c>] dev_uc_sync+0x3c/0x80 [ 115.621174] [<ffffffffa0696d2a>] macvlan_set_mac_lists+0xca/0x110 [macvlan] [ 115.621174] [<ffffffff815da557>] __dev_set_rx_mode+0x57/0xa0 [ 115.621174] [<ffffffff815da5c6>] dev_set_rx_mode+0x26/0x40 [ 115.621174] [<ffffffff815da6be>] __dev_open+0xde/0x140 [ 115.621174] [<ffffffff815da9ad>] __dev_change_flags+0x9d/0x170 [ 115.621174] [<ffffffff815daaa9>] dev_change_flags+0x29/0x60 [ 115.621174] [<ffffffff815e7f11>] do_setlink+0x321/0x9a0 [ 115.621174] [<ffffffff815ea59f>] rtnl_newlink+0x51f/0x730 [ 115.621174] [<ffffffff815e6e75>] rtnetlink_rcv_msg+0x95/0x250 [ 115.621174] [<ffffffff81608b19>] netlink_rcv_skb+0xa9/0xc0 [ 115.621174] [<ffffffff815e6dca>] rtnetlink_rcv+0x2a/0x40 [ 115.621174] [<ffffffff81608150>] netlink_unicast+0xf0/0x1c0 [ 115.621174] [<ffffffff8160851f>] netlink_sendmsg+0x2ff/0x740 [ 115.621174] [<ffffffff815bc9db>] sock_sendmsg+0x8b/0xc0 [ 115.621174] [<ffffffff815bd4b9>] ___sys_sendmsg+0x369/0x380 [ 115.621174] [<ffffffff815bdbb2>] __sys_sendmsg+0x42/0x80 [ 115.621174] [<ffffffff815bdc02>] SyS_sendmsg+0x12/0x20 [ 115.621174] [<ffffffff816ffd69>] system_call_fastpath+0x16/0x1b [ 115.621174] other info that might help us debug this: [ 115.621174] Possible unsafe locking scenario: [ 115.621174] CPU0 CPU1 [ 115.621174] ---- ---- [ 115.621174] lock(&macvlan_netdev_addr_lock_key); [ 115.621174] lock(&vlan_netdev_addr_lock_key/1); [ 115.621174] lock(&macvlan_netdev_addr_lock_key); [ 115.621174] lock(&vlan_netdev_addr_lock_key/1); [ 115.621174] *** DEADLOCK *** [ 115.621174] 2 locks held by ip/1704: [ 115.621174] #0: (rtnl_mutex){+.+.+.}, at: [<ffffffff815e6dbb>] rtnetlink_rcv+0x1b/0x40 [ 115.621174] #1: (&macvlan_netdev_addr_lock_key){+.....}, at: [<ffffffff815da5be>] dev_set_rx_mode+0x1e/0x40 [ 115.621174] stack backtrace: [ 115.621174] CPU: 3 PID: 1704 Comm: ip Not tainted 3.15.0-rc1+ #24 [ 115.621174] Hardware name: Hewlett-Packard HP xw8400 Workstation/0A08h, BIOS 786D5 v02.38 10/25/2010 [ 115.621174] ffffffff82339ae0 ffff880465f79568 ffffffff816ee20c ffffffff82339ae0 [ 115.621174] ffff880465f795a8 ffffffff816e9e1b ffff880465f79600 ffff880465b019c8 [ 115.621174] 0000000000000001 0000000000000002 ffff880465b019c8 ffff880465b01230 [ 115.621174] Call Trace: [ 115.621174] [<ffffffff816ee20c>] dump_stack+0x4d/0x66 [ 115.621174] [<ffffffff816e9e1b>] print_circular_bug+0x200/0x20e [ 115.621174] [<ffffffff810d4d43>] __lock_acquire+0x1773/0x1a60 [ 115.621174] [<ffffffff810d3172>] ? trace_hardirqs_on_caller+0xb2/0x1d0 [ 115.621174] [<ffffffff810d57f2>] lock_acquire+0xa2/0x130 [ 115.621174] [<ffffffff815df49c>] ? dev_uc_sync+0x3c/0x80 [ 115.621174] [<ffffffff816f62e7>] _raw_spin_lock_nested+0x37/0x50 [ 115.621174] [<ffffffff815df49c>] ? dev_uc_sync+0x3c/0x80 [ 115.621174] [<ffffffff815df49c>] dev_uc_sync+0x3c/0x80 [ 115.621174] [<ffffffffa0696d2a>] macvlan_set_mac_lists+0xca/0x110 [macvlan] [ 115.621174] [<ffffffff815da557>] __dev_set_rx_mode+0x57/0xa0 [ 115.621174] [<ffffffff815da5c6>] dev_set_rx_mode+0x26/0x40 [ 115.621174] [<ffffffff815da6be>] __dev_open+0xde/0x140 [ 115.621174] [<ffffffff815da9ad>] __dev_change_flags+0x9d/0x170 [ 115.621174] [<ffffffff815daaa9>] dev_change_flags+0x29/0x60 [ 115.621174] [<ffffffff811e1db1>] ? mem_cgroup_bad_page_check+0x21/0x30 [ 115.621174] [<ffffffff815e7f11>] do_setlink+0x321/0x9a0 [ 115.621174] [<ffffffff810d394c>] ? __lock_acquire+0x37c/0x1a60 [ 115.621174] [<ffffffff815ea59f>] rtnl_newlink+0x51f/0x730 [ 115.621174] [<ffffffff815ea169>] ? rtnl_newlink+0xe9/0x730 [ 115.621174] [<ffffffff815e6e75>] rtnetlink_rcv_msg+0x95/0x250 [ 115.621174] [<ffffffff810d329d>] ? trace_hardirqs_on+0xd/0x10 [ 115.621174] [<ffffffff815e6dbb>] ? rtnetlink_rcv+0x1b/0x40 [ 115.621174] [<ffffffff815e6de0>] ? rtnetlink_rcv+0x40/0x40 [ 115.621174] [<ffffffff81608b19>] netlink_rcv_skb+0xa9/0xc0 [ 115.621174] [<ffffffff815e6dca>] rtnetlink_rcv+0x2a/0x40 [ 115.621174] [<ffffffff81608150>] netlink_unicast+0xf0/0x1c0 [ 115.621174] [<ffffffff8160851f>] netlink_sendmsg+0x2ff/0x740 [ 115.621174] [<ffffffff815bc9db>] sock_sendmsg+0x8b/0xc0 [ 115.621174] [<ffffffff8119d4af>] ? might_fault+0x5f/0xb0 [ 115.621174] [<ffffffff8119d4f8>] ? might_fault+0xa8/0xb0 [ 115.621174] [<ffffffff8119d4af>] ? might_fault+0x5f/0xb0 [ 115.621174] [<ffffffff815cb51e>] ? verify_iovec+0x5e/0xe0 [ 115.621174] [<ffffffff815bd4b9>] ___sys_sendmsg+0x369/0x380 [ 115.621174] [<ffffffff816faa0d>] ? __do_page_fault+0x11d/0x570 [ 115.621174] [<ffffffff810cfe9f>] ? up_read+0x1f/0x40 [ 115.621174] [<ffffffff816fab04>] ? __do_page_fault+0x214/0x570 [ 115.621174] [<ffffffff8120a10b>] ? mntput_no_expire+0x6b/0x1c0 [ 115.621174] [<ffffffff8120a0b7>] ? mntput_no_expire+0x17/0x1c0 [ 115.621174] [<ffffffff8120a284>] ? mntput+0x24/0x40 [ 115.621174] [<ffffffff815bdbb2>] __sys_sendmsg+0x42/0x80 [ 115.621174] [<ffffffff815bdc02>] SyS_sendmsg+0x12/0x20 [ 115.621174] [<ffffffff816ffd69>] system_call_fastpath+0x16/0x1b Fix this by correctly providing macvlan lockdep class. Signed-off-by: Vlad Yasevich <vyasevic@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-16xen-netback: fix race between napi_complete() and interrupt handlerDavid Vrabel
When the NAPI budget was not all used, xenvif_poll() would call napi_complete() /after/ enabling the interrupt. This resulted in a race between the napi_complete() and the napi_schedule() in the interrupt handler. The use of local_irq_save/restore() avoided by race iff the handler is running on the same CPU but not if it was running on a different CPU. Fix this properly by calling napi_complete() before reenabling interrupts (in the xenvif_napi_schedule_or_enable_irq() call). Signed-off-by: David Vrabel <david.vrabel@citrix.com> Acked-by: Wei Liu <wei.liu2@citrix.com> Acked-by: Ian Campbell <ian.campbell@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-16Merge branch 'for-davem' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless John W. Linville says: ==================== pull request: wireless 2014-05-15 Please pull this batch of fixes for the 3.15 stream... For the mac80211 bits, Johannes says: "One fix is to get better VHT performance and the other fixes tracing garbage or other potential issues with the interface name tracing." And... "This has a fix from Emmanuel for a problem I failed to fix - when association is in progress then it needs to be cancelled while suspending (I had fixed the same for authentication). Also included a fix from myself for a userspace API problem that hit the iw tool and a fix to the remain-on-channel framework." For the iwlwifi bits, Emmanuel says: "Alex fixes the scan by disabling the fragmented scan. David prevents scan offload while associated, the firmware seems not to like it. I fix a stupid bug I made in BT Coex, and fix a bad #ifdef clause in rate scaling. Along with that there is a fix for a NULL pointer exception that can happen if we load the driver and our ISR gets called because the interrupt line is shared. The fix has been tested by the reporter." And... "We have here a fix from David Spinadel that makes a previous fix more complete, and an off-by-one issue fixed by Eliad in the same area. I fix the monitor that broke on the way." Beyond that... Daniel Kim's one-liner fixes a brcmfmac regression caused by a typo in an earlier commit.. Rajkumar Manoharan fixes an ath9k oops reported by David Herrmann. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-16net: phy: resume phydev when going to RESUMINGZhangfei Gao
With commit be9dad1f9f26604fb ("net: phy: suspend phydev when going to HALTED"), an unused PHY device will be put in a low-power mode using BMCR_PDOWN. Some Ethernet drivers might be calling phy_start() and phy_stop() from ndo_open and ndo_close() respectively, while calling phy_connect() and phy_disconnect() from probe and remove. In such a case, the PHY will be powered down during the phy_stop() call, but will fail to be powered up in phy_start(). This patch fixes this scenario. Signed-off-by: Jiancheng Xue <xuejiancheng@huawei.com> Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-16net/mlx4_core: Add UPDATE_QP SRIOV wrapper supportMatan Barak
This patch adds UPDATE_QP SRIOV wrapper support. The mechanism is a general one, but currently only source MAC index changes are allowed for VFs. Signed-off-by: Matan Barak <matanb@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-15bonding: fix out of range parameters for bond_intmax_tblNikolay Aleksandrov
I've missed to add a NULL entry to the bond_intmax_tbl when I introduced it with the conversion of arp_interval so add it now. CC: Jay Vosburgh <j.vosburgh@gmail.com> CC: Veaceslav Falico <vfalico@gmail.com> CC: Andy Gospodarek <andy@greyhouse.net> Fixes: 7bdb04ed0dbf ("bonding: convert arp_interval to use the new option API") Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com> Acked-by: Veaceslav Falico <vfalico@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-15xen-netback: Fix grant ref resolution in RX pathZoltan Kiss
The original series for reintroducing grant mapping for netback had a patch [1] to handle receiving of packets from an another VIF. Grant copy on the receiving side needs the grant ref of the page to set up the op. The original patch assumed (wrongly) that the frags array haven't changed. In the case reported by Sander, the sending guest sent a packet where the linear buffer and the first frag were under PKT_PROT_LEN (=128) bytes. xenvif_tx_submit() then pulled up the linear area to 128 bytes, and ditched the first frag. The receiving side had an off-by-one problem when gathered the grant refs. This patch fixes that by checking whether the actual frag's page pointer is the same as the page in the original frag list. It can handle any kind of changes on the original frags array, like: - removing granted frags from the array at any point - adding local pages to the frags list anywhere - reordering the frags It's optimized to the most common case, when there is 1:1 relation between the frags and the list, plus works optimal when frags are removed from the end or the beginning. [1]: 3e2234: xen-netback: Handle foreign mapped pages on the guest RX path Reported-by: Sander Eikelenboom <linux@eikelenboom.it> Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com> Acked-by: Ian Campbell <ian.campbell@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-15net: phy: Don't call phy_resume if phy_init_hw failedGuenter Roeck
After the call to phy_init_hw failed in phy_attach_direct, phy_detach is called to detach the phy device from its network device. If the attached driver is a generic phy driver, this also detaches the driver. Subsequently phy_resume is called, which assumes without checking that a driver is attached to the device. This will result in a crash such as Unable to handle kernel paging request for data at address 0xffffffffffffff90 Faulting instruction address: 0xc0000000003a0e18 Oops: Kernel access of bad area, sig: 11 [#1] ... NIP [c0000000003a0e18] .phy_attach_direct+0x68/0x17c LR [c0000000003a0e6c] .phy_attach_direct+0xbc/0x17c Call Trace: [c0000003fc0475d0] [c0000000003a0e6c] .phy_attach_direct+0xbc/0x17c (unreliable) [c0000003fc047670] [c0000000003a0ff8] .phy_connect_direct+0x28/0x98 [c0000003fc047700] [c0000000003f0074] .of_phy_connect+0x4c/0xa4 Only call phy_resume if phy_init_hw was successful. Signed-off-by: Guenter Roeck <linux@roeck-us.net> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-15Altera TSE: Disable Multicast filtering to workaround problemVince Bridgers
This patch disables multicast hash filtering if present in the hardware and uses promiscuous mode instead until the problem with multicast filtering has been debugged, integrated and tested. Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-15Altera TSE: Fix sparse errors and warningsVince Bridgers
This patch fixes the many sparse errors and warnings contained in the initial submission of the Altera Triple Speed Ethernet driver, and a few minor cppcheck warnings. Changes are tested on ARM and NIOS2 example designs, and compile tested against multiple architectures. Typical issues addressed were as follows: altera_tse_ethtool.c:136:19: warning: incorrect type in argument 1 (different address spaces) altera_tse_ethtool.c:136:19: expected void const volatile [noderef] <asn:2>*addr altera_tse_ethtool.c:136:19: got unsigned int *<noident> ... altera_sgdma.c:129:31: warning: cast removes address space of expression Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-15Merge branch 'master' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
2014-05-14ath9k_htc: Stop ANI before doing hw_resetRajkumar Manoharan
During remain on channel request, ANI worker thread is not stopped before doing hw reset. This is causing kernel crash in hw_per_calibration. This change ensures that ANI is stopped before doing chip reset and it will be rescheduled later when the chip is configured back to home channel and having valid bss. Reported-by: David Herrmann <dh.herrmann@gmail.com> Tested-by: David Herrmann <dh.herrmann@gmail.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-05-14be2net: enable interrupts in EEH resumeKalesh AP
On some BE3 FW versions, after a HW reset, interrupts will remain disabled for each function. So, explicitly enable the interrupts in the eeh_resume handler, else after an eeh recovery interrupts wouldn't work. Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com> Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-14jme: Fix unmap loop counting error:Neil Horman
In my recent fix (76a691d0a: fix dma unmap warning), Ben Hutchings noted that my loop count was incorrect. Where j started at startidx, it should have started at zero, and gone on for count entries, not to endidx. Additionally, a DMA resource exhaustion should drop the frame and (for now), return NETDEV_TX_OK, not NETEV_TX_BUSY. This patch fixes both of those issues: Signed-off-by: Neil Horman <nhorman@tuxdriver.com> CC: Ben Hutchings <ben@decadent.org.uk> CC: "David S. Miller" <davem@davemloft.net> CC: Guo-Fu Tseng <cooldavid@cooldavid.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-13Merge branch 'for-john' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
2014-05-13iwlwifi: mvm: prevent sched scan while not idleDavid Spinadel
Prevent sched scan while not idle (including during association or in AP mode) instead of while associated only. This fixes my previous commit which was incomplete: commit bd5e4744a6ca64299b57a2682c720d00a475a734 Author: David Spinadel <david.spinadel@intel.com> Date: Thu Apr 24 13:15:29 2014 +0300 iwlwifi: mvm: do no sched scan while associated Currently the FW doesn't support sched scan while associated, Prevent it. Signed-off-by: David Spinadel <david.spinadel@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2014-05-13iwlwifi: mvm: fix off-by-one in scan channels configurationEliad Peller
tail should be equal to the last valid index, so decrease it by one. This error causes in "a gap" in some cases (as well as some possible out-of-bound write), finally resulting in ucode assertion. Signed-off-by: Eliad Peller <eliadx.peller@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2014-05-12sfc: fix calling of free_irq with already free vectorNikolay Aleksandrov
If the sfc driver is in legacy interrupt mode (either explicitly by using interrupt_mode module param or by falling back to it) it will hit a warning at kernel/irq/manage.c because it will try to free an irq which wasn't allocated by it in the first place because the MSI(X) irqs are zero and it'll try to free them unconditionally. So fix it by checking if we're in legacy mode and freeing the appropriate irqs. CC: Zenghui Shi <zshi@redhat.com> CC: Ben Hutchings <ben@decadent.org.uk> CC: <linux-net-drivers@solarflare.com> CC: Shradha Shah <sshah@solarflare.com> CC: David S. Miller <davem@davemloft.net> Fixes: 1899c111a535 ("sfc: Fix IRQ cleanup in case of a probe failure") Reported-by: Zenghui Shi <zshi@redhat.com> Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com> Acked-by: Shradha Shah <sshah@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-12macvlan: Don't propagate IFF_ALLMULTI changes on down interfaces.Peter Christensen
Clearing the IFF_ALLMULTI flag on a down interface could cause an allmulti overflow on the underlying interface. Attempting the set IFF_ALLMULTI on the underlying interface would cause an error and the log message: "allmulti touches root, set allmulti failed." Signed-off-by: Peter Christensen <pch@ordbogen.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-12brcmfmac: Fix iovar 'bw_cap' set command failureDaniel Kim
Fix iovar 'bw_cap' set command failure introduced by commit ff3b0fba6f25555ef59c55d138a467d0f81d82d7 Author: Arend van Spriel <arend@broadcom.com> Date: Sat Mar 15 12:00:57 2014 +0100 brcmfmac: fallback to mimo_bw_cap for older firmwares This resulted in disabling 20MHz operation in the firmware. Reviewed-by: Arend Van Spriel <arend@broadcom.com> Signed-off-by: Daniel Kim <dekim@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-05-11iwlwifi: mvm: fix setting channel in monitor modeEmmanuel Grumbach
There was a deadlock in monitor mode when we were setting the channel if the channel was not 1. ====================================================== [ INFO: possible circular locking dependency detected ] 3.14.3 #4 Not tainted ------------------------------------------------------- iw/3323 is trying to acquire lock: (&local->chanctx_mtx){+.+.+.}, at: [<ffffffffa062e2f2>] ieee80211_vif_release_channel+0x42/0xb0 [mac80211] but task is already holding lock: (&local->iflist_mtx){+.+...}, at: [<ffffffffa0609e0a>] ieee80211_set_monitor_channel+0x5a/0x1b0 [mac80211] which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #2 (&local->iflist_mtx){+.+...}: [<ffffffff810d95bb>] __lock_acquire+0xb3b/0x13b0 [<ffffffff810d9ee0>] lock_acquire+0xb0/0x1f0 [<ffffffff817eb9c8>] mutex_lock_nested+0x78/0x4f0 [<ffffffffa06225cf>] ieee80211_iterate_active_interfaces+0x2f/0x60 [mac80211] [<ffffffffa0518189>] iwl_mvm_recalc_multicast+0x49/0xa0 [iwlmvm] [<ffffffffa051822e>] iwl_mvm_configure_filter+0x4e/0x70 [iwlmvm] [<ffffffffa05e6d43>] ieee80211_configure_filter+0x153/0x5f0 [mac80211] [<ffffffffa05e71f5>] ieee80211_reconfig_filter+0x15/0x20 [mac80211] [snip] -> #1 (&mvm->mutex){+.+.+.}: [<ffffffff810d95bb>] __lock_acquire+0xb3b/0x13b0 [<ffffffff810d9ee0>] lock_acquire+0xb0/0x1f0 [<ffffffff817eb9c8>] mutex_lock_nested+0x78/0x4f0 [<ffffffffa0517246>] iwl_mvm_add_chanctx+0x56/0xe0 [iwlmvm] [<ffffffffa062ca1e>] ieee80211_new_chanctx+0x13e/0x410 [mac80211] [<ffffffffa062d953>] ieee80211_vif_use_channel+0x1c3/0x5a0 [mac80211] [<ffffffffa06035ab>] ieee80211_add_virtual_monitor+0x1ab/0x6b0 [mac80211] [<ffffffffa06052ea>] ieee80211_do_open+0xe6a/0x15a0 [mac80211] [<ffffffffa0605a79>] ieee80211_open+0x59/0x60 [mac80211] [snip] -> #0 (&local->chanctx_mtx){+.+.+.}: [<ffffffff810d6cb7>] check_prevs_add+0x977/0x980 [<ffffffff810d95bb>] __lock_acquire+0xb3b/0x13b0 [<ffffffff810d9ee0>] lock_acquire+0xb0/0x1f0 [<ffffffff817eb9c8>] mutex_lock_nested+0x78/0x4f0 [<ffffffffa062e2f2>] ieee80211_vif_release_channel+0x42/0xb0 [mac80211] [<ffffffffa0609ec3>] ieee80211_set_monitor_channel+0x113/0x1b0 [mac80211] [<ffffffffa058fb37>] cfg80211_set_monitor_channel+0x77/0x2b0 [cfg80211] [<ffffffffa056e0b2>] __nl80211_set_channel+0x122/0x140 [cfg80211] [<ffffffffa0581374>] nl80211_set_wiphy+0x284/0xaf0 [cfg80211] [snip] other info that might help us debug this: Chain exists of: &local->chanctx_mtx --> &mvm->mutex --> &local->iflist_mtx Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(&local->iflist_mtx); lock(&mvm->mutex); lock(&local->iflist_mtx); lock(&local->chanctx_mtx); *** DEADLOCK *** This deadlock actually occurs: INFO: task iw:3323 blocked for more than 120 seconds. Not tainted 3.14.3 #4 "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. iw D ffff8800c8afcd80 4192 3323 3322 0x00000000 ffff880078fdb7e0 0000000000000046 ffff8800c8afcd80 ffff880078fdbfd8 00000000001d5540 00000000001d5540 ffff8801141b0000 ffff8800c8afcd80 ffff880078ff9e38 ffff880078ff9e38 ffff880078ff9e40 0000000000000246 Call Trace: [<ffffffff817ea841>] schedule_preempt_disabled+0x31/0x80 [<ffffffff817ebaed>] mutex_lock_nested+0x19d/0x4f0 [<ffffffffa06225cf>] ? ieee80211_iterate_active_interfaces+0x2f/0x60 [mac80211] [<ffffffffa06225cf>] ? ieee80211_iterate_active_interfaces+0x2f/0x60 [mac80211] [<ffffffffa052a680>] ? iwl_mvm_power_mac_update_mode+0xc0/0xc0 [iwlmvm] [<ffffffffa06225cf>] ieee80211_iterate_active_interfaces+0x2f/0x60 [mac80211] [<ffffffffa0529357>] _iwl_mvm_power_update_binding+0x27/0x80 [iwlmvm] [<ffffffffa0516eb1>] iwl_mvm_unassign_vif_chanctx+0x81/0xc0 [iwlmvm] [<ffffffffa062d3ff>] __ieee80211_vif_release_channel+0xdf/0x470 [mac80211] [<ffffffffa062e2fa>] ieee80211_vif_release_channel+0x4a/0xb0 [mac80211] [<ffffffffa0609ec3>] ieee80211_set_monitor_channel+0x113/0x1b0 [mac80211] [<ffffffffa058fb37>] cfg80211_set_monitor_channel+0x77/0x2b0 [cfg80211] [<ffffffffa056e0b2>] __nl80211_set_channel+0x122/0x140 [cfg80211] [<ffffffffa0581374>] nl80211_set_wiphy+0x284/0xaf0 [cfg80211] This fixes https://bugzilla.kernel.org/show_bug.cgi?id=75541 Cc: <stable@vger.kernel.org> [3.13+] Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2014-05-09net: cassini: use nested lock annotationEmil Goode
In the cas_lock_tx function we acquire multiple locks in a loop and need to use nested lock annotation to prevent lockdep warnings. Reported-by: Meelis Roos <mroos@linux.ee> Signed-off-by: Emil Goode <emilgoode@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-09bnx2x: Fix UNDI driver unloadYuval Mintz
Commit 91ebb928b "bnx2x: Add support for Multi-Function UNDI" contains a bug which prevent the emptying of the device's Rx buffers before reset. As a result, on new boards it is likely HW will reach some fatal assertion once its interfaces load after UNDI was previously loaded. Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-09net: cpsw: add missing of_node_putJohan Hovold
Add missing of_node_put to avoid kref leak. Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-09net: cpsw: fix null dereference at probeJohan Hovold
Fix null-pointer dereference at probe when the mdio platform device is missing (e.g. when it has been disabled in DT). Cc: stable <stable@vger.kernel.org> # v3.8 Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-09Revert "net: eth: cpsw: Correctly attach to GPIO bitbang MDIO driver"Johan Hovold
This reverts commit f8d56d8f892be43a2404356073e16401eb5a42e6 ("net: eth: cpsw: Correctly attach to GPIO bitbang MDIO driver"). Fix potential null-pointer dereference at probe if the mdio-gpio device has not been successfully probed yet. The offending commit is plain wrong for a number of reasons. First of all it accesses internal driver data of an unrelated device. Neither does it check that the data is non-null (which it is in case the device has not been probed yet). Furthermore, the decision on whether to treat any driver data according to the mdio-gpio driver's internals is made based on the node name. But the name is not compared against "mdio" which is the normal name for the node, but rather against "gpio" which the node does not have to be named (and shouldn't be according to the binding documentation). [ If this hack is to be kept out-of-tree it should at least be matching against the compatible property. ] Cc: Stefan Roese <sr@denx.de> Cc: stable <stable@vger.kernel.org> # v3.14 Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-09net: mdio-gpio: warn about missing bus alias idJohan Hovold
Use a sane default bus id (rather than -ENODEV) and print a warning when the bus alias id is missing. Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-09net: cdc_mbim: handle unaccelerated VLAN tagged framesBjørn Mork
This driver maps 802.1q VLANs to MBIM sessions. The mapping is based on a bogus assumption that all tagged frames will use the acceleration API because we enable NETIF_F_HW_VLAN_CTAG_TX. This fails for e.g. frames tagged in userspace using packet sockets. Such frames will erroneously be considered as untagged and silently dropped based on not being IP. Fix by falling back to looking into the ethernet header for a tag if no accelerated tag was found. Fixes: a82c7ce5bc5b ("net: cdc_ncm: map MBIM IPS SessionID to VLAN ID") Cc: Greg Suarez <gsuarez@smithmicro.com> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-08Driver for Beckhoff CX5020 EtherCAT master module.Darek Marcinkiewicz
This driver adds support for EtherCAT master module located on CCAT FPGA found on Beckhoff CX series industrial PCs. The driver exposes EtherCAT master as an ethernet interface. EtherCAT is a fieldbus protocol defined on top of ethernet and Beckhoff CX5020 PCs come with built-in EtherCAT master module located on a FPGA, which in turn is connected to a PCI bus. Signed-off-by: Dariusz Marcinkiewicz <reksio@newterm.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-08Merge branch 'master' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
2014-05-07qlcnic: Set real_num_{tx|rx}_queues properlyShahed Shaikh
Do not set netdev->real_num_tx_queues directly, let netif_set_real_num_tx_queues() take care of it. Do not overwrite netdev->num_tx_queues everytime when driver changes its Tx ring size through ethtool -L and also notify stack to update number of Rx queues. Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-07qlcnic: Fix panic while dumping TX queues on TX timeoutManish Chopra
o In case of non-multi TX queue mode driver does not initialize "crb_intr_mask" pointer and driver was accessing that un-initialized pointer while dumping TX queue. So dump "crb_intr_mask" only when it is initilaized. Signed-off-by: Manish Chopra <manish.chopra@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-07iwlwifi: pcie: disable interrupts upon PCIe allocEmmanuel Grumbach
In case RFKILL is in KILL position, the NIC will issue an interrupt straight away. This interrupt won't be sent because it is masked in the hardware. But if our interrupt service routine is called for another reason (SHARED_IRQ), then we'll look at the interrupt cause and service it. This can cause bad things if we are not ready yet. Explicitly clean the interrupt cause register to make sure we won't service anything before we are ready to. Cc: <stable@vger.kernel.org> [3.14] Reported-and-tested-by: Alexander Monakov <amonakov@gmail.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2014-05-07jme: Fix DMA unmap warningNeil Horman
The jme driver forgot to check the return status from pci_map_page in its tx path, causing a dma api warning on unmap. Easy fix, just do the check and augment the tx path to tell the stack that the driver is busy so we re-queue the frame. Signed-off-by: Neil Horman <nhorman@tuxdriver.com> CC: Guo-Fu Tseng <cooldavid@cooldavid.org> CC: "David S. Miller" <davem@davemloft.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-07net: cdc_mbim: __vlan_find_dev_deep need rcu_read_lockBjørn Mork
Fixes this warning introduced by commit 5b8f15f78e6f ("net: cdc_mbim: handle IPv6 Neigbor Solicitations"): =============================== [ INFO: suspicious RCU usage. ] 3.15.0-rc3 #213 Tainted: G W O ------------------------------- net/8021q/vlan_core.c:69 suspicious rcu_dereference_check() usage! other info that might help us debug this: rcu_scheduler_active = 1, debug_locks = 1 no locks held by ksoftirqd/0/3. stack backtrace: CPU: 0 PID: 3 Comm: ksoftirqd/0 Tainted: G W O 3.15.0-rc3 #213 Hardware name: LENOVO 2776LEG/2776LEG, BIOS 6EET55WW (3.15 ) 12/19/2011 0000000000000001 ffff880232533bf0 ffffffff813a5ee6 0000000000000006 ffff880232530090 ffff880232533c20 ffffffff81076b94 0000000000000081 0000000000000000 ffff8802085ac000 ffff88007fc8ea00 ffff880232533c50 Call Trace: [<ffffffff813a5ee6>] dump_stack+0x4e/0x68 [<ffffffff81076b94>] lockdep_rcu_suspicious+0xfa/0x103 [<ffffffff813978a6>] __vlan_find_dev_deep+0x54/0x94 [<ffffffffa04a1938>] cdc_mbim_rx_fixup+0x379/0x66a [cdc_mbim] [<ffffffff813ab76f>] ? _raw_spin_unlock_irqrestore+0x3a/0x49 [<ffffffff81079671>] ? trace_hardirqs_on_caller+0x192/0x1a1 [<ffffffffa059bd10>] usbnet_bh+0x59/0x287 [usbnet] [<ffffffff8104067d>] tasklet_action+0xbb/0xcd [<ffffffff81040057>] __do_softirq+0x14c/0x30d [<ffffffff81040237>] run_ksoftirqd+0x1f/0x50 [<ffffffff8105f13e>] smpboot_thread_fn+0x172/0x18e [<ffffffff8105efcc>] ? SyS_setgroups+0xdf/0xdf [<ffffffff810594b0>] kthread+0xb5/0xbd [<ffffffff813a84b1>] ? __wait_for_common+0x13b/0x170 [<ffffffff810593fb>] ? __kthread_parkme+0x5c/0x5c [<ffffffff813b147c>] ret_from_fork+0x7c/0xb0 [<ffffffff810593fb>] ? __kthread_parkme+0x5c/0x5c Fixes: 5b8f15f78e6f ("net: cdc_mbim: handle IPv6 Neigbor Solicitations") Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-06iwlwifi: mvm: do no sched scan while associatedDavid Spinadel
Currently the FW doesn't support sched scan while associated, Prevent it. Signed-off-by: David Spinadel <david.spinadel@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Reviewed-by: Luciano Coelho <luciano.coelho@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2014-05-06iwlwifi: mvm: rs - s/CPTCFG/CONFIGEmmanuel Grumbach
My bad - I forgot to update this when sending the patch upstream. Fixes: 87d5e4155c00 ("iwlwifi: mvm: rs: reinit rs if no tx for a long time") Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2014-05-06iwlwifi: mvm: BT Coex - fix validity flags during initEmmanuel Grumbach
The commit below introduced a bug in the validity bits in init. Due to that, all the Coex mechanism stopped sending kills to the BT side. Fix that. Fixes: b9fae2d54c9f ("iwlwifi: mvm: BT Coex add support for Co-running block") Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2014-05-05net: macb: Fix race between HW and driverSoren Brinkmann
Under "heavy" RX load, the driver cannot handle the descriptors fast enough. In detail, when a descriptor is consumed, its used flag is cleared and once the RX budget is consumed all descriptors with a cleared used flag are prepared to receive more data. Under load though, the HW may constantly receive more data and use those descriptors with a cleared used flag before they are actually prepared for next usage. The head and tail pointers into the RX-ring should always be valid and we can omit clearing and checking of the used flag. Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-05net: macb: Remove 'unlikely' optimizationSoren Brinkmann
Coverage data suggests that the unlikely case of receiving data while the receive handler is running may not be that unlikely. Coverage data after running iperf for a while: 91320: 891: work_done = bp->macbgem_ops.mog_rx(bp, budget); 91320: 892: if (work_done < budget) { 2362: 893: napi_complete(napi); -: 894: -: 895: /* Packets received while interrupts were disabled */ 4724: 896: status = macb_readl(bp, RSR); 2362: 897: if (unlikely(status)) { 762: 898: if (bp->caps & MACB_CAPS_ISR_CLEAR_ON_WRITE) 762: 899: macb_writel(bp, ISR, MACB_BIT(RCOMP)); -: 900: napi_reschedule(napi); -: 901: } else { 1600: 902: macb_writel(bp, IER, MACB_RX_INT_FLAGS); -: 903: } -: 904: } Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-05net: macb: Re-enable RX interrupt only when RX is doneSoren Brinkmann
When data is received during the driver processing received data the NAPI is re-scheduled. In that case the RX interrupt should not be re-enabled. Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3-18-g5258 (git 2.32.0) at 2024-12-02 02:16:33 +0000