| Age | Commit message (Collapse) | Author |
|---|
|
This converts pretty much everything to print_mac. There were
a few things that had conflicts which I have just dropped for
now, no harm done.
I've built an allyesconfig with this and looked at the files
that weren't built very carefully, but it's a huge patch.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
free sk_buff with kfree_skb, instead of kree
Signed-off-by: Sergio Luis <sergio@larces.uece.br>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 7bf6bf4803df1adc927f585168d2135fb019c698.
The code has both a short existence and an increasing track of failures
despite some work to amend it for -rc1. It is not just a matter of
reading the eeprom: sometimes the eeprom is read correctly, then the mac
address is not written correctly back into the mac registers.
Some chipsets seem to work reliably but it is not clear at this point if
the code can simply be made to work on a per-chipset basis and post -rc1
is not the place where I want to experiment these things.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (29 commits)
tcp: Restore ordering of TCP options for the sake of inter-operability
net: Fix disjunct computation of netdev features
sctp: Fix to handle SHUTDOWN in SHUTDOWN_RECEIVED state
sctp: Fix to handle SHUTDOWN in SHUTDOWN-PENDING state
sctp: Add check for the TSN field of the SHUTDOWN chunk
sctp: Drop ICMP packet too big message with MTU larger than current PMTU
p54: enable 2.4/5GHz spectrum by eeprom bits.
orinoco: reduce stack usage in firmware download path
ath5k: fix suspend-related oops on rmmod
[netdrvr] fec_mpc52xx: Implement polling, to make netconsole work.
qlge: Fix MSI/legacy single interrupt bug.
smc911x: Make the driver safer on SMP
smc911x: Add IRQ polarity configuration
smc911x: Allow Kconfig dependency on ARM
sis190: add identifier for Atheros AR8021 PHY
8139x: reduce message severity on driver overlap
igb: add IGB_DCA instead of selecting INTEL_IOATDMA
igb: fix tx data corruption with transition to L0s on 82575
ehea: Fix memory hotplug support
netdev: DM9000: remove BLACKFIN hacking in DM9000 netdev driver
...
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/czankel/xtensa-2.6:
xtensa: Add config files for Diamond 232L - Rev B processor variant
xtensa: Fix io regions
xtensa: Add support for the Sonic Ethernet device for the XT2000 board.
xtensa: replace remaining __FUNCTION__ occurrences
xtensa: use newer __SPIN_LOCK_UNLOCKED macro
XTENSA: warn about including <asm/rwsem.h> directly.
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (53 commits)
powerpc: Support for relocatable kdump kernel
powerpc: Don't use a 16G page if beyond mem= limits
powerpc: Add del_node() for early boot code to prune inapplicable devices.
powerpc: Further compile fixup for STRICT_MM_TYPECHECKS
powerpc: Remove empty #else from signal_64.c
powerpc: Move memory size print into common show_cpuinfo for 32-bit
hvc_console: Remove __devexit annotation of hvc_remove()
hvc_console: Add support for tty window resizing
hvc_console: Fix loop if put_char() returns 0
hvc_console: Add tty driver flag TTY_DRIVER_RESET_TERMIOS
hvc_console: Add a hangup notifier for backends
powerpc/83xx: Add DS1339 RTC support for MPC8349E-mITX boards .dts
powerpc/83xx: Add support for MCU microcontroller in .dts files
powerpc/85xx: Move mpc8572ds.dts to address-cells/size-cells = <2>
of/spi: Support specifying chip select as active high via device tree
powerpc: Remove device_type = "board_control" properties in .dts files
i2c-cpm: Suppress autoprobing for devices
powerpc/85xx: Fix mpc8536ds dma interrupt numbers
powerpc/85xx: Enable enhanced functions for 8536 TSEC
powerpc: Delete unused prom_strtoul and prom_memparse
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/ehca: Reject dynamic memory add/remove when ehca adapter is present
IB/ehca: Fix reported max number of QPs and CQs in systems with >1 adapter
IPoIB: Set netdev offload features properly for child (VLAN) interfaces
IPoIB: Clean up ethtool support
mlx4_core: Add Ethernet PCI device IDs
mlx4_en: Add driver for Mellanox ConnectX 10GbE NIC
mlx4_core: Multiple port type support
mlx4_core: Ethernet MAC/VLAN management
mlx4_core: Get ethernet MTU and default address from firmware
mlx4_core: Support multiple pre-reserved QP regions
Update NetEffect maintainer emails to Intel emails
RDMA/cxgb3: Remove cmid reference on tid allocation failures
IB/mad: Use krealloc() to resize snoop table
IPoIB: Always initialize poll_timer to avoid crash on unload
IB/ehca: Don't allow creating UC QP with SRQ
mlx4_core: Add QP range reservation support
RDMA/ucma: Test ucma_alloc_multicast() return against NULL, not with IS_ERR()
|
|
My change
commit e2a6b85247aacc52d6ba0d9b37a99b8d1a3e0d83
net: Enable TSO if supported by at least one device
didn't do what was intended because the netdev_compute_features
function was designed for conjunctions. So what happened was that
it would simply take the TSO status of the last constituent device.
This patch extends it to support both conjunctions and disjunctions
under the new name of netdev_increment_features.
It also adds a new function netdev_fix_features which does the
sanity checking that usually occurs upon registration. This ensures
that the computation doesn't result in an illegal combination
since this checking is absent when the change is initiated via
ethtool.
The two users of netdev_compute_features have been converted.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
The Mellanox ConnectX can operate as an InfiniBand adapter, as an
Ethernet NIC, or as a Fibre Channel (FC) HBA. The kernel has a
low-level driver, mlx4_core, which handles multiplexing access to the
device, and there is also already an InfiniBad driver, mlx4_ib.
This patch adds a new driver, mlx4_en, which implements a standard
Ethernet NIC driver.
Signed-off-by: Liran Liss <liranl@mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Multi-protocol adapters support different port types. Each consumer
of mlx4_core queries for supported port types; in particular mlx4_ib
can no longer assume that all physical ports belong to it. Port type
is configured through a sysfs interface. When the type of a port is
changed, all mlx4 interfaces are unregistered, and then registered
again with the new port types.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Badness at /home/proski/src/linux-2.6/net/mac80211/rx.c:2200
NIP: c02bc850 LR: c02ab268 CTR: 00000000
REGS: ef01fcc0 TRAP: 0700 Tainted: G W (2.6.27-wl)
MSR: 00029032 <EE,ME,IR,DR> CR: 22004084 XER: 20000000
TASK = c1a58800[1778] 'p54pci' THREAD: ef01e000
[...]
NIP [c02bc850] __ieee80211_rx+0x17c/0x638
LR [c02ab268] ieee80211_tasklet_handler+0x104/0x120
Call Trace:
[ef01fd70] [c1a0c020] 0xc1a0c020 (unreliable)
[ef01fdb0] [c02ab268] ieee80211_tasklet_handler+0x104/0x120
[...]
the problem was that some older cards are mis-identified and didn't support
5GHz rates, while they have the right MAC & Synth chip.
This patch changes the way how p54 decides if it should enable 11a channels
or not.
Reported-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
orinoco_dl_firmware and symbol_dl_mage allocate large local
variables (1K); at least orinoco fails with panic or hung
kernel if 4K stacks is enabled.
Allocate large buffers dynamically at run time.
Tested-By: Andrey Borzenkov <arvidjaar@mail.ru> for Agere case
Signed-off-by: Andrey Borzenkov < arvidjaar@mail.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Based on a patch by Elias Oltmanns, we call ath5k_init in resume even
if we didn't previously open the device. Besides starting up the
device unnecessarily, this also causes an oops on rmmod because
mac80211 will not invoke ath5k_stop and softirqs are left running after
the module has been unloaded. Add a new state bit, ATH_STAT_STARTED,
to indicate that we have been started up.
Reported-by: Toralf Förster <toralf.foerster@gmx.de>
Signed-off-by: Elias Oltmanns <eo@nebensachen.de>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Add support for managing MAC and VLAN filters for each port.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Oren Duer <oren@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Get maximum ethernet MTU and default MAC address from the firmware
QUERY_DEV_CAP command.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
For ethernet support, we need to reserve QPs for the ethernet and
fibre channel driver. The QPs are reserved at the end of the QP
table. (This way we assure that they are aligned to their size)
We need to consider these reserved ranges in bitmap creation, so we
extend the mlx4 bitmap utility functions to allow reserved ranges at
both the bottom and the top of the range.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Implement polling for 5200FEC to make netconsole work. Tested on
Phytec pcm030 and Efika.
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
The chip can issue spurious interrupts for single interrupt
modes. We use disable to clear the condition and allow processing to
continue. Also got rid of legacy specific code since it now needs to
be done on MSI single irq also.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
This patch extends the critical regions covered by lp->lock to make it
safer on SMP. The main failure point was the smc911x_hard_start_xmit
function being called from different CPUs. It was tested on the ARM SMP
platforms.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Platforms like ARM Ltd's RealView require the IRQ polarity bit to be set
for the SMC9118 chip. This patch allows the dynamic configuration via
the smc911x_platdata structure.
This patch also changes the smc91x_platdata structure name to the
correct smc911x_platdata in the smc911x_drv_probe() function.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Since more ARM platforms use this device, it is easier to add a
dependency on ARM rather than individual platforms.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Fixes http://bugzilla.kernel.org/show_bug.cgi?id=10994
Contributed by pablomme@googlemail.com, coenraad@wish.org.za
and a few others.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
The 8139 drivers are a source of error messages that confuse users.
Since this device can not be disambiguated by normal PCI device
id's two drivers match the same info. But the module utilities
seem to correctly handle this overlap, they try one driver, then
if that doesn't load try the other. Therefore there is no need for
a message to be logged with error level severity, just using info
level instead. Can't be completely silent because user might have
configure one driver and forgot the other one.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Add a bool IGB_DCA defined to y if IGB and DCA are enabled, but IGB isn't y while DCA=m. And thus remove the need to select INTEL_IOATDMA when IGB is enabled, so that non-x86 architectures can build the igb driver.
Based on work/patch from Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
The 82575 has an issue in which the DMA will go out of sync if the link
partner goes into an L0s state. To prevent this we set the pci-e link
partner capability bits to disable the L0s transition on the hw.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
This patch implements the memory notifier to update the busmap
instantly instead of rebuilding the whole map. This is necessary
because walk_memory_resource provides different information than
required during memory hotplug.
Signed-off-by: Hannes Hering <hering2@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
remove integer casting in the read/write IO accessors,
because Blackfin now provides those functions
Tested-by: Javier Herrero <jherrero@hvsistemas.es>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Commit 147e70e6 ("cxgb3: Use SKB list interfaces instead of home-grown
implementation.") causes a crash in t3_l2t_send_slow() when an iWARP
connection request is received. This is because the new l2t_entry.arpq
skb queue is never initialized, and therefore trying to add an skb to
it causes a NULL dereference. With the old code there was no need to
initialize the queues because the l2t_entry structures were zeroed,
and the code used NULL to mean empty.
Fix this by adding __skb_queue_head_init() when all the l2t_entry
structures get allocated.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Currently SMC911x driver is broken on ARM/PXA builds.
Unbreak such configurations.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Disable NAPI if a failure occurs when setting up the interface. Leaving
it enabled could cause a BUG the next time an ifconfig up is issued.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
RBTX4939 board has SMC91X chip and there can be other MIPS boards with
that chip. Make SMC91X selectable on all MIPS board would be better than
enumerating each boards in Kconfig.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: jeff@garzik.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
dev->irq is unsigned
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
platform_get_irq*() returns on -ENXIO when the resource cannot be
found, but this remains unnoticed if stored in an unsigned.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Checking the signature of the eeprom and the validity of the
MAC address should be enough to filter out the bad addresses
observed so far.
Contributed by Ivan Vecera and Martin Capitanio.
Tested on 8102el, 8168b and 8169 for a start.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
|
|
I prefer the debug information to be displayed until
the issue is properly handled.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
|
|
Add support for the on-board Sonic Ethernet device for the XT2000
evaluation board.
Signed-off-by: Chris Zankel <chris@zankel.net>
|
|
Manual merge of:
arch/powerpc/Kconfig
arch/powerpc/include/asm/page.h
|
|
|
|
Support for new features needed by the PPC 405EZ boards
introduced some errors in the MAL and EMAC feature handling.
This broke 'allmodconfig' builds as CONFIG_PPC_DCR_NATIVE is
not set for those.
This patch fixes these errors by wrapping the code in the
appropriate #ifdefs.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
|
|
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
This merges branches irq/genirq, irq/sparseirq-v4, timers/hpet-percpu
and x86/uv.
The sparseirq branch is just preliminary groundwork: no sparse IRQs are
actually implemented by this tree anymore - just the new APIs are added
while keeping the old way intact as well (the new APIs map 1:1 to
irq_desc[]). The 'real' sparse IRQ support will then be a relatively
small patch ontop of this - with a v2.6.29 merge target.
* 'genirq-v28-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (178 commits)
genirq: improve include files
intr_remapping: fix typo
io_apic: make irq_mis_count available on 64-bit too
genirq: fix name space collisions of nr_irqs in arch/*
genirq: fix name space collision of nr_irqs in autoprobe.c
genirq: use iterators for irq_desc loops
proc: fixup irq iterator
genirq: add reverse iterator for irq_desc
x86: move ack_bad_irq() to irq.c
x86: unify show_interrupts() and proc helpers
x86: cleanup show_interrupts
genirq: cleanup the sparseirq modifications
genirq: remove artifacts from sparseirq removal
genirq: revert dynarray
genirq: remove irq_to_desc_alloc
genirq: remove sparse irq code
genirq: use inline function for irq_to_desc
genirq: consolidate nr_irqs and for_each_irq_desc()
x86: remove sparse irq from Kconfig
genirq: define nr_irqs for architectures with GENERIC_HARDIRQS=n
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6
Conflicts:
Documentation/kernel-parameters.txt
arch/sh/include/asm/elf.h
|
|
USB should not be having it's own printk macros, so remove info() and
use the system-wide standard of dev_info() wherever possible.
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
USB should not be having it's own printk macros, so remove warn() and
use the system-wide standard of dev_warn() wherever possible. In the
few places that will not work out, use a basic printk().
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
net: Remove CONFIG_KMOD from net/ (towards removing CONFIG_KMOD entirely)
ipv4: Add a missing rcu_assign_pointer() in routing cache.
[netdrvr] ibmtr: PCMCIA IBMTR is ok on 64bit
xen-netfront: Avoid unaligned accesses to IP header
lmc: copy_*_user under spinlock
[netdrvr] myri10ge, ixgbe: remove broken select INTEL_IOATDMA
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6: (46 commits)
UIO: Fix mapping of logical and virtual memory
UIO: add automata sercos3 pci card support
UIO: Change driver name of uio_pdrv
UIO: Add alignment warnings for uio-mem
Driver core: add bus_sort_breadthfirst() function
NET: convert the phy_device file to use bus_find_device_by_name
kobject: Cleanup kobject_rename and !CONFIG_SYSFS
kobject: Fix kobject_rename and !CONFIG_SYSFS
sysfs: Make dir and name args to sysfs_notify() const
platform: add new device registration helper
sysfs: use ilookup5() instead of ilookup5_nowait()
PNP: create device attributes via default device attributes
Driver core: make bus_find_device_by_name() more robust
usb: turn dev_warn+WARN_ON combos into dev_WARN
debug: use dev_WARN() rather than WARN_ON() in device_pm_add()
debug: Introduce a dev_WARN() function
sysfs: fix deadlock
device model: Do a quickcheck for driver binding before doing an expensive check
Driver core: Fix cleanup in device_create_vargs().
Driver core: Clarify device cleanup.
...
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
module: remove CONFIG_KMOD in comment after #endif
remove CONFIG_KMOD from fs
remove CONFIG_KMOD from drivers
Manually fix conflict due to include cleanups in drivers/md/md.c
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (26 commits)
decnet: Fix compiler warning in dn_dev.c
IPV6: Fix default gateway criteria wrt. HIGH/LOW preference radv option
net/802/fc.c: Fix compilation warnings
netns: correct mib stats in ip6_route_me_harder()
netns: fix net_generic array leak
rt2x00: fix regression introduced by "mac80211: free up 2 bytes in skb->cb"
rtl8187: Add USB ID for Belkin F5D7050 with RTL8187B chip
p54usb: Device ID updates
mac80211: fixme for kernel-doc
ath9k/mac80211: disallow fragmentation in ath9k, report to userspace
libertas : Remove unused variable warning for "old_channel" from cmd.c
mac80211: Fix scan RX processing oops
orinoco: fix unsafe locking in spectrum_cs_suspend
orinoco: fix unsafe locking in orinoco_cs_resume
cfg80211: fix debugfs error handling
mac80211: fix debugfs netdev rename
iwlwifi: fix ct kill configuration for 5350
mac80211: fix HT information element parsing
p54: Fix compilation problem on PPC
mac80211: fix debugfs lockup
...
|
