| Age | Commit message (Collapse) | Author |
|---|
|
changes
commit 07d69d4238418746a7b85c5d05ec17c658a2a390 upstream.
Without this patch sysfs reports the cable as present
flag@flag-desktop:~$ cat /sys/class/net/eth0/carrier
1
while it's not:
flag@flag-desktop:~$ sudo mii-tool eth0
eth0: no link
Tested on my Beagle XM.
v2: added mantainer to the list of recipient
Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Acked-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 1ed2ec37b44e86eaa8e0a03b908a39c80f65ee45 upstream.
"iwlwifi: use correct released ucode version" change
the ucode api ok from 6000G2 to 6000G2B, but it shall belong
to 6030 device series, not the 6005 device series. Fix it
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 78cbcf2b9dbe0565820dc7721316f9c401000a68 upstream.
Report correctly the latest released version
of the iwlwifi firmware for all
iwlwifi-supported devices.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit b914811524fbe9e91fe50845f5d7bd4316b8a6ee upstream.
Since the uCode hasn't been released (yet?),
warn only if using older than API 4, but load
anything up to API 6.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 5ef4acd58ab2abd0dd0c8e3cacd61a0dc5d73646 upstream.
Newer devices have 20 (5000 series) or 30 (6000 series)
hardware queues, rather than the 16 that 4965 had. This
was added to the driver a long time ago, but improperly:
the queue registers for the higher queues aren't just
continuations of the registers for the first 16 queues,
they are in other places. Therefore, the hardware would
lock up when trying to activate queue 16 or above and
the device would have to be restarted.
Thanks goes to Emmanuel who identified this and told me
how the queue programming should be done.
Note that we don't use queues 20 and higher today and
doing so needs more work than this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 8db4c7e25d153fb049e81715d72fa3be3a0c3b69 upstream.
ctx->vif is dereferenced in different part of iwlwifi code, so do not
nullify it.
This should address at least one of the possible reasons of WARNING at
iwlagn_mac_remove_interface, and perhaps some random crashes when
firmware reset is performed.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
[bwh: Backported to 3.2:
- Change filename iwl-mac80211.c to iwl-core.c
- Change context in iwlagn_prepare_restart()]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 4c1bcdb5a3354b250b82a67549f57ac27a3bb85f upstream.
This driver currently leaves elp_work behind when stopping, which
occasionally results in data corruption because work function ends
up accessing freed memory, typical symptoms of this are various
worker_thread crashes. Fix it by cancelling elp_work.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 328c32f0f85467af5a6c4c3289e168d9ad2555af upstream.
Currently SDIO glue frees it's own structure before calling
wl1251_free_hw(), which in turn calls ieee80211_unregister_hw().
The later call may result in a need to communicate with the chip
to stop it (as it happens now if the interface is still up before
rmmod), which means calls are made back to the glue, resulting in
freed memory access.
Fix this by freeing glue data last.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 44eb65cfd8da4b9c231238998729e858e963a980 upstream.
Under some circumstances, a PCI-based driver reports the following OOPs:
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] Oops: 0000 [#1] SMP
--snip--
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] Pid: 19627, comm: rmmod
Not tainted 3.2.9-2.fc16.x86_64 #1 LENOVO 05962RU/05962RU
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] RIP:
0010:[<ffffffffa0418d39>] [<ffffffffa0418d39>]
rtl92ce_get_desc+0x19/0xd0 [rtl8192ce]
--snip--
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] Process rmmod (pid:
19627, threadinfo ffff880050262000, task ffff8801156d5cc0)
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] Stack:
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] 0000000000000002
ffff8801176c2540 ffff880050263ca8 ffffffffa03348e7
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] 0000000000000282
0000000180150014 ffff880050263fd8 ffff8801176c2810
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] ffff880050263bc8
ffffffff810550e2 00000000000002c0 ffff8801176c0d40
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] Call Trace:
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] [<ffffffffa03348e7>]
_rtl_pci_rx_interrupt+0x187/0x650 [rtlwifi]
--snip--
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] Code: ff 09 d0 89 07 48
83 c4 08 5b 5d c3 66 0f 1f 44 00 00 55 48 89 e5 53 48 83 ec 08 66 66
66 66 90 40 84 f6 89 d3 74 13 84 d2 75 57 <8b> 07 48 83 c4 08 5b 5d c1
e8 1f c3 0f 1f 00 84 d2 74 ed 80 fa
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] RIP
[<ffffffffa0418d39>] rtl92ce_get_desc+0x19/0xd0 [rtl8192ce]
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] RSP <ffff880050263b58>
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] CR2: 00000000000006e0
Mar 19 08:14:35 kvothe kernel: [ 6584.646491] ---[ end trace
8636c766dcfbe0e6 ]---
This oops is due to interrupts not being disabled in this particular path.
Reported-by: Dave Airlie <airlied@gmail.com>
Tested-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit dd447319895d0c0af423e483d9b63f84f3f8869a upstream.
Driver incorrectly validates command completion: instead of waiting
for a command to be acknowledged it continues execution. Most of the
time driver gets acknowledge of the command completion in a tasklet
before it executes the next one. But sometimes it sends the next
command before it gets acknowledge for the previous one. In such a
case one of the following error messages appear in the log:
Failed to send SYSTEM_CONFIG: Already sending a command.
Failed to send ASSOCIATE: Already sending a command.
Failed to send TX_POWER: Already sending a command.
After that you need to reload the driver to get it working again.
This bug occurs during roaming (reported by Sam Varshavchik)
https://bugzilla.redhat.com/show_bug.cgi?id=738508
and machine booting (reported by Tom Gundersen and Mads Kiilerich)
https://bugs.archlinux.org/task/28097
https://bugzilla.redhat.com/show_bug.cgi?id=802106
This patch doesn't fix the delay issue during firmware load.
But at least device now works as usual after boot.
Signed-off-by: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit dbdedbdf4fbff3d4962a0786f37aa86dfdc48a7e upstream.
Commit 2a19032 (b43: reload phy and bss settings after core restarts)
introduced an unconditional call to b43_op_config() at the end of
b43_op_start(). When firmware fails to load this can wedge the system.
There's no need to reload the configuration after a failed
initialization anyway, so only make the call if initialization was
successful.
BugLink: http://bugs.launchpad.net/bugs/950295
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
[ Upstream commit 716af4abd6e6370226f567af50bfaca274515980 ]
MAX_ADDR_LEN is 32. ETH_ALEN is 6. mac->sa_data is a 14 byte array, so
the memcpy() is doing a read past the end of the array. I asked about
this on netdev and Ben Hutchings told me it's supposed to be copying
ETH_ALEN bytes (thanks Ben).
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 890fdf2a0cb88202d1427589db2cf29c1bdd3c1d upstream.
In register_netdevice(), when ndo_init() is successful and later
some error occurred, ndo_uninit() will be called.
So dummy deivce is desirable to implement ndo_uninit() method
to free percpu stats for this case.
And, ndo_uninit() is also called along with dev->destructor() when
device is unregistered, so in order to prevent dev->dstats from
being freed twice, dev->destructor is modified to free_netdev().
Signed-off-by: Hiroaki SHIMODA <shimoda.hiroaki@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
[ Upstream commit a99ff7d0123b19ecad3b589480b6542716ab6b52 ]
Make smsc75xx recalculate the hard_mtu after adjusting the
hard_header_len.
Without this, usbnet adjusts the MTU down to 1492 bytes, and the host is
unable to receive standard 1500-byte frames from the device.
Inspired by same fix on cdc_eem 78fb72f7936c01d5b426c03a691eca082b03f2b9.
Tested on ARM/Omap3 with EVB-LAN7500-LC.
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
[ Upstream commit 8a9a0ea6032186e3030419262678d652b88bf6a8 ]
At the beginning of ks_rcv(), a for loop retrieves the
header information relevant to all the frames stored
in the mac's internal buffers. The number of pending
frames is stored as an 8 bits field in KS_RXFCTR.
If interrupts are disabled long enough to allow for more than
32 frames to accumulate in the MAC's internal buffers, a buffer
overflow occurs.
This patch fixes the problem by making the
driver's frame_head_info buffer big enough.
Well actually, since the chip appears to have 12K of
internal rx buffers and the shortest ethernet frame should
be 64 bytes long, maybe the limit could be set to
12*1024/64 = 192 frames, but 255 should be safer.
Signed-off-by: Davide Ciminaghi <ciminaghi@gnudd.com>
Signed-off-by: Raffaele Recalcati <raffaele.recalcati@bticino.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
[ Upstream commit 3c5e979bd037888dd7d722da22da4b43659af485 ]
The SMSC911x driver resets the ->head, ->data and ->tail pointers in the
skb on the reset path in order to avoid buffer overflow due to packet
padding performed by the hardware.
This patch fixes the receive path so that the skb pointers are fixed up
after the data has been read from the device, The error path is also
fixed to use number of words consistently and prevent erroneous FIFO
fastforwarding when skipping over bad data.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
[ Upstream commit a8c9cb106fe79c28d6b7f1397652cadd228715ff ]
We set intr mask before its handler is registered, this does not work well when
8139cp is sharing irq line with other devices. As the irq could be enabled by
the device before 8139cp's hander is registered which may lead unhandled
irq. Fix this by introducing an helper cp_irq_enable() and call it after
request_irq().
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
[ Upstream commit 03662e41c7cff64a776bfb1b3816de4be43de881 ]
Problem:
There was two separate work_struct structures which share one
handler. Unfortunately getting atl1_adapter structure from
work_struct in case of DMA error was done from incorrect
offset which cause kernel panics.
Solution:
The useless work_struct for DMA error removed and
handler name changed to more generic one.
Signed-off-by: Tony Zelenoff <antonz@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
[ Upstream commit 4eee6a3a04e8bb53fbe7de0f64d0524d3fbe3f80 ]
This happened on a machine with a custom hotplug script calling nameif,
probably due to slow firmware loading. At the time nameif uses ethtool
to gather interface information, i2400m->fw_name is zero and so a null
pointer dereference occurs from within i2400m_get_drvinfo().
Signed-off-by: Phil Sutter <phil.sutter@viprinet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
[ Upstream commit 5a4309746cd74734daa964acb02690c22b3c8911 ]
When a slave comes up, we're unsetting the current_arp_slave without
removing active flags from it, which can lead to situations where we have
more than one slave with active flags in active-backup mode.
To avoid this situation we must remove the active flags from a slave before
removing it as a current_arp_slave.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
[ This combines upstream commit
e675f0cc9a872fd152edc0c77acfed19bf28b81e and follow-on bug fix
commit 9a5d2bd99e0dfe9a31b3c160073ac445ba3d773f ]
For every transmitted packet, ppp_start_xmit() will stop the netdev
queue and then, if appropriate, restart it. This causes the TX softirq
to run, entirely gratuitously.
This is "only" a waste of CPU time in the normal case, but it's actively
harmful when the PPP device is a TEQL slave — the wakeup will cause the
offending device to receive the next TX packet from the TEQL queue, when
it *should* have gone to the next slave in the list. We end up seeing
large bursts of packets on just *one* slave device, rather than using
the full available bandwidth over all slaves.
This patch fixes the problem by *not* unconditionally stopping the queue
in ppp_start_xmit(). It adds a return value from ppp_xmit_process()
which indicates whether the queue should be stopped or not.
It *doesn't* remove the call to netif_wake_queue() from
ppp_xmit_process(), because other code paths (especially from
ppp_output_wakeup()) need it there and it's messy to push it out to the
other callers to do it based on the return value. So we leave it in
place — it's a no-op in the case where the queue wasn't stopped, so it's
harmless in the TX path.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit bc93eda7e903ff75cefcb6e247ed9b8e9f8e9783 upstream.
According to the latest USB ID database these are all RT2770 / RT2870 / RT307x
devices.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
[bwh: Backported to 3.2: adjust context for previously cherry-picked
commit d42a179b941a9e4cc6cf41d0f3cbadd75fc48a89 'rt2x00: Add support
for D-Link DWA-127 to rt2800usb']
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 3ac44670ad0fca8b6c43b3e4d8494c67c419f494 upstream.
Just another USB identifier.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit badc4f07622f0f7093a201638f45e85765f1b5e4 upstream.
There have been reports about not being able to use access-points
on channel 12 and 13 or having connectivity issues when these channels
were part of the selected regulatory domain. Upon switching to these
channels the brcmsmac driver suspends the transmit dma fifos. This
patch resumes them upon handing over the first received beacon to
mac80211.
This patch is to be applied to the stable tree for kernel versions
3.2 and 3.3.
Tested-by: Francesco Saverio Schiavarelli <fschiava@libero.it>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Brett Rudley <brudley@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 428ca8a7065354877db63ceabfc493107686eebe upstream.
The scratch register addresses have been changed for newer chips.
Since the old chip was never shipped and it will not be supported
any more, just update register addresses to support the new chips.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 5b76d0600b2b08eef77f8e9226938b7b6bde3099 upstream.
Under heavy load (flood ping) it is possible for the MDIO timeout to
expire before the loop checks the GO bit again. This patch adds an
additional check whether the operation was done before actually
returning -ETIMEDOUT.
To reproduce this bug, flood ping the device, e.g., ping -f -l 1000
After some time, a "timed out waiting for user access" warning
may appear. And even worse, link may go down since the PHY reported a
timeout.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 73f98eab9b9e0bab492ca06add5657d9e702ddb1 upstream.
pch_gbe_validate_option() modifies 32 bits of memory but we pass
&hw->phy.autoneg_advertised which only has 16 bits and &hw->mac.fc
which only has 8 bits.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2b53d07891630dead46d65c8f896955fd3ae0302 upstream.
If the MAC is invalid or not implemented, do not abort the probe. Issue
a warning and prevent bringing the interface up until a MAC is set manually
(via ifconfig $IFACE hw ether $MAC).
Tested on two platforms, one with a valid MAC, the other without a MAC. The real
MAC is used if present, the interface fails to come up until the MAC is set on
the other. They successfully get an IP over DHCP and pass a simple ping and
login over ssh test.
This is meant to allow the Inforce SYS940X development board:
http://www.inforcecomputing.com/SYS940X_ECX.html
(and others suffering from a missing MAC) to work with the mainline kernel.
Without this patch, the probe will fail and the interface will not be created,
preventing the user from configuring the MAC manually.
This does not make any attempt to address a missing or invalid MAC for the
pch_phub driver.
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
CC: Arjan van de Ven <arjan@linux.intel.com>
CC: Alan Cox <alan@linux.intel.com>
CC: Tomoya MORINAGA <tomoya.rohm@gmail.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: Jon Mason <jdmason@kudzu.us>
CC: Mark Brown <broonie@opensource.wolfsonmicro.com>
CC: David Laight <David.Laight@ACULAB.COM>
CC: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2ee0a07028d2cde6e131b73f029dae2b93c50f3a upstream.
Currently the maximum noise floor limit is set as too high (-60dB). The
assumption of having a higher threshold limit is that it would help
de-sensitize the receiver (reduce phy errors) from continuous
interference. But when we have a bursty interference where there are
collisions and then free air time and if the receiver is desensitized too
much, it will miss the normal packets too. Lets make use of chips
specific min, nom and max limits always. This patch helps to improve the
connection stability in congested networks.
Cc: Paul Stewart <pstew@google.com>
Tested-by: Gary Morain <gmorain@google.com>
Signed-off-by: Madhan Jaganathan <madhanj@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
[bwh: Backported to 3.0/3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 673f7786e205c87b5d978c62827b9a66d097bebb upstream.
In https://bugzilla.kernel.org/show_bug.cgi?id=42976, a system with driver
rtl8192se used as an AP suffers from "Out of SW-IOMMU space" errors. These
are caused by the DMA buffers used for beacons never being unmapped.
This bug was also reported at
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/961618
Reported-and-Tested-by: Da Xue <da@lessconfused.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a2daf263107ba3eb6db33931881731fa51c95045 upstream.
Added Vendor/Device Id of Motorola Rokr E6 (22b8:6027) so it can be
recognized by the "zaurus" USBNet driver.
Applies to Linux 3.2.13 and 2.6.39.4.
Signed-off-by: Guan Xin <guanx.bac@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2a15cd2ff488a9fdb55e5e34060f499853b27c77 upstream.
With runtime PM, if the ethernet cable is disconnected, the device is
transitioned to D3 state to conserve energy. If the system is shutdown
in this state, any register accesses in rtl_shutdown are dropped on
the floor. As the device was programmed by .runtime_suspend() to wake
on link changes, it is thus brought back up as soon as the link recovers.
Resuming every suspended device through the driver core would slow things
down and it is not clear how many devices really need it now.
Original report and D0 transition patch by Sameer Nanda. Patch has been
changed to comply with advices by Rafael J. Wysocki and the PM folks.
Reported-by: Sameer Nanda <snanda@chromium.org>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Hayes Wang <hayeswang@realtek.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 643c61e119459e9d750087b7b34be94491efebf9 upstream.
In https://bugzilla.redhat.com/show_bug.cgi?id=770207, slowdowns of driver
rtl8192ce are reported. One fix (commit a9b89e2) has already been applied,
and it helped, but the maximum RX speed would still drop to 1 Mbps. As in
the previous fix, the initial gain was determined to be the problem; however,
the problem arises from a setting of the gain when scans are started.
Driver rtl8192de also has the same code structure - this one is fixed as well.
Reported-and-Tested-by: Ivan Pesin <ivan.pesin@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 464b57da56910c8737ede75ad820b9a7afc46b3e ]
The merge done in commit b26e478f undid bug fix in commit c3e072f8
("net: fsl_pq_mdio: fix non tbi phy access"), with the result that non
TBI (e.g. MDIO) PHYs cannot be accessed.
Signed-off-by: Kenth Eriksson <kenth.eriksson@transmode.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 78fb72f7936c01d5b426c03a691eca082b03f2b9 ]
Make CDC EEM recalculate the hard_mtu after adjusting the
hard_header_len.
Without this, usbnet adjusts the MTU down to 1494 bytes, and the host is
unable to receive standard 1500-byte frames from the device.
Tested with the Linux USB Ethernet gadget.
Cc: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 2240eb4ae3dc4acff20d1a8947c441c451513e37 ]
This patch corrects a bug in function sky2_open() of the Marvell Yukon 2 driver
in which the settings for PHY quick link are overwritten.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Acked-by: Stephen Hemminger <shemminger@vyattta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 085f1afc56619bda424941412fdeaff1e32c21dc ]
If port 0 of a 5717 serdes device powers down, it hides the phy from
port 1. This patch works around the problem by keeping port 0's phy
powered up.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 5676cc7bfe1e388e87843f71daa229610385b41e ]
Some BIOS's don't setup power management correctly (what else is
new) and don't allow use of PCI Express power control. Add a special
exception module parameter to allow working around this issue.
Based on slightly different patch by Knut Petersen.
Reported-by: Arkadiusz Miskiewicz <arekm@maven.pl>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 09357b00255c233705b1cf6d76a8d147340545b8 upstream.
Based on the original patch submitted my Michael Wang
<wangyun@linux.vnet.ibm.com>.
Descriptors may not be write-back while checking TX hang with flag
FLAG2_DMA_BURST on.
So when we detect hang, we just flush the descriptor and detect
again for once.
-v2 change 1 to true and 0 to false and remove extra ()
CC: Michael Wang <wangyun@linux.vnet.ibm.com>
CC: Flavio Leitner <fbl@redhat.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5d5440a835710d09f0ef18da5000541ec98b537a upstream.
URB unlinking is always racing with its completion and tx_complete
may be called before or during running usb_unlink_urb, so tx_complete
must not clear urb->dev since it will be used in unlink path,
otherwise invalid memory accesses or usb device leak may be caused
inside usb_unlink_urb.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0956a8c20b23d429e79ff86d4325583fc06f9eb4 upstream.
Commit 4231d47e6fe69f061f96c98c30eaf9fb4c14b96d(net/usbnet: avoid
recursive locking in usbnet_stop()) fixes the recursive locking
problem by releasing the skb queue lock, but it makes usb_unlink_urb
racing with defer_bh, and the URB to being unlinked may be freed before
or during calling usb_unlink_urb, so use-after-free problem may be
triggerd inside usb_unlink_urb.
The patch fixes the use-after-free problem by increasing URB
reference count with skb queue lock held before calling
usb_unlink_urb, so the URB won't be freed until return from
usb_unlink_urb.
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Oliver Neukum <oliver@neukum.org>
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 62ebeed8d00aef75eac4fd6c161cae75a41965ca upstream.
This makes it possible to reload driver if insmod has failed due to
missing firmware.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 342bbf3fee2fa9a18147e74b2e3c4229a4564912 upstream.
If we only monitor while associated, the following
can happen:
- we're associated, and the queue stuck check
runs, setting the queue "touch" time to X
- we disassociate, stopping the monitoring,
which leaves the time set to X
- almost 2s later, we associate, and enqueue
a frame
- before the frame is transmitted, we monitor
for stuck queues, and find the time set to
X, although it is now later than X + 2000ms,
so we decide that the queue is stuck and
erroneously restart the device
It happens more with P2P because there we can
go between associated/unassociated frequently.
Reported-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a9b89e2567c743483e6354f64d7a7e3a8c101e9e upstream.
Driver rtl8192ce when used with the RTL8188CE device would start at about
20 Mbps on a 54 Mbps connection, but quickly drop to 1 Mbps. One of the
symptoms is that the AP would need to retransmit each packet 4 of 5 times
before the driver would acknowledge it. Recovery is possible only by
unloading and reloading the driver. This problem was reported at
https://bugzilla.redhat.com/show_bug.cgi?id=770207.
The problem is due to a missing update of the gain setting.
Signed-off-by: Jingjun Wu <jingjun_wu@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ebecdcc12fed5d3c81853dea61a0a78a5aefab52 upstream.
When driver rtl8192cu is used with the debug level set to 3 or greater,
the result is "sleeping function called from invalid context" due to
an rcu_read_lock() call in the DM refresh routine in driver rtl8192c.
This lock is not necessary as the USB driver does not use the struct
being protected, thus the lock is set only when a PCI interface is
active.
This bug is reported in https://bugzilla.kernel.org/show_bug.cgi?id=42775.
Reported-by: Ronald Wahl <ronald.wahl@raritan.com>
Tested-by: Ronald Wahl <ronald.wahl@raritan.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ronald Wahl <ronald.wahl@raritan.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7f66c2f93e5779625c10d262c84537427a2673ca upstream.
Handle previous allocation failures when freeing device memory
Signed-off-by: Simon Graham <simon.graham@virtualcomputer.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 76a92be537f1c8c259e393632301446257ca3ea9 upstream.
In https://bugzilla.redhat.com/show_bug.cgi?id=771656, a kernel bug was
triggered due to a failed skb allocation that was not checked. This event
lead to an audit of all memory allocations in the complete rtlwifi family
of drivers. This patch fixes the rest.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d42a179b941a9e4cc6cf41d0f3cbadd75fc48a89 upstream.
This is an RT3070 based device.
Reported-by: Mikhail Kryshen <mikhail@kryshen.net>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 210787e82a0ac1ffb5d7be1c796f0c51050849ad upstream.
On il3945_down procedure we free tx queue data and nullify il->txq
pointer. After that we drop mutex and then cancel delayed works. There
is possibility, that after drooping mutex and before the cancel, some
delayed work will start and crash while trying to send commands to
the device. For example, here is reported crash in
il3945_bg_reg_txpower_periodic():
https://bugzilla.kernel.org/show_bug.cgi?id=42766#c10
Patch fix problem by adding il->txq check on works that send commands,
hence utilize tx queue.
Reported-by: Clemens Eisserer <linuxhippy@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
commit 4e50391968849860dff1aacde358b4eb14aa5127 upstream.
This patch adds support for the Sitecom LN-031 USB adapter with a AX88178 chip.
Added USB id to find correct driver for AX88178 1000 Ethernet adapter.
Signed-off-by: Joerg Neikes <j.neikes@midlandgate.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
