| Age | Commit message (Collapse) | Author |
|---|
|
commit 862f0982eadcea0e114576c57ea426d3d51a69a6 upstream.
FEC_MMFR_OP_WRITE should be used than FEC_MMFR_OP_READ in
a mdio write operation.
It's probably a typo introduced by commit:
e6b043d512fa8d9a3801bf5d72bfa3b8fc3b3cc8
netdev/fec.c: add phylib supporting to enable carrier detection (v2)
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit a124339ad28389093ed15eca990d39c51c5736cc upstream.
We have found a hardware erratum on 82599 hardware that can lead to
unpredictable behavior when Header Splitting mode is enabled. So
we are no longer enabling this feature on affected hardware.
Please see the 82599 Specification Update for more information.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 3e9d08ec0a68f6faf718d5a7e050fe5ca0ba004f upstream.
Under harsh testing conditions, including low memory, the guest would
stop receiving packets. With this patch applied we no longer see any
problems in the driver while performing these tests for extended periods
of time.
Make sure napi is scheduled subsequent to each napi_enable.
Signed-off-by: Bruce Rogers <brogers@novell.com>
Signed-off-by: Olaf Kirch <okir@suse.de>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 3b5c5827d1f80ad8ae844a8b1183f59ddb90fe25 upstream.
P54_HDR_FLAG_DATA_OUT_SEQNR is meant to tell the
firmware that "the frame's sequence number has
already been set by the application."
Whereas IEEE80211_TX_CTL_ASSIGN_SEQ is set for
frames which lack a valid sequence number and
either the driver or firmware has to assign one.
Yup, it's the exact opposite!
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 5b64aa72ead6f8be488d2be7af579f0d69fb7a6e upstream.
The bit 6 & 7 of AR_WA (0x4004) should be enabled only
for the chips that are supporting L0s functionality
while resuming back from S3/S4.
Enabling these bits for AR9280 is causing system hang
within a few S3/S4-resume cycles.
Cc: Jack Lee <jlee@atheros.com>
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 6f4810101a629b31b5427872a09ea092cfc5c4bd upstream.
AR9003's PAPRD was enabled prematurely, and is causing some
large discrepancies on throughput and network connectivity.
For example downlink (RX) throughput against an AR9280 AP
can vary widlely from 43-73 Mbit/s while disabling this
gets AR9382 (2x2) up to around 93 Mbit/s in a 2.4 GHz HT20 setup.
Cc: Paul Shaw <paul.shaw@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 811ea256b30b37091b5bbf41517404cf98ab56c1 upstream.
The power detector adc offset calibration has to be done
on 4 minutes interval (longcal * pa_skip_count). But the commit
"ath9k_hw: fix a noise floor calibration related race condition"
makes the PA calibration executed more frequently beased on
nfcal_pending value. Running PAOffset calibration lesser than
longcal interval doesn't help anything and the worse part is that
it causes NF load timeouts and RX deaf conditions.
In a very noisy environment, where the distance b/w AP & station
is ~10 meter and running a downlink udp traffic with frequent
background scan causes "Timeout while waiting for nf to load:
AR_PHY_AGC_CONTROL=0x40d1a" and moves the chip into deaf state.
This issue was originaly reported in Android platform where
the network-manager application does bgscan more frequently
on AR9271 chips. (AR9285 family usb device).
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 1186488b4a4d4871e40cb1604ba3ede3d4b7cc90 upstream.
Restart the beacon timers only if the beacon
was already configured. Otherwise beacons timers
are restarted unnecessarily in unassociated state too.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit afe68d0a8f5961652e26cea39d74e2cc820de841 upstream.
ath9k supports its own set of virtual wiphys, and it uses
the mac80211 idle notifications to know when a device needs
to be idle or not. We recently changed ath9k to force idle
on driver stop() and on resume but forgot to take into account
ath9k's own virtual wiphy idle states. These are used internally
by ath9k to check if the device's radio should be powered down
on each idle call. Without this change its possible that the
device could have been forced off but the virtual wiphy idle
was left on.
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit a08e7ade9ddf4fe79576f953cc5c1725e944d26c upstream.
mac80211 will notify drivers when to go idle and ath9k
assumed that it would get further notifications for idle
states after a device stop() config call but as per agreed
semantics the idle state of the radio is left up to driver
after mac80211 issues the stop() callback. The driver is
resposnbile for ensuring the device remains idle after
that even between suspend / resume calls.
This fixes suspend/resume when you issue suspend and resume
twice on ath9k when ath9k_stop() was already called. We need
to put the radio to full sleep in order for resume to work
correctly.
What might seem fishy is we are turning the radio off
after resume. The reason why we do this is because we know
we should not have anything enabled after a mac80211 tells
us to stop(), if we resume and never get a start() we won't
get another stop() by mac80211 so to be safe always bring
the 802.11 device with the radio disabled after resume,
this ensures that if we suspend we already have the radio
disabled and only a start() will ever trigger it on.
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 39ec2997c374b528cdbf65099b6d6b8593a67f7f upstream.
There is a roundng error in delimiter padding computation
which causes severe throughput drop with some of AR9003.
signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 4bdd1e978ede034c1211957eb17eaf50de00d234 upstream.
The PCU lock should be used to contend TX DMA as well,
this will be done next.
This is part of a series of patches which fix stopping
TX DMA completley when requested on the driver.
For more details about this issue refer to this thread:
http://marc.info/?l=linux-wireless&m=128629803703756&w=2
Tested-by: Ben Greear <greearb@candelatech.com>
Cc: Kyungwan Nam <kyungwan.nam@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 9d94674ab754be0e275120a183670ead435f9c0d upstream.
The new PCU lock is better placed so we can just contend
against that when trying to reset hardware.
This is part of a series of patches which fix stopping
TX DMA completley when requested on the driver.
For more details about this issue refer to this thread:
http://marc.info/?l=linux-wireless&m=128629803703756&w=2
Tested-by: Ben Greear <greearb@candelatech.com>
Cc: Kyungwan Nam <kyungwan.nam@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
commit 52a0e2477dac2106bc1688cbe9615cdafc9deb7d upstream.
Improper configuration of 0x16288 and 0x16290 would affect transmission.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit ff8f59b5bbdf1527235b8c88d859c7d23691324f upstream.
When doing a channel change, the pending URBs have to be killed
properly on calling htc_stop().
This fixes the probe response timeout seen when sending UDP traffic at
a high rate and running background scan at the same time.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 3dd823e6b86407aed1a025041d8f1df77e43a9c8 upstream.
With commit 554d1d027b19265c4aa3f718b3126d2b86e09a08 only one RF_KILL
interrupt will be seen by the driver when the interface is down.
Re-enable the interrupt when it occurs to see all transitions.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 554d1d027b19265c4aa3f718b3126d2b86e09a08 upstream.
Since commit 6cd0b1cb872b3bf9fc5de4536404206ab74bafdd "iwlagn: fix
hw-rfkill while the interface is down", we enable interrupts when
device is not ready to receive them. However hardware, when it is in
some inconsistent state, can generate other than rfkill interrupts
and crash the system. I can reproduce crash with "kernel BUG at
drivers/net/wireless/iwlwifi/iwl-agn.c:1010!" message, when forcing
firmware restarts.
To fix only enable rfkill interrupt when down device and after probe.
I checked patch on laptop with 5100 device, rfkill change is still
passed to user space when device is down.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 2f32c867219734b06abc980d4812f67b6d6fe517 upstream.
Commit 3f5a2a713aad28480d86b0add00c68484b54febc zeroes out the statistics
message block (SMB) and coalescing message block (CMB) when adapter ring
resources are freed. This is desirable behavior, but, as a side effect,
the commit leads to an oops when atl1_set_ringparam() attempts to alter
the number of rx or tx elements in the ring buffer (by using ethtool
-G, for example). We don't want SMB or CMB to change during this
operation.
Modify atl1_set_ringparam() to preserve SMB and CMB when changing ring
parameters.
Signed-off-by: Jay Cliburn <jcliburn@gmail.com>
Reported-by: Tõnu Raitviir <jussuf@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 9c4cf6d94fb362c27a24df5223ed6e327eb7279a upstream.
This patch adds the device id for the windy31 USB device to the rt73usb
driver.
Thanks to Ralf Flaxa for reporting this and providing testing and a
sample device.
Reported-by: Ralf Flaxa <rf@suse.de>
Tested-by: Ralf Flaxa <rf@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
commit 229bd792be0bad245b78ed8f119952733a4752e5 upstream.
The interrupt handler takes a lock - but since commit bcad6e80f3f this
lock goes through an indirection specified in the hermes_t structure.
We must therefore initialise the structure before setting up the
interrupt handler.
Fix orinoco_cs and spectrum_cs
<https://bugzilla.kernel.org/show_bug.cgi?id=23932>
Bisected by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 56e6417b49132d4f56e9f2241d31942b90b46315 upstream.
This USB ID is for the WUBI-100GW 802.11g Wireless LAN USB Device that
uses p54usb.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Eduardo Costa <ecosta.tmp@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 16cad7fba037b34ca32cc0adac65bc089d969fb8 upstream.
This patch adds five more USBIDs to the table.
Source:
http://www.linuxant.com/pipermail/driverloader/2005q3/002307.html
http://wireless.kernel.org/en/users/Drivers/p54/devices (by M. Davis)
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 8d1331b37d5b656a7a8e561f8e9d7661dd00c910 upstream.
During initialization each driver reads the default TX power
for each individual channel. However mac80211 only accepts the
maximum value (which is also handled as default value).
As a result, the TX power of the device was being limited to
the default value, which is often quite low compared to the
real maximum acceptable value.
This patch allows each driver to set the maximum value on a
per-channel basis which is forwarded to mac80211. The default
value will be preserved for now, in case we want to update
mac80211 to differentiate between the maximum and default txpower.
This fixes bug complaining about limited TX power values like:
https://bugzilla.kernel.org/show_bug.cgi?id=16358
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit ba34fcee476d11e7c9df95932787a22a96ff6e68 upstream.
... and interface up.
In these situations, you are usually trying to connect to a new AP, so
keeping TKIP countermeasures active is confusing. This is already how
the driver behaves (inadvertently). However, querying SIOCGIWAUTH may
tell userspace that countermeasures are active when they aren't.
Clear the setting so that the reporting matches what the driver has
done..
Signed-off by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 0a54917c3fc295cb61f3fb52373c173fd3b69f48 upstream.
Enable the port when disabling countermeasures, and disable it on
enabling countermeasures.
This bug causes the response of the system to certain attacks to be
ineffective.
It also prevents wpa_supplicant from getting scan results, as
wpa_supplicant disables countermeasures on startup - preventing the
hardware from scanning.
wpa_supplicant works with ap_mode=2 despite this bug because the commit
handler re-enables the port.
The log tends to look like:
State: DISCONNECTED -> SCANNING
Starting AP scan for wildcard SSID
Scan requested (ret=0) - scan timeout 5 seconds
EAPOL: disable timer tick
EAPOL: Supplicant port status: Unauthorized
Scan timeout - try to get results
Failed to get scan results
Failed to get scan results - try scanning again
Setting scan request: 1 sec 0 usec
Starting AP scan for wildcard SSID
Scan requested (ret=-1) - scan timeout 5 seconds
Failed to initiate AP scan.
Reported by: Giacomo Comes <comes@naic.edu>
Signed-off by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 667c78afaec0ac500908e191e8f236e9578d7b1f upstream.
Without this, gcc 4.5 won't compile xen-netfront and xen-blkfront, where
this is being used to specify array sizes.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
[ Upstream commit 2a27a03d3a891e87ca33d27a858b4db734a4cbab ]
__pppoe_xmit function return value was invalid resulting in
additional call to kfree_skb on already freed skb. This resulted in
memory corruption and consequent kernel panic after PPPoE peer
terminated the link.
This fixes commit 55c95e738da85373965cb03b4f975d0fd559865b.
Reported-by: Gorik Van Steenberge <gvs@zemos.net>
Reported-by: Daniel Kenzelmann <kernel.bugzilla@kenzelmann.dyndns.info>
Reported-by: Denys Fedoryshchenko <nuclearcat@nuclearcat.com>
Reported-by: Pawel Staszewski <pstaszewski@artcom.pl>
Diagnosed-by: Andrej Ota <andrej@ota.si>
Diagnosed-by: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Denys Fedoryshchenko <nuclearcat@nuclearcat.com>
Tested-by: Pawel Staszewski <pstaszewski@artcom.pl>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: Andrej Ota <andrej@ota.si>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
[ Upstream commit 46814e08d80f87449b5adb3d549a3cae6f9f8148 ]
My conversion of tehuti to use request_firmware() was confused about
the filename of the firmware blob. Change the driver to match the
blob.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
[ Upstream commit 75c1c82566f23dd539fb7ccbf57a1caa7ba82628 ]
If we break the loop when there are still skbs in tq and no skb in
rq, the skbs will be left in txq until new skbs are enqueued into rq.
In rare cases, no new skb is queued, then these skbs will stay in rq
forever.
After this patch, if tq isn't empty when we break the loop, we goto
resched directly.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
[ Upstream commit af3e5bd5f650163c2e12297f572910a1af1b8236 ]
The returned slave is incorrect, if the net device under check is not
charged yet by the master.
Signed-off-by: Hillf Danton <dhillf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
[ Upstream commit 3fd40d0ceac9c234243730f4d7a6ffdb2fd3023a ]
Regarding benet be_cmd_multicast_set() function, now using
netdev_for_each_mc_addr() helper for mac address copy, but
when copying to req->mac[] did not increase of the index.
Cc: Sathya Perla <sathyap@serverengines.com>
Cc: Subbu Seetharaman <subbus@serverengines.com>
Cc: Sarveshwar Bandi <sarveshwarb@serverengines.com>
Cc: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: Joe Jin <joe.jin@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
[ Upstream commit ea80907ff066edd1dd43c5fe90ae6677d15e6384 ]
As device_set_wakeup_enable can now sleep, move the call to outside
the critical section.
Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Andrew Hendry <andrew.hendry@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
[ Upstream commit 24b7ea9f6c9787fad885442ed0cc010f1aa69cca ]
I am not family with RealTek RTL-8139C+ series 10/100 PCI Ethernet driver.
I try to guess the meaning of RxProtoIP and IPFail.
RxProtoIP stands for received IPv4 packet that upper protocol is not tcp and udp.
!(status & IPFail) is true means that driver correctly to check checksum in IPv4 header.
If these are right, driver will set ip_summed with CHECKSUM_UNNECESSARY for other
upper protocol, e.g. sctp, igmp protocol. This will cause protocol stack ignores
checksum check for packets with invalid checksum.
This patch is only compile-test.
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 841051602e3fa18ea468fe5a177aa92b6eb44b56 upstream.
The ath9k driver subtracts 3 dBm to the txpower as with two radios the
signal power is doubled.
The resulting value is assigned in an u16 which overflows and makes
the card work at full power.
Signed-off-by: Matteo Croce <matteo@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit e702ba18f25887c76d26c8a85cc1706463c62e9a upstream.
Parsing data using bitfields is messy, because it makes endian handling
much harder. AR9002 and earlier got it right, AR9003 got it wrong.
This might lead to either using too high or too low tx power values,
depending on frequency and eeprom settings.
Fix it by getting rid of the CTL related bitfields entirely and use
masks instead.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 9306990a656d9cfd8bf3586938012729c1f2ea50 upstream.
The register which gives input gpio state is 0x404c for ar9003,
currently 0x4048 is wrongly used. This will disable RF and make
it unusable on some of AR9003.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 916448e77f6bcaaa7f13c3de0c3851783ae2bfd0 upstream.
AR_RxKeyIdxValid will not be set for bcast/mcast frames and so relying
this status for MIC failed frames is buggy.
Due to this, MIC failure events for broadcast frames are not sent to
supplicant resulted in AP disconnecting the STA.
Able to pass Wifi Test case 5.2.18 with this fix.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 46047784b8cdcfc916f6c1cccee0c18dd1223dfd upstream.
while removing beaconing mode interface, SWBA interrupt
was never disabled when there are no other beaconing interfaces.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit d5d3ebe3be5c5123f2d444e186717f45284151e2 upstream.
If r8196 received packets with invalid sctp/igmp(not tcp, udp) checksum, r8196 set skb->ip_summed
wit CHECKSUM_UNNECESSARY. This cause that upper protocol don't check checksum field.
I am not family with r8196 driver. I try to guess the meaning of RxProtoIP and IPFail.
RxProtoIP stands for received IPv4 packet that upper protocol is not tcp and udp.
!(opts1 & IPFail) is true means that driver correctly to check checksum in IPv4 header.
If it's right, I think we should not set ip_summed wit CHECKSUM_UNNECESSARY for my sctp packets
with invalid checksum.
If it's not right, please tell me.
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 53f57357ff0afc37804f4e82ee3123e0c0a2cad6 upstream.
The original patch helps under obscure conditions (no pun) but
some 8168 do not like it. The change needs to be tightened with
a specific 8168 version.
This reverts commit 801e147cde02f04b5c2f42764cd43a89fc7400a2
("r8169: Handle rxfifo errors on 8168 chips").
Regression at https://bugzilla.kernel.org/show_bug.cgi?id=20882
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Tested-by: Andreas Radke <a.radke@arcor.de>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Daniel J Blueman <daniel.blueman@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit fccec10b33503a2b1197c8e7a3abd30443bedb08 upstream.
Fix switching device to low-speed mode after resume reported in:
https://bugzilla.redhat.com/show_bug.cgi?id=502974
Reported-and-tested-by: Laurentiu Badea <bugzilla-redhat@wotevah.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit adea1ac7effbddbe60a9de6d63462bfe79289e59 upstream.
While porting GRO to r8169, I found this driver has a bug in its rx
path.
All skbs given to network stack had their ip_summed set to
CHECKSUM_NONE, while hardware said they had correct TCP/UDP checksums.
The reason is driver sets skb->ip_summed on the original skb before the
copy eventually done by copybreak. The fresh skb gets the ip_summed =
CHECKSUM_NONE value, forcing network stack to recompute checksum, and
preventing my GRO patch to work.
Fix is to make the ip_summed setting after skb copy.
Note : rx_copybreak current value is 16383, so all frames are copied...
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit d47844a014fada1a788719f6426bc7044f2a0fd8 upstream.
It seems that using ath9k_hw_stoppcurecv to stop rx dma is not enough.
When it's time to stop DMA, the PCU is still busy, so the rx enable
bit never clears.
Using ath9k_hw_abortpcurecv helps with getting rx stopped much faster,
with this change, I cannot reproduce the rx stop related WARN_ON anymore.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit ab08853fab2093e5c6f5de56827a4c93dce4b055 upstream.
VMWare reports that the e1000 driver has a bug when bringing down the
interface, such that interrupts are not disabled in the hardware but the
driver stops reporting that it consumed the interrupt.
The fix is to set the driver's "down" flag later in the routine,
after all the timers and such have exited, preventing the interrupt
handler from being called and exiting early without handling the
interrupt.
CC: Anupam Chanda <anupamc@vmware.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit b0786b430c982dffbb44d8030e6b6088671ce745 upstream.
Since usbnet already took usb runtime pm, we have to
enable runtime pm for usb interface of usbnet, otherwise
usb_autopm_get_interface may return failure and cause
'ifconfig usb0 up' failed if USB_SUSPEND(RUNTIME_PM) is
enabled.
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Joe Perches <joe@perches.com>
Cc: Oliver Neukum <oliver@neukum.org>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit e476a5a41ad67d0e2b4a652820c49a3923eb936b upstream.
Fix unbalanced call to sdio_release_host() on the error path.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 9f2a0fac625bcef9c579bcf0b0c904ab1a56e7c4 upstream.
On module removal, the sdio version of b43 generates the following warning:
[ 851.560519] ------------[ cut here ]------------
[ 851.560531] WARNING: at drivers/mmc/core/core.c:237 mmc_wait_for_cmd+0x88/0x90()
[ 851.560534] Hardware name: 20552PG
[ 851.560536] Modules linked in: b43(-) ssb mmc_block binfmt_misc rfcomm sco bnep ppdev l2cap ipt_MASQUERADE iptable_nat nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 xt_state nf_conntrack ipt_REJECT xt_tcpudp iptable_filter ip_tables x_tables bridge stp kvm_intel kvm arc4 iwlagn snd_hda_codec_conexant snd_hda_intel snd_hda_codec iwlcore snd_hwdep snd_pcm thinkpad_acpi mac80211 snd_seq_midi snd_rawmidi snd_seq_midi_event snd_seq r852 joydev snd_timer sm_common pcmcia nand snd_seq_device cfg80211 sdhci_pci btusb psmouse tpm_tis yenta_socket nand_ids lp snd pcmcia_rsrc nand_ecc bluetooth sdhci tpm pcmcia_core parport mtd snd_page_alloc serio_raw tpm_bios soundcore nvram led_class sha256_generic aes_i586 aes_generic dm_crypt i915 drm_kms_helper drm ahci intel_agp i2c_algo_bit intel_gtt e1000e libahci video agpgart output
[ 851.560620] Pid: 2504, comm: rmmod Not tainted 2.6.36-titan0+ #1
[ 851.560622] Call Trace:
[ 851.560631] [<c014a102>] warn_slowpath_common+0x72/0xa0
[ 851.560636] [<c04d94c8>] ? mmc_wait_for_cmd+0x88/0x90
[ 851.560641] [<c04d94c8>] ? mmc_wait_for_cmd+0x88/0x90
[ 851.560645] [<c014a152>] warn_slowpath_null+0x22/0x30
[ 851.560649] [<c04d94c8>] mmc_wait_for_cmd+0x88/0x90
[ 851.560655] [<c0401585>] ? device_release+0x25/0x80
[ 851.560660] [<c04df210>] mmc_io_rw_direct_host+0xa0/0x150
[ 851.560665] [<c04df370>] mmc_io_rw_direct+0x30/0x40
[ 851.560669] [<c04e06e7>] sdio_disable_func+0x37/0xa0
[ 851.560683] [<f8dfcb80>] b43_sdio_remove+0x30/0x50 [b43]
[ 851.560687] [<c04df8cc>] sdio_bus_remove+0x1c/0x60
[ 851.560692] [<c016d39f>] ? blocking_notifier_call_chain+0x1f/0x30
[ 851.560697] [<c0404991>] __device_release_driver+0x51/0xb0
[ 851.560701] [<c0404a7f>] driver_detach+0x8f/0xa0
[ 851.560705] [<c0403c83>] bus_remove_driver+0x63/0xa0
[ 851.560709] [<c0405039>] driver_unregister+0x49/0x80
[ 851.560713] [<c0405039>] ? driver_unregister+0x49/0x80
[ 851.560718] [<c04dfad7>] sdio_unregister_driver+0x17/0x20
[ 851.560727] [<f8dfcb42>] b43_sdio_exit+0x12/0x20 [b43]
[ 851.560734] [<f8dfe76f>] b43_exit+0x17/0x3c [b43]
[ 851.560740] [<c017fb8d>] sys_delete_module+0x13d/0x200
[ 851.560747] [<c01fd7d2>] ? do_munmap+0x212/0x300
[ 851.560752] [<c010311f>] sysenter_do_call+0x12/0x28
[ 851.560757] ---[ end trace 31e14488072d2f7d ]---
[ 851.560759] ------------[ cut here ]------------
The warning is caused by b43 not claiming the device before calling
sdio_disable_func().
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Arnd Hannemann <arnd@arndnet.de>
Tested-by: Arnd Hannemann <arnd@arndnet.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 62391f97babb7fe0c769830b6f0e0bd184bd0704 upstream.
pcnet_cs:
add new_id: "corega Ether CF-TD" 10Base-T PCMCIA card.
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit be8c648051048bc66fbca590d00f3e8543ec32af upstream.
Commit c477d0447db08068a497e7beb892b2b2a7bff64b added support for RGMII
rx/tx delays except that it ends up clearing rx/tx delays bit for modes
differents that RGMII*ID. Due to this, ethernet is not working anymore
on my guruplug server +. This patch is fixing that.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 5e848f789d60000d39d9a5f26ab02dbdd963f6cd upstream.
Apart from locking the start and stop PCU we need
to ensure we also content starting and stopping the PCU
between hardware resets.
This is part of a series that will help resolve the bug:
https://bugzilla.kernel.org/show_bug.cgi?id=14624
For more details about this issue refer to:
http://marc.info/?l=linux-wireless&m=128629803703756&w=2
Cc: Ben Greear <greearb@candelatech.com>
Cc: Kyungwan Nam <kyungwan.nam@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
