| Age | Commit message (Collapse) | Author |
|---|
|
commit a3f92eea04101d9a8e14d50f8048cc5b7bca07a8 upstream.
This patch converts bcm63xx_enet to uset get_sset_count
like the other drivers do.
Signed-off-by: Florian Fainelli <ffainelli@freebox.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 52ce3e9a7db754b78cf2cbabc87013f921b25b28 upstream.
Add PCI .shutdown method so that we can disable the device during
shutdown or reboot. Without this, the reboot doesn't work well on
some platforms.
This fixes http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2124
Tested-by: pablo <pablolm2005@gmail.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This is a backport of upstream commit: e8c6342d989e241513baeba4b05a04b6b1f3bc8b
This patch fixes a bug in ath9k's tx status check, which
caused mac80211 to consider regularly transmitted unicast frames
as un-acked.
When checking the ts_status field for errors, it needs to be masked
with ATH9K_TXERR_FILT, because this field also contains other fields
like ATH9K_TX_ACKED.
Without this patch, AP mode is pretty much unusable, as hostapd
checks the ACK status for the frames that it injects.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This is a backport of upstream commit: f4709fdf683e1ed37b321c258b614ebe39752bf3
Atheros single stream AR9285 and AR9271 have half the PCU TX FIFO
buffer size of that of dual stream devices. Dual stream devices
have a max PCU TX FIFO size of 8 KB while single stream devices
have 4 KB. Single stream devices have an issue though and require
hardware only to use half of the amount of its capable PCU TX FIFO
size, 2 KB and this requires a change in software.
Technically a change would not have been required (except for frame
burst considerations of 128 bytes) if these devices would have been
able to use the full 4 KB of the PCU TX FIFO size but our systems
engineers recommend 2 KB to be used only. We enforce this through
software by reducing the max frame triggger level to 2 KB.
Fixing the max frame trigger level should then have a few benefits:
* The PER will now be adjusted as designed for underruns when the
max trigger level is reached. This should help alleviate the
bus as the rate control algorithm chooses a slower rate which
should ensure frames are transmitted properly under high system
bus load.
* The poll we use on our TX queues should now trigger and work
as designed for single stream devices. The hardware passes
data from each TX queue on the PCU TX FIFO queue respecting each
queue's priority. The new trigger level ensures this seeding of
the PCU TX FIFO queue occurs as designed which could mean avoiding
false resets and actually reseting hw correctly when a TX queue
is indeed stuck.
* Some undocumented / unsupported behaviour could have been triggered
when the max trigger level level was being set to 4 KB on single
stream devices. Its not clear what this issue was to me yet.
Cc: Kyungwan Nam <kyungwan.nam@atheros.com>
Cc: Bennyam Malavazi <bennyam.malavazi@atheros.com>
Cc: Stephen Chen <stephen.chen@atheros.com>
Cc: Shan Palanisamy <shan.palanisamy@atheros.com>
Cc: Paul Shaw <paul.shaw@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This is a backport of upstream commit: e7824a50662f7f79b1a739f705b4d906c31cf221
When mac80211 was telling us to go into Powersave we listened
and immediately turned RX off. This meant hardware would not
see the ACKs from the AP we're associated with and hardware
we'd end up retransmiting the null data frame in a loop
helplessly.
Fix this by keeping track of the transmitted nullfunc frames
and only when we are sure the AP has sent back an ACK do we
go ahead and shut RX off.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Vivek Natarajan <Vivek.Natarajan@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This is a backport of upstream commit: 332c556633b8c5fb4e890b1783122f2315526590
When TX is hung, the chip is reset. Ensure that
the chip is awake by using the PS wrappers.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 316a4d966cae3c2dec83ebb1ee1a3515f97b30ff upstream.
For PPC architecture with PHY Revision < 3, a read of the register
B43_MMIO_HWENABLED_LO will cause a CPU fault unless b43legacy_status()
returns a value of 2 (B43legacy_STAT_STARTED); however, one finds that
the driver is unable to associate after resuming from hibernation unless
this routine returns 1. To satisfy both conditions, the routine is rewritten
to return TRUE whenever b43legacy_status() returns a value < 2.
This patch fixes the second problem listed in the postings for Red Hat
Bugzilla #538523.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
[ Upstream commit: e0188829cb724e7d12a2d4e343b368ff1d6e1471 ]
About 50% of shutdowns of b44 Ethernet adapter ends by kernel panic
with kernels compiled with stack-protector.
Checking b44_magic_pattern() return values, one call of
b44_magic_pattern() returns 127. It means, that set_bit(128, pmask)
was called on line 1509. It means that bit 0 of 17th byte of pmask was
overwritten. But pmask has only 16 bytes. Stack corruption happens.
It seems that set_bit() on line 1509 always writes one bit off.
The fix does not only solve the stack corruption, but also makes Wake
On LAN working on my onboard B44 on Asus A7V-333X mainboard.
It seems that this problem affects all kernel versions since commit
725ad800 ([PATCH] b44: add wol for old nic) on 2006-06-20.
Signed-off-by: Stanislav Brabec <sbrabec@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 70d57139f932b9ca21026253d02af71cf53d764a upstream.
There are different bits used to convey the setting of the rfkill
switch to the driver. The current driver only supports one of these
possibilities. These changes were derived from the latest version
of the vendor driver.
This patch fixes the regression noted in kernel Bugzilla #14743.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-and-tested-by: Antti Kaijanmäki <antti@kaijanmaki.net>
Tested-by: Hin-Tak Leung <hintak.leung@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 512414b0bed0d376ac4d5ec1dd6f0b1a3551febc upstream.
Without this we have no gaurantee of the integrity of the
EEPROM and are likely to encounter a lot of bogus bug reports
due to actual issues on the EEPROM. With the EEPROM checksum
check in place we can easily rule those issues out.
If you run patch during a revert *you* have a card with a busted
EEPROM and only older kernel will support that concoction. This
patch is a trade off between not accepitng bogus EEPROMs and
avoiding bogus bug reports allowing developers to focus instead
on real concrete issues.
If stable keeps bogus bug reports because of a possibly busted EEPROM
feel free to apply this there too.
Tested on an AR5414
Cc: jirislaby@gmail.com
Cc: akpm@linux-foundation.org
Cc: rjw@sisk.pl
Cc: me@bobcopeland.com
Cc: david.quan@atheros.com
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 2eb2fa67e5462a36e98172fb92c78bc405b3035f upstream.
As a holdover from earlier code when we used to set
the power limit to '0' after a reset to configure the
default transmit power, ath5k interprets txpower=0 as
12.5 dBm. Fix that by just passing 0 through.
This fixes http://bugzilla.kernel.org/show_bug.cgi?id=14567
Reported-by: Daniel Folkers <daniel.folkers@task24.nl>
Tested-by: Daniel Folkers <daniel.folkers@task24.nl>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
* 'security' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6:
mac80211: fix spurious delBA handling
mac80211: fix two remote exploits
|
|
Lennert Buytenhek noticed that delBA handling in mac80211
was broken and has remotely triggerable problems, some of
which are due to some code shuffling I did that ended up
changing the order in which things were done -- this was
commit d75636ef9c1af224f1097941879d5a8db7cd04e5
Author: Johannes Berg <johannes@sipsolutions.net>
Date: Tue Feb 10 21:25:53 2009 +0100
mac80211: RX aggregation: clean up stop session
and other parts were already present in the original
commit d92684e66091c0f0101819619b315b4bb8b5bcc5
Author: Ron Rindjunsky <ron.rindjunsky@intel.com>
Date: Mon Jan 28 14:07:22 2008 +0200
mac80211: A-MPDU Tx add delBA from recipient support
The first problem is that I moved a BUG_ON before various
checks -- thereby making it possible to hit. As the comment
indicates, the BUG_ON can be removed since the ampdu_action
callback must already exist when the state is != IDLE.
The second problem isn't easily exploitable but there's a
race condition due to unconditionally setting the state to
OPERATIONAL when a delBA frame is received, even when no
aggregation session was ever initiated. All the drivers
accept stopping the session even then, but that opens a
race window where crashes could happen before the driver
accepts it. Right now, a WARN_ON may happen with non-HT
drivers, while the race opens only for HT drivers.
For this case, there are two things necessary to fix it:
1) don't process spurious delBA frames, and be more careful
about the session state; don't drop the lock
2) HT drivers need to be prepared to handle a session stop
even before the session was really started -- this is
true for all drivers (that support aggregation) but
iwlwifi which can be fixed easily. The other HT drivers
(ath9k and ar9170) are behaving properly already.
Reported-by: Lennert Buytenhek <buytenh@marvell.com>
Cc: stable@kernel.org
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Fixes kernel bugzilla #14691
Due to the way netpoll works, it is perfectly legal to see
NAPI already scheduled when new device events are pending
in b44_interrupt().
So logging a message about it is wrong and in fact harmful.
Based upon a patch by Andreas Mohr.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The other paths all drop chan->wsem. This was found by a static
checker (smatch).
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Jan "Yenya" Kasprzak <kas@fi.muni.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If we happen to have registered the driver without passing
a MAC address, we will print a zero MAC address and register
the interface with this invalid address, this is confusin. This
patch moves the checking of a valid ethernet address and the
generation of a random one down from the open function to
the probe function.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
smc91x.h defines SMC_IRQ_FLAGS to be -1 when it wants the interrupt
flags to be taken from the resource structure. However, d280ead
changed this to checking for non-zero resource flags.
Unfortunately, this means that on some platforms, we end up passing
'-1' to request_irq rather than the desired result. Combine the two
conditions into one so that the IRQ flags are taken from the resource
if either SMC_IRQ_FLAGS is -1 or the resource flags specify an
interrupt trigger.
This restores network on at least the Versatile platform.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes a null pointer dereference BUG() if ethtool is used on
an smsc9420 interface while it is down, because the phy_dev is only
allocated while the interface is up.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The newer chipsets (all PCI-E) are known that they need full power cycle
(AC or battery removal) to reset MAC address to a hardwired one. Previous
patch to address this problem loads the original MAC address from EEPROM.
But it brought other problem for which it is necessary to introduce a new
module parameter.
However, it might suffice to restore the initial MAC address before
shutdown/reboot/kexec and when removing the module.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
pci_alloc_consistent uses GFP_ATOMIC allocation that may fail on some systems
with limited memory (Bug #14265). pci_pool_alloc allows waiting with
GFP_KERNEL.
Tested-by: Karol Lewandowski <karol.k.lewandowski@gmail.com>
Signed-off-by: Roger Oksanen <roger.oksanen@cs.helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
gso_max_size must be set based on the value of the underlying device to
support devices not using the full 64k.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
Copied from original one-line patch here:
http://bugzilla.kernel.org/show_bug.cgi?id=14267#c26
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Fix soft-lockup in hso.c which is triggered on SMP machine when
modem is removed while file descriptor(s) under /dev are still open:
old version called kref_put() too early which resulted in destroying
hso_serial and hso_device objects which were still used later on.
Signed-off-by: Antti Kaijanmäki <antti.kaijanmaki@nomovok.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Antti Kaijanmäki <antti.kaijanmaki@nomovok.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the external timer cannot be used the driver
will continue to work without mitigation.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Andreas Lohre reported that the driver crashes when trying
to register_netdev(), he sugessted to move dev->netdev_ops initialization
before calling register_netdev(), it worked for him.
Reported-by: Andreas Lohre <alohre@gmail.com>
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
o Along with netdev->perm_addr, mac address will be
maintained in device private structure.
o Device limitation: We need to set mac address when ever
interface comes up.
In ALB/TAL mode, bonding driver calls set_mac for all slave with bond mac address.
But bonding driver set netdev->dev_addr field to its original value,
after enslaving interfaces.
When ever active slave changes, it swap dev_addr of inactive slave with active.
Yet it doesn't notify driver about change in netdev->dev_addr.
As netxen driver need to set mac addr when ever interface comes up,
it can't rely on netdev->dev_addr field. Specially in case of bonding mode ALB/TLB.
Signed-off-by: Narender Kumar <narender.kumar@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Kernel crashes, if promisc mode set without disabling rx queue.
Before changing mode in NX2031 chip, wait till rx queue drains.
Signed-off-by: Narender Kumar <narender.kumar@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Avoid resetting memory during initialization, skip this memory
block during driver probe.
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use BIT for macro definitions wherever possible, remove
unused and redundant macros.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Summary of Changes:
-Fix to receive multicast packets by setting the corresponding hardware
bit during initialization.
-Fix to re-enable the interface [by interface up command(ifup)] while the
interface is down.
-Fix to be able to down the interface by passing the last parameter
correctly to request_irq().
-Remove to read 4 extra bytes from the receiving queue after reading a
packet, even though it does not cause a predictable issue now.
-Remove occurrences of transmission done interrupt in order to tx
throughput enhancement.
-Enable IP checksum for packet receiving by setting the corresponding
hardware bit during initialization.
-Relocate ks_enable_int()/ks_disable_int() in order not to declare those
functions at the beginning of the file.
-Rename ks_enable()/_disable() to ks_enable_qmu()/ks_disable_qmu() in
order to give more meaningful names and relocate them not declaire
those functions at the beginning of the file.
Signed-off-by: David J. Choi <david.choi@micrel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When building for Sun 3:
drivers/net/ethoc.c:1091: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `ethoc_probe':
drivers/net/ethoc.c:965: undefined reference to `dma_alloc_coherent'
drivers/net/ethoc.c:1063: undefined reference to `dma_free_coherent'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When configuring the OEM bits in the PHY on 82577/82578, do not restart
autonegotiation if the firmware is blocking it (e.g. when an IDE-R session
is active) because the link must not go down.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A workaround for pre-release versions of 82577 is causing link issues on
some switches. The workaround is no longer needed on production parts so
remove it.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When changing MTU, save it off prior to resetting otherwise the flow control
thresholds may be miscalculated.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On some devices (e.g. 82578) not having a Tx timeout factor when linked at
100Mbps can cause false reports of hardware hangs on busy hubs.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When flow control (pause) parameters were changed via ethtool (i.e. enabled
or disabled), the newly calculated thresholds were not being written to the
device for non-fiber media.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove unnecessary workaround that mistakenly does not perform a page
select operation for PHY registers 29 and 30 (assuming these are the PHY
debug port address and data registers) on 82578 which can cause reads
of the Transmit with No Carrier Sense statistics register on page 778 to be
read from an incorrect page. Also error out if the page select operation
fails.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 3ec2a2b80f3eb53851fe4cef9e65b5d33376ef89 broke Tx/Rx when using
jumbo frames on certain parts (i.e. only PAUSE frames could be exchanged
once the high water mark was reached preventing normal packet traffic).
This patch reverts the breakage and sets appropriate high and low water
marks of the Rx FIFO for 82577/82578 which require a workaround due to a
flow control issue in hardware.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tc is required by CONFIG_IXGBE_DCB.
This also fixes compilation warning:
drivers/net/ixgbe/ixgbe_main.c: In function ‘ixgbe_tx_is_paused’:
drivers/net/ixgbe/ixgbe_main.c:245: warning: unused variable ‘tc’
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
veth_get_stats() can be called in parallel on several cpus.
It's better to not reset dev->stats as it could give wrong result on
one cpu. Use temporary variables, then store the final results.
Also, we should loop on every possible cpus, not only online cpus,
or cpu hotplug can suddenly give wrong veth stats.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (42 commits)
cxgb3: fix premature page unmap
ibm_newemac: Fix EMACx_TRTR[TRT] bit shifts
vlan: Fix register_vlan_dev() error path
gro: Fix illegal merging of trailer trash
sungem: Fix Serdes detection.
net: fix mdio section mismatch warning
ppp: fix BUG on non-linear SKB (multilink receive)
ixgbe: Fixing EEH handler to handle more than one error
net: Fix the rollback test in dev_change_name()
Revert "isdn: isdn_ppp: Use SKB list facilities instead of home-grown implementation."
TI Davinci EMAC : Fix Console Hang when bringing the interface down
smsc911x: Fix Console Hang when bringing the interface down.
mISDN: fix error return in HFCmulti_init()
forcedeth: mac address fix
r6040: fix version printing
Bluetooth: Fix regression with L2CAP configuration in Basic Mode
Bluetooth: Select Basic Mode as default for SOCK_SEQPACKET
Bluetooth: Set general bonding security for ACL by default
r8169: Fix receive buffer length when MTU is between 1515 and 1536
can: add the missing netlink get_xstats_size callback
...
|
|
unmap Rx page only when guaranteed that this page won't be
used anymore to allocate rx page chunks.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The TRT bit shifts were reversed for EMAC4 and non-EMAC4 during the
port from ibm_emac to ibm_newemac. This patch corrects that error.
Signed-off-by: Dave Mitchell <dmitchell@appliedmicro.com>
Acked-by: Feng Kan <fkan@appliedmicro.com>
Acked-by: Prodyut Hazarika <phazarika@appliedmicro.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We need to look for the 'shared-pins' property to get
this right.
Based upon a patch by Hermann Lauer.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This fixes the following warning:
WARNING: drivers/net/phy/built-in.o(.devexit.text+0x70): Section mismatch in reference from the function .mdio_gpio_bus_destroy() to the function .devinit.text:.mdio_gpio_bus_deinit()
The function __devexit .mdio_gpio_bus_destroy() references
a function __devinit .mdio_gpio_bus_deinit().
This is often seen when error handling in the exit function
uses functionality in the init path.
The fix is often to remove the __devinit annotation of
.mdio_gpio_bus_deinit() so it may be used outside an init section.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PPP does not correctly call pskb_may_pull() on all necessary receive paths
before reading the PPP protocol, thus causing PPP to report seemingly
random 'unsupported protocols' and eventually trigger BUG_ON(skb->len <
skb->data_len) in skb_pull_rcsum() when receiving multilink protocol in
non-linear skbs.
ppp_receive_nonmp_frame() does not call pskb_may_pull() before reading the
protocol number. For the non-mp receive path this is not a problem, as
this check is done in ppp_receive_frame(). For the mp receive path,
ppp_mp_reconstruct() usually copies the data into a new linear skb.
However, in the case where the frame is made up of a single mp fragment,
the mp header is pulled and the existing skb used. This skb was then
passed to ppp_receive_nonmp_frame() without checking if the encapsulated
protocol header could safely be read.
Signed-off-by: Ben McKeegan <ben@netservers.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After commmit 4b77b0a2ba27d64f58f16d8d4d48d8319dda36ff EEH breaks
after the second error, since it calls pci_restore_state()
but it returns 0, since pci->state_saved is false.
So, this patch just call pci_save_state() after pci_restore_state().
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
