aboutsummaryrefslogtreecommitdiff
path: root/drivers/net/wireless
AgeCommit message (Collapse)Author
2011-01-18iwlwifi: fix valid chain reading from EEPROMWey-Yi Guy
When read valid tx/rx chains from EEPROM, there is a bug to use the tx chain value for both tx and rx, the result of this cause low receive throughput on 1x2 devices becuase rx will only utilize single chain instead of two chains Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-18ath5k: fix locking in tx_complete_poll_workBob Copeland
ath5k_reset must be called with sc->lock. Since the tx queue watchdog runs in a workqueue and accesses sc, it's appropriate to just take the lock over the whole function. Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-17ath9k_hw: do PA offset calibration only on longcal intervalRajkumar Manoharan
The power detector adc offset calibration has to be done on 4 minutes interval (longcal * pa_skip_count). But the commit "ath9k_hw: fix a noise floor calibration related race condition" makes the PA calibration executed more frequently beased on nfcal_pending value. Running PAOffset calibration lesser than longcal interval doesn't help anything and the worse part is that it causes NF load timeouts and RX deaf conditions. In a very noisy environment, where the distance b/w AP & station is ~10 meter and running a downlink udp traffic with frequent background scan causes "Timeout while waiting for nf to load: AR_PHY_AGC_CONTROL=0x40d1a" and moves the chip into deaf state. This issue was originaly reported in Android platform where the network-manager application does bgscan more frequently on AR9271 chips. (AR9285 family usb device). Cc: stable@kernel.org Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-17ath9k_htc: Fix endian issue in tx headerRajkumar Manoharan
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-17ath9k_hw: ASPM interoperability fix for AR9380/AR9382Luis R. Rodriguez
There is an interoperability with AR9382/AR9380 in L1 state with a few root complexes which can cause a hang. This is fixed by setting some work around bits on the PCIE PHY. We fix by using a new ini array to modify these bits when the radio is idle. Cc: stable@kernel.org Cc: Jack Lee <jack.lee@atheros.com> Cc: Carl Huang <carl.huang@atheros.com> Cc: David Quan <david.quan@atheros.com> Cc: Nael Atallah <nael.atallah@atheros.com> Cc: Sarvesh Shrivastava <sarvesh.shrivastava@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-13rt2x00: Don't leak mem in error path of rt2x00lib_request_firmware()Jesper Juhl
We need to release_firmware() in order not to leak memory. Signed-off-by: Jesper Juhl <jj@chaosbits.net> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Acked-by: Pekka Enberg <penberg@kernel.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-13iwmc3200wifi: Return proper error for iwm_if_allocAxel Lin
In the case of alloc_netdev_mq failure and kmalloc failure, current implementation returns ERR_PTR(0). As a result, the caller of iwm_if_alloc does not catch the error by IS_ERR macro. Fix it by setting proper error code for ret variable in the failure cases. Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-10hostap_cs: fix sleeping function called from invalid contextStanislaw Gruszka
pcmcia_request_irq() and pcmcia_enable_device() are intended to be called from process context (first function allocate memory with GFP_KERNEL, second take a mutex). We can not take spin lock and call them. It's safe to move spin lock after pcmcia_enable_device() as we still hold off IRQ until dev->base_addr is 0 and driver will not proceed with interrupts when is not ready. Patch resolves: https://bugzilla.redhat.com/show_bug.cgi?id=643758 Reported-and-tested-by: rbugz@biobind.com Cc: stable@kernel.org # 2.6.34+ Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-10ipw2200: Check for -1 INTA in tasklet too.Indan Zupancic
This is an attempt to fix a long standing open bug: http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=1334 The interrupt handler checks for INTA being -1, apparently that means that the hardware is gone. But the interrupt handler defers actual interrupt processing to a tasklet. By the time the tasklet is run and checks INTA again, the hardware might be gone and INTA be -1, which confuses the driver because all event bits are set. The patch applies to 2.6.37. Signed-off-by: Indan Zupancic <indan@nul.nu> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-10p54: fix sequence no. accounting off-by-one errorChristian Lamparter
P54_HDR_FLAG_DATA_OUT_SEQNR is meant to tell the firmware that "the frame's sequence number has already been set by the application." Whereas IEEE80211_TX_CTL_ASSIGN_SEQ is set for frames which lack a valid sequence number and either the driver or firmware has to assign one. Yup, it's the exact opposite! Cc: <stable@kernel.org> Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-10ath9k_htc: Really fix packet injectionSujith Manoharan
The chainmask value along with other configuration has to be set on the target for packet injection. Fix this and also move the monitor interface addition before the channel set segment to ensure that the opmode is updated properly. Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-10ath9k_hw: Fix RX handling for USB devicesSujith Manoharan
Commit "ath9k_hw: Abort rx if hw is not coming out of full sleep in reset" uncondionally added aborting RX DMA in a HW reset, though it is a bit unclear as to why this is needed. Anyway, RX DMA is handled in the target for USB devices, and this would interfere with normal operations (scanning etc.), so fix this. Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-10ath9k_hw: Fix thermal issue with UB94Sujith Manoharan
Hardcode the output voltage of x-PA bias LDO to the lowest value for UB94. The card doesn't get too hot now. Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-10ath9k_hw: Fix calibration for AR9287 devicesSujith Manoharan
AR9287 based devices have issues with ADC gain calibration which would cause uplink throughput drops in HT40 mode. Remove ADC gain from the supported calibration algorithms. Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-10ath9k_hw: Fix chip testSujith Manoharan
USB devices do not require the chip test routine. Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-07Merge branch 'for-2.6.38' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wqLinus Torvalds
* 'for-2.6.38' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (33 commits) usb: don't use flush_scheduled_work() speedtch: don't abuse struct delayed_work media/video: don't use flush_scheduled_work() media/video: explicitly flush request_module work ioc4: use static work_struct for ioc4_load_modules() init: don't call flush_scheduled_work() from do_initcalls() s390: don't use flush_scheduled_work() rtc: don't use flush_scheduled_work() mmc: update workqueue usages mfd: update workqueue usages dvb: don't use flush_scheduled_work() leds-wm8350: don't use flush_scheduled_work() mISDN: don't use flush_scheduled_work() macintosh/ams: don't use flush_scheduled_work() vmwgfx: don't use flush_scheduled_work() tpm: don't use flush_scheduled_work() sonypi: don't use flush_scheduled_work() hvsi: don't use flush_scheduled_work() xen: don't use flush_scheduled_work() gdrom: don't use flush_scheduled_work() ... Fixed up trivial conflict in drivers/media/video/bt8xx/bttv-input.c as per Tejun.
2011-01-05Merge branch 'master' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6 into for-davem Conflicts: net/bluetooth/Makefile
2011-01-05ath9k: correct MODULE_PARM_DESC parameters for force_new_aniJohn W. Linville
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-05ath5k: qualify global modparam_nohwcrypt variableJohn W. Linville
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-05ath9k: qualify global modparam_nohwcrypt variableJohn W. Linville
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-05Merge branch 'master' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
2011-01-04libertas: down_interruptible() can return -EINTR, not EINTRroel kluin
Fix test in lbs_spi_thread(). down_interruptible() can return -EINTR, but not EINTR. Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Cc: Dan Williams <dcbw@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-04ath9k_htc: Fix packet injectionSujith Manoharan
To inject a packet in monitor mode, a dummy station has to be associated with the monitor interface in the target. Failing to do this would result in a firmware crash on the device. Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-04ath5k: ath5k_eeprom_mode_from_channel() returns signedDan Carpenter
ath5k_eeprom_mode_from_channel() returns -1 on error but we're storing the result in "ee_mode" which is an unsigned char. This breaks the error handling. This patch makes "ee_mode" an int. Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-04ath9k : few rate control clean upsMohammed Shafi Shajakhan
Remove some obvious looking dead code and rename few functions Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-04ath9k: fix beacon restart on channel changeRajkumar Manoharan
Restart the beacon timers only if the beacon was already configured. Otherwise beacons timers are restarted unnecessarily in unassociated state too. Cc: stable@kernel.org Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-04Revert "ath9k: Parse DTIM period from mac80211"Mohammed Shafi Shajakhan
This reverts commit 0ce3bcfc84900a64347b0fe1140229bd81314008. Event though with the above commit we obtain the configured DTIM period from the AP rather than always hardcoding it to '1', this seems to cause problems under the following scenarios: * Preventing association with broken AP's * Adds latency in roaming So its better to always use the safe value of '1' for dtim period Cc: Jouni Malinen <Jouni.Malinen@Atheros.com> Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-04ath9k_hw: fix dma descriptor rx error bit parsingFelix Fietkau
An Rx DMA descriptor can have multiple error bits set, and some error bits (e.g. MIC failure) are filtered by the driver based on other criteria. Remove the 'else' in various error bit checks so that all error information is properly passed to the driver. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-04ath9k_htc: Move LED/RFKILL code to htc_drv_gpio.cSujith Manoharan
And add the copyright/license header. Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-04ath9k_htc: Fix fast channel changeSujith Manoharan
When returning to the operating channel, a full HW reset has to be done instead of a fast channel change. Since sw_scan_complete() is called after the config() call for the home channel, we end up doing a FCC. Fix this issue by checking the OFFCHANNEL flag to determine FCC. Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-04ath9k_htc: Handle FATAL eventsSujith Manoharan
The device has to be reset when a FATAL event is received. Not doing so would leave the card in a non-working state. Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-04ath9k_htc: Move work cancellation outside of mutexSujith Manoharan
There is no need to lock the various work cancellation calls. This will be helpful when handling FATAL events. Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-04ath9k_htc: Handle pending URBs properlySujith Manoharan
When doing a channel change, the pending URBs have to be killed properly on calling htc_stop(). This fixes the probe response timeout seen when sending UDP traffic at a high rate and running background scan at the same time. Cc: stable <stable@kernel.org> Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-04ath9k: Few clean ups in beacon config parametersMohammed Shafi Shajakhan
Some minor clean ups in assigning values to beacon config parameters Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-04rt2x00: Fix comment about removed spinlockHelmut Schaa
The comment doesn't match the code anymore. Fix that. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-04rt2x00: Remove unused interface spinlockHelmut Schaa
Since the last user of intf->lock is gone we can safely remove it. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-04rt2x00: Simplify intf->delayed_flags lockingHelmut Schaa
Instead of protecting delayed_flags with a spinlock use atomic bitops to make the code more readable. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-04rt2x00: Remove superfluous assignment of mpdu_densityHelmut Schaa
The tx desciptor already gets initialized to 0. Hence, there's no need to explicitly assign 0 to mpdu_density here. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-04rt2x00: Fix panic on frame padding for rt2800 usb devicesIsmael Luceno
Backtrace: rt2800usb_write_tx_data rt2x00queue_write_tx_frame rt2x00mac_tx invoke_tx_handlers __ieee80211_tx ieee80211_tx virt_to_head_page ieee80211_xmit ieee80211_tx_skb ieee80211_scan_work schedule ieee80211_scan_work process_one_work ... It tried to expand the skb past it's end using skb_put. So I replaced it with a call to skb_padto, which takes the issue into account. Signed-off-by: Ismael Luceno <ismael.luceno@gmail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-04rt2x00: Fix pointer errors.Gertjan van Wingerde
Fix some pointer errors in the various calls to memcpy, memset and memmove. Although none of these errors are fatal (the expression used now results in the same pointer value) it is better to use the proper expression. All errors are having to deal with arrays. Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-04rt2x00: remove intf->mac field.Gertjan van Wingerde
The mac field of the rt2x00_intf structure is written to once and used twice. In both these uses the mac address is available via other means. Remove this field as it does not appear to be necessary. Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-04rt2x00: Remove intf->bssid field.Gertjan van Wingerde
The bssid field in struct rt2x00_intf is only written to once, and is never read from. Remove this field, as it appears to not be needed. Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-04rt2x00: allow txstatus_fifo w/o txstatus_taskletJohannes Stezenbach
When DRIVER_REQUIRE_TXSTATUS_FIFO is set, intialize the txstatus_fifo, but initialize rt2x00dev->txstatus_tasklet only when both DRIVER_REQUIRE_TXSTATUS_FIFO and rt2x00dev->ops->lib->txstatus_tasklet are set. This allows the txstatus_fifo to be used by rt2800usb which does not use txstatus_tasklet. Signed-off-by: Johannes Stezenbach <js@sig21.net> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-04rt2x00: simplify txstatus_fifo handlingJohannes Stezenbach
Signed-off-by: Johannes Stezenbach <js@sig21.net> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-04carl9170: fix usb pm suspend->resume woesChristian Lamparter
This patch revamps some common code-paths which are shared between (re-)initialization and suspend/resume subroutines. It also adds some helpful comments about quirks and associated difficulties. It's quite big, but it should fix #25382: <https://bugzilla.kernel.org/show_bug.cgi?id=25382> And hopefully the code is robust enough to deal with all possible suspend/resume scenarios without requiring the user to do any sort of manual and possibly dangerous work. Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-04carl9170: reduce channel change delayChristian Lamparter
By removing two "safety" msleeps (and an echo nop), the channel change delay is effectively halved. Previously, the delay could be as long as 260 ms and the device could not go off-channel without risking to miss the next DTIM beacon [interval ~307 ms]. Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-04carl9170: add missing return-value checkChristian Lamparter
This patch adds a forgotten bail-out path. Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-04ath5k: fix cycle counter inconsistent lockingBob Copeland
ath5k_reset is called from process context and takes the cc_lock with plain spin_lock(), but cc_lock can also be taken from tasklets in softirq context. Thus we need to at least use spin_lock_bh. This fixes the following lockdep warning: [ 19.967874] sky2 0000:01:00.0: eth0: enabling interface [ 19.982761] ieee80211 phy0: device now idle [ 20.904809] NET: Registered protocol family 17 [ 21.243857] ieee80211 phy0: device no longer idle - scanning [ 21.404343] [ 21.404346] ================================= [ 21.404450] [ INFO: inconsistent lock state ] [ 21.404518] 2.6.37-rc7-wl+ #242 [ 21.404582] --------------------------------- [ 21.404650] inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage. [ 21.404721] kworker/u:4/982 [HC0[0]:SC1[3]:HE1:SE0] takes: [ 21.404792] (&(&common->cc_lock)->rlock){+.?...}, at: [<f8115780>] ath5k_ani_calibration+0x29/0x5d9 [ath5k] [ 21.405011] {SOFTIRQ-ON-W} state was registered at: [ 21.405011] [<c105cadd>] __lock_acquire+0x62f/0x13c1 [ 21.405011] [<c105d944>] lock_acquire+0xd5/0xf1 [ 21.405011] [<c12c978d>] _raw_spin_lock+0x45/0x72 [ 21.405011] [<f8111533>] ath5k_reset+0x2c0/0x349 [ath5k] [ 21.405011] [<f8111a7a>] ath5k_start+0xb8/0x139 [ath5k] [ 21.405011] [<f849c714>] ieee80211_do_open+0x13f/0x819 [mac80211] [ 21.405011] [<f849ce51>] ieee80211_open+0x63/0x66 [mac80211] [ 21.405011] [<c1258b2e>] __dev_open+0x8d/0xb6 [ 21.405011] [<c1255c64>] __dev_change_flags+0x9d/0x114 [ 21.405011] [<c1258a75>] dev_change_flags+0x18/0x44 [ 21.405011] [<c1262990>] do_setlink+0x23f/0x521 [ 21.405011] [<c1262d58>] rtnl_setlink+0xe6/0xea [ 21.405011] [<c126347c>] rtnetlink_rcv_msg+0x18a/0x1a0 [ 21.405011] [<c126d5f0>] netlink_rcv_skb+0x35/0x7b [ 21.405011] [<c12632eb>] rtnetlink_rcv+0x20/0x27 [ 21.405011] [<c126d370>] netlink_unicast+0x1bb/0x21e [ 21.405011] [<c126db21>] netlink_sendmsg+0x23b/0x288 [ 21.405011] [<c124823c>] sock_sendmsg+0xac/0xc4 [ 21.405011] [<c1248680>] sys_sendmsg+0x152/0x1a2 [ 21.405011] [<c1249b0d>] sys_socketcall+0x214/0x275 [ 21.405011] [<c10029d0>] sysenter_do_call+0x12/0x36 [ 21.405011] irq event stamp: 138032 [ 21.405011] hardirqs last enabled at (138032): [<c12ca252>] _raw_spin_unlock_irqrestore+0x3b/0x5e [ 21.405011] hardirqs last disabled at (138031): [<c12c98cc>] _raw_spin_lock_irqsave+0x18/0x7e [ 21.405011] softirqs last enabled at (138024): [<f84a570e>] ieee80211_tx_skb+0x47/0x49 [mac80211] [ 21.405011] softirqs last disabled at (138027): [<c100452b>] do_softirq+0x63/0xb4 [ 21.405011] [ 21.405011] other info that might help us debug this: [ 21.405011] 3 locks held by kworker/u:4/982: [ 21.405011] #0: (name){+.+.+.}, at: [<c1046158>] process_one_work+0x1b8/0x41b [ 21.405011] #1: ((&(&local->scan_work)->work)){+.+.+.}, at: [<c1046158>] process_one_work+0x1b8/0x41b [ 21.405011] #2: (&local->mtx){+.+.+.}, at: [<f84920fb>] ieee80211_scan_work+0x32/0x4a4 [mac80211] [ 21.405011] [ 21.405011] stack backtrace: [ 21.405011] Pid: 982, comm: kworker/u:4 Not tainted 2.6.37-rc7-wl+ #242 [ 21.405011] Call Trace: [ 21.405011] [<c12c6e68>] ? printk+0x1d/0x25 [ 21.405011] [<c105a742>] print_usage_bug+0x181/0x18b [ 21.405011] [<c105b196>] ? check_usage_forwards+0x0/0xb6 [ 21.405011] [<c105a9ec>] mark_lock+0x2a0/0x4aa [ 21.405011] [<c1059f6d>] ? trace_hardirqs_off+0xb/0xd [ 21.405011] [<c105ca68>] __lock_acquire+0x5ba/0x13c1 [ 21.405011] [<c1059eed>] ? trace_hardirqs_off_caller+0x18/0x8d [ 21.405011] [<c1059f6d>] ? trace_hardirqs_off+0xb/0xd [ 21.405011] [<c1050411>] ? local_clock+0x2c/0x4f [ 21.405011] [<c1059e00>] ? save_trace+0x2/0xa0 [ 21.405011] [<c105ac39>] ? mark_held_locks+0x43/0x5b [ 21.405011] [<c12ca252>] ? _raw_spin_unlock_irqrestore+0x3b/0x5e [ 21.405011] [<f8115780>] ? ath5k_ani_calibration+0x29/0x5d9 [ath5k] [ 21.405011] [<c105d944>] lock_acquire+0xd5/0xf1 [ 21.405011] [<f8115780>] ? ath5k_ani_calibration+0x29/0x5d9 [ath5k] [ 21.405011] [<c12c9b1a>] _raw_spin_lock_bh+0x4a/0x77 [ 21.405011] [<f8115780>] ? ath5k_ani_calibration+0x29/0x5d9 [ath5k] [ 21.405011] [<f8115780>] ath5k_ani_calibration+0x29/0x5d9 [ath5k] [ 21.405011] [<c105ac39>] ? mark_held_locks+0x43/0x5b [ 21.405011] [<f8113496>] ath5k_tasklet_ani+0x1d/0x27 [ath5k] [ 21.405011] [<c1037304>] tasklet_action+0x96/0x137 [ 21.405011] [<c10379b5>] __do_softirq+0xde/0x1c3 [ 21.405011] [<c10b0cef>] ? arch_get_unmapped_area_topdown+0x3b/0x127 [ 21.405011] [<c10378d7>] ? __do_softirq+0x0/0x1c3 [ 21.405011] <IRQ> [<c1036dee>] ? irq_exit+0x3d/0x49 [ 21.405011] [<c1003b4f>] ? do_IRQ+0x98/0xac [ 21.405011] [<c1002eee>] ? common_interrupt+0x2e/0x34 [ 21.405011] [<c103007b>] ? sys_unshare+0x57/0x226 [ 21.405011] [<c1047fee>] ? queue_delayed_work+0x1/0x27 [ 21.405011] [<f84a83a0>] ? ieee80211_queue_delayed_work+0x2e/0x33 [mac80211] [ 21.405011] [<f8492528>] ? ieee80211_scan_work+0x45f/0x4a4 [mac80211] [ 21.405011] [<c104620e>] ? process_one_work+0x26e/0x41b [ 21.405011] [<c1046158>] ? process_one_work+0x1b8/0x41b [ 21.405011] [<f84920c9>] ? ieee80211_scan_work+0x0/0x4a4 [mac80211] [ 21.405011] [<c10466b6>] ? worker_thread+0x18a/0x2a5 [ 21.405011] [<c12ca25e>] ? _raw_spin_unlock_irqrestore+0x47/0x5e [ 21.405011] [<c104652c>] ? worker_thread+0x0/0x2a5 [ 21.405011] [<c104abe7>] ? kthread+0x67/0x6c [ 21.405011] [<c104ab80>] ? kthread+0x0/0x6c [ 21.405011] [<c1002efa>] ? kernel_thread_helper+0x6/0x10 Signed-off-by: Bob Copeland <me@bobcopeland.com> Acked-by: Bruno Randolf <br1@einfach.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-04ath9k: fix spur mitigation no-spur case for AR9002Brian Prodoehl
For the AR9002, the spur frequency read from the EEPROM is mangled before being compared against AR_NO_SPUR. This results in the driver trying to set up the spur mitigation for bogus spurs, rather than cleanly breaking out. Signed-off-by: Brian Prodoehl <bprodoehl@nomadio.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-04airo: use simple_write_to_bufferAkinobu Mita
Simplify write file operation for /proc files by using simple_write_to_buffer(). Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Cc: "John W. Linville" <linville@tuxdriver.com> Cc: linux-wireless@vger.kernel.org Cc: netdev@vger.kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
generated by cgit v1.2.3-18-g5258 (git 2.32.0) at 2024-12-30 05:12:43 +0000