| Age | Commit message (Collapse) | Author |
|---|
|
commit 83e612f632c3897be29ef02e0472f6d63e258378 upstream.
Both type and pkt_len variables are in host endian and these should be in
Little Endian in the payload.
Signed-off-by: Tomasz Moń <desowin@gmail.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e2288b66fe7ff0288382b2af671b4da558b44472 upstream.
Since we clear QUEUE_STARTED in rt2x00queue_stop_queue(), following
call to rt2x00queue_pause_queue() reduce to noop, i.e we do not
stop queue in mac80211.
To fix that introduce rt2x00queue_pause_queue_nocheck() function,
which will stop queue in mac80211 directly.
Note that rt2x00_start_queue() explicitly set QUEUE_PAUSED bit.
Note also that reordering operations i.e. first call to
rt2x00queue_pause_queue() and then clear QUEUE_STARTED bit, will race
with rt2x00queue_unpause_queue(), so calling ieee80211_stop_queue()
directly is the only available solution to fix the problem without
major rework.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dc2a87f519a4d8cb376ab54f22b6b98a943b51ce upstream.
Currently we configure harwdare and clock, only after
interface start. In this case, if we reload module or
reboot PC without configuring adapter, firmware will freeze.
There is no software way to reset adpter.
This patch add initial configuration and set it in
disabled state, to avoid this freeze. Behaviour of this patch
should be similar to: ifconfig wlan0 up; ifconfig wlan0 down.
Bug: https://github.com/qca/open-ath9k-htc-firmware/issues/1
Tested-by: Bo Shi <cnshibo@gmail.com>
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0a6f3a8ebaf13407523c2c7d575b4ca2debd23ba upstream.
The current code uses the same index value both
for the channel information array and for the TX
power table. The index starts from 14, however the
index of the TX power table must start from zero.
Fix it, in order to get the correct TX power value
for a given channel.
The changes in rt61pci.c and rt73usb.c are compile
tested only.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 531671cb17af07281e6f28c1425f754346e65c41 upstream.
Almost all the DMA issues which have plagued ath9k (in station mode)
for years are related to PS. Disabling PS usually "fixes" the user's
connection stablility. Reports of DMA problems are still trickling in
and are sitting in the kernel bugzilla. Until the PS code in ath9k is
given a thorough review, disbale it by default. The slight increase
in chip power consumption is a small price to pay for improved link
stability.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e0e29b683d6784ef59bbc914eac85a04b650e63c upstream.
The module parameter "fwpostfix" is userspace controllable, unfiltered,
and is used to define the firmware filename. b43_do_request_fw() populates
ctx->errors[] on error, containing the firmware filename. b43err()
parses its arguments as a format string. For systems with b43 hardware,
this could lead to a uid-0 to ring-0 escalation.
CVE-2013-2852
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ccd384b10420ac81ba3fb9b0a7d18272c7173552 upstream.
A small bug in this code was causing the ALLMULTI filter to be set
when in fact we were just wanting to program a selective multicast list
to the hardware.
Fix that bug and remove a redundant if condition in the code that
follows.
This fixes wakeup behaviour when multicast WOL is enabled. Previously,
all multicast packets would wake up the system. Now, only those that the
host intended to receive trigger wakeups.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 48795424acff7215d5eac0b52793a2c1eb3a6283 upstream.
When the XO-4 with 8787 wireless is woken up due to wake-on-WLAN
mwifiex is often flooded with "not allowed while suspended" messages
and the interface is unusable.
[ 202.171609] int: sdio_ireg = 0x1
[ 202.180700] info: mwifiex_process_hs_config: auto cancelling host
sleep since there is interrupt from the firmware
[ 202.201880] event: wakeup device...
[ 202.211452] event: hs_deactivated
[ 202.514638] info: --- Rx: Data packet ---
[ 202.514753] data: 4294957544 BSS(0-0): Data <= kernel
[ 202.514825] PREP_CMD: device in suspended state
[ 202.514839] data: dequeuing the packet ec7248c0 ec4869c0
[ 202.514886] mwifiex_write_data_sync: not allowed while suspended
[ 202.514886] host_to_card, write iomem (1) failed: -1
[ 202.514917] mwifiex_write_data_sync: not allowed while suspended
[ 202.514936] host_to_card, write iomem (2) failed: -1
[ 202.514949] mwifiex_write_data_sync: not allowed while suspended
[ 202.514965] host_to_card, write iomem (3) failed: -1
[ 202.514976] mwifiex_write_data_async failed: 0xFFFFFFFF
This can be readily reproduced when putting the XO-4 in a loop where
it goes to sleep due to inactivity, but then wakes up due to an
incoming ping. The error is hit within an hour or two.
This issue happens when an interrupt comes in early while host sleep
is still activated. Driver handles this case by auto cancelling host
sleep. However is_suspended flag is still set which prevents any cmd
or data from being sent to firmware. Fix it by clearing is_suspended
flag in this path.
Reported-by: Daniel Drake <dsd@laptop.org>
Tested-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4ef69d0394cba8caa9f75d3f2e53429bfb8b3045 upstream.
If no keycache slots are available, ath_key_config can return -ENOSPC.
If the key index is not checked for errors, it can lead to logspam that
looks like this: "ath: wiphy0: keyreset: keycache entry 228 out of range"
This can cause follow-up errors if the invalid keycache index gets
used for tx.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 319e7bd96aca64a478f3aad40711c928405b8b77 upstream.
Since the firmware has been open sourced, the minor version has been
bumped to 1.4 and the API/ABI will stay compatible across further 1.x
releases.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 83589b30f1e1dc9898986293c9336b8ce1705dec upstream.
BugLink: http://bugs.launchpad.net/bugs/1128840
It appears that when this register read fails it never recovers, so
I think there is no need to repeat the same error message ad infinitum.
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: linux-wireless@vger.kernel.org
Cc: users@rt2x00.serialmonkey.com
Cc: netdev@vger.kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
revert commit b9f1f48ce20a1b923429c216669d03b5a900a8cf which is commit
084c7189acb3f969c855536166042e27f5dd703f upstream.
It shouldn't have been applied to the 3.0-stable tree.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Cc: Marco Cesarano <marco@marvell.com>
Reported-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 084c7189acb3f969c855536166042e27f5dd703f upstream.
curr_cmd points to the command that is in processing or waiting
for its command response from firmware. If the function shutdown
happens to occur at this time we should cancel the cmd timer and
put the command back to free queue.
Tested-by: Marco Cesarano <marco@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b251412db99ccd4495ce372fec7daee27bf06923 upstream.
Intermittently, b43 will report "Out of order TX status report on DMA ring".
When this happens, the driver must be reset before communication can resume.
The cause of the problem is believed to be an error in the closed-source
firmware; however, all versions of the firmware are affected.
This change uses the observation that the expected status is always 2 less
than the observed value, and supplies a fake status report to skip one
header/data pair.
Not all devices suffer from this problem, but it can occur several times
per second under heavy load. As each occurence kills the unmodified driver,
this patch makes if possible for the affected devices to function. The patch
logs only the first instance of the reset operation to prevent spamming
the logs.
Tested-by: Chris Vine <chris@cvine.freeserve.co.uk>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6ef9e2f6d12ce9e2120916804d2ddd46b954a70b upstream.
If CONFIG_MAC80211_MESH is not set, cfg80211 will now allow advertising
interface combinations with NL80211_IFTYPE_MESH_POINT present.
Add appropriate ifdefs to avoid running into errors.
[Backported for 3.8-stable. Removed code of simultaneous AP and mesh
mode added in 4a5fc6d 3.9-rc1.]
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Lingzhu Xiang <lxiang@redhat.com>
Reviewed-by: CAI Qian <caiqian@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5f0fabf84d7b52f979dcbafa3d3c530c60d9a92c upstream.
smatch found this error:
CHECK drivers/net/wireless/mwifiex/join.c
drivers/net/wireless/mwifiex/join.c:1121
mwifiex_cmd_802_11_ad_hoc_join()
error: testing array offset 'i' after use.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a3d63cadbad97671d740a9698acc2c95d1ca6e79 upstream.
RSSI is being stored internally as s8 in several places. The indication
of an unset RSSI value, ATH_RSSI_DUMMY_MARKER, was supposed to have been
set to 127, but ended up being set to 0x127 because of a code cleanup
mistake. This could lead to invalid signal strength values in a few
places.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 008e33f733ca51acb2dd9d88ea878693b04d1d2a upstream.
Corrected USB ID for T-Com Sinus 154 data II. ISL3887-based. The
device was tested in managed mode with no security, WEP 128
bit and WPA-PSK (TKIP) with firmware 2.13.1.0.lm87.arm (md5sum:
7d676323ac60d6e1a3b6d61e8c528248). It works.
Signed-off-by: Tomasz Guszkowski <tsg@o2.pl>
Acked-By: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0a06ad8e3a1cb5311b7dbafde45410aa1bce9d40 upstream.
In routine _rtl_rx_pre_process(), skb_dequeue() is called to get an skb;
however, the wrong variable name is used in subsequent calls.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1adb2e2b5f85023d17eb4f95386a57029df27c88 upstream.
When the next beacon is sent, the ath_buf from the previous run is reused.
If getting a new beacon from mac80211 fails, bf->bf_mpdu is not reset, yet
the skb is freed, leading to a double-free on the next beacon tx attempt,
resulting in a system crash.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0981c3b24ef664f5611008a6e6d0622fac6d892b upstream.
SKBs that are allocated in the HTC layer do not have callbacks
registered and hence ended up not being freed, Fix this by freeing
them properly in the TX completion routine.
Reported-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b3cd8021379306c0be6932e4d3b4b01efc681769 upstream.
Trying to access the OTP memory on the AR9340
causes a data bus error like this:
Data bus error, epc == 86e84164, ra == 86e84164
Oops[#1]:
Cpu 0
$ 0 : 00000000 00000061 deadc0de 00000000
$ 4 : b8115f18 00015f18 00000007 00000004
$ 8 : 00000001 7c7c3c7c 7c7c7c7c 7c7c7c7c
$12 : 7c7c3c7c 001f0041 00000000 7c7c7c3c
$16 : 86ee0000 00015f18 00000000 00000007
$20 : 00000004 00000064 00000004 86d71c44
$24 : 00000000 86e6ca00
$28 : 86d70000 86d71b20 86ece0c0 86e84164
Hi : 00000000
Lo : 00000064
epc : 86e84164 ath9k_hw_wait+0x58/0xb0 [ath9k_hw]
Tainted: G O
ra : 86e84164 ath9k_hw_wait+0x58/0xb0 [ath9k_hw]
Status: 1100d403 KERNEL EXL IE
Cause : 4080801c
PrId : 0001974c (MIPS 74Kc)
Modules linked in: ath9k(O+) ath9k_common(O) ath9k_hw(O) ath(O) ar934x_nfc
mac80211(O) usbcore usb_common scsi_mod nls_base nand nand_ecc nand_ids
crc_ccitt cfg80211(O) compat(O) arc4 aes_generic crypto_blkcipher cryptomgr
aead crypto_hash crypto_algapi ledtrig_timer ledtrig_default_on leds_gpio
Process insmod (pid: 459, threadinfo=86d70000, task=87942140, tls=779ac440)
Stack : 802fb500 000200da 804db150 804e0000 87816130 86ee0000 00010000 86d71b88
86d71bc0 00000004 00000003 86e9fcd0 80305300 0002c0d0 86e74c50 800b4c20
000003e8 00000001 00000000 86ee0000 000003ff 86e9fd64 80305300 80123938
fffffffc 00000004 000058bc 00000000 86ea0000 86ee0000 000001ff 878d6000
99999999 86e9fdc0 86ee0fcc 86e9e664 0000c0d0 86ee0000 0000700000007000
...
Call Trace:
[<86e84164>] ath9k_hw_wait+0x58/0xb0 [ath9k_hw]
[<86e9fcd0>] ath9k_hw_setup_statusring+0x16b8/0x1c7c [ath9k_hw]
Code: 0000a812 0040f809 00000000 <00531024> 1054000b 24020001 0c05b5dc 2404000a 26520001
The cause of the error is that the OTP register
offsets are different on the AR9340 than the
actually used values.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9c170e068636deb3e3f96114034bb711675f0faa upstream.
This reverts commit f74b9d365ddd33a375802b064f96a5d0e99af7c0.
Turns out reverting commit a240dc7b3c7463bd60cf0a9b2a90f52f78aae0fd
"ath9k_hw: Updated AR9003 tx gain table for 5GHz" was not enough to
bring the tx power back to normal levels on devices like the
Buffalo WZR-HP-G450H, this one needs to be reverted as well.
This revert improves tx power by ~10 db on that device
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: rmanohar@qca.qualcomm.com
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4010fe21a315b4223c25376714c6a2b61b722e5c upstream.
This patch adds USBIDs for:
- DrayTek Vigor 530
- Zoom 4410a
It also adds a note about Gemtek WUBI-100GW
and SparkLAN WL-682 USBID conflict [WUBI-100GW
is a ISL3886+NET2280 (LM86 firmare) solution,
whereas WL-682 is a ISL3887 (LM87 firmware)]
device.
Source: <http://www.wikidevi.com/wiki/Intersil/p54/usb/windows>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3194b7fcdf6caea338b5d2c72d76fed80437649c upstream.
Added USB ID for T-Com Sinus 154 data II.
Signed-off-by: Tomasz Guszkowski <tsg@o2.pl>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dd321acddc3be1371263b8c9e6c6f2af89f63d57 upstream.
When host_sleep_config command fails we should return error to
MMC core to indicate the failure for our device.
The misspelled variable is also removed as it's redundant.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a485e827f07bfdd0762059386e6e787bed6e81ee upstream.
This is an ISY IWL 2000. Probably a clone of Belkin F7D1102 050d:1102.
Its FCC ID is the same.
Signed-off-by: Albert Pool <albertpool@solcon.nl>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bf7e1abe434ba9e22e8dc04a4cba4ab504b788b8 upstream.
Some hardware has correct (!= 0xff) value of tssi_bounds[4] in the
EEPROM, but step is equal to 0xff. This results on ridiculous delta
calculations and completely broke TX power settings.
Reported-and-tested-by: Pavel Lucik <pavel.lucik@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8c6e30936a7893a85f6222084f0f26aceb81137a upstream.
bf->bf_next is only while buffers are chained as part of an A-MPDU
in the tx queue. When a tid queue is flushed (e.g. on tearing down
an aggregation session), frames can be enqueued again as normal
transmission, without bf_next being cleared. This can lead to the
old pointer being dereferenced again later.
This patch might fix crashes and "Failed to stop TX DMA!" messages.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2d838bb608e2d1f6cb4280e76748cb812dc822e7 upstream.
When b43legacy is loaded without the firmware being available, a following
unload generates a kernel NULL pointer dereference BUG as follows:
[ 214.330789] BUG: unable to handle kernel NULL pointer dereference at 0000004c
[ 214.330997] IP: [<c104c395>] drain_workqueue+0x15/0x170
[ 214.331179] *pde = 00000000
[ 214.331311] Oops: 0000 [#1] SMP
[ 214.331471] Modules linked in: b43legacy(-) ssb pcmcia mac80211 cfg80211 af_packet mperf arc4 ppdev sr_mod cdrom sg shpchp yenta_socket pcmcia_rsrc pci_hotplug pcmcia_core battery parport_pc parport floppy container ac button edd autofs4 ohci_hcd ehci_hcd usbcore usb_common thermal processor scsi_dh_rdac scsi_dh_hp_sw scsi_dh_emc scsi_dh_alua scsi_dh fan thermal_sys hwmon ata_generic pata_ali libata [last unloaded: cfg80211]
[ 214.333421] Pid: 3639, comm: modprobe Not tainted 3.6.0-rc6-wl+ #163 Source Technology VIC 9921/ALI Based Notebook
[ 214.333580] EIP: 0060:[<c104c395>] EFLAGS: 00010246 CPU: 0
[ 214.333687] EIP is at drain_workqueue+0x15/0x170
[ 214.333788] EAX: c162ac40 EBX: cdfb8360 ECX: 0000002a EDX: 00002a2a
[ 214.333890] ESI: 00000000 EDI: 00000000 EBP: cd767e7c ESP: cd767e5c
[ 214.333957] DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
[ 214.333957] CR0: 8005003b CR2: 0000004c CR3: 0c96a000 CR4: 00000090
[ 214.333957] DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
[ 214.333957] DR6: ffff0ff0 DR7: 00000400
[ 214.333957] Process modprobe (pid: 3639, ti=cd766000 task=cf802e90 task.ti=cd766000)
[ 214.333957] Stack:
[ 214.333957] 00000292 cd767e74 c12c5e09 00000296 00000296 cdfb8360 cdfb9220 00000000
[ 214.333957] cd767e90 c104c4fd cdfb8360 cdfb9220 cd682800 cd767ea4 d0c10184 cd682800
[ 214.333957] cd767ea4 cba31064 cd767eb8 d0867908 cba31064 d087e09c cd96f034 cd767ec4
[ 214.333957] Call Trace:
[ 214.333957] [<c12c5e09>] ? skb_dequeue+0x49/0x60
[ 214.333957] [<c104c4fd>] destroy_workqueue+0xd/0x150
[ 214.333957] [<d0c10184>] ieee80211_unregister_hw+0xc4/0x100 [mac80211]
[ 214.333957] [<d0867908>] b43legacy_remove+0x78/0x80 [b43legacy]
[ 214.333957] [<d083654d>] ssb_device_remove+0x1d/0x30 [ssb]
[ 214.333957] [<c126f15a>] __device_release_driver+0x5a/0xb0
[ 214.333957] [<c126fb07>] driver_detach+0x87/0x90
[ 214.333957] [<c126ef4c>] bus_remove_driver+0x6c/0xe0
[ 214.333957] [<c1270120>] driver_unregister+0x40/0x70
[ 214.333957] [<d083686b>] ssb_driver_unregister+0xb/0x10 [ssb]
[ 214.333957] [<d087c488>] b43legacy_exit+0xd/0xf [b43legacy]
[ 214.333957] [<c1089dde>] sys_delete_module+0x14e/0x2b0
[ 214.333957] [<c110a4a7>] ? vfs_write+0xf7/0x150
[ 214.333957] [<c1240050>] ? tty_write_lock+0x50/0x50
[ 214.333957] [<c110a6f8>] ? sys_write+0x38/0x70
[ 214.333957] [<c1397c55>] syscall_call+0x7/0xb
[ 214.333957] Code: bc 27 00 00 00 00 a1 74 61 56 c1 55 89 e5 e8 a3 fc ff ff 5d c3 90 55 89 e5 57 56 89 c6 53 b8 40 ac 62 c1 83 ec 14 e8 bb b7 34 00 <8b> 46 4c 8d 50 01 85 c0 89 56 4c 75 03 83 0e 40 80 05 40 ac 62
[ 214.333957] EIP: [<c104c395>] drain_workqueue+0x15/0x170 SS:ESP 0068:cd767e5c
[ 214.333957] CR2: 000000000000004c
[ 214.341110] ---[ end trace c7e90ec026d875a6 ]---Index: wireless-testing/drivers/net/wireless/b43legacy/main.c
The problem is fixed by making certain that the ucode pointer is not NULL
before deregistering the driver in mac80211.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a396e10019eaf3809b0219c966865aaafec12630 upstream.
We need to program the rfkill switch GPIO pin direction to input at
device initialization time, not only when the interface is brought up.
Doing this only when the interface is brought up could lead to rfkill
detecting the switch is turned on erroneously and inability to create
the interface and bringing it up.
Reported-and-tested-by: Andreas Messer <andi@bastelmap.de>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo Van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6ced58a5dbb94dbfbea1b33ca3c56d1e929cd548 upstream.
The register is 16 bits wide, not 32.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo Van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a3433179d0822ccfa8e80aa4d1d52843bd2dcc63 upstream.
This structure needs to always stick around, even if CONFIG_HOTPLUG
is disabled, otherwise we can oops when trying to probe a device that
was added after the structure is thrown away.
Thanks to Fengguang Wu and Bjørn Mork for tracking this issue down.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reported-by: Bjørn Mork <bjorn@mork.no>
CC: Herton Ronaldo Krzesinski <herton@canonical.com>
CC: Hin-Tak Leung <htl10@users.sourceforge.net>
CC: Larry Finger <Larry.Finger@lwfinger.net>
CC: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b9c4167cbbafddac3462134013bc15e63e4c53ef upstream.
This structure needs to always stick around, even if CONFIG_HOTPLUG
is disabled, otherwise we can oops when trying to probe a device that
was added after the structure is thrown away.
Thanks to Fengguang Wu and Bjørn Mork for tracking this issue down.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reported-by: Bjørn Mork <bjorn@mork.no>
CC: Christian Lamparter <chunkeey@googlemail.com>
CC: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e1352fde5682ab1bdd2a9e5d75c22d1fe210ef77 upstream.
ath_rx_tasklet() calls ath9k_rx_skb_preprocess() and ath9k_rx_skb_postprocess()
in a loop over the received frames. The decrypt_error flag is
initialized to false
just outside ath_rx_tasklet() loop. ath9k_rx_accept(), called by
ath9k_rx_skb_preprocess(),
only sets decrypt_error to true and never to false.
Then ath_rx_tasklet() calls ath9k_rx_skb_postprocess() and passes
decrypt_error to it.
So, after a decryption error, in ath9k_rx_skb_postprocess(), we can
have a leftover value
from another processed frame. In that case, the frame will not be marked with
RX_FLAG_DECRYPTED even if it is decrypted correctly.
When using CCMP encryption this issue can lead to connection stuck
because of CCMP
PN corruption and a waste of CPU time since mac80211 tries to decrypt an already
deciphered frame with ieee80211_aes_ccm_decrypt.
Fix the issue initializing decrypt_error flag at the begging of the
ath_rx_tasklet() loop.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a769f9577232afe2c754606a83aad85127e7052a upstream.
This is a RT3070 based device.
Signed-off-by: Jeongdo Son <sohn9086@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit deee0214def5d8a32b8112f11d9c2b1696e9c0cb upstream.
We can not pass NULL libconf->conf->channel to rt61pci_config() as it
is dereferenced unconditionally in rt61pci_config_lna_gain() subroutine.
Resolves:
https://bugzilla.kernel.org/show_bug.cgi?id=44361
Reported-and-tested-by: <dolohow@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit efd821182cec8c92babef6e00a95066d3252fda4 upstream.
On rt2x00_dmastart() we increase index specified by Q_INDEX and on
rt2x00_dmadone() we increase index specified by Q_INDEX_DONE. So entries
between Q_INDEX_DONE and Q_INDEX are those we currently process in the
hardware. Entries between Q_INDEX and Q_INDEX_DONE are those we can
submit to the hardware.
According to that fix rt2x00usb_kick_queue(), as we need to submit RX
entries that are not processed by the hardware. It worked before only
for empty queue, otherwise was broken.
Note that for TX queues indexes ordering are ok. We need to kick entries
that have filled skb, but was not submitted to the hardware, i.e.
started from Q_INDEX_DONE and have ENTRY_DATA_PENDING bit set.
From practical standpoint this fixes RX queue stall, usually reproducible
in AP mode, like for example reported here:
https://bugzilla.redhat.com/show_bug.cgi?id=828824
Reported-and-tested-by: Franco Miceli <fmiceli@plan.ceibal.edu.uy>
Reported-and-tested-by: Tom Horsley <horsley1953@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0fde0a8cfd0ede7f310d6a681c8e5a7cb3e32406 upstream.
Fix:
BUG: sleeping function called from invalid context at kernel/workqueue.c:2547
in_atomic(): 1, irqs_disabled(): 0, pid: 629, name: wpa_supplicant
2 locks held by wpa_supplicant/629:
#0: (rtnl_mutex){+.+.+.}, at: [<c08b2b84>] rtnl_lock+0x14/0x20
#1: (&trigger->leddev_list_lock){.+.?..}, at: [<c0867f41>] led_trigger_event+0x21/0x80
Pid: 629, comm: wpa_supplicant Not tainted 3.3.0-0.rc3.git5.1.fc17.i686
Call Trace:
[<c046a9f6>] __might_sleep+0x126/0x1d0
[<c0457d6c>] wait_on_work+0x2c/0x1d0
[<c045a09a>] __cancel_work_timer+0x6a/0x120
[<c045a160>] cancel_delayed_work_sync+0x10/0x20
[<f7dd3c22>] rtl8187_led_brightness_set+0x82/0xf0 [rtl8187]
[<c0867f7c>] led_trigger_event+0x5c/0x80
[<f7ff5e6d>] ieee80211_led_radio+0x1d/0x40 [mac80211]
[<f7ff3583>] ieee80211_stop_device+0x13/0x230 [mac80211]
Removing _sync is ok, because if led_on work is currently running
it will be finished before led_off work start to perform, since
they are always queued on the same mac80211 local->workqueue.
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=795176
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 925839243dc9aa4ef25305f5afd10ed18258a4ac upstream.
Currently we check the sequence number of last packet received
against start_win. If a sequence hole is detected, start_win is
updated to next sequence number.
Since the rx sequence number is initialized to 0, a corner case
exists when BA setup happens immediately after association. As
0 is a valid sequence number, start_win gets increased to 1
incorrectly. This causes the first packet with sequence number 0
being dropped.
Initialize rx sequence number as 0xffff and skip adjusting
start_win if the sequence number remains 0xffff. The sequence
number will be updated once the first packet is received.
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7508b657967cf664b5aa0f6367d05016e7e3bc2a upstream.
https://bugzilla.kernel.org/show_bug.cgi?id=42903
Based on the work of <fynivx@gmail.com>
Signed-off-by: Panayiotis Karabassis <panayk@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f18e3c6b67f448ec47b3a5b242789bd3d5644879 upstream.
"ath9k: Fix softlockup in AR9485" with commit id
64bc1239c790e051ff677e023435d770d2ffa174 fixed the reported
issue, yet its better to avoid the possible infinite loop
in ar9003_get_pll_sqsum_dvc by having a timeout as suggested
by ath9k maintainers.
http://www.spinics.net/lists/linux-wireless/msg92126.html.
Based on my testing PLL's locking measurement is done in
~200us (2 iterations).
Cc: Rolf Offermanns <rolf.offermanns@gmx.net>
Cc: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bcb7ad7bcbef030e6ba71ede1f9866368aca7c99 upstream.
steps to recreate:
load latest ath9k driver with AR9485
stop the network-manager and wpa_supplicant
bring the interface up
Call Trace:
[<ffffffffa0517490>] ? ath_hw_check+0xe0/0xe0 [ath9k]
[<ffffffff812cd1e8>] __const_udelay+0x28/0x30
[<ffffffffa03bae7a>] ar9003_get_pll_sqsum_dvc+0x4a/0x80 [ath9k_hw]
[<ffffffffa05174eb>] ath_hw_pll_work+0x5b/0xe0 [ath9k]
[<ffffffff810744fe>] process_one_work+0x11e/0x470
[<ffffffff8107530f>] worker_thread+0x15f/0x360
[<ffffffff810751b0>] ? manage_workers+0x230/0x230
[<ffffffff81079af3>] kthread+0x93/0xa0
[<ffffffff815fd3a4>] kernel_thread_helper+0x4/0x10
[<ffffffff81079a60>] ? kthread_freezable_should_stop+0x70/0x70
[<ffffffff815fd3a0>] ? gs_change+0x13/0x13
ensure that the PLL-WAR for AR9485/AR9340 is executed only if the STA is
associated (or) IBSS/AP mode had started beaconing. Ideally this WAR
is needed to recover from some rare beacon stuck during stress testing.
Before the STA is associated/IBSS had started beaconing, PLL4(0x1618c)
always seem to have zero even though we had configured PLL3(0x16188) to
query about PLL's locking status. When we keep on polling infinitely PLL4's
8th bit(ie check for PLL locking measurements is done), machine hangs
due to softlockup.
fixes https://bugzilla.redhat.com/show_bug.cgi?id=811142
Reported-by: Rolf Offermanns <rolf.offermanns@gmx.net>
Tested-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d6ee27eb13beab94056e0de52d81220058ca2297 upstream.
When we remove a key, we put a key index which was supposed
to tell the fw that we are actually removing the key. But
instead the fw took that index as a valid index and messed
up the SRAM of the device.
This memory corruption on the device mangled the data of
the SCD. The impact on the user is that SCD queue 2 got
stuck after having removed keys.
The message is the log that was printed is:
Queue 2 stuck for 10000ms
This doesn't seem to fix the higher queues that get stuck
from time to time.
Reviewed-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f380f2c4a12e913356bd49f8790ec1063c4fe9f8 upstream.
This driver disables interrupt just after requesting it and enables it
later, after interface is up. However currently there is a time window
between request_irq() and disable_irq() where if interrupt arrives, the
driver oopses because it's not yet ready to process it. This can be
reproduced by inserting the module, associating and removing the module
multiple times.
Eliminate this race by setting IRQF_NOAUTOEN flag before request_irq().
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 882dde8eb0d49ce0f853f8f4084dde56a21fe55f upstream.
When BT traffic load changes from its
previous state, a new LQ command needs to be
sent down to the firmware. This needs to
be done only once per change. The state
variable that keeps track of this change is
last_bt_traffic_load. However, it was not
being updated when the change had been
handled. Not updating this variable was
causing a flood of advanced BT config
commands to be sent to the firmware. Fix
this.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4c1bcdb5a3354b250b82a67549f57ac27a3bb85f upstream.
This driver currently leaves elp_work behind when stopping, which
occasionally results in data corruption because work function ends
up accessing freed memory, typical symptoms of this are various
worker_thread crashes. Fix it by cancelling elp_work.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 328c32f0f85467af5a6c4c3289e168d9ad2555af upstream.
Currently SDIO glue frees it's own structure before calling
wl1251_free_hw(), which in turn calls ieee80211_unregister_hw().
The later call may result in a need to communicate with the chip
to stop it (as it happens now if the interface is still up before
rmmod), which means calls are made back to the glue, resulting in
freed memory access.
Fix this by freeing glue data last.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 44eb65cfd8da4b9c231238998729e858e963a980 upstream.
Under some circumstances, a PCI-based driver reports the following OOPs:
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] Oops: 0000 [#1] SMP
--snip--
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] Pid: 19627, comm: rmmod
Not tainted 3.2.9-2.fc16.x86_64 #1 LENOVO 05962RU/05962RU
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] RIP:
0010:[<ffffffffa0418d39>] [<ffffffffa0418d39>]
rtl92ce_get_desc+0x19/0xd0 [rtl8192ce]
--snip--
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] Process rmmod (pid:
19627, threadinfo ffff880050262000, task ffff8801156d5cc0)
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] Stack:
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] 0000000000000002
ffff8801176c2540 ffff880050263ca8 ffffffffa03348e7
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] 0000000000000282
0000000180150014 ffff880050263fd8 ffff8801176c2810
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] ffff880050263bc8
ffffffff810550e2 00000000000002c0 ffff8801176c0d40
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] Call Trace:
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] [<ffffffffa03348e7>]
_rtl_pci_rx_interrupt+0x187/0x650 [rtlwifi]
--snip--
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] Code: ff 09 d0 89 07 48
83 c4 08 5b 5d c3 66 0f 1f 44 00 00 55 48 89 e5 53 48 83 ec 08 66 66
66 66 90 40 84 f6 89 d3 74 13 84 d2 75 57 <8b> 07 48 83 c4 08 5b 5d c1
e8 1f c3 0f 1f 00 84 d2 74 ed 80 fa
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] RIP
[<ffffffffa0418d39>] rtl92ce_get_desc+0x19/0xd0 [rtl8192ce]
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] RSP <ffff880050263b58>
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] CR2: 00000000000006e0
Mar 19 08:14:35 kvothe kernel: [ 6584.646491] ---[ end trace
8636c766dcfbe0e6 ]---
This oops is due to interrupts not being disabled in this particular path.
Reported-by: Dave Airlie <airlied@gmail.com>
Tested-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dd447319895d0c0af423e483d9b63f84f3f8869a upstream.
Driver incorrectly validates command completion: instead of waiting
for a command to be acknowledged it continues execution. Most of the
time driver gets acknowledge of the command completion in a tasklet
before it executes the next one. But sometimes it sends the next
command before it gets acknowledge for the previous one. In such a
case one of the following error messages appear in the log:
Failed to send SYSTEM_CONFIG: Already sending a command.
Failed to send ASSOCIATE: Already sending a command.
Failed to send TX_POWER: Already sending a command.
After that you need to reload the driver to get it working again.
This bug occurs during roaming (reported by Sam Varshavchik)
https://bugzilla.redhat.com/show_bug.cgi?id=738508
and machine booting (reported by Tom Gundersen and Mads Kiilerich)
https://bugs.archlinux.org/task/28097
https://bugzilla.redhat.com/show_bug.cgi?id=802106
This patch doesn't fix the delay issue during firmware load.
But at least device now works as usual after boot.
Signed-off-by: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
