| Age | Commit message (Collapse) | Author |
|---|
|
WLVIF_FLAG_PSM turned to WLVIF_FLAG_IN_AUTO_PS which
marks that this vif is in AUTO PS.
WLVIF_FLAG_PSM_REQUESTED is not required as mac80211
calls op_config with CONF_PS after association.
wl12xx_config_vif() handling of CONF_PS was simplified
and cleaned up.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
While the FW with dynamic PS controls BET when going to PSM and back
internally within the FW, there's still a need to enable it from the driver
at least once (so enable on every entry to AUTO_PS)
and disable it once we explicitly go back to STATION_ACTIVE_MODE.
BET isn't relevant for 5GHz
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
cleanup 2 unused parameters of wl1271_ps_set_mode
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
Enable read/write of dynamic_ps_timeout which controls the timeout
of the dynamic PS implemented in the FW.
dynamic_ps_timeout is the timeout (in msec) until going back to PS
when there's no Rx/Tx
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
FW now supports dynamic PS so we don't need to use mac80211 support.
FW will go to PSM after a specified timeout with no Rx/Tx traffic.
- Changed FW API to include new PS mode (AUTO_MODE) and including timeout parameter
- The default PS mode would be dynamic PS
- Default timeout is 100ms (same as it used to be in mac80211)
- Avoid using mac80211 APIs to disable/enable dynamic PS as we're not
using mac80211 PS control anymore.
- COEX is handled by the FW while in dynamic PS so removed
handling of SOFT_GEMINI
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
Removal of PS management code from the driver as PS
is handled by the FW (dynamic PS)
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
Update enums/structs to the new fw api.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
The ACX_TSF_INFO command now takes role_id as param.
change the struct accordingly, and pass the wlvif
to the wl1271_acx_tsf_info() function.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
Use device role for scans when the sta is not
associated.
sched_scan is used only when the sta is
not associated, and thus should use
the dev role (instead of sta role).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
The set_template commands now takes the role_id as
parameter.
Usually, we'll use the vif's main role_id.
However, sometimes we'll want to use
wlvif->dev_role_id instead of wlvif->role_id,
so pass the wanted role_id as param.
Update WL127X_FW_NAME/WL128X_FW_NAME.
(This commit starts a series of fw update patches,
and changes the start() callback to return an error
in order to prevent the use of the driver during the
transition. This change will be reverted in the
last patch of series)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
Since we reverted to claiming the host only when needed,
we no longer need to release/claim the host on suspend/resume.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
This reverts commit 393fb560d328cc06e6a5c7b7473901ad724f82e7.
Commit b6ad726 ("mmc: core: Prevent too long response times
for suspend") fails the suspend if the mmc host can't be
claimed before suspend. As the host is claimed by us as long
as the chip is powered on, suspend will always fail.
Revert to claiming the sdio bus only when needed.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
wl1271_tx_update_filters() is used as some workaround
to open filters while roaming on the same channel.
However, it doesn't handle roaming to a different channel,
and it might also sleep in the tx path, which is a bug.
With the new auth/assoc redesign, roaming is much simpler,
and this function is not needed anymore.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
with the new auth/assoc redesign, we get CHANGED_BSSID
indication before CHANGED_ASSOC indication, while our
CHANGED_BSSID handling block assumes we are already
associated.
Fix it by checking we are either in ibss mode, or
already associated.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
Fix a copy and paste bug in the MODULE_PARAM_DESC for fwlog.
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
The vif variable was being declared inside one of the internal blocks
of wl1271_event_process. This is not necessary, since this variable
is already declared in the function context.
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
Add a testmode command to retrieve the BD_ADDR that is stored in the
Fuse ROM in newer PGs. In old PGs this operation is not supported.
The caller can then derive the MAC addresses from it.
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
Add support for two MAC addresses. If the NVS has a valid MAC
address, that takes precedence and we use two sequential address
starting from the one specified.
If the NVS doesn't contain a valid MAC address (ie. if it is set to
00:00:00:00:00:00), we check if the HW PG version in use has the
BD_ADDR written in the fuse ROM. If it does, we read it and derive
the two subsequent addresses for WLAN.
During production, 3 addresses are reserved per device. The first for
Bluetooth (burnt in the fuse ROM) and the following two for WLAN.
This patch has some code by Igal and Arik (squashed from internal
patches).
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Igal Chernobelsky <igalc@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
In order to read the MAC addresses from the fuse ROM, we need to know
the chip ID and the HW PG version. We need to know the MAC address
during probe, because that's when we register our HW with mac80211.
To prepare for that, this patch reads the chip ID and HW PG version
during probe instead of doing it at boot time. We power the chip on
briefly in order to do that.
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
Up till now we only needed to access the partition table in boot.c.
But to add support for reading the MAC address from the FUSE in
testmode, we will have to change the partition in testmode.c.
Thus, we move the partition table to io.c and export it via io.h. It
makes more sense to have it in the io part anyway.
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
In some cases a race condition can happen if we don't cancel any
pending ELP work before stopping PLT. With this commit we cancel ELP
work and clear the wl->flags bitmask. Also clean up the wl elements
after powering off.
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
The interrupt threaded handler exits immediately if the driver's state
is WL1271_STATE_OFF. As a result, the interrupt status is not read. If
the interrupt is level triggered, it will be fired again.
Fix this by disabling interrupts before setting the state to OFF.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
When stopping plt, the chip is powered off before all current work items
are flushed and interrupts are disabled. This might introduce a race in
which the driver tries to communicate with a powered off chip.
Fix this by powering off the device only after interrupts are disabled
and all work items are flushed.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
__wl1271_plt_stop is called from both wl1271_plt_stop and
wl1271_unregister_hw. While wl1271_plt_stop acquires a mutex,
wl1271_unregister_hw does not.
Fix this by calling wl1271_plt_stop instead of __wl1271_plt_stop from
wl1271_unregister_hw.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
The sched_scan_(stop|start) ops fails to check for WL1271_STATE_OFF.
This can lead to a race where the driver tries to access the HW
while it's off.
Fix this by checking for WL1271_STATE_OFF before accessing the HW.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
Following the good example of the Intel (and more recently Atheros)
drivers, enable endianess check by default when running sparse.
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
Similar to the previous beacon filtering patch,
make CQM RSSI support depend on the flags that
the driver set for virtual interfaces.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Due to firmware limitations, we may not be able to
support beacon filtering on all virtual interfaces.
To allow this in mac80211, introduce per-interface
driver capability flags that the driver sets when
an interface is added.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
stop sched scan isn't an immediate operation
and we need to wait for PERIODIC_SCAN_COMPLETE_EVENT_ID
after sending a stop before changing internal state
and notifying upper layers.
Not doing this caused problems when canceling an existing sched
scan and immediately requesting to start a new one
with a different configuration as the FW was still
in the middle of the previous sched scan.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
DFS channels weren't scanned properly because
min/max_duration weren't set for these channels
even though they're required by the FW.
The change sets passive_duration and min/max_duration
for all channels as the FW uses the correct parameters
according to the channel type.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
The wl12xx_platform_data.c file did not have a proper copyright
notice.
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
The current wl1271_dev_notify implementation sets the
new operstate to all associated stations (while only
a specific vif was changed).
Until we'll have a method to get the actual vif from
the given dev, check the current operstate of each vif.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
When removing a sta/ibss role, the device role has to
stopped (and disabled) as well.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
dev_role_id only indicates whether the dev role
is enabled, not started (e.g. on IBSS merge,
the device role is enabled, but not started).
Checking for any role in ROC (in order to determine
whether dev role was started) is wrong as well,
especially in multi-vif env.
Check for started dev role only by checking the dev_hlid.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
During sta disconnection, a deauth packet is being queued to
the dev role queue. However, the dev role is being stopped
before the packet was sent.
Flush the tx queue before stopping the dev role.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
This flag should be set per-vif, rather than globally.
Rename the flag to indicate IN_USE (rather than IDLE), as
in the default configuration (i.e. flag is clear) the vif
should be idle.
Change all the bit operations (and elp conditions) appropriately.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
Since the conf_tx callback passes the vif as param,
we must have been added first (and mac80211 verifies it).
Remove the handling of such case.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
Implement the change_interface callback by simply removing the
current vif and adding a new one after updating the vif type.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
When compiling wl12xx for x86, there was a warning complaining about
the size of the buffer we were allocating in the stack:
drivers/net/wireless/wl12xx/debugfs.c: In function 'driver_state_read':
drivers/net/wireless/wl12xx/debugfs.c:380:1: warning: the frame size of 1040 bytes is larger than 1024 bytes
To prevent this, allocate the buffer in the heap instead.
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
wl1271_configure_suspend_sta leaves a stale stack declared
completion in wlvif->ps_compl. Set it to NULL before returning.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
[small fix to use wlvif->ps_compl instead of wl->ps_compl]
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
We don't use WL12XX_BA_SUPPORT_FW_COST_VER2_START nor
WL12XX_BA_SUPPORT_FW_COST_VER2_END anymore.
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
The ACX_PD_THRESHOLD configuration command is deprecated and should
not be used anymore.
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
Use the newly introduced ieee80211_free_txskb() instead
of dev_kfree_skb() for failed tx packets.
Additionally, if the skb is a dummy packet, re-enqueue
it (as the fw expects it) instead of freeing it.
Reported-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
We need to set the extended radio parameters for wl127x only.
Currently, we were only calling this command with wl127x STA mode, but
we should also do it for AP mode.
Move the call to the extended radio paramaters to the common hw_init
and use a single if for the chip type to do everything at once.
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
We should not get an hlid value bigger than WL12XX_MAX_LINKS from
wl1271_rx_handle_data(). We have a WARN_ON in case it happens. But
despite the warning, we would still go ahead and write the hlid bit
into active_hlids (a stack variable). This would cause us to
overwrite other data in the stack.
To avoid this problem, we now skip the write when issuing the warning,
so at least we don't corrupt data.
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
Commit 80900d0140a7648587982c8f299830e900e49165 accidently broke
the ABI for testmode commands. Restore the ABI again.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
CC [M] drivers/net/wireless/wl12xx/tx.o
drivers/net/wireless/wl12xx/tx.c: In function ‘wl1271_tx_fill_hdr’:
drivers/net/wireless/wl12xx/tx.c:288:6: warning: ‘tx_attr’ may be used uninitialized in this function
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The user can pass broadcast SSID (ssid="") in the list of SSIDs for active scan.
In this case the loop was attempting to match SSIDs in the filter
list to this empty entry and marking them as HIDDEN (sending probe
request) by mistake
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
wl1271_tm_cmd_interrogate creates a reply skb, but doesn't
send it (and thus just leaks it).
Add the missing cfg80211_testmode_reply() call.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
During plt init we configure some redundant commands,
which are not needed for plt (specifically, we shouldn't
configure any role-specific params, as there are no
active roles). remove them.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
