aboutsummaryrefslogtreecommitdiff
path: root/drivers/net/wireless/rt2x00/rt2x00config.c
AgeCommit message (Collapse)Author
2010-10-05rt2x00: Implement HT protection for rt2800Helmut Schaa
Update the HT operation mode when mac80211 sends it to us and set the different HT protection modes and rates accordingly. For now only use CTS-to-self with OFDM 24M or CCK 11M when protection is required. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-09-14rt2x00: Check for specific changed flags when updating the erp configHelmut Schaa
Previously rt2x00 was always updating all erp related config variables even though mac80211 might only have changed one. Hence, pass the changed flags to the config_erp driver callback so that the driver can limit the changes to the correct values. This fixes an issue in AP mode where the beacon interval is not initialized (and thus zero) but still sent to the hardware causing an interrupt storm on rt2800pci hanging the system. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-09-14rt2x00: Antenna diversity does not work in 2.6.35Lars Ericsson
The test if antenna diversity is at all enabled uses a local variable 'flags' to prepare the test condition, but uses 'ant->flags' when the test is evaluated. The effect is that the diversity evaluation will never start. I can see two solutions, use the 'flag' in the test condition or revert the local flag change. My attached patch took alternative two. Then the evaluation start but it will still not switch antenna. The problem is a code section in rt2x00lib_config_antenna (). The effect of that code section is that any change the diversity function perform will be effectively shorten and no antenna selection command issued. The attached patch will filter out any ANTENNA_SW_DIVERSITY setting but forward all other Signed-off-by: Lars Ericsson <lars_ericsson@telia.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-16rt2x00: Remove ieee80211_rx_status from rt2x00_devIvo van Doorn
rt2x00 was keeping a copy of ieee80211_rx_status embedded into the rt2x00_dev structure. For each RX frame, this structure was copied into the skb->cb where mac80211 would handle it further. However at the moment only the fields current band, and frequency were updated. Whereas the band was already provided directly within the rt2x00_dev structure. Save a memcpy action, and reduce memory a bit, by adding a curr_freq field to rt2x00_dev, and completely remove the ieee80211_rx_status structure from rt2x00_dev. Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-16rt2x00: do not shortcut rt2x00lib_config_antennaJohn W. Linville
This function was exiting early if the existing diversity settings were unchanged. Unfortunately, in some cases the antenna configuration is not initialized at all. https://bugzilla.kernel.org/show_bug.cgi?id=14751 Signed-off-by: John W. Linville <linville@tuxdriver.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Cc: Gertjan van Wingerde <gwingerde@gmail.com>
2010-07-12rt2x00: Add missing TSF sync mode for AP operationHelmut Schaa
Currently rt2x00 uses the TSF_SYNC_BEACON mode for all beaconing interface types. However, TSF_SYNC_BEACON is meant for IBSS networks and thus implements TSF merging in the hardware. Rename TSF_SYNC_BEACON to TSF_SYNC_ADHOC to better express its purpose and introduce the missing TSF sync mode TSF_SYNC_AP_NONE which should be used for beaconing modes that don't need TSF merging. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-03rt2x00: Fix HT40 operation in rt2800.Gertjan van Wingerde
Closer inspection of the legacy Ralink driver reveals that in case of HT40+ or HT40- we must adjust the frequency settings that we program to the device. Implement the same adjustment in the rt2x00 code. With this HT40 seems to work for all devices supported by rt2800pci and rt2800usb. Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
2009-11-11rt2x00: Update copyright statements.Gertjan van Wingerde
As mentioned on the linux-wireless mailing list, the current copyright statements in the rt2x00 are meaningless, as the rt2x00 project is not even a formal legal entity. Therefore it is better to replace the existing copyright statements with copyright statements for the people that actually wrote the code. Note: Updated to the best of my knowledge with respect to who contributed considerable amounts of code. Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> CC: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-09-09rt2x00: Hardcode TX ack timeout and consume timeIvo van Doorn
The calculated values for the ACK timeout and ACK consume time are different then the values as used by the Legacy drivers. After testing from James Ledwith it appeared that the calculated values caused a high amount of TX failures, and the values from the Legacy drivers were the most optimal to prevent TX failure due to excessive retries. The symptoms of this problem: - Rate control module always falls back to 1Mbs - Low throughput when bitrate was fixed Possible side-effects (not confirmed but highly likely) - Problems with DHCP - Broken connections due to lack of probe response This should fix at least: Kernel bugzilla reports: [13362], [13009], [9273] Fedora bugzilla reports: [443203] but possible some additional bugs as well. Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-14rt2x00: Remove usage of deprecated radio_enabled & ↵Ivo van Doorn
IEEE80211_CONF_CHANGE_RADIO_ENABLED In the config() callback function the fields radio_enabled and the change flag IEEE80211_CONF_CHANGE_RADIO_ENABLED have been deprecated. This removes the usage of those fields by improving antenna change detection in the antenna configuration function. Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-27rt2x00: Don't alter rt2x00dev->default_antLars Ericsson
rt2x00dev->default_ant should be initialized once by the driver, and should not be changed afterwards. Because rt2x00lib_config_antenna() was using a reference to the struct antenna_setup it actually had the oppurtunity to change the default antenna setting and it actually did that during the validation. Instead of passing a pointer to antenna_setup the entire structure should be copied. Signed-off-by: Lars Ericsson <Lars_Ericsson@telia.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-24rt2x00: Comment spellcheckingLuis Correia
Fix a bunch of spelling errors in the rt2x00 drivers Signed-off-by: Luis Correia <luis.f.correia@gmail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-06-03rt2x00: Remove last usage of beacon_int from ieee80211_configIvo van Doorn
This removes the last usage of beacon_int inside the iee80211_config structure from rt2x00. The attempt is a bit hackish, and subject to change in the future when the entire rt2x00_dev structure is cleaned up and restructured. Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-05-22rt2x00: Remove usage of IEEE80211_CONF_CHANGE_BEACON_INTERVALIvo van Doorn
IEEE80211_CONF_CHANGE_BEACON_INTERVAL was deprecated a month ago, it is about time to remove all usage from the rt2x00 drivers and use the correct beacon interval configuration through the bss_info structure. Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-05-06rt2x00: Implement support for 802.11nIvo van Doorn
Extend rt2x00lib capabilities to support 802.11n, it still lacks aggregation support, but that can be added in the future. Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29mac80211: constify ieee80211_if_conf.bssidJohannes Berg
Then one place can be a static const. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29rt2x00: Update copyright year to 2009Ivo van Doorn
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29rt2x00: Implement WDS supportIvo van Doorn
WDS support should be very easy to handle, mac80211 handles everything for us, so all that is needed is to set the support flags and handle it in the add_interface() callback. Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29rt2x00: Add mesh supportAndrey Yurovsky
This adds initial support for Mesh Point mode. For this we tell mac80211 that we support NL80211_IFTYPE_MESH_POINT. We also need to send beacons. mac80211 will configure our RX filter accordingly. Signed-off-by: Andrey Yurovsky <andrey@cozybit.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29rt2x00: Move link tuning into seperate fileIvo van Doorn
Move link and antenna tuning into a seperate file named rt2x00link.c, this makes the interface to the link tuner a lot cleaner. Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-12-05rt2x00: Remove duplicate codeIvo van Doorn
Simplify rt2x00lib_config_antenna() by moving duplicate code into a seperate static inlined function. Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-12-05rt2x00: Store retry limit valuesIvo van Doorn
Store retry limit values in the rt2x00dev structure. This allows the removal of the FIXME where we assumed the long retry is only used when working with RTS frames. Instead we should check the current retry limit values and decide if the required retry count for this frame is a long or short retry. Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-11-21rt2x00: Optimize get_duration / get_duration_resIvo van Doorn
We can optimize get_duration and get_duration_res by making them a macro. They are really simple calculation handlers so this doesn't matter much. Often (especially in rt2400pci and rt2500pci, the arguments are hardcoded, and the result value is passed into other hardcoded values. By making the functions a macro GCC can optimize the entire thing much better. Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-11-21rt2x00: Fix BUG_ON() with antenna handlingIvo van Doorn
With the new configuration handling, and more specifically splitting the configuration of the antenna from the normal configuration steps allowed a BUG_ON() to be triggered in the driver because the SW_DIVERSITY was send to the driver. This fixes that by catching the value early in rt2x00config.c and replacing it with a sensible value. This also fixes a problem where the antenna is not being initialized at all when the radio is enabled. Since it no longer is part of the mac80211 configuration the only place where rt2x00 configured it was the SW diversity handler. Obviously this is broken for all non-diversity hardware and breaks SW diversity due to a broken initialization. When the radio is enabled the antenna will be configured once as soon as the config() callback function is called. Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-11-10rt2x00: Optimize configuration handlingIvo van Doorn
Implement latest changed from mac80211 configuration handling to optmize configuration handling in rt2x00. * Remove set_retry_limit callback function, handled through config() * Move config_antenna to its own callback function, it isn't handled by mac80211 anymore * Use IEEE80211_CONF_CHANGED_* flags and remove manual checks * Removed deprecated short slot setting through config() and put it in config_erp() through which mac80211 now configures it * Remove config_phymode() and move contents to config_erp() since it only managed the basic rates which is now determined by mac80211 through config_erp(). Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-10-31mac80211: kill hw.conf.antenna_sel_{rx,tx}Johannes Berg
Never actually used. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-09-15mac80211: use nl80211 interface typesJohannes Berg
There's really no reason for mac80211 to be using its own interface type defines. Use the nl80211 types and simplify the configuration code a bit: there's no need to translate them any more now. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-08-29rt2x00: Fix race conditions in flag handlingIvo van Doorn
Some of the flags should be accessed atomically to prevent race conditions. The flags that are most important are those that can change often and indicate the actual state of the device, queue or queue entry. The big flag rename was done to move all state flags to the same naming type as the other rt2x00dev flags and made sure all places where the flags were used were changed. ;) Thanks to Stephen for most of the queue flags updates, which fixes some of the most obvious consequences of the race conditions. Among those the notorious: rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 0. rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 0. rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 0. Signed-off-by: Stephen Blackheath <tramp.enshrine.stephen@blacksapphire.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-08-22rt2x00: Gather channel information in structureIvo van Doorn
Channel information which is read from EEPROM should be read into an array containing per-channel information. This removes the requirement of multiple arrays and makes the channel handling a bit cleaner and easier to expand. Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-08-01rt2x00: Fix partial antenna configurationIvo van Doorn
The if-statement to determine the new TX/RX antenna configuration was incomplete. It lacks the general else-clause when the antenna wasn't changed. This is a correct event, since it can occur when only one of the antenna's has been changed or when the new configuration is being forced (like when the interface has just been added). Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-07-29rt2x00: Fix EIFS timing valueIvo van Doorn
Olivier reported a difference between the EIFS values used in the legacy driver and the one in the rt2x00 drivers. In rt2x00 the value was ( SIFS + (8 * (IEEE80211_HEADER + ACK_SIZE)) ) which comes down to 314us while the legacy driver uses the value 364us This was caused because EIFS is: SIFS + DIFS + AckTime This patch will fix this by adding the DIFS by the above value, and creating a SHORT_EIFS define which uses the SHORT_DIFS. Reported-by: Olivier Cornu <o.cornu@gmail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-07-14rt2x00: Add support for CTS protection in rt2x00libIvo van Doorn
Inform drivers about the changed CTS protection settings. Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-05-28rt2x00: Reset antenna RSSI after switchIvo van Doorn
When the antenna configuration has changed we should reset the antenna RSSI value. Otherwise the value will be influenced by the previous configuration quality which in turn will affect the antenna diversity. Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-03-25rt2x00: Fix in_atomic() usageIvo van Doorn
rt73usb and rt2500usb used in_atomic to determine if a configuration step should be rescheduled or not. Since in_atomic() is not a valid method to determine if sleeping is allowed we should fix the way this is handled by adding a new flag to rt2x00. In addition mark LED class support for the drivers broken since that also uses the broken in_atomic() method but so far no solution exists to have LED triggers work only in scheduled context. Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-03-13rt2x00: Fix basic rate initializationIvo van Doorn
The basic rate which is configured in the register should not match all supported rates, but only the _basic_ rates. Fix this by adding a new flag to the rt2x00_rate structure and whenever the mode is changed, loop over all available rates for that band to get the basic rate mask. Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-03-13rt2x00: Rename config_preamble() to config_erp()Ivo van Doorn
Rename config_preamble() to config_erp() and cleanup argument list by putting it all into a single structure. This will make the function more meaningful and easier to expand later. This second option is mostly intended to make the patch "mac80211: proper short-slot handling" from Johannes Berg easier to apply for rt2x00. Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-02-29rt2x00: Remove HWMODE_{A,B,G}Ivo van Doorn
rt2500usb initialized the SIFS and EIFS without using the values coming from rt2x000lib. After this is fixed HWMODE_{A,B,G} is now unused and can be removed in favour of the ieee80211_band enumeration which could still be usefull later. Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-02-29rt2x00: Rate structure overhaulIvo van Doorn
Recent changes to the rate structure registration broke rt2x00, the hw_value was reduced from 32bits to 16bits while rt2x00 used the full 32bits. However the way rt2x00 used the value was inflexible and needed to be changed anyway. This patch creates a array containing information for each rate, the hw_value passed to mac80211 is the index value for that array including a field to indicate if short preamble should be enabled. Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-02-29cfg80211 API for channels/bitrates, mac80211 and driver conversionJohannes Berg
This patch creates new cfg80211 wiphy API for channel and bitrate registration and converts mac80211 and drivers to the new API. The old mac80211 API is completely ripped out. All drivers (except ath5k) are updated to the new API, in many cases I expect that optimisations can be done. Along with the regulatory code I've also ripped out the IEEE80211_HW_DEFAULT_REG_DOMAIN_CONFIGURED flag, I believe it to be unnecessary if the hardware simply gives us whatever channels it wants to support and we then enable/disable them as required, which is pretty much required for travelling. Additionally, the patch adds proper "basic" rate handling for STA mode interface, AP mode interface will have to have new API added to allow userspace to set the basic rate set, currently it'll be empty... However, the basic rate handling will need to be moved to the BSS conf stuff. I do expect there to be bugs in this, especially wrt. transmit power handling where I'm basically clueless about how it should work. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-02-29rt2x00: Add per-interface structureIvo van Doorn
Rework the interface handling. Delete the interface structure and replace it with a per-interface structure. This changes the way rt2x00 handles the active interface drastically. Copy ieee80211_bss_conf to the this rt2x00_intf structure during the bss_info_changed() callback function. This will allow us to reference it later, and removes the requirement for the device flag SHORT_PREAMBLE flag which is interface specific. Drivers receive the option to give the maximum number of virtual interfaces the device can handle. Virtual interface support: rt2400pci: 1 sta or 1 ap, * monitor interfaces rt2500pci: 1 sta or 1 ap, * monitor interfaces rt2500usb: 1 sta or 1 ap, * monitor interfaces rt61pci: 1 sta or 4 ap, * monitor interfaces rt73usb: 1 sta or 4 ap, * monitor interfaces At the moment none of the drivers support AP and STA interfaces simultaneously, this is a hardware limitation so future support will be very unlikely. Each interface structure receives its dedicated beacon entry, with this we can easily work with beaconing while multiple master mode interfaces are currently active. The configuration handlers for the MAC, BSSID and type are often called together since they all belong to the interface configuration. Merge the 3 configuration calls and cleanup the API between rt2x00lib and the drivers. While we are cleaning up the interface configuration anyway, we might as well clean up the configuration handler as well. Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-02-29rt2x00: Update copyright noticeIvo van Doorn
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-02-28rt2x00: Don't switch to antenna with low rssiIvo van Doorn
When rssi_a > rssi_b is true and the current antenna was already antenna A, then rt2x00 incorrectly jumped to antenna B. Also don't configure the antenna when there has been no change in the antenna setup. Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-02-28rt2x00: Add link tuner safe RX toggle statesIvo van Doorn
This adds 2 new states which both are used to toggle the RX. These new states are required for usage inside the link tuner thread, because the normal RX toggling will stop the link tuner thread. While it is possible that the link tuner thread itself is the caller of the RX toggle (when using software antenna diversity). Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28rt2x00: Replace DRV_NAME with KBUILD_MODNAMEIvo van Doorn
DRV_NAME was always set to the KBUILD_MODNAME value, lets clean everything up by removing DRV_NAME and just use KBUILD_MODNAME directly. Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28rt2x00: Disable RX when switching antennaIvo van Doorn
Antenna switching will be ignored when RX is enabled during the switch. Make sure we disable the RX during the switch and don't forget to reenable it later. Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28[PATCH] rt2x00: Fix antenna selection.Mattias Nissler
In the config() handler, make sure that we do configure an antenna if the current active antenna is uninitialized. Furthermore, don't overwrite the active antenna with bogus values if we didn't touch the antenna setup. Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28[PATCH] rt2x00: Implement SW diversityIvo van Doorn
When mac80211 indicates that the default antenna setup should be used _and_ that this default setup is SW_DIVERSITY. This requires sampling and storing the RSSI per antenna and check once every 2 seconds to determine if the RSSI has changed significantly. Once this is the case we should sample the other antenna for a short period and evaluate if we need to swap antenna or not. Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28[PATCH] rt2x00: Correctly translate mac80211 antenna setup to rt2x00Ivo van Doorn
mac80211 has 3 values for the antenna setup: 0 - default 1 - use antenna 1 2 - use antenna 2 This means that rt2x00 should store the default value from the EEPROM somwhere and use that when mac80211 indicates that the antenna setup is 0. This also implies that rt2x00 should no longer write the hw->config.antenna_sel_* values based on the EEPROM input. This also adds the basis in rt2x00lib for correct software diversity handling. By default rt2x00lib will now configure antenna B instead of hardware diversity. Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-10-10[PATCH] rt2x00: Reorganize configuration handlerIvo van Doorn
Reorganize configuration handling by creating a extra structure which contains precalculated values based on the mac80211 values which are usefull for all individual drivers. This also fixes the preamble configuration problem, up untill now preamble was never configured since by default the rate->val value was used when changing the mode. Now rate->val will only be used to set the basic rate mask. The preamble configuration will now be done correctly through the erp_ie_changed callback function. Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-10-10[PATCH] rt2x00: Move TSF sync values into rt2x00configIvo van Doorn
All drivers use the same values for TSF sync, this will move the value determination into rt2x00config.c, and the definition for the values to rt2x00reg.h Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>