| Age | Commit message (Collapse) | Author |
|---|
|
sta_rc_update() callback must be atomic, hence we can not take mutexes
or do other operations, which can sleep in ath9k_htc_sta_rc_update().
I think we can just return from ath9k_htc_sta_rc_update(), if it is
called without IEEE80211_RC_SUPP_RATES_CHANGED bit. That will help
with scheduling while atomic bug for most cases (except mesh and IBSS
modes).
For mesh and IBSS I do not see other solution like creating additional
workqueue, because sending firmware command require us to sleep, but
this can be done in additional patch.
Patch partially fixes bug:
https://bugzilla.redhat.com/show_bug.cgi?id=990955
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Aids in understanding excactly what a firmware is
offering.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
|
|
ARP frames exchange does not work properly for UAPSD enabled AP.
ARP requests which arrives with access category 0 are processed
by network stack and send back with access category 0. FW changes
access category to 6. This is causing problems when UAPSD associated
STA is sleeping after has sent ARP request. Configure ARP access
category in FW to best effort (0) solves this problem. ARP frames
will be send with access category 0.
Simplify arp ac override functionality by removing redundant entry in
pdev param maping table. There should be only one entry in pdev param
map but enum has different name for different FW.
kvalo: change the warning message
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
If recovery failed ath10k returned 0 (success) and
mac80211 continued to call other driver callbacks.
This caused null dereference.
This is how the failure looked like:
ath10k: ctl_resp never came in (-110)
ath10k: failed to connect to HTC: -110
ath10k: could not init core (-110)
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<ffffffffa0b355c1>] ath10k_ce_send+0x1d/0x15d [ath10k_pci]
PGD 0
Oops: 0000 [#1] PREEMPT SMP
Modules linked in: ath10k_pci ath10k_core ath5k ath9k ath9k_common ath9k_hw ath mac80211 cfg80211 nf_nat_ipv4 ]
CPU: 1 PID: 36 Comm: kworker/1:1 Tainted: G WC 3.13.0-rc8-wl-ath+ #8
Hardware name: To be filled by O.E.M. To be filled by O.E.M./HURONRIVER, BIOS 4.6.5 05/02/2012
Workqueue: events ieee80211_restart_work [mac80211]
task: ffff880215b521c0 ti: ffff880215e18000 task.ti: ffff880215e18000
RIP: 0010:[<ffffffffa0b355c1>] [<ffffffffa0b355c1>] ath10k_ce_send+0x1d/0x15d [ath10k_pci]
RSP: 0018:ffff880215e19af8 EFLAGS: 00010292
RAX: ffff880215e19b10 RBX: 0000000000000000 RCX: 0000000000000018
RDX: 00000000d9ccf800 RSI: ffff8800c965ad00 RDI: 0000000000000000
RBP: ffff880215e19b58 R08: 0000000000000002 R09: 0000000000000000
R10: ffffffff812e1a23 R11: 0000000000000292 R12: 0000000000000018
R13: 0000000000000000 R14: 0000000000000002 R15: ffff88021562d700
FS: 0000000000000000(0000) GS:ffff88021fa80000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000000 CR3: 0000000001a0d000 CR4: 00000000000407e0
Stack:
d9ccf8000d47df40 ffffffffa0b367a0 ffff880215e19b10 0000000000000010
ffff880215e19b68 ffff880215e19b28 0000000000000018 ffff8800c965ad00
0000000000000018 0000000000000000 0000000000000002 ffff88021562d700
Call Trace:
[<ffffffffa0b3251d>] ath10k_pci_hif_send_head+0xa7/0xcb [ath10k_pci]
[<ffffffffa0b16cbe>] ath10k_htc_send+0x23d/0x2d0 [ath10k_core]
[<ffffffffa0b1a169>] ath10k_wmi_cmd_send_nowait+0x5d/0x85 [ath10k_core]
[<ffffffffa0b1aaef>] ath10k_wmi_cmd_send+0x62/0x115 [ath10k_core]
[<ffffffff814e8abd>] ? __netdev_alloc_skb+0x4b/0x9b
[<ffffffffa0b1c438>] ath10k_wmi_vdev_set_param+0x91/0xa3 [ath10k_core]
[<ffffffffa0b0e0d5>] ath10k_mac_set_rts+0x3e/0x40 [ath10k_core]
[<ffffffffa0b0e1d0>] ath10k_set_frag_threshold+0x5e/0x9c [ath10k_core]
[<ffffffffa09d60eb>] ieee80211_reconfig+0x12a/0x7b3 [mac80211]
[<ffffffff815a8069>] ? mutex_unlock+0x9/0xb
[<ffffffffa09b3a40>] ieee80211_restart_work+0x5e/0x68 [mac80211]
[<ffffffff810c01d0>] process_one_work+0x1d7/0x2fc
[<ffffffff810c0166>] ? process_one_work+0x16d/0x2fc
[<ffffffff810c06c8>] worker_thread+0x12e/0x1fb
[<ffffffff810c059a>] ? rescuer_thread+0x27b/0x27b
[<ffffffff810c5aee>] kthread+0xb5/0xbd
[<ffffffff815a9220>] ? _raw_spin_unlock_irq+0x28/0x42
[<ffffffff810c5a39>] ? __kthread_parkme+0x5c/0x5c
[<ffffffff815ae04c>] ret_from_fork+0x7c/0xb0
[<ffffffff810c5a39>] ? __kthread_parkme+0x5c/0x5c
Code: df ff d0 48 83 c4 18 5b 41 5c 41 5d 5d c3 55 48 89 e5 41 57 41 56 45 89 c6 41 55 41 54 41 89 cc 53 48 89
RIP [<ffffffffa0b355c1>] ath10k_ce_send+0x1d/0x15d [ath10k_pci]
RSP <ffff880215e19af8>
CR2: 0000000000000000
Reported-By: Ben Greear <greearb@candelatech.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Until now ath10k used a copy-by-value beacon
submission.
The new method passes a DMA address via WMI
command only. This command contains additional
metadata that fixes AP behaviour with regard
to powersave buffering.
This also fixes strange bug when multicast traffic
would freeze TX indefinitely.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Most channel switching logic has been implemented
already so this patch is pretty small. The patch
makes use of mac80211's vif->csa_active for AP CSA
handling.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Until now channel change wasn't propagating to FW
directly because operational channel is abstracted
by VDEVs and it wasn't really necessary since
ath10k implements hwscan and hwroc.
This effectively fixes STA CSA and allows for
future AP-like CSA as well.
kvalo: change error handling in ath10k_bss_info_changed()
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
The threshold values for RX interrupt mitigation
are different for AR9003 and AR9002 families.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The commit "ath9k: Process GTT interrupts" accidentally
had a line that was commented out.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
10.x FW has no structure member sw_version_1. Thus,
both fw_version_release and fw_version_build are not
available. The provided fw_version_major is also wrong.
Fix this by using the fw_version from struct wiphy.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
ath10k handles UAPSD completly in the firmware.
When works in AP mode we have to configure
UAPSD params for each station. Without this
patch we configure UAPSD params before we
send peer assoc command to the FW, which was
wrong. Next FW didn't know what should be trigger
frame, couse UAPSD didn't work correctly in AP mode.
To configure UAPSD params correctly we have to
send them after peer assoc command.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Firmware has a feature to track if the associated STA is not acking the frames.
When that happens, the firmware sends WMI_PEER_STA_KICKOUT_EVENTID event to the
host. Enable that to faster detect when a STA has left BSS without sending a
deauth frame.
Also set huge keepalive timeouts to avoid using the keepalive functionality in
the firmware.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Enable ap_ps_peer_param_cmdid for 10.x FW.
This is used mainly for AP UAPSD.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Reduce the Rx count threshold to make sure we read
the available credits for Tx.
Signed-off-by: Julien Massot <jmassot@aldebaran-robotics.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
With the previous value (1700), some urb are dropped
with a babble error (urb status equal -EOVERFLOW).
These error seems to only happen when urb length is a
multiple of packet size (512).
Signed-off-by: Julien Massot <jmassot@aldebaran-robotics.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch will also change behavior of rx_beacons statistic.
Instead of collecting all received beacons, it will collect only
ours. This, IMO make more sense, since for troubleshooting we will
need to know count of our beacons, or both.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
this function is used by most ath driver, so it can be moved here.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This fixes bug found by the kbuild test robot:
tree: git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next.git master
head: 1e2f9295f4c657500111514f92a3d3894d0e05b4
commit: 1cbbcb08c786964a16773c39f2536f1923c73c58 [135/140] wil6210: prefetch head of packet
config: make ARCH=microblaze allyesconfig
All error/warnings:
drivers/net/wireless/ath/wil6210/txrx.c: In function 'wil_vring_reap_rx':
>> drivers/net/wireless/ath/wil6210/txrx.c:381:2: error: implicit declaration of function 'prefetch' [-Werror=implicit-function-declaration]
prefetch(skb->data);
^
cc1: some warnings being treated as errors
vim +/prefetch +381 drivers/net/wireless/ath/wil6210/txrx.c
375 wil_err(wil, "Rx size too large: %d bytes!\n", dmalen);
376 kfree_skb(skb);
377 return NULL;
378 }
379 skb_trim(skb, dmalen);
380
> 381 prefetch(skb->data);
382
383 wil_hex_dump_txrx("Rx ", DUMP_PREFIX_OFFSET, 16, 1,
384 skb->data, skb_headlen(skb), false);
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Prevent a possible overflow condition which results in occasional
bad IQ coefficients and EVM numbers.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch fixes a bug in the TX IQ calibration post
processing routine because of which the driver disables
TX IQ correction even though the calibration results
are valid. This fix is applicable for all chips in the
AR9003 family.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
debug_sta.c: ath_debug_rate_stats() error: buffer overflow 'rstats->ht_stats' 24 <= 24
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Global Transmission Timeout interrupts are generated by
the HW when transmission of a frame fails - this is done
based on the threshold programmed in the AR_GTXTO register.
Currently, even though the interrupt is enabled for all chips,
it is not handled in the driver. This patch handles GTT events
for AR9003 and above chips, checking if the MAC/BB has hung
after successive GTT interrupts crosses a threshold (5).
This can be enabled for the older chips in the AR9002 family once
appropriate HW hang checks are implemented for them.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
There is no need to do this and we can avoid
an unused variable warning when CONFIG_ATH9K_WOW is
not selected.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This would be useful when debugging RX performance issues.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Also, rename node_stat to node_aggr.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The REGULATORY_CUSTOM_REG can be used during early init with
the goal of overriding the wiphy's default regulatory settings
in case the alpha2 of the device is not known. In the case that
the alpha2 becomes known lets avoid having drivers having to
clear the REGULATORY_CUSTOM_REG flag by doing it for them
when regulatory_hint() is used.
Cc: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
ath wants to first apply the custom regd and only later
will it revert to not using it if an alpha2 regulatory
domain is found. Since the wireless core now enforces
usage of the REGULATORY_CUSTOM_REG strictly when
wiphy_apply_custom_regulatory() is used this makes
ath adhere to the expected behaviour but also updates
the wiphy after its done with the custom usage.
This fixes this warning:
[ 5.488733] ath: phy0: ASPM enabled: 0x43
[ 5.488735] ath: EEPROM regdomain: 0x0
[ 5.488736] ath: EEPROM indicates default country code should be used
[ 5.488736] ath: doing EEPROM country->regdmn map search
[ 5.488737] ath: country maps to regdmn code: 0x3a
[ 5.488737] ath: Country alpha2 being used: US
[ 5.488738] ath: Regpair used: 0x3a
[ 5.488738] ------------[ cut here ]------------
[ 5.488745] WARNING: CPU: 0 PID: 161 at
/home/sujith/dev/wireless-testing/net/wireless/reg.c:1361
wiphy_apply_custom_regulatory+0x17a/0x1b0 [cfg80211]()
[ 5.488746] wiphy should have REGULATORY_CUSTOM_REG
The wireless core can *later* lift this flag for us for when
using the regulatory_hint() to make this fix more generic.
Reported-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
|
|
|
|
Add set_bitrate_mask callback. Currently
ath10k HW is limited to handle only single
fixed rate setting or limit number of used
spatial streams.
Example:
iw wlanX set bitrates legacy-5 ht-mcs-5 vht-mcs-5 2:9
will setup VHT, nss=2, mcs=9
iw wlanX set bitrates legacy-5 18 ht-mcs-5 vht-mcs-5
will setup legacy, 18Mbps
iw wlanX set bitrates legacy-5 ht-mcs-5 3 vht-mcs-5
will setup HT, nss=1, mcs=3
iw wlanX set bitrate legacy-5 ht-mcs-5 vht-mcs-5 1:0-9
will setup nss=1
iw wlanX set bitrate legacy-5 ht-mcs-5 vht-mcs-5 1:0-9 2:0-9
will setup nss=2
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Firmware dbglogs can be now enabled through fw_dbglog file. To enable all
possible log messages run:
echo 0xffffffff > /sys/kernel/debug/ieee80211/phy0/ath10k/fw_dbglog
And to put back firmare defaults use 0x0:
echo 0x0 > /sys/kernel/debug/ieee80211/phy0/ath10k/fw_dbglog
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Send firmware WMI debug logs to user space for further processing.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Firmware can send simple ascii strings as debug messages using
WMI_DEBUG_PRINT_EVENTID, print those with ATH10K_DBG_WMI log level.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
To not exceed number of allowed clients (AP mode), make sure to
check how many of them are already on the peers list.
10.X firmware support up to 127 peers, non-AP centric firmwares 16.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Currently ath10k is not using STA KICKOUT firmware functionality.
In order to avoid unwanted WMI_PEER_STA_KICKOUT_EVENT event this functionality
should be disabled when not used.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Add Kconfig option that allow DFS functionality.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Fast Channel Change across bands was enabled for
AR9462 recently, but this is causing baseband issues.
Disable it until this feature is tested well. Also,
remove the feature bit for AR9565 since it is
a single-band card and doesn't support this feature.
Cc: stable@vger.kernel.org
Reported-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Accessing the current channel definition in mac80211
when processing RX packets is problematic because it
could have been updated when a scan is issued. Since a
channel change involves flushing the existing packets
in the RX queue before a chip-reset is done, they would
be processed using the wrong band/channel information.
To avoid this, use the current channel information
maintained in the driver.
Cc: stable@vger.kernel.org
Reported-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
* Add new AR9565 1.0/1.0.1/1.1 IDs
* Change Dell/Lenovo/Samsung cards to 2-Antenna with diversity.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
As soon as skb is ready to be reaped, prefetch 1-st cache line.
This accelerates data access that is performed later, during the
packet classification by the driver and IP stack.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Bit DMA_CFG_DESC_TX_OFFLOAD_CFG_L3T_IPV4_POS should be set for IPv4
only. Don't set it for IPv6
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Use hardware capabilities to limit IRQ generation to about 15 per msec
It corresponds to about 7 packets/IRQ when running iperf with default
parameters at 1.3Gbps
Do not enable this feature in the sniffer (monitor) mode, because
interrupt moderation cause timestamp accuracy deterioration.
For the sniffer flow, it is important to get precise timestamp.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This value is no longer used by mac80211, and practically no
driver ever set it to a correct value anyway, so remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
|
