aboutsummaryrefslogtreecommitdiff
path: root/drivers/net/wireless/ath/ath9k/ar9002_calib.c
AgeCommit message (Collapse)Author
2011-11-02ath9k_hw: Fix noise floor calibration timeout on fast channel changeRajkumar Manoharan
During the fast channel change noise floor values are being loaded twice at init_cal and after channel_change. The commit "ath9k_hw: Improve fast channel change for AR9003 chips" overlooked it that caused failure to load nf while doing bgscan. This patch performs noise floor calibration after the fast and full reset. Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-20Merge branch 'master' of git://git.infradead.org/users/linville/wirelessJohn W. Linville
Conflicts: drivers/net/wireless/iwlwifi/iwl-pci.c drivers/net/wireless/iwlwifi/iwl-trans-pcie-tx.c drivers/net/wireless/rt2x00/rt2800usb.c drivers/net/wireless/wl12xx/main.c
2011-09-19ath9k: load noise floor from history after the full chip resetRajkumar Manoharan
Currently during the full reset, the nf calibration is always restarted from the defaults. The noise floor history buffers are never be used again after the scan and ath reset. This patch ensures that nf histories are always be used that helps to improve the signal quality on congested environment Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-30ath9k_hw: fix calibration on 5 ghzFelix Fietkau
ADC calibrations cannot run on 5 GHz with fast clock enabled. They need to be disabled, otherwise they'll hang and IQ mismatch calibration will not be run either. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Reported-by: Adrian Chadd <adrian@freebsd.org> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-05-27ath9k: Fix AR9287 calibrationAdrian Chadd
The AR9287 calibration code was not being called because of an incorrect MAC revision check. This forced the AR9287 to use the AR9285 initial calibration code and bypass the AR9287 code entirely. Signed-off-by: Adrian Chadd <adrian@freebsd.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-05-19ath9k: Drag the driver to the year 2011Sujith Manoharan
The Times They Are a-Changin'. Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-03-30ath9k_hw: Fix throughput drops in HT40 mode for AR9287 chipsRajkumar Manoharan
Doing adc gain calibration for AR9287 chips is causing throughput drops in HT40 mode. Remove ADC Gain from supported calibration list. Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-27Merge branch 'master' of ↵David S. Miller
ssh://master.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6
2011-01-19ath9k_hw: fix carrier leakage calibration for AR9271Rajkumar Manoharan
AR9285 carrier leakage calibration related workaround on high temperature is not applicable for AR9271. Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-17ath9k_hw: do PA offset calibration only on longcal intervalRajkumar Manoharan
The power detector adc offset calibration has to be done on 4 minutes interval (longcal * pa_skip_count). But the commit "ath9k_hw: fix a noise floor calibration related race condition" makes the PA calibration executed more frequently beased on nfcal_pending value. Running PAOffset calibration lesser than longcal interval doesn't help anything and the worse part is that it causes NF load timeouts and RX deaf conditions. In a very noisy environment, where the distance b/w AP & station is ~10 meter and running a downlink udp traffic with frequent background scan causes "Timeout while waiting for nf to load: AR_PHY_AGC_CONTROL=0x40d1a" and moves the chip into deaf state. This issue was originaly reported in Android platform where the network-manager application does bgscan more frequently on AR9271 chips. (AR9285 family usb device). Cc: stable@kernel.org Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-10ath9k_hw: Fix calibration for AR9287 devicesSujith Manoharan
AR9287 based devices have issues with ADC gain calibration which would cause uplink throughput drops in HT40 mode. Remove ADC gain from the supported calibration algorithms. Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-07ath: Convert ath_print to ath_dbgJoe Perches
Remove ath/debug.h and the includes of these files. Coalesce long formats. Correct a few misspellings and missing "\n"s from these logging messages. Remove unnecessary trailing space before a newline. Remove ARRAY_SIZE casts, use printf type %zu Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-10-06ath9k_hw: clean up register write bufferingFelix Fietkau
Throughout the code, DISABLE_REGWRITE_BUFFER is always called right after REGWRITE_BUFFER_FLUSH. Since that's unlikely to change any time soon, that makes keeping those ops separate rather pointless, as it only increases code size and line number counts. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-10-06ath9k_hw: clean up calibration flagsFelix Fietkau
The calibration actual calibration flags are only used by the per chip family source files, so it makes more sense to define them in those files instead of globally. That way the code has to test for less flags. Also instead of using a separate callback for testing whether a particular calibration type is supported, simply adjust ah->supp_cals in the calibration init which is called right after the hardware reset, before any of the calibrations are run. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-10-05ath9k_hw: remove some useless calibration dataFelix Fietkau
The percal struct and bitmask for the initial DC calibration are not used anywhere, so they can be removed. Signed-off-by: Felix Fietkau <nbd@openwrt.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-09-27ath9k_hw: simplify revision checks for AR9287Felix Fietkau
Since AR9287 v1.0 was never sold (and the initvals removed), its revision checks can be simplified similar to AR9280 Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-09-27ath9k_hw: simplify revision checks for AR9285Felix Fietkau
Since AR9285 v1.0 and v1.1 were never sold (and the initvals removed), its revision checks can be simplified similar to AR9280 Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-09-27ath9k_hw: simplify revision checks for AR9280Felix Fietkau
Since AR9280 v1.0 was never sold (and the initvals removed), v1.0 specific revision checks can be removed and the 'v2.0 or later' check can be simplified to a check for AR9280 or later. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-04ath9k_hw: fix a noise floor calibration related race conditionFelix Fietkau
On AR5008-AR9002, other forms of calibration must not be started while the noise floor calibration is running, as this can create invalid readings which were sometimes not even recoverable by any further calibration attempts. This patch also ensures that the result of noise floor measurements are processed faster and also allows the result of the initial calibration on reset to make it into the NF history buffer Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-04ath9k_hw: clean up per-channel calibration dataFelix Fietkau
The noise floor history buffer is currently not kept per channel, which can lead to problems when changing channels from a clean channel to a noisy one. Also when switching from HT20 to HT40, the noise floor history buffer is full of measurements, but none of them contain data for the extension channel, which it needs quite a bit of time to recover from. This patch puts all the per-channel calibration data into a single data structure, and gives the the driver control over whether that is used per-channel or even not used for some channels. For ath9k_htc, I decided to keep this per-channel in order to avoid creating regressions. For ath9k, the data is kept only for the operating channel, which saves some space. ath9k_hw takes care of wiping old data when the operating channel or its channel flags change. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-04ath9k_hw: clean up and fix initial noise floor calibrationFelix Fietkau
On AR9003 the initial noise floor calibration is currently triggered at the end of the reset without allowing the hardware to update the baseband settings. This could potentially make scans in noisy environments a bit more unreliable, so use the same calibration sequence that is used on AR9002. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-07-12ath9k_hw: fix a sign error in the IQ calibration codeFelix Fietkau
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16ath9k_hw: Use buffered register writesSujith
This patch adds macros at certain places which could be optimized for multiple register writes. The performance of ath9k_htc improves considerably, especially reducing the latency involved in a scan run. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16ath9k_hw: fill in the callbacks for calibration for AR9003Luis R. Rodriguez
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-16ath9k_hw: split calib code by hardware familiesLuis R. Rodriguez
Calibration code touches phy registers and since these change the calibration code needs to be abstracted. Noise floor calibration is the only thing remaining but since the remaining calls only touch the AR_PHY_AGC_CONTROL register we'll just define that register conditionally, that will be done separately. The goal is to remove the dependency of ar9002_phy.h on calib.c This also adds stubs to be filled for AR9003 calibration code. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>