| Age | Commit message (Collapse) | Author |
|---|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
net/core/dev.c
|
|
As reported by Andrew Lutomirski <amluto@gmail.com>
All the intel wired ethernet drivers were calling netif_carrier_off
and netif_stop_queue (or variants) before calling register_netdevice
This is incorrect behavior as was pointed out by davem, and causes
ifconfig and friends to report a strange state before first link
after the driver was loaded, since without a netif_carrier_off, the stack
assumes carrier_on, but before register_netdev, netlink messages are not
sent out telling link state.
This apparently confused *some* versions of networkmanager.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reported-by: Andrew Lutomirski <amluto@gmail.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The thresholds for the DCB priority flow control are incorrect for 82599.
This fixes the thresholds to be correct.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The traffic classes in hardware are not symmetrical for Rx and Tx. Rx
is every 16 descriptor queues, Tx is not. It runs 32-32-16-16-8-8-8 when
running with 8 traffic classes, and runs 64-32-16 when running with 4
traffic classes. This patch fixes the mapping.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
|
|
GCC warns:
drivers/net/ixgbe/ixgbe_main.c: In function 'ixgbe_sfp_config_module_task':
drivers/net/ixgbe/ixgbe_main.c:3920: warning: suggest parantheses around
operand of '!' or change '&' to '&&' or '!' to '~'
Which I think is right. Bracket to remove ambiguity.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prevent ixgbe from putting the adapter into D3 during shutdown except when
we're going to power off the system, since doing that may generally cause
problems with kexec to happen (such problems were observed for igb and
forcedeth). For this purpose seperate ixgbe_shutdown() from ixgbe_suspend()
and use the appropriate PCI PM callbacks in both of them.
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the update of real_num_tx_queues from
ixgbe_acquire_msix_vectors() to ixgbe_set_num_queues(), to ensure it
be always in sync with num_tx_queues.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Don't do the num_tx_queues based masking on calculating tx queue
index.
1) num_tx_queues is not always power-of-2, because it also depends on
the online cpu numbers. So the masking could be a performance bug
on a 6 cpu system.
2) queue_mapping will be limited by real_num_tx_queues=num_tx_queues
in the generic netdev function set_cur_queue_map(). So the bound
limiting here is not necessary.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
GCC warns:
drivers/net/ixgbe/ixgbe_main.c: In function 'ixgbe_sfp_config_module_task':
drivers/net/ixgbe/ixgbe_main.c:3920: warning: suggest parantheses around
operand of '!' or change '&' to '&&' or '!' to '~'
Which I think is right. Bracket to remove ambiguity.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Not all physical connection types are being correctly identified. This
fixes that issue, and cleans up the logic to make it more maintainable.
Also clean up the code for device capabilities from the EEPROM to support
multiple SKUs of the same hardware.
Bump the version to reflect all the updates since the 82599 merge.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The orig_autoc variable tracks the original setting of the autonegotiate
state prior to trying a new speed. The usage is inconsistent and not very
maintainable. This patch updates the usage to make it more consistent.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch does two things:
1) On 82599, the PHY is emedded in the MAC. On 82598, the SFP+ NIC has an external PHY. The reset in the SFP+ setup patch for 82598 is unnecessary on 82599, and adds extra dead time to device initialization. This removes that PHY reset for 82599 only.
2) On 82599, the SFP+ modules are multispeed fiber modules (10G/1G). We need to make sure to identify them properly for the remaining init sections to properly set them up.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When PHY operations are determined, the PHY must be identified. This
identification causes bus access, and should be contained within its own
routines. This also helps the 82599 PHY init paths for both SFP+ and
KX/KX4 devices to be easier to maintain.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When flow control is disabled, an invalid low/high watermark configuration
should not matter.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
82599 supports 64 IVAR registers this patch adds a define to
allow us to access them.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These defines allow for definition of target pool for packets that
pass L2 filtering but didn't pass any of the pool filters. They are
needed to reset the default pool.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IXGBE_MTQC_64VF was wrong and 32VF not defined at all. This patch
corrects that.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The discard pause frames bit was not enabled, so flow control frames could
be passed up to the host. Enabled DPF to keep the frames off the stack.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All NICs were reporting WOL support when only the KX4 NIC is capable of
supporting WOL. This patch adds a function to check for and exclude all
non-WOL capable nics from enabling WOL in ethtool.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The LED blink code is common for 82599 as well. It should be moved to
ixgbe_common.c so both devices can use it, and not have it duplicated.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
ring parameters
While setting up the ring parameters using ethtool the driver can
panic or leak memory as ixgbe_open tries to setup tx & rx resources.
The updated logic will use ixgbe_down/up after successful allocation of
tx & rx resources
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We were basicly ignoring ethtool users request for FC autoneg
and replying to queries with a "best guess". This patch
enables the driver to store if we want to enable/disable
autoneg FC and do the correct behavior.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When network interface is made active we were not handling the error
scenarios properly to clean up rx & tx resources which might result in
a driver panic.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch resolves an issue with map single being used to map a buffer and
then unmap page being used to unmap it. In addition it handles any error
conditions that may be detected using skb_dma_map.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MSI-X allocation broke after the 82599 merge on systems with more than 8
CPU cores. 82598 drops back into MSI mode, which isn't sufficient to run
full, efficient 10G line rate.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the past flow control wasn't enabled by default under the
incorrect assumption that this opened up us to a denial of
service attack. However since any switch that forwarded flow
control would be extremely msiconfigured and/or buggy, this
concern no longer out weighs the preformance gains from
having FC enabled.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The priority flow control settings from the netlink layer aren't taking
effect in the base driver. The boolean pfc_mode_enable in the dcb_config
struct isn't being set, so the hardware configuration code is never
reached.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ethtool tries to get advertised speed from phy.autoneg_advertised.
However for copper media this wasn't happening until later do to
an other fix which moved mac.ops.setup_link_speed placement in
ixgbe_link_config(). This patch will display the default advertised
speeds if it can't yet get this information from phy.autoneg_advertised.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ixgbe driver had issues when DEBUG was defined because the hw_dbg macro
was incomplete. This patch completes the code based off of the code that
already existed in the igb module.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When changing DCB parameters, ixgbe needs to have the MAC reset. The way
the flow control code is setup today, PFC will be disabled on a reset.
This patch adds a new flow control type for PFC, and then has the netlink
layer take care of toggling which type of flow control to enable.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert ixgbe to use net_device_ops properly.
Rather than changing the select_queue function pointer
just check the flag.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The watchdog will schedule an interrupt to help make sure queues are
cleaned in the case when an interrupt is missed, most likely due to very
high load. On 82599, there are extra interrupt registers to account for
the larger number of MSI-X vectors (64 total for 82599 vs. 18 total for
82598). These must be taken into account when performing this operation in
the watchdog.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ethtool isn't reporting the support level of WoL for 82599 KX4 devices.
While the device does support WoL, ethtool was never updated to properly
report the level of support, nor will it allow ethtool to modify the type
of packets to listen for.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
82598's PCI bus reporting on driver load was broken after 82599 merged.
This results in incorrect reporting, and an erroneous warning message
that the 82598 is in a PCIe slot that isn't fast enough to run 10GbE.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
drivers/net/igb/igb_main.c
drivers/net/qlge/qlge_main.c
drivers/net/wireless/ath9k/ath9k.h
drivers/net/wireless/ath9k/core.h
drivers/net/wireless/ath9k/hw.c
|
|
Cleanup a bit of whitespace, add some function header comments, and fix a
few comments around the driver.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Tx DMA unit should be disabled when bringing the device down. Also,
the KX4 device with 82599 supports WoL, so we should clear the Wake Up
Status (WUS) after a PCIe slot reset.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are possible times that a driver may fail to completely initialize,
due to a buggy platform or a buggy kernel. In those cases, we'd rather
fail gracefully instead of a panic. Add a few safety checks to some
critical paths to try and prevent a panic in these corner-case situations.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This cleans up the following pieces of the Rx initialization path:
- Enable the ECC memory fault interrupt in OTHER causes.
- Fix an 82598 initialization of RDRXCTL when depending on RSS and VMDq to
be enabled. We don't need these features enabled to safely set the MVMEN
bit to allow multiple SRRCTL register mappings into the RXDCTL registers.
- Fix the RSS initialization path to not stomp on DCB accidentally. When
configuring the MRQC (multiple Rx queue contol) register, we want to make
sure we only OR in features as necessary, instead of full assignment.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Tx accounting when cleaning during NAPI was not completely properly.
We should use the work_limit to determine when to finish cleaning, and
use the same to return the cleaned status. The impact of running like this
causes the NAPI clean for this Tx to get stuck in a scheduling loop, and
can result in Tx not getting cleaned, ending with a Tx hang and device
reset.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Occasionally if the driver was loaded in a system that
didn't support MSI-X or MSI and was on a shared interrupt,
the driver would then panic in NAPI on the first shared
interrupt because we hadn't called napi_add yet.
Solution: call napi_add before calling request_irq
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The interrupt models using EITR have changed in 82599. The way the register
is laid out, the change is transparent to some of the existing code.
However, some of it isn't. This patch fixes all the cases where EITR
handling is different than 82598.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
82599 mistakenly enabled drop on Rx queues in the packet buffer. The
default mode should be store-and-forward from the FIFO.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The rx_no_dma_resources counter reported by ethtool -S ethX is not
counting correctly. In 82599, the queue mappings for the counters need
to be mapped properly, and accounted for properly.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A purely cosmetic change. Report which physical layer is present, instead
of PHY unknown. 82599 added new PHY types for the SFP+ devices, and this
was missed getting updated.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Multiple unicast address support appears to have been broken with the
change to support net_device_ops. This a regression from 2.6.28 to 2.6.29.
I'm not 100% on whether ndo_set_multicast_list can be NULL after this
or not. If ndo_set_rx_mode is set everything _should_ be using it.
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
'pap' is never used in ixgbe_dcb_hw_config_82599()
and 'eec' in ixgbe_acquire_eeptom() is only used when
status == 0 but GCC has some trouble seeing that.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
