| Age | Commit message (Collapse) | Author |
|---|
|
Converts the list and the core manipulating with it to be the same as uc_list.
+uses two functions for adding/removing mc address (normal and "global"
variant) instead of a function parameter.
+removes dev_mcast.c completely.
+exposes netdev_hw_addr_list_* macros along with __hw_addr_* functions for
manipulation with lists on a sandbox (used in bonding and 80211 drivers)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As an alternative to a quite large patch previously submitted by Joe
Perches to make use of kernel logging API, this patch is much less
intrusive.
Convert e_<level> to netdev_<level>
Use #define pr_fmt
Convert a few printks to pr_<level>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The recent PCI runtime PM patch broke build for CONFIG_PM_RUNTIME
and CONFIG_PM_SLEEP undefined. Fix that by moving the PM callbacks
under suitable #ifdefs.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the PCI runtime power management framework to add basic PCI
runtime PM support to the e1000e driver. Namely, make the driver
suspend the device when the link is off and set it up for generating
a wakeup event after the link has been detected again. [This
feature is disabled until the user space enables it with the help of
the /sys/devices/.../power/contol device attribute.]
Based on a patch from Matthew Garrett.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reported by Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
|
|
Found this problem when testing IPv6 from a KVM guest to a remote
host via e1000e device on the host.
The following patch fixes the check for IPv6 GSO packet in Intel
ethernet drivers to use skb_is_gso_v6(). SKB_GSO_DODGY is also set
when packets are forwarded from a guest.
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When testing the "e1000: enhance frame fragment detection" (and e1000e)
patches we found some bugs with reducing the MTU size. The 1024 byte
descriptor used with the 1000 mtu test also (re) introduced the
(originally) reported bug, and causes us to need the e1000_clean_tx_irq
"enhance frame fragment detection" fix.
So what has occured here is that 2.6.32 is only vulnerable for mtu <
1500 due to the jumbo specific routines in both e1000 and e1000e.
So, 2.6.32 needs the 2kB buffer len fix for those smaller MTUs, but
is not vulnerable to the original issue reported. It has been pointed
out that this vulnerability needs to be patched in older kernels that
don't have the e1000 jumbo routine. Without the jumbo routines, we
need the "enhance frame fragment detection" fix the e1000, old
e1000e is only vulnerable for < 1500 mtu, and needs a similar
fix. We split the patches up to provide easy backport paths.
There is only a slight bit of extra code when this fix and the
original "enhance frame fragment detection" fixes are applied, so
please apply both, even though it is a bit of overkill.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
|
|
Originally patched by Neil Horman <nhorman@tuxdriver.com>
e1000e could with a jumbo frame enabled interface, and packet split disabled,
receive a packet that would overflow a single rx buffer. While in practice
very hard to craft a packet that could abuse this, it is possible.
this is related to CVE-2009-4538
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The variable count and i are unsigned so the (<|>=)0 tests do not work.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make updating the multicast address list generic for all families and
enforce the requirement to update the entire multicast table array all at
once instead of piecemeal which causes problems on some parts.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Similar to 82571/2/3 parts that already do this, if ESB2/80003es2lan parts
have an alternate MAC address provided in the EEPROM use it instead of the
default MAC address. This patch makes the the actual code that does this
generic so that it can be better used by both MAC families.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
drivers/net/benet/be_cmds.h
include/linux/sysctl.h
|
|
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Due to a change in pci_restore_state()[1] which clears the saved_state
flag, the driver should call pci_save_state() to set the flag once again
to avoid issues with EEH (same fix that recently was submitted for ixgbe).
[1] commmit 4b77b0a2ba27d64f58f16d8d4d48d8319dda36ff
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use DEFINE_PCI_DEVICE_TABLE() so we get place PCI ids table into correct section
in every case.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Bit 7 in the CTRL_REG register is actually the Software Definable Pin 3,
not the Software Definable Pin 7.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only files where David Miller is the primary git-signer.
wireless, wimax, ixgbe, etc are not modified.
Compile tested x86 allyesconfig only
Not all files compiled (not x86 compatible)
Added a few > 80 column lines, which I ignored.
Existing checkpatch complaints ignored.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In testing we have found that skb_dma_map/unmap is incompatible with HW
IOMMU due to the fact that multiple mappings will return different results.
In order to correct this we need to remove skb_dma_map/unmap calls from the
e1000e driver.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This new PCI device ID is for a new combination of MAC and PHY both of
which already have supporting code in the driver, just not yet in this
combination. During validation of the device, an intermittent issue was
discovered with waking it from a suspended state which can be resolved with
the pre-existing workaround to disable gigabit speed prior to suspending.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The different families (80003es2lan, 8257x, ICHx/PCH) supported by the
driver each have their own conditions when the PHY can be powered down.
This patch rewrites the PHY power up/down code to fit with the family-
specific style used in the driver. All pre-existing calls to power up or
down the PHY remain untouched. A new call to power down the PHY when
removing the driver when the interface is down replaces the current call
to reset the PHY in order to reduce power consumption.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The two MAC-families that have VLAN filter table register arrays manage
each a bit differently from one another, so provide family-specific
functions for managing the register arrays and function pointers to access
the appropriate function. Also make sure attempts to access these
register arrays are not done on parts not supporting that feature.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
drivers/ieee802154/fakehard.c
drivers/net/e1000e/ich8lan.c
drivers/net/e1000e/phy.c
drivers/net/netxen/netxen_nic_init.c
drivers/net/wireless/ath/ath9k/main.c
|
|
The Tx unit hang detection code in e1000e detects other hangs caused by
hardware components (e.g. Rx, DMA units), but it is not possible to detect
exactly which component is hung so it has always assumed a Tx unit hang.
When dumping a message to the system log because of a hang, this patch adds
more data to help narrow the cause of the issue and makes the message
non-Tx-specific. Because this new code reads PHY registers which can
sleep, move it off to a workqueue. This and all previously existing work
tasks in the driver are now cancelled when the driver is removed.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It was pointed out a pm_qos DMA latency requirement set when the driver is
loaded when parts that support early receive of jumbo frames are probed
could have that requirement overidden if another part supported by the
driver (one that does not support early receive of jumbo frames) is probed
later. Change the DMA latency requirement to be per-interface if needed
instead of per driver.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The phy and nvm operations structures have function pointers that contain
"phy" and "nvm" in the pointer names which are redundant since the
structures are already obviously in phy and nvm structures.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch depends on a previous one that cleans up redundant #includes.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver was only updating MII stats when an LSC up was detected and
the interface had not already been reported up to netdev. This meant
MII stats returned in response to an SIOCGMIIREG ioctl would always
show a link up if it had ever been up. This was misleading the networking
daemon guessnet, which uses this ioctl, into making improper network port
selections.
This fix adds a call to e1000_phy_read_status() to actively read the
mii stats before responding to the SIOCGMIIREG ioctl.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When using legacy interrupts, do not clean the Rx ring while resetting
otherwise traffic will not pass.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Clearing the interrupt timers following an IMS clear has the unwanted
side-effect of flushing all descriptors immediately following a partial
write when interrupts are disabled.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When changing MTU, save it off prior to resetting otherwise the flow control
thresholds may be miscalculated.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On some devices (e.g. 82578) not having a Tx timeout factor when linked at
100Mbps can cause false reports of hardware hangs on busy hubs.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 3ec2a2b80f3eb53851fe4cef9e65b5d33376ef89 broke Tx/Rx when using
jumbo frames on certain parts (i.e. only PAUSE frames could be exchanged
once the high water mark was reached preventing normal packet traffic).
This patch reverts the breakage and sets appropriate high and low water
marks of the Rx FIFO for 82577/82578 which require a workaround due to a
flow control issue in hardware.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Not as fancy as coccinelle. Checkpatch errors ignored.
Compile tested allyesconfig x86, not all files compiled.
grep -rPl --include=*.[ch] "\brequest_irq\s*\([^,\)]+,\s*\&" drivers/net | while read file ; do \
perl -i -e 'local $/; while (<>) { s@(\brequest_irq\s*\([^,\)]+,\s*)\&@\1@g ; print ; }' $file ;\
done
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since net_device has an instance of net_device_stats,
we can remove the instance of this from the private adapter structure.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The only error returned by pci_{en,dis}able_pcie_error_reporting() is
-EIO which simply means that Advanced Error Reporting is not supported.
There is no need to report that, so remove the error check from e1000e,
igb and ixgbe.
Signed-off-by: Frans Pop <elendil@planet.nl>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dev_ioctl() already checks capable(CAP_NET_ADMIN) before calling the
driver's implementation of MDIO ioctls.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
drivers/net/yellowfin.c
|
|
Get rid of some bogus return wrapping as well.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit 111b9dc5 ("e1000e: add aer support") introduces pcie aer
support for e1000e, but it is not reasonable to disable it in
e1000_remove but enable it in e1000_resume. This patch enables aer
support in e1000_probe.
Signed-off-by: Xiaotian Feng <dfeng@redhat.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With manageability (Intel AMT) enabled via BIOS, PHY wakeup does not get
configured on newer parts which use PHY wakeup vs. MAC wakeup which causes
WoL to not work. The driver should configure PHY wakeup whether or not
manageability is enabled.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
on permanent failure
PCI drivers that implement the io_error_detected callback
should return PCI_ERS_RESULT_DISCONNECT if the state
passed in is pci_channel_io_perm_failure. This state is not
checked in many of the network drivers.
This patch fixes the omission in the e1000e driver.
Signed-off-by: Mike Mason <mmlnx@us.ibm.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The last hunk of this commit:
commit 12d04a3c12b420f23398b4d650127642469a60a6
Author: Alexander Duyck <alexander.h.duyck@intel.com>
Date: Wed Mar 25 22:05:03 2009 +0000
e1000e: commonize tx cleanup routine to match e1000 & igb
changed the logic for determining if we should call napi_complete or
not at then end of a napi poll.
If the NIC is using MSI-X with no work to do in ->poll, net_rx_action
can just spin indefinitely on older kernels and for 2 jiffies on newer
kernels since napi_complete is never called and budget isn't
decremented.
Discovered and verified while testing driver backport to an older
kernel.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
e1000e_config_collision_dist() sets tctl, but subsequently tctl is
overwritten. It seems to me that as things stand the call to
e1000e_config_collision_dist() has no effect and should either be
removed or moved down a little bit. This kernel patch takes the latter
option.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
