| Age | Commit message (Collapse) | Author |
|---|
|
Pull mtd update from David Woodhouse:
- More robust parsing especially of xattr data in JFFS2
- Updates to mxc_nand and gpmi drivers to support new boards and device tree
- Improve consistency of information about ECC strength in NAND devices
- Clean up partition handling of plat_nand
- Support NAND drivers without dedicated access to OOB area
- BCH hardware ECC support for OMAP
- Other fixes and cleanups, and a few new device IDs
Fixed trivial conflict in drivers/mtd/nand/gpmi-nand/gpmi-nand.c due to
added include files next to each other.
* tag 'for-linus-3.5-20120601' of git://git.infradead.org/linux-mtd: (75 commits)
mtd: mxc_nand: move ecc strengh setup before nand_scan_tail
mtd: block2mtd: fix recursive call of mtd_writev
mtd: gpmi-nand: define ecc.strength
mtd: of_parts: fix breakage in Kconfig
mtd: nand: fix scan_read_raw_oob
mtd: docg3 fix in-middle of blocks reads
mtd: cfi_cmdset_0002: Slight cleanup of fixup messages
mtd: add fixup for S29NS512P NOR flash.
jffs2: allow to complete xattr integrity check on first GC scan
jffs2: allow to discriminate between recoverable and non-recoverable errors
mtd: nand: omap: add support for hardware BCH ecc
ARM: OMAP3: gpmc: add BCH ecc api and modes
mtd: nand: check the return code of 'read_oob/read_oob_raw'
mtd: nand: remove 'sndcmd' parameter of 'read_oob/read_oob_raw'
mtd: m25p80: Add support for Winbond W25Q80BW
jffs2: get rid of jffs2_sync_super
jffs2: remove unnecessary GC pass on sync
jffs2: remove unnecessary GC pass on umount
jffs2: remove lock_super
mtd: gpmi: add gpmi support for mx6q
...
|
|
Since commit 6a918bade9dab40aaef80559bd1169c69e8d69cb, the mxc_nand driver
fails with:
Driver must set ecc.strength when using hardware ECC
This is because nand_scan_tail checks for correct ecc strength
settings, so we must set them up before nand_scan_tail.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: stable@vger.kernel.org [3.4+]
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
The 'mtd_writev' interface calls the function assigned
to the '_write' field of a given mtd device if that is
not NULL. The block2mtd driver sets the '_writev' field
to the 'mtd_writev' function itself and thus causes a
endless loop.
This is caused by 1dbebd32562b3c2caeca35960e5cb00bfcc12900
(mtd: harmonize mtd_writev usage).
Remove the assignment from the block2mtd driver to fix the
issue.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: stable@kernel.org [3.3+]
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Fix an issue which was introduced by the recent addition of ecc.strength.
The ecc.strength wasn't set in gpmi-nand, resulting in the following crash:
[ 2.550000] kernel BUG at drivers/mtd/nand/nand_base.c:3347!
...
[ 2.550000] [<c020841c>] (nand_scan_tail+0x328/0x650) from [<c02f68e0>] (gpmi_nand_probe+0x43c/0x5a4)
[ 2.550000] [<c02f68e0>] (gpmi_nand_probe+0x43c/0x5a4) from [<c01f6618>] (platform_drv_probe+0x14/0x18)
[ 2.550000] [<c01f6618>] (platform_drv_probe+0x14/0x18) from [<c01f55b0>] (driver_probe_device+0x74/0x1fc)
[ 2.550000] [<c01f55b0>] (driver_probe_device+0x74/0x1fc) from [<c01f57cc>] (__driver_attach+0x94/0x98)
[ 2.550000] [<c01f57cc>] (__driver_attach+0x94/0x98) from [<c01f3d40>] (bus_for_each_dev+0x50/0x80)
[ 2.550000] [<c01f3d40>] (bus_for_each_dev+0x50/0x80) from [<c01f4e18>] (bus_add_driver+0x188/0x25c)
[ 2.550000] [<c01f4e18>] (bus_add_driver+0x188/0x25c) from [<c01f5a70>] (driver_register+0x78/0x138)
[ 2.550000] [<c01f5a70>] (driver_register+0x78/0x138) from [<c043dc7c>] (gpmi_nand_init+0xc/0x30)
[ 2.550000] [<c043dc7c>] (gpmi_nand_init+0xc/0x30) from [<c0008824>] (do_one_initcall+0x108/0x17c)
[ 2.550000] [<c0008824>] (do_one_initcall+0x108/0x17c) from [<c042a8b8>] (kernel_init+0xfc/0x1bc)
[ 2.550000] [<c042a8b8>] (kernel_init+0xfc/0x1bc) from [<c000fab4>] (kernel_thread_exit+0x0/0x8)
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
MTD_OF_PARTS and the default setting is not working due to using 'Y'
instead of 'y', introduced in commit
d6137badeff1ef64b4e0092ec249ebdeaeb3ff37. This made our board, and
possibly other boards using DTS defined partitions and not having
CONFIG_MTD_OF_PARTS=y defined in the defconfig, fail to mount root.
Signed-off-by: Frank Svendsboe <frank.svendsboe@gmail.com>
Cc: stable@kernel.org [3.2+]
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Pull MIPS updates from Ralf Baechle:
"The whole series has been sitting in -next for quite a while with no
complaints. The last change to the series was before the weekend the
removal of an SPI patch which Grant - even though previously acked by
himself - appeared to raise objections. So I removed it until the
situation is clarified. Other than that all the patches have the acks
from their respective maintainers, all MIPS and x86 defconfigs are
building fine and I'm not aware of any problems introduced by this
series.
Among the key features for this patch series is a sizable patchset for
Lantiq which among other things introduces support for Lantiq's
flagship product, the FALCON SOC. It also means that the opensource
developers behind this patchset have overtaken Lantiq's competing
inhouse development team that was working behind closed doors.
Less noteworthy the ath79 patchset which adds support for a few more
chip variants, cleanups and fixes. Finally the usual dose of tweaking
of generic code."
Fix up trivial conflicts in arch/mips/lantiq/xway/gpio_{ebu,stp}.c where
printk spelling fixes clashed with file move and eventual removal of the
printk.
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (81 commits)
MIPS: lantiq: remove orphaned code
MIPS: Remove all -Wall and almost all -Werror usage from arch/mips.
MIPS: lantiq: implement support for FALCON soc
MTD: MIPS: lantiq: verify that the NOR interface is available on falcon soc
MTD: MIPS: lantiq: implement OF support
watchdog: MIPS: lantiq: implement OF support and minor fixes
SERIAL: MIPS: lantiq: implement OF support
GPIO: MIPS: lantiq: convert gpio-stp-xway to OF
GPIO: MIPS: lantiq: convert gpio-mm-lantiq to OF and of_mm_gpio
GPIO: MIPS: lantiq: move gpio-stp and gpio-ebu to the subsystem folder
MIPS: pci: convert lantiq driver to OF
MIPS: lantiq: convert dma to platform driver
MIPS: lantiq: implement support for clkdev api
MIPS: lantiq: drop ltq_gpio_request() and gpio_to_irq()
OF: MIPS: lantiq: implement irq_domain support
OF: MIPS: lantiq: implement OF support
MIPS: lantiq: drop mips_machine support
OF: PCI: const usage needed by MIPS
MIPS: Cavium: Remove smp_reserve_lock.
MIPS: Move cache setup to setup_arch().
...
|
|
It seems there is a bug in scan_read_raw_oob() in nand_bbt.c which
should cause wrong functioning of NAND_BBT_SCANALLPAGES option.
Artem: the patch did not apply and I had to amend it a bit.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: stable@kernel.org
|
|
Corner case reads do not work, and return false data and
ECC. This case is typically seen in a ubifs usage, with a
read of type:
- docg3 docg3: doc_read_oob(from=14882415, mode=1,
data=(c30eca40:12), oob=( (null):0))
This results in the following reads:
- docg3 docg3: doc_read_data_area(buf= (null), len=111)
- docg3 docg3: doc_read_data_area(buf=c30eca40, len=12)
- docg3 docg3: doc_read_data_area(buf= (null), len=389)
- docg3 docg3: doc_read_data_area(buf= (null), len=0)
- docg3 docg3: doc_read_data_area(buf= (null), len=16)
If we suppose that the pages content is :
- bytes 0 .. 111 : 0x0a
- bytes 112 .. 255 : 0x0f
Then the returned bytes will be :
- 111 times 0x0a (correct)
- 0x0a 2 times and 0x0f 10 times (incorrect, should be
0x0a,0x0f)
- 0x0f 389 times (correct)
- nothing
- correct OOB
The reason seams that the first 111 bytes read ends between
the 2 docg3 planes, and that the first following read (in
the 12 bytes sequence, read of 16 bit word) returns the byte
of the rightmost plane duplicated in high and lower byte of
the word.
Fix this behaviour by ensuring that if the previous read
ended up in-between the 2 planes, there will be a first 1
byte read to get back to the beginning of leftmost plane.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
Pull arm-soc clock driver changes from Olof Johansson:
"The new clock subsystem was merged in linux-3.4 without any users,
this now moves the first three platforms over to it: imx, mxs and
spear.
The series also contains the changes for the clock subsystem itself,
since Mike preferred to have it together with the platforms that
require these changes, in order to avoid interdependencies and
conflicts."
Fix up trivial conflicts in arch/arm/mach-kirkwood/common.c (code
removed in one branch, added OF support in another) and
drivers/dma/imx-sdma.c (independent changes next to each other).
* tag 'clock' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (97 commits)
clk: Fix CLK_SET_RATE_GATE flag validation in clk_set_rate().
clk: Provide dummy clk_unregister()
SPEAr: Update defconfigs
SPEAr: Add SMI NOR partition info in dts files
SPEAr: Switch to common clock framework
SPEAr: Call clk_prepare() before calling clk_enable
SPEAr: clk: Add General Purpose Timer Synthesizer clock
SPEAr: clk: Add Fractional Synthesizer clock
SPEAr: clk: Add Auxiliary Synthesizer clock
SPEAr: clk: Add VCO-PLL Synthesizer clock
SPEAr: Add DT bindings for SPEAr's timer
ARM i.MX: remove now unused clock files
ARM: i.MX6: implement clocks using common clock framework
ARM i.MX35: implement clocks using common clock framework
ARM i.MX5: implement clocks using common clock framework
ARM: Kirkwood: Replace clock gating
ARM: Orion: Audio: Add clk/clkdev support
ARM: Orion: PCIE: Add support for clk
ARM: Orion: XOR: Add support for clk
ARM: Orion: CESA: Add support for clk
...
|
|
Pull UBI and UBIFS updates from Artem Bityutskiy:
UBIFS:
* Always support xattrs (remove the Kconfig option)
* Always support debugging (remove the Kconfig option)
* A fix for a memory leak on error path
* A number of clean-ups
UBI:
* Always support debugging (remove the Kconfig option)
* Remove "data type" hint support
* Huge amount of renames to prepare for the fastmap wor
* A lot of clean-ups
* tag 'upstream-3.5-rc1' of git://git.infradead.org/linux-ubifs: (54 commits)
UBI: modify ubi_wl_flush function to clear work queue for a lnum
UBI: introduce UBI_ALL constant
UBI: add lnum and vol_id to struct ubi_work
UBI: add volume id struct ubi_ainf_peb
UBI: add in hex the value for UBI_INTERNAL_VOL_START to comment
UBI: rename scan.c to attach.c
UBI: remove scan.h
UBI: rename UBI_SCAN_UNKNOWN_EC
UBI: move and rename attach_by_scanning
UBI: rename _init_scan functions
UBI: amend comments after all the renamings
UBI: rename ubi_scan_leb_slab
UBI: rename ubi_scan_move_to_list
UBI: rename ubi_scan_destroy_ai
UBI: rename ubi_scan_get_free_peb
UBI: rename ubi_scan_rm_volume
UBI: rename ubi_scan_find_av
UBI: rename ubi_scan_add_used
UBI: remove unused function
UBI: make ubi_scan_erase_peb static and rename
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial updates from Jiri Kosina:
"As usual, it's mostly typo fixes, redundant code elimination and some
documentation updates."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (57 commits)
edac, mips: don't change code that has been removed in edac/mips tree
xtensa: Change mail addresses of Hannes Weiner and Oskar Schirmer
lib: Change mail address of Oskar Schirmer
net: Change mail address of Oskar Schirmer
arm/m68k: Change mail address of Sebastian Hess
i2c: Change mail address of Oskar Schirmer
net: Fix tcp_build_and_update_options comment in struct tcp_sock
atomic64_32.h: fix parameter naming mismatch
Kconfig: replace "--- help ---" with "---help---"
c2port: fix bogus Kconfig "default no"
edac: Fix spelling errors.
qla1280: Remove redundant NULL check before release_firmware() call
remoteproc: remove redundant NULL check before release_firmware()
qla2xxx: Remove redundant NULL check before release_firmware() call.
aic94xx: Get rid of redundant NULL check before release_firmware() call
tehuti: delete redundant NULL check before release_firmware()
qlogic: get rid of a redundant test for NULL before call to release_firmware()
bna: remove redundant NULL test before release_firmware()
tg3: remove redundant NULL test before release_firmware() call
typhoon: get rid of redundant conditional before all to release_firmware()
...
|
|
Pull arm-soc board specific changes from Olof Johansson:
"While we generally attempt to get rid of board specific files and
replace them with device tree based descriptions, a lot of platforms
have not come that far:
In shmobile, we add two new board files because their recently started
effort to add DT support has not proceeded enough to use it for all of
the important hardware.
In Kirkwood, we are adding support for new boards with a combination
of DT and board file contents in multiple cases.
pxa/mmp and imx are extending support for existing board files but not
adding new ones."
Fix up trivial conflicts in arch/arm/mach-{mmp/ttc_dkb.c,shmobile/{Kconfig,Makefile}}
* tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (94 commits)
ARM: shmobile: fix smp build
ARM: kirkwood: Add support for RaidSonic IB-NAS6210/6220 using devicetree
kirkwood: Add iconnect support
orion/kirkwood: create a generic function for gpio led blinking
kirkwood/orion: fix orion_gpio_set_blink
ARM: kirkwood: Define DNS-320/DNS-325 NAND in fdt
kirkwood: Allow nand to be configured via. devicetree
mtd: Add orion_nand devicetree bindings
ARM: kirkwood: Basic support for DNS-320 and DNS-325
ARM: mach-shmobile: Use DT_MACHINE for armadillo 800 eva
ARM: mach-shmobile: Use DT_MACHINE for KZM9G
ARM: pxa: hx4700: Add Synaptics NavPoint touchpad
ARM: pxa: Use REGULATOR_SUPPLY macro
ARM: mach-shmobile: kzm9g: enable SMP boot
ARM: mach-shmobile: kzm9g: defconfig update
ARM: mach-shmobile: kzm9g: add PCF8757 gpio-key
ARM: mach-shmobile: kzm9g: add SDHI support
ARM: mach-shmobile: kzm9g: add MMCIF support
ARM: mach-shmobile: kzm9g: correct screen direction
ARM: mach-shmobile: sh73a0.h: add GPIO_NR
...
|
|
Pull arm soc-specific pinctrl changes from Olof Johansson:
"With this, five platforms are moving to the relatively new pinctrl
subsystem for their pin management, replacing the older soc specific
in-kernel interfaces with common code.
There is quite a bit of net addition of code for each platform being
added to the pinctrl subsystem. But the payback comes later when
adding new boards can be done by only providing new device trees
instead."
Fix up trivial conflicts in arch/arm/mach-ux500/{Makefile,board-mop500.c}
* tag 'pinctrl' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (61 commits)
mtd: nand: gpmi: fix compile error caused by pinctrl call
ARM: PRIMA2: select PINCTRL and PINCTRL_SIRF in Kconfig
ARM: nomadik: enable PINCTRL_NOMADIK where needed
ARM: mxs: enable pinctrl support
video: mxsfb: adopt pinctrl support
ASoC: mxs-saif: adopt pinctrl support
i2c: mxs: adopt pinctrl support
mtd: nand: gpmi: adopt pinctrl support
mmc: mxs-mmc: adopt pinctrl support
serial: mxs-auart: adopt pinctrl support
serial: amba-pl011: adopt pinctrl support
spi/imx: adopt pinctrl support
i2c: imx: adopt pinctrl support
can: flexcan: adopt pinctrl support
net: fec: adopt pinctrl support
ARM: ux500: switch MSP to using pinctrl for pins
ARM: ux500: alter MSP registration to return a device pointer
ARM: ux500: switch to using pinctrl for uart0
ARM: ux500: delete custom pin control system
ARM: ux500: switch over to Nomadik pinctrl driver
...
|
|
Pull first batch of arm-soc cleanups from Olof Johansson:
"These cleanups are basically all over the place. The idea is to
collect changes with minimal impact but large number of changes so we
can avoid them from distracting in the diffstat in the other series.
A significant number of lines get removed here, in particular because
the ixp2000 and ixp23xx platforms get removed. These have never been
extremely popular and have fallen into disuse over time with no active
maintainer taking care of them. The u5500 soc never made it into a
product, so we are removing it from the ux500 platform.
Many good cleanups also went into the at91 and omap platforms, as has
been the case for a number of releases."
Trivial modify-delete conflicts in arch/arm/mach-{ixp2000,ixp23xx}
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (152 commits)
ARM: clps711x: Cleanup IRQ handling
ARM clps711x: Removed unused header mach/time.h
ARM: clps711x: Added note about support EP731x CPU to Kconfig
ARM: clps711x: Added missing register definitions
ARM: clps711x: Used own subarch directory for store header file
Dove: Fix Section mismatch warnings
ARM: orion5x: ts78xx debugging changes
ARM: orion5x: remove PM dependency from ts78xx
ARM: orion5x: ts78xx fix NAND resource off by one
ARM: orion5x: ts78xx whitespace cleanups
Orion5x: Fix Section mismatch warnings
Orion5x: Fix warning: struct pci_dev declared inside paramter list
ARM: clps711x: Combine header files into one for clps711x-targets
ARM: S3C24XX: Use common macro to define resources on mach-qt2410.c
ARM: S3C24XX: Use common macro to define resources on mach-osiris.c
ARM: EXYNOS: Adapt to cpuidle core time keeping and irq enable
ARM: S5PV210: Use common macro to define resources on mach-smdkv210.c
ARM: S5PV210: Use common macro to define resources on dev-audio.c
ARM: S5PC100: Use common macro to define resources on dev-audio.c
ARM: S5P64X0: Use common macro to define resources on dev-audio.c
...
|
|
When running on a FALC-ON SoC, we need to check the bootstrap options to see
if NOR is available.
Signed-off-by: John Crispin <blogic@openwrt.org>
Acked-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: linux-mtd@lists.infradead.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3815/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Adds bindings for OF and make use of module_platform_driver for lantiq
based socs.
Signed-off-by: John Crispin <blogic@openwrt.org>
Acked-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: linux-mtd@lists.infradead.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3811/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
This patch modifies ubi_wl_flush to force the erasure of
particular volume id / logical eraseblock number pairs. Previous functionality
is preserved when passing UBI_ALL for both values. The locations where ubi_wl_flush
were called are appropriately changed: ubi_leb_erase only flushes for the
erased LEB, and ubi_create_volume forces only flushing for its volume id.
External code can call this new feature via the new function ubi_flush() added
to kapi.c, which simply passes through to ubi_wl_flush().
This was tested by disabling the call to do_work in ubi thread, which results
in the work queue remaining unless explicitly called to remove. UBIFS was
changed to call ubifs_leb_change 50 times for four different LEBs. Then the
new function was called to clear the queue: passing wrong volume ids / lnum,
correct ones, and finally UBI_ALL for both to ensure it was finally all
cleard. The work queue was dumped each time and the selective removal
of the particular LEB numbers was observed. Extra checks were enabled and
ubifs's integck was also run. Finally, the drive was repeatedly filled and
emptied to ensure that the queue was cleared normally.
Artem: amended the patch.
Signed-off-by: Joel Reardon <reardonj@inf.ethz.ch>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
Joel will use it in his 'ubi_flush()' extention to specify all eraseblocks.
Also amend the comment for UBI_UNKNOWN - it is used beyond attaching info
structure now.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
This is part of a multipart patch to allow UBI to force the erasure of
particular logical eraseblock numbers. In this patch, the volume id and LEB
number are added to ubi_work data structure, and both are also passed as a
parameter to schedule erase to set it appropriately. Whenever ubi_wl_put_peb
is called, the lnum is also passed to be forwarded to schedule erase. Later,
a new ubi_sync_lnum will be added to execute immediately all work related to
that lnum.
This was tested by outputting the vol_id and lnum during the schedule of
erasure. The ubi thread was disabled and two ubifs drives on separate
partitions repeated changed a small number of LEBs. The ubi module was readded,
and all the erased LEBs, corresponding to the volumes, were added to the
schedule erase queue.
Artem: minor tweaks
Signed-off-by: Joel Reardon <reardonj@inf.ethz.ch>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
This patch adds the volume id to struct ubi_ainf_peb when scanning the LEBs at
startup. PEBs now added to the erase queue will know their original LEB number
and volume id, if available, and will be -1 otherwise (for instance, if the VID
header is unreadable).
This was tested by creating an ubi device with 3 volumes and disabiling the
ubi_thread's do_work functionality. The different ubi volumes were formatted
to ubifs and had files created and erased. The ubi modules was reloaded and
the list of LEB's added to the erased list was outputted, confirming the
volume ids and LEB numbers were appropriate.
Signed-off-by: Joel Reardon <reardonj@inf.ethz.ch>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
Explicitly provide the first internal volume ID value in the comment for
UBI_INTERNAL_VOL_START. This allows developers who, when adding features
related to volume ids and observe unexpected very large volume ids, to grep
for the observed value in the source code and find out immediately that it is
expected behaviour.
Signed-off-by: Joel Reardon <reardonj@inf.ethz.ch>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
Finally, rename the scan.c file. Now adding fastmap support won't look that
hacky anymore.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
This file is small and it does not make sense to have it separate from where
everything else lives, so merge it with ubi.h.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
Rename the constant to UBI_UNKNOWN, for the same reason that we are going
to add nother attaching method and re-use the same data structures, so the
"SCAN" in the name becomes incorrect. I've also removed the "_EC" part because
Joel is going to use this constant for other fields in the attaching info data
structures.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
Rename the 'attach_by_scanning()' function to 'ubi_attach()' and move it to
scan.c. Richard will plug his fastmap stuff there.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
We have a couple of initialization funcntionsn left which have "_scan" suffic -
rename them:
ubi_eba_init_scan() -> ubi_eba_init()
ubi_wl_init_scan() -> ubi_wl_init()
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
This patch amends commentaries in scan.[ch] to match the new logic. Reminder -
we did the restructuring to prepare the code for adding the fastmap. This patch
also renames a couple of functions - it was too difficult to separate out that
change and I decided that it is not too bad to have it in the same patch with
commentaries changes.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
The old name is not logical anymore - rename it to 'aeb_slab_cache'.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
The old name is not logical anymore - rename it to 'ubi_move_aeb_to_list()'.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
The old name is not logical anymore - rename it to 'ubi_destroy_ai()'.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
The old name is not logical anymore - rename it to 'ubi_early_get_peb()'.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
The old name is not logical anymore - rename it to 'ubi_remove_av()'.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
The old name is not logical anymore - rename it to 'ubi_find_av()'.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
The old name is not logical anymore - rename it to 'ubi_add_to_av()'.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
The 'ubi_scan_find_aeb()' function is unused and thus can be removed.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
The 'ubi_scan_erase_peb()' is used only in scan.c so can be static. Also
re-name it to 'early_erase_peb()' because we tend to use "ubi_" prefix only for
non-static fuction and also because the new name is better.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
After re-naming the 'struct ubi_scan_volume' we should adjust all variables
named 'sv' to something else, because 'sv' stands for "scanning volume".
Let's rename it to 'av' which stands for "attaching volume" which is
a bit more consistent and has the same length, which makes re-naming easy.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
|
|
After re-naming the 'struct ubi_scan_info' we should adjust all variables
named 'si' to something else, because 'si' stands for "scanning info".
Let's rename it to 'ai' which stands for "attaching info" which is
a bit more consistent and has the same length, which makes re-naming easy.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
|
|
After re-naming the 'struct ubi_scan_leb' we should adjust all variables
named 'seb' to something else, because 'seb' stands for "scanning eraseblock".
Let's rename it to 'aeb' which stands for "attaching eraseblock" which is
a bit more consistend and has the same length.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
|
|
Now some commentaries are out-of-date, after we re-named the data
structures - amend them.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
|
|
Rename 'struct ubi_scan_info' to 'struct ubi_attach_info'. This is part
of the code re-structuring I am trying to do in order to add fastmap
in a more logical way. Fastmap can share a lot with scanning, including
the attach-time data structures, which all now have "scan" word in the
name. Let's get rid of this word.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
|
|
Rename 'struct ubi_scan_volume' to 'struct ubi_ainf_volume'. This is part
of the code re-structuring I am trying to do in order to add fastmap
in a more logical way. Fastmap can share a lot with scanning, including
the attach-time data structures, which all now have "scan" word in the
name. Let's get rid of this word and use "ainf" instead which stands
for "attach information". It has the same length as "scan" so re-naming
is trivial.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
|
|
Rename 'struct ubi_scan_leb' to 'struct ubi_ainf_leb'. This is part
of the code re-structuring I am trying to do in order to add fastmap
in a more logical way. Fastmap can share a lot with scanning, including
the attach-time data structures, which all now have "scan" word in the
name. Let's get rid of this word and use "ainf" instead which stands
for "attach information". It has the same length as "scan" so re-naming
is trivial.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
|
|
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
This patch removes the 'dbg_err()' macro and we now use 'ubi_err' instead.
The idea of 'dbg_err()' was to compile out some error message to make the
binary a bit smaller - but I think it was a bad idea.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
We have the "sefl-check" feature in UBI, but for historical reasons many
corresponding functions and commentaries in the code use term "paranoid check"
instead. Let's clean this up and use "self-check" everywhere.
This patch renames functions, amends messages and kills several redundant
debugging messages.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
We have the "sefl-check" feature in UBI, but for historical reasons many
corresponding functions and commentaries in the code use term "paranoid check"
instead. Let's clean this up and use "self-check" everywhere.
This patch renames functions, amends comments and messages. It touches only the
io.c file.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
This patch kills the UBI debugging Kconfig option completely and makes all the
debugging stuff to be always compiled-in. It was pain in the neck to maintain
this useless option because all users I am aware of have debugging enabled
anyway - how else will you diagnose errors otherwise?
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
I am going to remove the "UBI debugging" compilation option and make the
debugging stuff to be always compiled it. This patch is a preparation
which renames 'ubi_dbg_dump_mkvol_req()' to 'ubi_dump_mkvol_req()'.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
I am going to remove the "UBI debugging" compilation option and make the
debugging stuff to be always compiled it. This patch is a preparation
which renames 'ubi_dbg_dump_seb()' to 'ubi_dump_seb()'.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
