| Age | Commit message (Collapse) | Author |
|---|
|
When SDIO runtime PM was originally introduced, we immediately faced
two regressions with two different chipsets, and in response decided
not to enable it by default.
With the recent work on the 8686 we hoped we found all the gotchas,
so 08da834 did make sense (at least experimentally).
Unfortunately we now see that some setups out there still refuse to
work when SDIO runtime PM is enabled by default (see
http://www.spinics.net/lists/linux-mmc/msg11161.html), and obviously
we can't live with these kind of regressions.
This reverts commit 08da834a24312157f512224691ad1fddd11c1073.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Daniel Drake <dsd@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
These two basic defines were everywhere, simply because module.h
was also everywhere. But we are cleaning up the latter. So make
the exporters actually call out their need for the include.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Now that we have improved the runtime power management powerup/powerdown
code, we believe that MMC_CAP_POWER_OFF_CARD is no longer necessary:
runtime PM should now work everywhere.
The only hard evidence for introducing MMC_CAP_POWER_OFF_CARD was the
Marvell sd8686 wifi chip, which was believed to require external gpio
manipulation which wasn't supported by some boards.
After further investigation it was realized (and confirmed by Marvell
folks) that sd8686 requirements can be fulfilled by changing the reset
sequence itself, even if no external gpio is manipulated.
For further information, see the following thread:
http://www.mail-archive.com/linux-mmc@vger.kernel.org/msg04289.html
Enable this trivially for a release or two. If no problems are reported,
we will follow up with a more extensive patch to remove this flag
altogether. If problems are reported, we can look at whitelist/blacklist
possibilities as before.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The default multithread workqueue can cause the same work to be executed
concurrently on a different CPUs. This isn't really suitable for clock
gating as it might already gated the clock and gating it twice results both
host->clk_old and host->ios.clock to be set to 0.
To prevent this from happening we use system_nrt_wq instead.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Chris Ball <cjb@laptop.org>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
As per suggestion by Linus Walleij:
> If you think the names of the functions are confusing then
> you may rename them, say like this:
>
> mmc_host_clk_ungate() -> mmc_host_clk_hold()
> mmc_host_clk_gate() -> mmc_host_clk_release()
>
> Which would make the usecases more clear
(This is CC'd to stable@ because the next two patches, which fix
observable races, depend on it.)
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (75 commits)
mmc: core: eMMC bus width may not work on all platforms
mmc: sdhci: Auto-CMD23 fixes.
mmc: sdhci: Auto-CMD23 support.
mmc: core: Block CMD23 support for UHS104/SDXC cards.
mmc: sdhci: Implement MMC_CAP_CMD23 for SDHCI.
mmc: core: Use CMD23 for multiblock transfers when we can.
mmc: quirks: Add/remove quirks conditional support.
mmc: Add new VUB300 USB-to-SD/SDIO/MMC driver
mmc: sdhci-pxa: Add quirks for DMA/ADMA to match h/w
mmc: core: duplicated trial with same freq in mmc_rescan_try_freq()
mmc: core: add support for eMMC Dual Data Rate
mmc: core: eMMC signal voltage does not use CMD11
mmc: sdhci-pxa: add platform code for UHS signaling
mmc: sdhci: add hooks for setting UHS in platform specific code
mmc: core: clear MMC_PM_KEEP_POWER flag on resume
mmc: dw_mmc: fixed wrong regulator_enable in suspend/resume
mmc: sdhi: allow powering down controller with no card inserted
mmc: tmio: runtime suspend the controller, where possible
mmc: sdhi: support up to 3 interrupt sources
mmc: sdhi: print physical base address and clock rate
...
|
|
led_trigger_register_simple() allocates memory which must not be leaked
in the error-path of mmc_add_host. Move it past the only error-check in
the function.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
instances"
This reverts commit 26fc8775b51484d8c0a671198639c6d5ae60533e, which has
been reported to cause boot/resume-time crashes for some users:
https://bbs.archlinux.org/viewtopic.php?id=118751.
Signed-off-by: Chris Ball <cjb@laptop.org>
Cc: <stable@kernel.org>
|
|
Currently there is a race in the MMC core between a card-detect
rescan work and the clock-gating work, scheduled from a command
completion. Fix it by removing the dedicated clock-gating mutex
and using the MMC standard locking mechanism instead.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Simon Horman <horms@verge.net.au>
Cc: Magnus Damm <damm@opensource.se>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Some sdio card are not following sdio standard, and do not work
when the sdio bus's clock is gated.
To keep functionnality for all legacy driver, we turn this quirk on
for every sdio card.
Drivers needs to disable the quirk manually when someone verifies that
their supported card works with clock gating.
Signed-off-by: Pierre Tardy <tardyp@gmail.com>
Acked-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Since we make sure the clock is enabled in the mmc_host_clk_exit()
function we should expect a reference counter of 1, not 0.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Tested-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
This patch modifies the MMC core code to optionally call the set_ios()
operation on the driver with the clock frequency set to 0 (gate) after
a grace period of at least 8 MCLK cycles, then restore it (ungate)
before any new request. This gives the driver the option to shut down
the MCI clock to the MMC/SD card when the clock frequency is 0, i.e.
the core has stated that the MCI clock does not need to be generated.
It is inspired by existing clock gating code found in the OMAP and
Atmel drivers and brings this up to the host abstraction. Gating is
performed before and after any MMC request.
This patchset implements this for the MMCI/PL180 MMC/SD host controller,
but it should be simple to switch OMAP/Atmel over to using this instead.
mmc_set_{gated,ungated}() add variable protection to the state holders
for the clock gating code. This is particularly important when ordinary
.set_ios() calls would race with the .set_ios() call resulting from a
delayed gate operation.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Reviewed-by: Chris Ball <cjb@laptop.org>
Tested-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
We have deprecated the distinction between hardware and physical
segments in the block layer. Consolidate the two limits into one in
drivers/mmc/.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
This fixes a build breakage introduced by commit 4c2ef25fe0b8 ("mmc: fix
all hangs related to mmc/sd card insert/removal during suspend/resume")
Cc: David Brownell <david-b@pacbell.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: linux-mmc@vger.kernel.org
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Maxim Levitsky <maximlevitsky@gmail.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If you don't use CONFIG_MMC_UNSAFE_RESUME, as soon as you attempt to
suspend, the card will be removed, therefore this patch doesn't change the
behavior of this option.
However the removal will be done by pm notifier, which runs while
userspace is still not frozen and thus can freely use del_gendisk, without
the risk of deadlock which would happen otherwise.
Card detect workqueue is now disabled while userspace is frozen, Therefore
if you do use CONFIG_MMC_UNSAFE_RESUME, and remove the card during
suspend, the removal will be detected as soon as userspace is unfrozen,
again at the moment it is safe to call del_gendisk.
Tested with and without CONFIG_MMC_UNSAFE_RESUME with suspend and hibernate.
[akpm@linux-foundation.org: clean up function prototype]
[akpm@linux-foundation.org: fix CONFIG_PM-n linkage, small cleanups]
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
implicit slab.h inclusion from percpu.h
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
|
|
MMC hosts that support power saving can use the 'enable' and 'disable'
methods to exit and enter power saving states. An explanation of their
use is provided in the comments added to include/linux/mmc/host.h.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Denis Karpov <ext-denis.2.karpov@nokia.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Philip Langdale <philipl@overt.org>
Cc: "Madhusudhan" <madhu.cr@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-Off-By: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
When CONFIG_DEBUG_FS is set, create a few files under /sys/kernel/debug
containing information about an mmc host's internal state. Currently,
just a single file is created, "ios", which contains information about
the current operating parameters for the bus (clock speed, bus width,
etc.)
Host drivers can add additional files and directories under the host's
root directory by passing the debugfs_root field in struct mmc_host as
the 'parent' parameter to debugfs_create_*.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Reorganise code so that mmc_hostname() works directly after allocation.
That way host drivers can use that name for resource allocations and
messages during probing.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
We register a simple trigger so make sure we use the corresponding
unregister function.
(Also means we get a dummy function when triggers aren't compiled in)
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Add a led trigger for each host controller that indicates if there
is a request active on the controller.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Signed-off-by: Nicolas Pitre <npitre@mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
drivers/mmc/core/host.c | 3509 -> 3457 (-52 bytes)
drivers/mmc/core/host.o | 92400 -> 92136 (-264 bytes)
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Make sure the kerneldoc comments are up to date and relevant.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Move basic host class device handling to its own file for clarity.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
