| Age | Commit message (Collapse) | Author |
|---|
|
commit 3f8349e6e98ba0455437724589072523865eae5e upstream.
TWL6030 family of PMIC use a shadow interrupt status register
while kernel processes the current interrupt event.
However, any write(0 or 1) to register INT_STS_A, INT_STS_B or
INT_STS_C clears all 3 interrupt status registers.
Since clear of the interrupt is done on 32k clk, depending on I2C
bus speed, we could in-adverently clear the status of a interrupt
status pending on shadow register in the current implementation.
This is due to the fact that multi-byte i2c write operation into
three seperate status register could result in multiple load
and clear of status and result in lost interrupts.
Instead, doing a single byte write to INT_STS_A register with 0x0
will clear all three interrupt status registers without the related
risk.
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The charger fault IRQs from the twl will in future patches be handled
by a seperate IRQ handler in the charger driver than the general charger
IRQ. Give them different IRQ numbers now to allow the charger driver to
be merged in the future.
Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
|
|
Converted with coccinelle.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
irq_desc checking in the interrupt demux routine is totally
pointless. The driver sets those lines up, so that cant go away
magically.
Remove the open coded handler magic and use the proper accessor.
This driver needs to be converted to threaded interrupts and buslock.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Signed-off-by: Lennert Buytenhek <buytenh@secretlab.ca>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
With TWL6030-usb, VBUS SESS_VLD and SESS_END events are not generated
as expected. When these interrupts are enabled, charger VBUS detection
interrupt does not get generated. So USBOTG has to be dependent on charger
VBUS interrupts.
So added one bit for USBOTG and changed the handler to call the
USBOTG handler whenever there is a charger VBUS interrpt.
VBUS SESS_VLD and SESS_END event generation issue is under debug with
HW team. This fix might not be required once after fixing the issue.
Signed-off-by: Balaji TK <balajitk@ti.com>
Signed-off-by: Hema HK <hemahk@ti.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Fixes following sparse warnings for twl4030 and twl6030 irq files.
drivers/mfd/twl4030-irq.c:783:5: warning: symbol 'twl4030_init_irq' was not
declared. Should it be static?
drivers/mfd/twl4030-irq.c:863:5: warning: symbol 'twl4030_exit_irq' was not
declared. Should it be static?
drivers/mfd/twl4030-irq.c:873:5: warning: symbol 'twl4030_init_chip_irq' was
not declared. Should it be static?
drivers/mfd/twl6030-irq.c:226:5: warning: symbol 'twl6030_init_irq' was not
declared. Should it be static?
drivers/mfd/twl6030-irq.c:290:5: warning: symbol 'twl6030_exit_irq' was not
declared. Should it be static?
Signed-off-by: G, Manjunath Kondaiah <manjugk@ti.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Tony Lindgren <tony@atomide.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Adding card detect callback function and card detect configuration
function for MMC1 Controller on OMAP4.
Card detect configuration function does initial configuration of the
MMC Control & PullUp-PullDown registers of Phoenix.
For MMC1 Controller, card detect interrupt source is
twl6030 which is non-gpio. The card detect call back function provides
card present/absent status by reading MMC Control register present
on twl6030.
Since OMAP4 doesn't use any GPIO line as used in OMAP3 for card detect,
the suspend/resume initialization which was done in omap_hsmmc_gpio_init
previously is moved to the probe thus making it generic for both OMAP3 &
OMAP4.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This patch adds support for phoenix interrupt framework. New iInterrupt
status register A, B, C are introduced in Phoenix and are cleared on write.
Due to the differences in interrupt handling with respect to TWL4030,
twl6030-irq.c is created for TWL6030 PMIC
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
