| Age | Commit message (Collapse) | Author |
|---|
|
commit 9aca4fb0571ce9cfef680ceb08d19dd008015307 upstream.
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/dvb-frontends/stv0367.c:791:1: warning: 'stv0367_writeregs.constprop.4' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer. Considering that I2C
transfers are generally limited, and that devices used on USB has a
max data length of 64 bytes for the control URBs.
So, it seem safe to use 64 bytes as the hard limit for all those devices.
On most cases, the limit is a way lower than that, but this limit
is small enough to not affect the Kernel stack, and it is a no brain
limit, as using smaller ones would require to either carefully each
driver or to take a look on each datasheet.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f7a35df15b1f7de7823946aebc9164854e66ea07 upstream.
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/dvb-frontends/stv090x.c:750:1: warning: 'stv090x_write_regs.constprop.6' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer. Considering that I2C
transfers are generally limited, and that devices used on USB has a
max data length of 64 bytes for the control URBs.
So, it seem safe to use 64 bytes as the hard limit for all those devices.
On most cases, the limit is a way lower than that, but this limit
is small enough to not affect the Kernel stack, and it is a no brain
limit, as using smaller ones would require to either carefully each
driver or to take a look on each datasheet.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f1baab870f6e93b668af7b34d6f6ba49f1b0e982 upstream.
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/tuners/e4000.c:50:1: warning: 'e4000_wr_regs' uses dynamic stack allocation [enabled by default]
drivers/media/tuners/e4000.c:83:1: warning: 'e4000_rd_regs' uses dynamic stack allocation [enabled by default]
drivers/media/tuners/fc2580.c:66:1: warning: 'fc2580_wr_regs.constprop.1' uses dynamic stack allocation [enabled by default]
drivers/media/tuners/fc2580.c:98:1: warning: 'fc2580_rd_regs.constprop.0' uses dynamic stack allocation [enabled by default]
drivers/media/tuners/tda18212.c:57:1: warning: 'tda18212_wr_regs' uses dynamic stack allocation [enabled by default]
drivers/media/tuners/tda18212.c:90:1: warning: 'tda18212_rd_regs.constprop.0' uses dynamic stack allocation [enabled by default]
drivers/media/tuners/tda18218.c:60:1: warning: 'tda18218_wr_regs' uses dynamic stack allocation [enabled by default]
drivers/media/tuners/tda18218.c:92:1: warning: 'tda18218_rd_regs.constprop.0' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer. Considering that I2C
transfers are generally limited, and that devices used on USB has a
max data length of 64 bytes for the control URBs.
So, it seem safe to use 64 bytes as the hard limit for all those devices.
On most cases, the limit is a way lower than that, but this limit
is small enough to not affect the Kernel stack, and it is a no brain
limit, as using smaller ones would require to either carefully each
driver or to take a look on each datasheet.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 56ac033725ec93a45170caf3979eb2b1211a59a8 upstream.
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/tuners/tuner-xc2028.c:651:1: warning: 'load_firmware' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer.
In the specific case of this driver, the maximum limit is 80, used only
on tm6000 driver. This limit is due to the size of the USB control URBs.
Ok, it would be theoretically possible to use a bigger size on PCI
devices, but the firmware load time is already good enough. Anyway,
if some usage requires more, it is just a matter of also increasing
the buffer size at load_firmware().
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 24e9a47e14f0a97ee97abc3dd86b2ef254448a17 upstream.
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/v4l2-core/v4l2-async.c:238:1: warning: 'v4l2_async_notifier_unregister' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer.
In this specific case, there's a hard limit imposed by V4L2_MAX_SUBDEVS,
with is currently 128. That means that the buffer size can be up to
128x8 = 1024 bytes (on a 64bits kernel), with is too big for stack.
Worse than that, someone could increase it and cause real troubles.
So, let's use dynamically allocated data, instead.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1d212cf0c2d89adf3d0a6d62d729076f49f087dc upstream.
drivers/media/pci/cx18/cx18-driver.c: In function 'cx18_read_eeprom':
drivers/media/pci/cx18/cx18-driver.c:357:1: warning: the frame size of 1072 bytes is larger than 1024 bytes [-Wframe-larger-than=]
That happens because the routine allocates 256 bytes for an eeprom buffer, plus
the size of struct i2c_client, with is big.
Change the logic to dynamically allocate/deallocate space for struct i2c_client,
instead of using the stack.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 278ba83a3a1932805be726bdd7dfb3156286d33a upstream.
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/pci/cx23885/cimax2.c:149:1: warning: 'netup_write_i2c' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer. Considering that I2C
transfers are generally limited, and that devices used on USB has a
max data length of 64 bytes for the control URBs.
So, it seem safe to use 64 bytes as the hard limit for all those devices.
On most cases, the limit is a way lower than that, but this limit
is small enough to not affect the Kernel stack, and it is a no brain
limit, as using smaller ones would require to either carefully each
driver or to take a look on each datasheet.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5bf30b3bc4ff80ef71a733a1f459cca4fa507892 upstream.
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/pci/ttpci/av7110_hw.c:510:1: warning: 'av7110_fw_cmd' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer.
In the specific case of this driver, the maximum fw command size
is 6 + 2, as checked using:
$ git grep -A1 av7110_fw_cmd drivers/media/pci/ttpci/
So, use 8 for the buffer size.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 64f7ef8afbf89f3c72c4d2472e4914ca198c0668 upstream.
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/usb/dvb-usb/cxusb.c:209:1: warning: 'cxusb_i2c_xfer' uses dynamic stack allocation [enabled by default]
drivers/media/usb/dvb-usb/cxusb.c:69:1: warning: 'cxusb_ctrl_msg' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer to be the max size of
a control URB payload data (64 bytes).
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1d7fa359d4c0fbb2756fa01cc47212908d90b7b0 upstream.
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/usb/dvb-usb/dibusb-common.c:124:1: warning: 'dibusb_i2c_msg' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer to be the max size of
a control URB payload data (64 bytes).
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0065a79a8698a953e4b201c5fce8db8940530578 upstream.
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/usb/dvb-usb/dw2102.c:368:1: warning: 'dw2102_earda_i2c_transfer' uses dynamic stack allocation [enabled by default]
drivers/media/usb/dvb-usb/dw2102.c:449:1: warning: 'dw2104_i2c_transfer' uses dynamic stack allocation [enabled by default]
drivers/media/usb/dvb-usb/dw2102.c:512:1: warning: 'dw3101_i2c_transfer' uses dynamic stack allocation [enabled by default]
drivers/media/usb/dvb-usb/dw2102.c:621:1: warning: 's6x0_i2c_transfer' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer to be the max size of
a control URB payload data (64 bytes).
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 65e2f1cb3fe0f0630834b9517ba8f631936f325c upstream.
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/usb/dvb-usb-v2/af9015.c:433:1: warning: 'af9015_eeprom_hash' uses dynamic stack allocation [enabled by default]
In this specific case, it is a gcc bug, as the size is a const, but
it is easy to just change it from const to a #define, getting rid of
the gcc warning.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7760e148350bf6df95662bc0db3734e9d991cb03 upstream.
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/usb/dvb-usb-v2/af9035.c:142:1: warning: 'af9035_wr_regs' uses dynamic stack allocation [enabled by default]
drivers/media/usb/dvb-usb-v2/af9035.c:305:1: warning: 'af9035_i2c_master_xfer' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer to be the max size of
a control URB payload data (64 bytes).
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c98300a0e8cf160aaea60bc05d2cd156a7666173 upstream.
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/usb/dvb-usb-v2/mxl111sf.c:74:1: warning: 'mxl111sf_ctrl_msg' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer to be the max size of
a control URB payload data (64 bytes).
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
pm_qos_remove_request was not called on video_release, resulting in the PM
core's list of requests being corrupted when the file handle was freed.
This has no immediate symptoms, but later in operation, the kernel will
panic as the PM core dereferences a dangling pointer.
Signed-off-by: Simon Farnsworth <simon.farnsworth@onelan.co.uk>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Fix to return -ENOMEM in the new i2c client and create workqueue error
handling case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
This patch fixes regression introduced in commit 5c77879ff9ab9e7
"[media] v4l2-dev: add new VFL_DIR_ defines" caused by not initializing
the vfl_dir field of the vfd_decoder instance of struct video_device,
after the field was introduced. It precluded calling the driver's ioctls
which require vfl_dir not to be equal to VFL_DIR_RX which is defined as
0 and uninitialized vfl_dir field is interpreted as such. In effect the
test in the v4l_s_fmt function failed for the ioctls that expect is_tx
to be false, which prevented the ioctl callbacks registered by the driver
from being called.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
userptr mode
Earlier version of dma-contig allocator in user ptr mode assumed that in
all cases DMA address equals physical address. This was just a special case.
Commit e15dab752d4c588544ccabdbe020a7cc092e23c8 introduced correct support
for converting userpage to dma address, but unfortunately it broke the
support for simple dma address = physical address for the case, when given
physical frame has no struct page associated with it (this happens if one
use for example dma_declare_coherent api or other reserved memory approach).
This commit restores support for such cases.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
[s.nawrocki@samsung.com: replaced #elsif with #elif]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Modify the bytesused/data_offset check to not fail if both bytesused
and data_offset is set to 0. This should minimize possible issues in
existing applications which worked before we enforced the plane lengths
for output buffers checks introduced in commit 8023ed09cb278004a2
"videobuf2-core: Verify planes lengths for output buffers"
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Smatch complains about the locking here because we mix spin_lock_irq()
with spin_lock_irqsave() in an unusual way. According to Smatch, it's
not always clear if the IRQs are enabled or disabled when we return. It
turns out this function is always called with IRQs enabled and we can
just use spin_lock_irq().
It's called from __enqueue_in_driver().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
The "i < " part of the "i < ARRAY_SIZE()" condition was missing.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
[g.liakhovetski@gmx.de: remove unrelated superfluous braces]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Reading firmware status register to detect whether firmware is
running or not didn't worked 100% reliably. That register was
likely set by firmware itself which means it could not contain
reasonable values until firmware is up and running. Usually it
just worked as some garbage value was returned accidentally but it
appears that in some cases returned garbage value was 0x00 which
was considered "firmware is up and running" by the driver and
firmware loading was skipped leaving device to non-working state.
Fix problem by removing unreliable check and let the driver keep
count whether firmware is loaded or not.
Signed-off-by: Andreas Matthies <a.matthies@gmx.net>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
The owner knows the system as "LX INFINITI Powerlite".
DMI information for this system:
System Information
Manufacturer: HCL Infosystems Limited
Product Name: T12Rg-H
Version: 1.0
Serial Number: B073A1189988
UUID: 326B3F00-001D-602F-CFD2-4E45435F4349
Wake-up Type: Power Switch
SKU Number:
Family:
Handle 0x0002, DMI type 2, 15 bytes
Base Board Information
Manufacturer: HCL Infosystems Limited
Product Name: T12Rg-H
Version: 1.0
Serial Number: BSN12345678901234567
Asset Tag: ATN12345678901234567
Features:
Board is a hosting board
Board is replaceable
Location In Chassis:
Chassis Handle: 0x0003
Type: Motherboard
Contained Object Handles: 0
Bus 001 Device 003: ID 05e1:0501 Syntek Semiconductor Co., Ltd DC-1125 Webcam
Signed-off-by: Gregor Jasny <gjasny@googlemail.com>
Reported-by: Noopur Srivastava <noopur.018@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Fix long-lasting bug that causes tuning failure of some frequencies
on 32-bit arch.
Special thanks goes to Damien CABROL who finally find root of the bug.
Also big thanks to Jacek Konieczny for donating "non-working" device.
[crope@iki.fi: fix trivial merge conflict]
[m.chehab@samsung.com: add missing header file]
Reported-by: Jacek Konieczny <jajcus@jajcus.net>
Reported-by: Torsten Seyffarth <t.seyffarth@gmx.de>
Reported-by: Jan Taegert <jantaegert@gmx.net>
Reported-by: Damien CABROL <cabrol.damien@free.fr>
Tested-by: Damien CABROL <cabrol.damien@free.fr>
Tested-by: Jan Taegert <jantaegert@gmx.net>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
The camera doesn't implement GET_DEF on the video probe control and
can crash when it receives the request depending on timings. Set the
PROBE_DEF quirk to work around the problem.
Reported-by: Jürgen Liebmann <info@pirna-esw6.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
BugLink: http://bugs.launchpad.net/bugs/1217957
Add quirk for Dell SP2008WFP monitor: 05a9:2641
Signed-off-by: Joseph Salisbury <joseph.salisbury@canonical.com>
Tested-by: Christopher Townsend <christopher.townsend@canonical.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
After the last architecture switched to generic hard irqs the config
options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code
for !CONFIG_GENERIC_HARDIRQS can be removed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull powerpc updates from Ben Herrenschmidt:
"Here's the powerpc batch for this merge window. Some of the
highlights are:
- A bunch of endian fixes ! We don't have full LE support yet in that
release but this contains a lot of fixes all over arch/powerpc to
use the proper accessors, call the firmware with the right endian
mode, etc...
- A few updates to our "powernv" platform (non-virtualized, the one
to run KVM on), among other, support for bridging the P8 LPC bus
for UARTs, support and some EEH fixes.
- Some mpc51xx clock API cleanups in preparation for a clock API
overhaul
- A pile of cleanups of our old math emulation code, including better
support for using it to emulate optional FP instructions on
embedded chips that otherwise have a HW FPU.
- Some infrastructure in selftest, for powerpc now, but could be
generalized, initially used by some tests for our perf instruction
counting code.
- A pile of fixes for hotplug on pseries (that was seriously
bitrotting)
- The usual slew of freescale embedded updates, new boards, 64-bit
hiberation support, e6500 core PMU support, etc..."
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (146 commits)
powerpc: Correct FSCR bit definitions
powerpc/xmon: Fix printing of set of CPUs in xmon
powerpc/pseries: Move lparcfg.c to platforms/pseries
powerpc/powernv: Return secondary CPUs to firmware on kexec
powerpc/btext: Fix CONFIG_PPC_EARLY_DEBUG_BOOTX on ppc32
powerpc: Cleanup handling of the DSCR bit in the FSCR register
powerpc/pseries: Child nodes are not detached by dlpar_detach_node
powerpc/pseries: Add mising of_node_put in delete_dt_node
powerpc/pseries: Make dlpar_configure_connector parent node aware
powerpc/pseries: Do all node initialization in dlpar_parse_cc_node
powerpc/pseries: Fix parsing of initial node path in update_dt_node
powerpc/pseries: Pack update_props_workarea to map correctly to rtas buffer header
powerpc/pseries: Fix over writing of rtas return code in update_dt_node
powerpc/pseries: Fix creation of loop in device node property list
powerpc: Skip emulating & leave interrupts off for kernel program checks
powerpc: Add more exception trampolines for hypervisor exceptions
powerpc: Fix location and rename exception trampolines
powerpc: Add more trap names to xmon
powerpc/pseries: Add a warning in the case of cross-cpu VPA registration
powerpc: Update the 00-Index in Documentation/powerpc
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial tree from Jiri Kosina:
"The usual trivial updates all over the tree -- mostly typo fixes and
documentation updates"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (52 commits)
doc: Documentation/cputopology.txt fix typo
treewide: Convert retrun typos to return
Fix comment typo for init_cma_reserved_pageblock
Documentation/trace: Correcting and extending tracepoint documentation
mm/hotplug: fix a typo in Documentation/memory-hotplug.txt
power: Documentation: Update s2ram link
doc: fix a typo in Documentation/00-INDEX
Documentation/printk-formats.txt: No casts needed for u64/s64
doc: Fix typo "is is" in Documentations
treewide: Fix printks with 0x%#
zram: doc fixes
Documentation/kmemcheck: update kmemcheck documentation
doc: documentation/hwspinlock.txt fix typo
PM / Hibernate: add section for resume options
doc: filesystems : Fix typo in Documentations/filesystems
scsi/megaraid fixed several typos in comments
ppc: init_32: Fix error typo "CONFIG_START_KERNEL"
treewide: Add __GFP_NOWARN to k.alloc calls with v.alloc fallbacks
page_isolation: Fix a comment typo in test_pages_isolated()
doc: fix a typo about irq affinity
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
"This series contains:
- Exynos s5p-mfc driver got support for VP8 encoder
- Some SoC drivers gained support for asynchronous registration
(needed for DT)
- The RC subsystem gained support for RC activity LED;
- New drivers added: a video decoder(adv7842), a video encoder
(adv7511), a new GSPCA driver (stk1135) and support for Renesas
R-Car (vsp1)
- the first SDR kernel driver: mirics msi3101. Due to some troubles
with the driver, and because the API is still under discussion, it
will be merged at staging for 3.12. Need to rework on it
- usual new boards additions, fixes, cleanups and driver
improvements"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (242 commits)
[media] cx88: Fix regression: CX88_AUDIO_WM8775 can't be 0
[media] exynos4-is: Fix entity unregistration on error path
[media] exynos-gsc: Register v4l2 device
[media] exynos4-is: Fix fimc-lite bayer formats
[media] em28xx: fix assignment of the eeprom data
[media] hdpvr: fix iteration over uninitialized lists in hdpvr_probe()
[media] usbtv: Throw corrupted frames away
[media] usbtv: Fix deinterlacing
[media] v4l2: added missing mutex.h include to v4l2-ctrls.h
[media] DocBook: upgrade media_api DocBook version to 4.2
[media] ml86v7667: fix compile warning: 'ret' set but not used
[media] s5p-g2d: Fix registration failure
[media] media: coda: Fix DT driver data pointer for i.MX27
[media] s5p-mfc: Fix input/output format reporting
[media] v4l: vsp1: Fix mutex double lock at streamon time
[media] v4l: vsp1: Add support for RT clock
[media] v4l: vsp1: Initialize media device bus_info field
[media] davinci: vpif_capture: fix error return code in vpif_probe()
[media] davinci: vpif_display: fix error return code in vpif_probe()
[media] MAINTAINERS: add entries for adv7511 and adv7842
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"Highlights:
- OF and ACPI helpers are now included in the core, and not in
external files anymore. This removes dependency problems for
modules and is cleaner, in general.
- mv64xxx-driver gains fifo usage to support mv78230
- imx-driver overhaul to support VF610
- various cleanups, most notably related to devm_* and CONFIG_PM
usage
- driver bugfixes and smaller feature additions"
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (51 commits)
i2c: rcar: add rcar-H2 support
i2c: sirf: retry 3 times as sometimes we get random noack and timeout
i2c: sirf: support reverse direction of address
i2c: sirf: fix the typo for setting bitrate to less than 100k
i2c: sirf: we need to wait I2C_RESET status in resume
i2c: sirf: reset i2c controller early after we get a noack
i2c: designware: get SDA hold time, HCNT and LCNT configuration from ACPI
i2c: designware: make HCNT/LCNT values configurable
i2c: mpc: cleanup clock API use
i2c: pnx: fix error return code in i2c_pnx_probe()
i2c: ismt: add error return code in probe()
i2c: mv64xxx: fix typo in binding documentation
i2c: imx: use exact SoC revision to document binding
i2c: move ACPI helpers into the core
i2c: move OF helpers into the core
i2c: mv64xxx: Fix timing issue on Armada XP (errata FE-8471889)
i2c: mv64xxx: Add I2C Transaction Generator support
i2c: powermac: fix return path on error
Documentation: i2c: Fix example in instantiating-devices
i2c: tiny-usb: do not use stack as URB transfer_buffer
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull PTR_RET() removal patches from Rusty Russell:
"PTR_RET() is a weird name, and led to some confusing usage. We ended
up with PTR_ERR_OR_ZERO(), and replacing or fixing all the usages.
This has been sitting in linux-next for a whole cycle"
[ There are still some PTR_RET users scattered about, with some of them
possibly being new, but most of them existing in Rusty's tree too. We
have that
#define PTR_RET(p) PTR_ERR_OR_ZERO(p)
thing in <linux/err.h>, so they continue to work for now - Linus ]
* tag 'PTR_RET-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
GFS2: Replace PTR_RET with PTR_ERR_OR_ZERO
Btrfs: volume: Replace PTR_RET with PTR_ERR_OR_ZERO
drm/cma: Replace PTR_RET with PTR_ERR_OR_ZERO
sh_veu: Replace PTR_RET with PTR_ERR_OR_ZERO
dma-buf: Replace PTR_RET with PTR_ERR_OR_ZERO
drivers/rtc: Replace PTR_RET with PTR_ERR_OR_ZERO
mm/oom_kill: remove weird use of ERR_PTR()/PTR_ERR().
staging/zcache: don't use PTR_RET().
remoteproc: don't use PTR_RET().
pinctrl: don't use PTR_RET().
acpi: Replace weird use of PTR_RET.
s390: Replace weird use of PTR_RET.
PTR_RET is now PTR_ERR_OR_ZERO(): Replace most.
PTR_RET is now PTR_ERR_OR_ZERO
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg KH:
"Here's the big driver core pull request for 3.12-rc1.
Lots of tiny changes here fixing up the way sysfs attributes are
created, to try to make drivers simpler, and fix a whole class race
conditions with creations of device attributes after the device was
announced to userspace.
All the various pieces are acked by the different subsystem
maintainers"
* tag 'driver-core-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (119 commits)
firmware loader: fix pending_fw_head list corruption
drivers/base/memory.c: introduce help macro to_memory_block
dynamic debug: line queries failing due to uninitialized local variable
sysfs: sysfs_create_groups returns a value.
debugfs: provide debugfs_create_x64() when disabled
rbd: convert bus code to use bus_groups
firmware: dcdbas: use binary attribute groups
sysfs: add sysfs_create/remove_groups for when SYSFS is not enabled
driver core: add #include <linux/sysfs.h> to core files.
HID: convert bus code to use dev_groups
Input: serio: convert bus code to use drv_groups
Input: gameport: convert bus code to use drv_groups
driver core: firmware: use __ATTR_RW()
driver core: core: use DEVICE_ATTR_RO
driver core: bus: use DRIVER_ATTR_WO()
driver core: create write-only attribute macros for devices and drivers
sysfs: create __ATTR_WO()
driver-core: platform: convert bus code to use dev_groups
workqueue: convert bus code to use dev_groups
MEI: convert bus code to use dev_groups
...
|
|
Cards using the wm8775 specify that in their card struct. Those that do not
use it leave the audio_chip field to 0. Unfortunately, the CX88_AUDIO_WM8775
enum is 0 as well, so boards that do not have the wm8775 still try to load
and use that driver. Change it to 1 to fix this.
This regression was introduced in commit facd23664f1d63c33fbc6da52261c8548ed3fbd4.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Knut Petersen <Knut_Petersen@t-online.de>
Tested-by: Knut Petersen <Knut_Petersen@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: stable@vger.kernel.org
|
|
This patch corrects media entities unregistration order to make sure
the fimc.N.capture and fimc-lite video nodes are unregistered with
fimc->lock mutex held. This prevents races between video device open()
and defered probing and NULL pointer dereference in open() callback
as follows:
[ 77.645000] Unable to handle kernel NULL pointer dereference at virtual address 00000290t
[ 77.655000] pgd = ee7a8000
[ 77.660000] [00000290] *pgd=6e13c831, *pte=00000000, *ppte=00000000
[ 77.665000] Internal error: Oops: 17 [#1] PREEMPT SMP ARM
[ 77.670000] Modules linked in: s5p_fimc ipv6 exynos_fimc_is exynos_fimc_lite
s5p_csis v4l2_mem2mem videobuf2_dma_contig videobuf2_memops exynos4_is_common videobuf2_core [last unloaded: s5p_fimc]
[ 77.685000] CPU: 0 PID : 2998 Comm: v4l_id Tainted: G W 3.10.0-next-20130709-00039-g39f491b-dirty #1548
[ 77.695000] task: ee084000 ti: ee46e000 task.ti: ee46e000
[ 77.700000] PC is at __mutex_lock_slowpath+0x54/0x368
[ 77.705000] LR is at __mutex_lock_slowpath+0x24/0x368
[ 77.710000] pc : [<c038dc10>] lr : [<c038dbe0>] psr: 60000093
[ 77.710000] sp : ee46fd70 ip : 000008c8 fp : c054e34c
[ 77.725000] r10: ee084000 r9 : 00000000 r8 : ee439480
[ 77.730000] r7 : ee46e000 r6 : 60000013 r5 : 00000290 r4 : 0000028c
[ 77.735000] r3 : 00000000 r2 : 00000000 r1 : 20000093 r0 : 00000001
[ 77.740000] Flags: nZCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment user
[ 77.750000] Control: 10c5387d Table: 6e7a804a DAC: 00000015
[ 77.755000] Process v4l_id (pid: 2998, stack limit = 0xee46e238)
[ 77.760000] Stack: (0xee46fd70 to 0xee470000)
...
[ 77.935000] [<c038dc10>] (__mutex_lock_slowpath+0x54/0x368) from [<c038df30>] (mutex_lock+0xc/0x24)
[ 77.945000] [<c038df30>] (mutex_lock+0xc/0x24) from [<bf03fa90>] (fimc_lite_open+0x12c/0x2bc [exynos_fimc_lite])
[ 77.955000] [<bf03fa90>] (fimc_lite_open+0x12c/0x2bc [exynos_fimc_lite]) from [<c02ab11c>] (v4l2_open+0xa0/0xe0)
[ 77.965000] [<c02ab11c>] (v4l2_open+0xa0/0xe0) from [<c00b1de4>] (chrdev_open+0x88/0x170)
[ 77.975000] [<c00b1de4>] (chrdev_open+0x88/0x170) from [<c00ac710>] (do_dentry_open.isra.14+0x1d8/0x258)
[ 77.985000] [<c00ac710>] (do_dentry_open.isra.14+0x1d8/0x258) from [<c00ac860>] (finish_open+0x20/0x38)
[ 77.995000] [<c00ac860>] (finish_open+0x20/0x38) from [<c00ba658>] (do_last.isra.43+0x538/0xb1c)
[ 78.000000] [<c00ba658>] (do_last.isra.43+0x538/0xb1c) from [<c00bacf0>] (path_openat+0xb4/0x5c4)
[ 78.010000] [<c00bacf0>] (path_openat+0xb4/0x5c4) from [<c00bb4b4>] (do_filp_open+0x2c/0x80)
[ 78.020000] [<c00bb4b4>] (do_filp_open+0x2c/0x80) from [<c00ad744>] (do_sys_open+0xf4/0x1a8)
[ 78.025000] [<c00ad744>] (do_sys_open+0xf4/0x1a8) from [<c000e320>] (ret_fast_syscall+0x0/0x30)
[ 78.035000] Code: 1a000093 e10f6000 f10c0080 e2845004 (e1953f9f)
Reported-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: stable@vger.kernel.org
|
|
Gscaler video device registration was happening without reference to
a parent v4l2_dev causing probe to fail. The patch creates a parent
v4l2 device and uses it for the gsc m2m video device registration.
This fixes regression introduced with comit commit 1c1d86a1ea07506
[media] v4l2: always require v4l2_dev, rename parent to dev_parent
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: stable@vger.kernel.org
|
|
The 10-bit and 12-bit Bayer output formats supported by FIMC-LITE
actually use 16 bits where the extra bits are padded with zeros.
The patch corrects buffer allocation for these two formats by
modifying the depth field. This prevents memory corruption by the
output DMA due to insufficient buffer size.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: stable@vger.kernel.org
|
|
Set the config structure pointer to the eeprom data pointer (data,
here eedata dereferenced) not the pointer to the pointer to
the eeprom data (eedata itself).
Signed-off-by: Alban Browaeys <prahal@yahoo.com>
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Cc: stable@vger.kernel.org # for v3.10
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: stable@vger.kernel.org
|
|
free_buff_list and rec_buff_list are initialized in the middle of hdpvr_probe(),
but if something bad happens before that, error handling code calls hdpvr_delete(),
which contains iteration over the lists (via hdpvr_free_buffers()).
The patch moves the lists initialization to the beginning and by the way fixes
goto label in error handling of registering videodev.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: stable@vger.kernel.org
|
|
Ignore out of order data and mark incomplete buffers as errored.
This gets rid of annoying flicker due to occassional garbage from hardware.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-media@vger.kernel.org
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: stable@vger.kernel.org
|
|
The image data is laid out a bit more weirdly and thus needs more work to
properly interlace. What we get from hardware is V4L2_FIELD_ALTERNATE, but
since userspace support for it is practically nonexistent, thus we make
V4L2_FIELD_INTERLACED from it so that it's more easily interpreted.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: stable@vger.kernel.org
|
|
media_build/v4l/ml86v7667.c: In function 'ml86v7667_s_ctrl':
media_build/v4l/ml86v7667.c:120:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
int ret;
^
And indeed, ret is set but not used. Let's actually return the error
code.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Commit 1c1d86a1ea ("[media] v4l2: always require v4l2_dev,
rename parent to dev_parent") expects v4l2_dev to be always set.
It converted most of the drivers using the parent field of video_device
to v4l2_dev field. G2D driver did not set the parent field. Hence it got
left out. Without this patch we get the following boot warning and G2D
driver fails to register the video device.
WARNING: CPU: 0 PID: 1 at drivers/media/v4l2-core/v4l2-dev.c:775 __video_register_device+0xfc0/0x1028()
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.11.0-rc1-00001-g1c3e372-dirty #9
[<c0014b7c>] (unwind_backtrace+0x0/0xf4) from [<c0011524>] (show_stack+0x10/0x14)
[<c0011524>] (show_stack+0x10/0x14) from [<c041d7a8>] (dump_stack+0x7c/0xb0)
[<c041d7a8>] (dump_stack+0x7c/0xb0) from [<c001dc94>] (warn_slowpath_common+0x6c/0x88)
[<c001dc94>] (warn_slowpath_common+0x6c/0x88) from [<c001dd4c>] (warn_slowpath_null+0x1c/0x24)
[<c001dd4c>] (warn_slowpath_null+0x1c/0x24) from [<c02cf8d4>] (__video_register_device+0xfc0/0x1028)
[<c02cf8d4>] (__video_register_device+0xfc0/0x1028) from [<c0311a94>] (g2d_probe+0x1f8/0x398)
[<c0311a94>] (g2d_probe+0x1f8/0x398) from [<c0247d54>] (platform_drv_probe+0x14/0x18)
[<c0247d54>] (platform_drv_probe+0x14/0x18) from [<c0246b10>] (driver_probe_device+0x108/0x220)
[<c0246b10>] (driver_probe_device+0x108/0x220) from [<c0246cf8>] (__driver_attach+0x8c/0x90)
[<c0246cf8>] (__driver_attach+0x8c/0x90) from [<c0245050>] (bus_for_each_dev+0x60/0x94)
[<c0245050>] (bus_for_each_dev+0x60/0x94) from [<c02462c8>] (bus_add_driver+0x1c0/0x24c)
[<c02462c8>] (bus_add_driver+0x1c0/0x24c) from [<c02472d0>] (driver_register+0x78/0x140)
[<c02472d0>] (driver_register+0x78/0x140) from [<c00087c8>] (do_one_initcall+0xf8/0x144)
[<c00087c8>] (do_one_initcall+0xf8/0x144) from [<c05b29e8>] (kernel_init_freeable+0x13c/0x1d8)
[<c05b29e8>] (kernel_init_freeable+0x13c/0x1d8) from [<c041a108>] (kernel_init+0xc/0x160)
[<c041a108>] (kernel_init+0xc/0x160) from [<c000e2f8>] (ret_from_fork+0x14/0x3c)
---[ end trace 4e0ec028b0028e02 ]---
s5p-g2d 12800000.g2d: Failed to register video device
s5p-g2d: probe of 12800000.g2d failed with error -22
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: stable@vger.kernel.org
|
|
The data pointer should point to DT data, and not to the ID
array.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: stable@vger.kernel.org
|
|
The video encode/decode paths have duplicated logic between
VIDIOC_TRY_FMT and VIDIOC_S_FMT that should be de-duped. Also, video
decode reports V4L2_PIX_FMT_NV12MT_16X16 output format, regardless of
what the actual output has been set at. Fix this.
Signed-off-by: John Sheu <sheu@google.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: stable@vger.kernel.org
|
|
A mutex_lock() was left when the driver was converted to use the vb2
ioctl helpers, resulting in a deadlock at streamon time. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
