| Age | Commit message (Collapse) | Author |
|---|
|
commit 09c9d4c9b6a2b5909ae3c6265e4cd3820b636863 upstream.
Revert commit 224cb3e981f1b2f9f93dbd49eaef505d17d894c2
dm: Call blk_abort_queue on failed paths
Multipath began to use blk_abort_queue() to allow for
lower latency path deactivation. This was found to
cause list corruption:
the cmd gets blk_abort_queued/timedout run on it and the scsi eh
somehow is able to complete and run scsi_queue_insert while
scsi_request_fn is still trying to process the request.
https://www.redhat.com/archives/dm-devel/2010-November/msg00085.html
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: Mike Anderson <andmike@linux.vnet.ibm.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit c217649bf2d60ac119afd71d938278cffd55962b upstream.
No longer needlessly hold md->bdev->bd_inode->i_mutex when changing the
size of a DM device. This additional locking is unnecessary because
i_size_write() is already protected by the existing critical section in
dm_swap_table(). DM already has a reference on md->bdev so the
associated bd_inode may be changed without lifetime concerns.
A negative side-effect of having held md->bdev->bd_inode->i_mutex was
that a concurrent DM device resize and flush (via fsync) would deadlock.
Dropping md->bdev->bd_inode->i_mutex eliminates this potential for
deadlock. The following reproducer no longer deadlocks:
https://www.redhat.com/archives/dm-devel/2009-July/msg00284.html
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit e91ece5590b3c728624ab57043fc7a05069c604a upstream.
md_make_request was calling bio_sectors() for part_stat_add
after it was calling the make_request function. This is
bad because the make_request function can free the bio and
because the bi_size field can change around.
The fix here was suggested by Jens Axboe. It saves the
sector count before the make_request call. I hit this
with CONFIG_DEBUG_PAGEALLOC turned on while trying to break
his pretty fusionio card.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit bf2cb0dab8c97f00a71875d9b13dbac17a2f47ca upstream.
When a RAID6 is converted to a RAID5, the extra drive should
be discarded. However it isn't due to a typo in a comparison.
This bug was introduced in commit e93f68a1fc6 in 2.6.35-rc4
and is suitable for any -stable since than.
As the extra drive is not removed, the 'degraded' counter is wrong and
so the RAID5 will not respond correctly to a subsequent failure.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 0ca69886a8273ac1350143d562280bfcbe4760dc upstream.
When an md device is in the process of coming on line it is possible
for an IO request (typically a partition table probe) to get through
before the array is fully initialised, which can cause unexpected
behaviour (e.g. a crash).
So explicitly record when the array is ready for IO and don't allow IO
through until then.
There is no possibility for a similar problem when the array is going
off-line as there must only be one 'open' at that time, and it is busy
off-lining the array and so cannot send IO requests. So no memory
barrier is needed in md_stop()
This has been a bug since commit 409c57f3801 in 2.6.30 which
introduced md_make_request. Before then, each personality would
register its own make_request_fn when it was ready.
This is suitable for any stable kernel from 2.6.30.y onwards.
Signed-off-by: NeilBrown <neilb@suse.de>
Reported-by: "Hawrylewicz Czarnowski, Przemyslaw" <przemyslaw.hawrylewicz.czarnowski@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 6c9879101442b08581e8a0e3ae6b7f643a78fd63 upstream.
commit 589a594be1fb (2.6.37-rc4) fixed a problem were md_thread would
sometimes call the ->run function at a bad time.
If an error is detected during array start up after the md_thread has
been started, the md_thread is killed. This resulted in the ->run
function being called once. However the array may not be in a state
that it is safe to call ->run.
However the fix imposed meant that ->run was not called on a timeout.
This means that when an array goes idle, bitmap bits do not get
cleared promptly. While the array is busy the bits will still be
cleared when appropriate so this is not very serious. There is no
risk to data.
Change the test so that we only avoid calling ->run when the thread
is being stopped. This more explicitly addresses the problem situation.
This is suitable for 2.6.37-stable and any -stable kernel to which
589a594be1fb was applied.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit bf572541ab44240163eaa2d486b06f306a31d45a upstream.
Commit 1a855a0606 (2.6.37-rc4) fixed a problem where devices were
re-added when they shouldn't be but caused a regression in a less
common case that means sometimes devices cannot be re-added when they
should be.
In particular, when re-adding a device to an array without metadata
we should always access the device, but after the above commit we
didn't.
This patch sets the In_sync flag in that case so that the re-add
succeeds.
This patch is suitable for any -stable kernel to which 1a855a0606 was
applied.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit e692cb668fdd5a712c6ed2a2d6f2a36ee83997b4 upstream.
When stacking devices, a request_queue is not always available. This
forced us to have a no_cluster flag in the queue_limits that could be
used as a carrier until the request_queue had been set up for a
metadevice.
There were several problems with that approach. First of all it was up
to the stacking device to remember to set queue flag after stacking had
completed. Also, the queue flag and the queue limits had to be kept in
sync at all times. We got that wrong, which could lead to us issuing
commands that went beyond the max scatterlist limit set by the driver.
The proper fix is to avoid having two flags for tracking the same thing.
We deprecate QUEUE_FLAG_CLUSTER and use the queue limit directly in the
block layer merging functions. The queue_limit 'no_cluster' is turned
into 'cluster' to avoid double negatives and to ease stacking.
Clustering defaults to being enabled as before. The queue flag logic is
removed from the stacking function, and explicitly setting the cluster
flag is no longer necessary in DM and MD.
Reported-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 589a594be1fb8815b3f18e517be696c48664f728 upstream.
When we fail to start a raid10 for some reason, we call
md_unregister_thread to kill the thread that was created.
Unfortunately md_thread() will then make one call into the handler
(raid10d) even though md_wakeup_thread has not been called. This is
not safe and as md_unregister_thread is called after mddev->private
has been set to NULL, it will definitely cause a NULL dereference.
So fix this at both ends:
- md_thread should only call the handler if THREAD_WAKEUP has been
set.
- raid10 should call md_unregister_thread before setting things
to NULL just like all the other raid modules do.
This is applicable to 2.6.35 and later.
Reported-by: "Citizen" <citizen_lee@thecus.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 1a855a0606653d2d82506281e2c686bacb4b2f45 upstream.
With v0.90 metadata, a hot-spare does not become a full member of the
array until recovery is complete. So if we re-add such a device to
the array, we know that all of it is as up-to-date as the event count
would suggest, and so it a bitmap-based recovery is possible.
However with v1.x metadata, the hot-spare immediately becomes a full
member of the array, but it record how much of the device has been
recovered. If the array is stopped and re-assembled recovery starts
from this point.
When such a device is hot-added to an array we currently lose the 'how
much is recovered' information and incorrectly included it as a full
in-sync member (after bitmap-based fixup).
This is wrong and unsafe and could corrupt data.
So be more careful about setting saved_raid_disk - which is what
guides the re-adding of devices back into an array.
The new code matches the code in slot_store which does a similar
thing, which is encouraging.
This is suitable for any -stable kernel.
Reported-by: "Dailey, Nate" <Nate.Dailey@stratus.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit c26a44ed1e552aaa1d4ceb71842002d235fe98d7 upstream.
When trying to grow an array by enlarging component devices,
rdev_size_store() expects the return value of rdev_size_change() to be
in sectors, but the actual value is returned in KBs.
This functionality was broken by commit
dd8ac336c13fd8afdb082ebacb1cddd5cf727889
so this patch is suitable for any kernel since 2.6.30.
Signed-off-by: Justin Maggard <jmaggard10@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 8f9e0ee38f75d4740daa9e42c8af628d33d19a02 upstream.
Commit 4044ba58dd15cb01797c4fd034f39ef4a75f7cc3 supposedly fixed a
problem where if a raid1 with just one good device gets a read-error
during recovery, the recovery would abort and immediately restart in
an infinite loop.
However it depended on raid1_remove_disk removing the spare device
from the array. But that does not happen in this case. So add a test
so that in the 'recovery_disabled' case, the device will be removed.
This suitable for any kernel since 2.6.29 which is when
recovery_disabled was introduced.
Reported-by: Sebastian Färber <faerber@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit d97a41dc9c44f5829b7af7aa69fda10fd82b6b4e upstream.
A RAID1 which has no persistent metadata, whether internal or
external, will hang on the first write.
This is caused by commit 070dc6dd7103b6b3f7e4d46e754354a5c15f366e
In that case, MD_CHANGE_PENDING never gets cleared.
So during md_update_sb, is neither persistent or external,
clear MD_CHANGE_PENDING.
This is suitable for 2.6.36-stable.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Function read_sb_page may return ERR_PTR(...). Check for it.
Signed-off-by: Vasiliy Kulikov <segooon@gmail.com>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
When performing a resync we pre-allocate some bios and repeatedly use
them. This requires us to re-initialise them each time.
One field (bi_comp_cpu) and some flags weren't being initiaised
reliably.
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
bitmap_start_sync returns - via a pass-by-reference variable - the
number of sectors before we need to check with the bitmap again.
Since commit ef4256733506f245 this number can be substantially larger,
2^27 is a common value.
Unfortunately it is an 'int' and so when raid1.c:sync_request shifts
it 9 places to the left it becomes 0. This results in a zero-length
read which the scsi layer justifiably complains about.
This patch just removes the shift so the common case becomes safe with
a trivially-correct patch.
In the next merge window we will convert this 'int' to a 'sector_t'
Reported-by: "George Spelvin" <linux@horizon.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
If an array with 1.x metadata is assembled with the last disk missing,
md doesn't properly record the fact that the disk was missing.
This is unlikely to cause a real problem as the event count will be
different to the count on the missing disk so it won't be included in
the array. However it could still cause confusion.
So make sure we clear all the relevant slots, not just the early ones.
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Now that we depend on md_update_sb to clear variable bits in
mddev->flags (rather than trying not to set them) it is important to
always call md_update_sb when appropriate.
md_check_recovery has this job but explicitly avoids it for ->external
metadata arrays. This is not longer appropraite, or needed.
However we do want to avoid taking the mddev lock if only
MD_CHANGE_PENDING is set as that is not cleared by md_update_sb for
external-metadata arrays.
Reported-by: "Kwolek, Adam" <adam.kwolek@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
MD_CHANGE_CLEAN is used for two different purposes and this leads to
confusion.
One of the purposes is largely mirrored by MD_CHANGE_PENDING which is
not used for anything else, so have MD_CHANGE_PENDING take over that
purpose fully.
The two purposes are:
1/ tell md_update_sb that an update is needed and that it is just a
clean/dirty transition.
2/ tell user-space that an transition from clean to dirty is pending
(something wants to write), and tell te kernel (by clearin the
flag) that the transition is OK.
The first purpose remains wit MD_CHANGE_CLEAN, the second is moved
fully to MD_CHANGE_PENDING.
This means that various places which conditionally set or cleared
MD_CHANGE_CLEAN no longer need to be conditional.
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
If this bit is cleared in md_update_sb() the kernel will allow writes to the
array if userspace triggers md_allow_write(), e.g. through stripe_cache_size,
when mdmon is not active. When mdmon is active the array transitions to
active-idle bypassing write-pending, setting up a race for mdmon to set the
array clean before a write arrives.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Another missing bit of the raid6 -> /lib move.
Reported-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
commit 7b6d91daee5cac6402186ff224c3af39d79f4a0e changed the behaviour
of a few variables in raid1 and raid10 from flags to bit-sets, but
left them as type 'bool' so they did not work.
Change them (back) to unsigned long.
(historical note: see 1ef04fefe2241087d9db7e9615c3f11b516e36cf)
Signed-off-by: NeilBrown <neilb@suse.de>
Reported-by: Jiri Slaby <jslaby@suse.cz> and many others
|
|
md_check_recovery expects ->spare_active to return 'true' if any
spares were activated, but none of them do, so the consequent change
in 'degraded' is not notified through sysfs.
So count the number of spares activated, subtract it from 'degraded'
just once, and return it.
Reported-by: Adrian Drzewiecki <adriand@vmware.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
When RAID1 is done syncing disks, it'll update the state
of synced rdevs to In_sync. But it neglected to notify
sysfs that the attribute changed. So any programs that
are waiting for an rdev's state to change will not be
woken.
(raid5/raid10 added by neilb)
Signed-off-by: Adrian Drzewiecki <adriand@vmware.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
The update of ->recovery_offset in sync_sbs is appropriate even then external
metadata is in use. However sync_sbs is only called when native
metadata is used.
So move that update in to the top of md_update_sb (which is the only
caller of sync_sbs) before the test on ->external.
This moves the update out of ->write_lock protection, but those fields
only need ->reconfig_mutex protection which they still have.
Also move the test on ->persistent up to where ->external is set as
for metadata update purposes they are the same.
Clear MD_CHANGE_DEVS and MD_CHANGE_CLEAN as they can only be confusing
if ->external is set or ->persistent isn't.
Finally move the update of ->utime down as it is only relevent (like
the ->events update) for native metadata.
Signed-off-by: NeilBrown <neilb@suse.de>
Reported-by: "Kwolek, Adam" <adam.kwolek@intel.com>
|
|
Enable discard support in the DM multipath target.
This discard support depends on a few discard-specific fixes to the
block layer's request stacking driver methods.
Discard requests are optional so don't allow a failed discard to trigger
path failures. If there is a real problem with a given path the
barriers associated with the discard (either before or after the
discard) will cause path failure. That said, unconditionally passing
discard failures up the stack is not ideal. This must be fixed once DM
has more information about the nature of the underlying storage failure.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
|
|
The DM core will submit a discard bio to the stripe target for each
stripe in a striped DM device. The stripe target will determine
stripe-specific portions of the supplied bio to be remapped into
individual (at most 'num_discard_requests' extents). If a given
stripe-specific discard bio doesn't touch a particular stripe the bio
will be dropped.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
Update __clone_and_map_discard to loop across all targets in a DM
device's table when it processes a discard bio. If a discard crosses a
target boundary it must be split accordingly.
Update __issue_target_requests and __issue_target_request to allow a
cloned discard bio to have a custom start sector and size.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
Optimize sector division: If the number of stripes is a power of two,
we can do shift and mask instead of division.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
Move sector to stripe translation into a function.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
Have the error target respond to a discard request with a hard -EIO
rather than fail the request with -EOPNOTSUPP.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
Enable discard support for the delay target.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
Have the zero target silently drop a discard rather than fail the
request with -EOPNOTSUPP.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
Use new dm_target_offset() macro to avoid most references to ti->begin
in dm targets.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
Split max_io_len_target_boundary out of max_io_len so that the discard
support can make use of it without duplicating max_io_len code.
Avoiding max_io_len's split_io logic enables DM's discard support to
submit the entire discard request to a target. But discards must still
be split on target boundaries.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
Rename __flush_target to __issue_target_request now that it is used to
issue both flush and discard requests.
Introduce __issue_target_requests as a convenient wrapper to
__issue_target_request 'num_flush_requests' or 'num_discard_requests'
times per target.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
Allow discards to be passed through to linear mappings if at least one
underlying device supports it. Discards will be forwarded only to
devices that support them.
A target that supports discards should set num_discard_requests to
indicate how many times each discard request must be submitted to it.
Verify table's underlying devices support discards prior to setting the
associated DM device as capable of discards (via QUEUE_FLAG_DISCARD).
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Joe Thornber <thornber@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
Allocate cipher strings indpendently of struct crypt_config and move
cipher parsing and allocation into a separate function to prepare for
supporting the cryptoapi format e.g. "xts(aes)".
No functional change in this patch.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
Use just one label and reuse common destructor for crypt target.
Parse remaining argv arguments in logic order.
Also do not ignore error values from IV init and set key functions.
No functional change in this patch except changed return codes
based on above.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
Add devname:mapper/control and MAPPER_CTRL_MINOR module alias
to support dm-mod module autoloading.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Peter Rajnoha <prajnoha@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
'target_request_nr' is a more generic name that reflects the fact that
it will be used for both flush and discard support.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
This change unifies the various checks and finalization that occurs on a
table prior to use. By doing so, it allows table construction without
traversing the dm-ioctl interface.
Signed-off-by: Will Drewry <wad@chromium.org>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
Implement merge method for the snapshot origin to improve read
performance.
Without merge method, dm asks the upper layers to submit smallest possible
bios --- one page. Submitting such small bios impacts performance negatively
when reading or writing the origin device.
Without this patch, CPU consumption when reading the origin on lvm on md-raid0
was 6 to 12%, with this patch, it drops to 1 to 4%.
Note: in my testing, it actually degraded performance in some settings, I
traced it to Maxtor disks having problems with > 512-sector requests.
Reducing the number of sectors to /sys/block/sd*/queue/max_sectors_kb to
256 fixed the read performance. I think we don't have to care about weird
disks that actually degrade performance because of large requests being
sent to them.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
Change bio-based mapped devices no longer to have a fully initialized
request_queue (request_fn, elevator, etc). This means bio-based DM
devices no longer register elevator sysfs attributes ('iosched/' tree
or 'scheduler' other than "none").
In contrast, a request-based DM device will continue to have a full
request_queue and will register elevator sysfs attributes. Therefore
a user can determine a DM device's type by checking if elevator sysfs
attributes exist.
First allocate a minimalist request_queue structure for a DM device
(needed for both bio and request-based DM).
Initialization of a full request_queue is deferred until it is known
that the DM device is request-based, at the end of the table load
sequence.
Factor DM device's request_queue initialization:
- common to both request-based and bio-based into dm_init_md_queue().
- specific to request-based into dm_init_request_based_queue().
The md->type_lock mutex is used to protect md->queue, in addition to
md->type, during table_load().
A DM device's first table_load will establish the immutable md->type.
But md->queue initialization, based on md->type, may fail at that time
(because blk_init_allocated_queue cannot allocate memory). Therefore
any subsequent table_load must (re)try dm_setup_md_queue independently of
establishing md->type.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
Determine whether a mapped device is bio-based or request-based when
loading its first (inactive) table and don't allow that to be changed
later.
This patch performs different device initialisation in each of the two
cases. (We don't think it's necessary to add code to support changing
between the two types.)
Allowed md->type transitions:
DM_TYPE_NONE to DM_TYPE_BIO_BASED
DM_TYPE_NONE to DM_TYPE_REQUEST_BASED
We now prevent table_load from replacing the inactive table with a
conflicting type of table even after an explicit table_clear.
Introduce 'type_lock' into the struct mapped_device to protect md->type
and to prepare for the next patch that will change the queue
initialization and allocate memory while md->type_lock is held.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
drivers/md/dm-ioctl.c | 15 +++++++++++++++
drivers/md/dm.c | 37 ++++++++++++++++++++++++++++++-------
drivers/md/dm.h | 5 +++++
include/linux/dm-ioctl.h | 4 ++--
4 files changed, 52 insertions(+), 9 deletions(-)
|
|
When processing barriers, skip the second flush if processing the bio
failed with -EOPNOTSUPP. This can happen with discard+barrier requests.
If the device doesn't support discard, there would be two useless
SYNCHRONIZE CACHE commands. The first dm_flush cannot be so easily
optimized out, so we leave it there.
Previously, -EOPNOTSUPP could be received in dec_pending only with empty
barriers and we ignored that error, assuming the device not supporting
cache flushes has cache always consistent. With the addition of discard
barriers, this -EOPNOTSUPP can also be generated by discards and we
must record it in md->barrier_error for process_barrier.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
This patch fixes hard-coded value for the size of a chunk that includes
disk header for persistent snapshot. It should be changed to existing
macro NUM_SNAPSHOT_HDR_CHUNKS instead of using hard-coded value 1.
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@jp.fujitsu.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
Use kstrdup when the goal of an allocation is copy a string into the
allocated region.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression from,to;
expression flag,E1,E2;
statement S;
@@
- to = kmalloc(strlen(from) + 1,flag);
+ to = kstrdup(from, flag);
... when != \(from = E1 \| to = E1 \)
if (to==NULL || ...) S
... when != \(from = E2 \| to = E2 \)
- strcpy(to, from);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
The dm control device does not implement read/write, so it has no use for
seeking. Using no_llseek prevents falling back to default_llseek, which
requires the BKL.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
This patch separates the device deletion code from dm_put()
to make sure the deletion happens in the process context.
By this patch, device deletion always occurs in an ioctl (process)
context and dm_put() can be called in interrupt context.
As a result, the request-based dm's bad dm_put() usage pointed out
by Mikulas below disappears.
http://marc.info/?l=dm-devel&m=126699981019735&w=2
Without this patch, I confirmed there is a case to crash the system:
dm_put() => dm_table_destroy() => vfree() => BUG_ON(in_interrupt())
Some more backgrounds and details:
In request-based dm, a device opener can remove a mapped_device
while the last request is still completing, because bios in the last
request complete first and then the device opener can close and remove
the mapped_device before the last request completes:
CPU0 CPU1
=================================================================
<<INTERRUPT>>
blk_end_request_all(clone_rq)
blk_update_request(clone_rq)
bio_endio(clone_bio) == end_clone_bio
blk_update_request(orig_rq)
bio_endio(orig_bio)
<<I/O completed>>
dm_blk_close()
dev_remove()
dm_put(md)
<<Free md>>
blk_finish_request(clone_rq)
....
dm_end_request(clone_rq)
free_rq_clone(clone_rq)
blk_end_request_all(orig_rq)
rq_completed(md)
So request-based dm used dm_get()/dm_put() to hold md for each I/O
until its request completion handling is fully done.
However, the final dm_put() can call the device deletion code which
must not be run in interrupt context and may cause kernel panic.
To solve the problem, this patch moves the device deletion code,
dm_destroy(), to predetermined places that is actually deleting
the mapped_device in ioctl (process) context, and changes dm_put()
just to decrement the reference count of the mapped_device.
By this change, dm_put() can be used in any context and the symmetric
model below is introduced:
dm_create(): create a mapped_device
dm_destroy(): destroy a mapped_device
dm_get(): increment the reference count of a mapped_device
dm_put(): decrement the reference count of a mapped_device
dm_destroy() waits for all references of the mapped_device to disappear,
then deletes the mapped_device.
dm_destroy() uses active waiting with msleep(1), since deleting
the mapped_device isn't performance-critical task.
And since at this point, nobody opens the mapped_device and no new
reference will be taken, the pending counts are just for racing
completing activity and will eventually decrease to zero.
For the unlikely case of the forced module unload, dm_destroy_immediate(),
which doesn't wait and forcibly deletes the mapped_device, is also
introduced and used in dm_hash_remove_all(). Otherwise, "rmmod -f"
may be stuck and never return.
And now, because the mapped_device is deleted at this point, subsequent
accesses to the mapped_device may cause NULL pointer references.
Cc: stable@kernel.org
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
