summaryrefslogtreecommitdiff
path: root/drivers/input/mouse
AgeCommit message (Collapse)Author
2014-04-03Input: cypress_ps2 - don't report as a button padsHans de Goede
commit 6797b39e6f6f34c74177736e146406e894b9482b upstream. The cypress PS/2 trackpad models supported by the cypress_ps2 driver emulate BTN_RIGHT events in firmware based on the finger position, as part of this no motion events are sent when the finger is in the button area. The INPUT_PROP_BUTTONPAD property is there to indicate to userspace that BTN_RIGHT events should be emulated in userspace, which is not necessary in this case. When INPUT_PROP_BUTTONPAD is advertised userspace will wait for a motion event before propagating the button event higher up the stack, as it needs current abs x + y data for its BTN_RIGHT emulation. Since in the cypress_ps2 pads don't report motion events in the button area, this means that clicks in the button area end up being ignored, so INPUT_PROP_BUTTONPAD actually causes problems for these touchpads, and removing it fixes: https://bugs.freedesktop.org/show_bug.cgi?id=76341 Reported-by: Adam Williamson <awilliam@redhat.com> Tested-by: Adam Williamson <awilliam@redhat.com> Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
2014-04-03Input: synaptics - add manual min/max quirk for ThinkPad X240Hans de Goede
commit 8a0435d958fb36d93b8df610124a0e91e5675c82 upstream. This extends Benjamin Tissoires manual min/max quirk table with support for the ThinkPad X240. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
2014-04-03Input: synaptics - add manual min/max quirkBenjamin Tissoires
commit 421e08c41fda1f0c2ff6af81a67b491389b653a5 upstream. The new Lenovo Haswell series (-40's) contains a new Synaptics touchpad. However, these new Synaptics devices report bad axis ranges. Under Windows, it is not a problem because the Windows driver uses RMI4 over SMBus to talk to the device. Under Linux, we are using the PS/2 fallback interface and it occurs the reported ranges are wrong. Of course, it would be too easy to have only one range for the whole series, each touchpad seems to be calibrated in a different way. We can not use SMBus to get the actual range because I suspect the firmware will switch into the SMBus mode and stop talking through PS/2 (this is the case for hybrid HID over I2C / PS/2 Synaptics touchpads). So as a temporary solution (until RMI4 land into upstream), start a new list of quirks with the min/max manually set. Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
2014-03-31Input: elantech - improve clickpad detectionHans de Goede
commit c15bdfd5b9831e4cab8cfc118243956e267dd30e upstream. The current assumption in the elantech driver that hw version 3 touchpads are never clickpads and hw version 4 touchpads are always clickpads is wrong. There are several bug reports for this, ie: https://bugzilla.redhat.com/show_bug.cgi?id=1030802 http://superuser.com/questions/619582/right-elantech-touchpad-button-not-working-in-linux I've spend a couple of hours wading through various bugzillas, launchpads and forum posts to create a list of fw-versions and capabilities for different laptop models to find a good method to differentiate between clickpads and versions with separate hardware buttons. Which shows that a device being a clickpad is reliable indicated by bit 12 being set in the fw_version. I've included the gathered list inside the driver, so that we've this info at hand if we need to revisit this later. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Cc: Josh Boyer <jwboyer@fedoraproject.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
2013-12-20Input: elantech - add support for newer (August 2013) devicesMatt Walker
commit 9cb80b965eaf7af1369f6e16f48a05fbaaccc021 upstream. Added detection for newer Elantech touchpads, so that kernel doesn't fall-back to default PS/2 driver. Supports touchpads released after ~August 2013. Fixes bug: https://lists.launchpad.net/kernel-packages/msg18481.html Tested on an Acer Aspire S7-392-6302. Signed-off by: Matt Walker <matt.g.d.walker@gmail.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-04Input: cypress_ps2 - do not consider data bad if palm is detectedJoseph Salisbury
commit 5df682b297f6b23ec35615ed7bb50cbb25d25869 upstream. If hardware (or firmware) detects palm on the surface of the device it does not mean that the data packet is bad from the protocol standpoint. Instead of reporting PSMOUSE_BAD_DATA in this case simply threat it as if nothing touches the surface. BugLink: http://bugs.launchpad.net/bugs/1229361 Signed-off-by: Joseph Salisbury <joseph.salisbury@canonical.com> Tested-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-04Revert "Input: ALPS - add support for model found on Dell XT2"Dmitry Torokhov
commit 936816161978ca716a56c5e553c68f25972b1e3a upstream. This reverts commit 5beea882e64121dfe3b33145767d3302afa784d5 as it breaks trackpoint operation on XT2. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-10-31Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input Pull input updates from Dmitry Torokhov: "A bit later than I would want, but the changes are very minor - a few new device IDs for new hardware in existing drivers, fix for battery in Wacom devices not be considered system battery and cause emergency hibernations, and a couple of other bug fixes" * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: Input: ALPS - add support for model found on Dell XT2 Input: wacom - add support for ISDv4 0x10E sensor Input: wacom - add support for ISDv4 0x10F sensor Input: wacom - export battery scope Input: cm109 - convert high volume dev_err() to dev_err_ratelimited() Input: move name/timer init to input_alloc_dev() Input: i8042 - i8042_flush fix for a full 8042 buffer Input: pxa27x_keypad - fix NULL pointer dereference
2013-10-31Input: ALPS - add support for model found on Dell XT2Yunkang Tang
This patch adds support for touchpad found on Dell XT2. It's a dual device with device ID: 73, 00, 14, that comply with "ALPS_PROTO_V2". Signed-off-by: Yunkang Tang <yunkang.tang@cn.alps.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2013-09-07Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input Pull input updates from Dmitry Torokhov: "A new driver for slidebar on Ideapad laptops and a bunch of assorted driver fixes" * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (32 commits) Input: add SYN_MAX and SYN_CNT constants Input: max11801_ts - convert to devm Input: egalax-ts - fix typo and improve text Input: MAINTAINERS - change maintainer for cyttsp driver Input: cyttsp4 - kill 'defined but not used' compiler warnings Input: add driver for slidebar on Lenovo IdeaPad laptops Input: omap-keypad - set up irq type from DT Input: omap-keypad - enable wakeup capability for keypad. Input: omap-keypad - clear interrupts on open Input: omap-keypad - convert to threaded IRQ Input: omap-keypad - use bitfiled instead of hardcoded values Input: cyttsp4 - remove useless NULL test from cyttsp4_watchdog_timer() Input: wacom - fix error return code in wacom_probe() Input: as5011 - fix error return code in as5011_probe() Input: keyboard, serio - simplify use of devm_ioremap_resource Input: tegra-kbc - simplify use of devm_ioremap_resource Input: htcpen - fix incorrect placement of __initdata Input: qt1070 - add power management ops Input: wistron_btns - add MODULE_DEVICE_TABLE Input: wistron_btns - mark the Medion MD96500 keymap as tested ...
2013-09-06Merge branch 'next' into for-linusDmitry Torokhov
Merge first round of changes for 3.12 merge window.
2013-09-06Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid Pull HID updates from Jiri Kosina: "Highlights: - conversion of HID subsystem to use devm-based resource management, from Benjamin Tissoires - i2c-hid support for DT bindings, from Benjamin Tissoires - much improved support for Win8-multitouch devices, from Benjamin Tissoires - cleanup of core code using common hidinput_input_event(), from David Herrmann - fix for bug in implement() access to the bit stream (causing oops) that has been present in the code for ages, but devices that are able to trigger it have started to appear only now, from Jiri Kosina - fixes for CVE-2013-2899, CVE-2013-2898, CVE-2013-2896, CVE-2013-2892, CVE-2013-2888 (all triggerable only by specially crafted malicious HW devices plugged into the system), from Kees Cook - hidraw oops fix, from Manoj Chourasia - various smaller fixes here and there, support for a bunch of new devices by various contributors" * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (53 commits) HID: MAINTAINERS: add roccat drivers HID: hid-sensor-hub: change kmalloc + memcpy by kmemdup HID: hid-sensor-hub: move to devm_kzalloc HID: hid-sensor-hub: fix indentation accross the code HID: move HID_REPORT_TYPES closer to the report-definitions HID: check for NULL field when setting values HID: picolcd_core: validate output report details HID: sensor-hub: validate feature report details HID: ntrig: validate feature report details HID: pantherlord: validate output report details HID: hid-wiimote: print small buffers via %*phC HID: uhid: improve uhid example client HID: Correct the USB IDs for the new Macbook Air 6 HID: wiimote: add support for Guitar-Hero guitars HID: wiimote: add support for Guitar-Hero drums Input: introduce BTN/ABS bits for drums and guitars HID: battery: don't do DMA from stack HID: roccat: add support for KonePureOptical v2 HID: picolcd: Prevent NULL pointer dereference on _remove() HID: usbhid: quirk for N-Trig DuoSense Touch Screen ...
2013-09-04HID: Correct the USB IDs for the new Macbook Air 6Henrik Rydberg
A recent patch (9d9a04ee) added support for the new machine, but got the sequence of USB ids wrong. Reports from both Ian and Linus T show that the 0x0291 id is for ISO, not ANSI, which should have the missing number 0x0290. This patchs moves the three numbers accordingly, fixing the problem. Reported-and-tested-by: Ian Munsie <darkstarsword@gmail.com> Tested-by: Linus G Thiel <linus@hanssonlarsson.se> Signed-off-by: Henrik Rydberg <rydberg@euromail.se> Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2013-08-24Input: elantech - fix packet check for v3 and v4 hardwareMatteo Delfino
The signatures of v3 and v4 packets change depending on the value of a hardware flag called 'crc_enabled'. The packet type detection must change accordingly. This patch also restores a consistency check for v4 packets inadvertently removed by commit: 9eebed7de660c0b5ab129a9de4f89d20b60de68c Input: elantech - fix for newer hardware versions (v7) A note about the naming convention: v3 hardware is associated with IC body v5 while v4 hardware is associated with IC body v6 and v7. The above commit refers to IC body v7, not to v7 hardware. Tested on Samsung NP730U3E (fw = 0x675f05, ICv7, crc_enabled = 1) Tested-by: Giovanni Frigione <gio.frigione@gmail.com> Signed-off-by: Matteo Delfino <kendatsuba@gmail.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2013-08-12Input: synaptics - fix incorrect placement of __initconstSachin Kamat
__initconst should be placed between the variable name and equal sign for the variable to be placed in the intended section. Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2013-08-12Input: lifebook - fix incorrect placement of __initconstSachin Kamat
__initconst should be placed between the variable name and equal sign for the variable to be placed in the intended section. Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2013-07-12Merge branch 'next' into for-linusDmitry Torokhov
Bring in second round of updates for 3.11.
2013-07-06Input: elantech - fix for newer hardware versions (v7)Matteo Delfino
* Fix version recognition in elantech_set_properties The new hardware reports itself as v7 but the packets' structure is unaltered. * Fix packet type recognition in elantech_packet_check_v4 The bitmask used for v6 is too wide, only the last three bits of the third byte in a packet (packet[3] & 0x03) are actually used to distinguish between packet types. Starting from v7, additional information (to be interpreted) is stored in the remaining bits (packets[3] & 0x1c). In addition, the value stored in (packet[0] & 0x0c) is no longer a constant but contains additional information yet to be deciphered. This change should be backwards compatible with v6 hardware. Additional-author: Giovanni Frigione <gio.frigione@gmail.com> Signed-off-by: Matteo Delfino <kendatsuba@gmail.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2013-07-02Input: bcm5974 - add support for the 2013 MacBook AirDmitry Torokhov
The June 2013 Macbook Air (13'') has a new trackpad protocol; four new values are inserted in the header, and the mode switch is no longer needed. This patch adds support for the new devices. Cc: stable@vger.kernel.org Reported-and-tested-by: Brad Ford <plymouthffl@gmail.com> Signed-off-by: Henrik Rydberg <rydberg@euromail.se> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2013-06-27Merge branch 'for-next' of git://github.com/rydberg/linux into nextDmitry Torokhov
Pull in changes from Henrik: "a trivial MT documentation fix".
2013-06-05Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input Pull input fixes from Dmitry Torokhov: "Just a 2 small driver fixups here" * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: Input: wacom - fix a typo for Cintiq 22HDT Input: synaptics - fix sync lost after resume on some laptops
2013-06-04Input: synaptics - fix sync lost after resume on some laptopsEric Miao
In summary, the symptom is intermittent key events lost after resume on some machines with synaptics touchpad (seems this is synaptics _only_), and key events loss is due to serio port reconnect after psmouse sync lost. Removing psmouse and inserting it back during the suspend/resume process is able to work around the issue, so the difference between psmouse_connect() and psmouse_reconnect() is the key to the root cause of this problem. After comparing the two different paths, synaptics driver has its own implementation of synaptics_reconnect(), and the missing psmouse_probe() seems significant, the patch below added psmouse_probe() to the reconnect process, and has been verified many times that the issue could not be reliably reproduced. There are two PS/2 commands in psmouse_probe(): 1. PSMOUSE_CMD_GETID 2. PSMOUSE_CMD_RESET_DIS Only the PSMOUSE_CMD_GETID seems to be significant. The PSMOUSE_CMD_RESET_DIS is irrelevant to this issue after trying several times. So we have only implemented this patch to issue the PSMOUSE_CMD_GETID so far. Tested-by: Daniel Manrique <daniel.manrique@canonical.com> Signed-off-by: James M Leddy <james.leddy@canonical.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2013-05-23Input: navpoint - pass correct pointer to free_irq()Lars-Peter Clausen
free_irq() expects the same pointer that was passed to request_irq(), otherwise the IRQ is not freed. The issue was found using the following coccinelle script: <smpl> @r1@ type T; T devid; @@ request_irq(..., devid) @r2@ type r1.T; T devid; position p; @@ free_irq@p(..., devid) @@ position p != r2.p; @@ *free_irq@p(...) </smpl> Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2013-05-09Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linuxLinus Torvalds
Pull removal of GENERIC_GPIO from Grant Likely: "GENERIC_GPIO now synonymous with GPIOLIB. There are no longer any valid cases for enableing GENERIC_GPIO without GPIOLIB, even though it is possible to do so which has been causing confusion and breakage. This branch does the work to completely eliminate GENERIC_GPIO." * tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux: gpio: update gpio Chinese documentation Remove GENERIC_GPIO config option Convert selectors of GENERIC_GPIO to GPIOLIB blackfin: force use of gpiolib m68k: coldfire: use gpiolib mips: pnx833x: remove requirement for GENERIC_GPIO openrisc: default GENERIC_GPIO to false avr32: default GENERIC_GPIO to false xtensa: remove explicit selection of GENERIC_GPIO sh: replace CONFIG_GENERIC_GPIO by CONFIG_GPIOLIB powerpc: remove redundant GENERIC_GPIO selection unicore32: default GENERIC_GPIO to false unicore32: remove unneeded select GENERIC_GPIO arm: plat-orion: use GPIO driver on CONFIG_GPIOLIB arm: remove redundant GENERIC_GPIO selection mips: alchemy: require gpiolib mips: txx9: change GENERIC_GPIO to GPIOLIB mips: loongson: use GPIO driver on CONFIG_GPIOLIB mips: remove redundant GENERIC_GPIO select
2013-05-05Input: gpio_mouse - remove redundant platform_set_drvdata()Sachin Kamat
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no driver is bound) removes the need to set driver data field to NULL. Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2013-05-05Input: amimouse - remove redundant platform_set_drvdata()Sachin Kamat
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no driver is bound) removes the need to set driver data field to NULL. Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2013-04-19Input: trackpoint - Optimize trackpoint init to use power-on resetShawn Nematbakhsh
The trackpoint driver sets various parameter default values, all of which happen to be power-on defaults (Source: IBM TrackPoint Engineering Specification, Version 4.0. Also confirmed by empirical data). By sending the power-on reset command to reset all parameters to power-on state, we can skip the lengthy process of programming all parameters. In testing, ~2.5 secs of time writing parameters was reduced to .35 seconds waiting for power-on reset to complete. Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2013-04-16Convert selectors of GENERIC_GPIO to GPIOLIBAlexandre Courbot
GENERIC_GPIO is now equivalent to GPIOLIB and features that depended on GENERIC_GPIO can now depend on GPIOLIB to allow removal of this option. Signed-off-by: Alexandre Courbot <acourbot@nvidia.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Grant Likely <grant.likely@secretlab.ca>
2013-04-15Input: ALPS - use %ph to print buffersDmitry Torokhov
This form is more concise. Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2013-03-17Input: amimouse - use module_platform_driver_probe macroSachin Kamat
module_platform_driver_probe() eliminates the boilerplate and simplifies the code. Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2013-02-22Input: ALPS - add "Dolphin V1" touchpad supportDave Turvene
These touchpads use a different protocol; they have been seen on Dell N5110, Dell 17R SE, and others. The official ALPS driver identifies them by looking for an exact match on the E7 report: 73 03 50. Dolphin V1 returns an EC report of 73 01 xx (02 and 0d have been seen); Dolphin V2 returns an EC report of 73 02 xx (02 has been seen). Dolphin V2 probably needs a different initialization sequence and/or report parser, so it is left for a future commit. Signed-off-by: Dave Turvene <dturvene@dahetral.com> Signed-off-by: Kevin Cernekee <cernekee@gmail.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2013-02-22Input: ALPS - remove unused argument to alps_enter_command_mode()Kevin Cernekee
Now that alps_identify() explicitly issues an EC report using alps_rpt_cmd(), we no longer need to look at the magic numbers returned by alps_enter_command_mode(). Signed-off-by: Kevin Cernekee <cernekee@gmail.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2013-02-22Input: cypress_ps2 - fix trackpadi found in Dell XPS12Kamal Mostafa
Avoid firmware glitch in Cypress PS/2 Trackpad firmware version 11 (as observed in Dell XPS12) which prevents driver from recognizing the trackpad. BugLink: http://launchpad.net/bugs/1103594 Signed-off-by: Kamal Mostafa <kamal@canonical.com> Cc: Dudley Du <dudl@cypress.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2013-02-19Merge branch 'next' into for-linusDmitry Torokhov
Prepare first set of updates for 3.9 merge window.
2013-02-15Input: synaptics - initialize pointer emulation usageHenrik Rydberg
To properly setup event parameters for emulated events, pass the appropriate flag to the slot initialization function. Also, all MT-related events should be setup before initialization. Incidentally, this solves the issue of doubly filtered pointer events. Reported-by: Daniel Kurtz <djkurtz@chromium.org> Signed-off-by: Henrik Rydberg <rydberg@euromail.se> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2013-02-14Input: ALPS - enable trackstick on Rushmore touchpadsKevin Cernekee
Separate out the common trackstick probe/setup sequences, then call them from each of the v3 init functions. Credits: Emmanual Thome furnished the information on the trackstick init and how it affected the report format. Signed-off-by: Kevin Cernekee <cernekee@gmail.com> Tested-by: Dave Turvene <dturvene@dahetral.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2013-02-14Input: ALPS - add support for "Rushmore" touchpadsKevin Cernekee
Rushmore touchpads are found on Dell E6230/E6430/E6530. They use the V3 protocol with slightly tweaked init sequences and report formats. The E7 report is 73 03 0a, and the EC report is 88 08 1d Credits: Emmanuel Thome reported the MT bitmap changes. Signed-off-by: Kevin Cernekee <cernekee@gmail.com> Tested-by: Dave Turvene <dturvene@dahetral.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2013-02-14Input: ALPS - make the V3 packet field decoder "pluggable"Kevin Cernekee
A number of different ALPS touchpad protocols can reuse alps_process_touchpad_packet_v3() with small tweaks to the bitfield decoding. Create a new priv->decode_fields() callback that handles the per-model differences. Signed-off-by: Kevin Cernekee <cernekee@gmail.com> Tested-by: Dave Turvene <dturvene@dahetral.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2013-02-14Input: ALPS - move pixel and bitmap info into alps_data structKevin Cernekee
Newer touchpads use different constants, so make them runtime- configurable. Signed-off-by: Kevin Cernekee <cernekee@gmail.com> Tested-by: Dave Turvene <dturvene@dahetral.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2013-02-14Input: ALPS - fix command mode checkKevin Cernekee
Pinnacle class devices should return "88 07 xx" or "88 08 xx" when entering command mode. If either the first byte or the second byte is invalid, return an error. Signed-off-by: Kevin Cernekee <cernekee@gmail.com> Tested-by: Dave Turvene <dturvene@dahetral.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2013-02-14Input: ALPS - rework detection of Pinnacle AGx touchpadsKevin Cernekee
The official ALPS driver uses the EC report, not the E7 report, to detect these devices. Also, they check for a range of values; the original table-based code only checked for two specific ones. Signed-off-by: Kevin Cernekee <cernekee@gmail.com> Tested-by: Dave Turvene <dturvene@dahetral.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2013-02-14Input: ALPS - move {addr,nibble}_command settings into alps_set_defaults()Kevin Cernekee
This allows alps_identify() to override these settings based on the device characteristics, if it is ever necessary. Signed-off-by: Kevin Cernekee <cernekee@gmail.com> Tested-by: Dave Turvene <dturvene@dahetral.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2013-02-14Input: ALPS - use function pointers for different protocol handlersKevin Cernekee
In anticipation of adding more ALPS protocols and more per-device quirks, use function pointers instead of switch statements to call functions that differ from one device to the next. Signed-off-by: Kevin Cernekee <cernekee@gmail.com> Tested-by: Dave Turvene <dturvene@dahetral.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2013-02-14Input: ALPS - rework detection sequenceKevin Cernekee
If the E6 report test passes, get the E7 and EC reports right away and then try to match an entry in the table. Pass in the alps_data struct, so that the detection code will be able to set operating parameters based on information found during detection. Change the version (psmouse->model) to report the protocol version only, in preparation for supporting models that do not show up in the ID table. Signed-off-by: Kevin Cernekee <cernekee@gmail.com> Tested-by: Dave Turvene <dturvene@dahetral.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2013-02-14Input: ALPS - introduce helper function for repeated commandsKevin Cernekee
Several ALPS driver init sequences repeat a command three times, then issue PSMOUSE_CMD_GETINFO to read the result. Move this into a helper function to simplify the code. Signed-off-by: Kevin Cernekee <cernekee@gmail.com> Tested-by: Dave Turvene <dturvene@dahetral.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2013-02-14Input: ALPS - move alps_get_model() down below hw_init codeKevin Cernekee
This will minimize the number of forward declarations needed when alps_get_model() starts assigning function pointers. Signed-off-by: Kevin Cernekee <cernekee@gmail.com> Tested-by: Dave Turvene <dturvene@dahetral.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2013-02-14Input: ALPS - copy "model" info into alps_data structKevin Cernekee
Not every type of ALPS touchpad is well-suited to table-based detection. Start moving the various alps_model_data attributes into the alps_data struct so that we don't need a unique table entry for every possible permutation of protocol version, flags, byte0/mask0, etc. Signed-off-by: Kevin Cernekee <cernekee@gmail.com> Tested-by: Dave Turvene <dturvene@dahetral.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2013-02-14Input: ALPS - document the alps.h data structuresKevin Cernekee
Add kernel-doc markup. Signed-off-by: Kevin Cernekee <cernekee@gmail.com> Tested-by: Dave Turvene <dturvene@dahetral.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2013-02-13Input: cyapa - add support for smbus protocolBenson Leung
This patch adds support for the Cypress APA Smbus Trackpad type, which uses a modified register map that fits within the limitations of the smbus protocol. Devices that use this protocol include: CYTRA-116001-00 - Samsung Series 5 550 Chromebook trackpad CYTRA-103002-00 - Acer C7 Chromebook trackpad CYTRA-101003-00 - HP Pavilion 14 Chromebook trackpad Signed-off-by: Dudley Du <dudl@cypress.com> Signed-off-by: Benson Leung <bleung@chromium.org> Reviewed-by: Daniel Kurtz <djkurtz@chromium.org> Reviewed-by: Henrik Rydberg <rydberg@euromail.se> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2013-02-13Input: synaptics - fix 1->3 contact transition reportingDaniel Kurtz
Investigating the following gesture highlighted two slight implementation errors with choosing which slots to report in which slot when multiple contacts are present: Action SGM AGM (MTB slot:Contact) 1. Touch contact 0 (0:0) 2. Touch contact 1 (0:0, 1:1) 3. Lift contact 0 (1:1) 4. Touch contacts 2,3 (0:2, 1:3) In step 4, slot 1 was not being cleared first, which means the same tracking ID was being used for reporting both the old contact 1 and the new contact 3. This could result in "drumroll", where the old contact 1 would appear to suddenly jump to new finger 3 position. Similarly, if contacts 2 & 3 are not detected at the same sample, step 4 is split into two: Action SGM AGM (MTB slot:contact) 1. Touch contact 0 (0:0) 2. Touch contact 1 (0:0, 1:1) 3. Lift contact 0 (1:1) 4. Touch contact 2 (0:2, 1:1) 5. Touch contact 3 (0:2, 1:3) In this case, there was also a bug. In step 4, when contact 1 moves from SGM to AGM and contact 2 is first reported in SGM, slot 0 was actually empty. So slot 0 can be used to report the new SGM (contact 0), immediately. Since it was empty, contact 2 in slot 0 will get a new tracking ID. Signed-off-by: Daniel Kurtz <djkurtz@chromium.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2026-04-21 10:29:21 +0000