| Age | Commit message (Collapse) | Author |
|---|
|
When processing an MPA Start Request, if the listening endpoint is
DEAD, then abort the connection.
If the IWCM returns an error, then we must abort the connection and
release resources. Also abort_connection() should not post a CLOSE
event, so clean that up too.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
These are generated by HW in some error cases and need to be
silently discarded.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
If cxgb4_ofld_send() returns < 0, then send_fw_pass_open_req() must
free the request skb and the saved skb with the tcp header.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Adds support for N-Port VFs, this includes:
1. Adding support in the wrapped FW command
In wrapped commands, we need to verify and convert
the slave's port into the real physical port.
Furthermore, when sending the response back to the slave,
a reverse conversion should be made.
2. Adjusting sqpn for QP1 para-virtualization
The slave assumes that sqpn is used for QP1 communication.
If the slave is assigned to a port != (first port), we need
to adjust the sqpn that will direct its QP1 packets into the
correct endpoint.
3. Adjusting gid[5] to modify the port for raw ethernet
In B0 steering, gid[5] contains the port. It needs
to be adjusted into the physical port.
4. Adjusting number of ports in the query / ports caps in the FW commands
When a slave queries the hardware, it needs to view only
the physical ports it's assigned to.
5. Adjusting the sched_qp according to the port number
The QP port is encoded in the sched_qp, thus in modify_qp we need
to encode the correct port in sched_qp.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some code in the mlx4 IB driver stack assumed MLX4_MAX_PORTS ports.
Instead, we should only loop until the number of actual ports in i
the device, which is stored in dev->caps.num_ports.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Returning directly is easier to read than do-nothing gotos. Remove the
duplicative check on "olp" and pull the code in one indent level.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Improve performance by changing the behavour of the driver when all
SDMA descriptors are in use, and the processes adding new descriptors
are single- or multi-rail.
For single-rail processes, the driver will block the call and finish
posting all SDMA descriptors onto the hardware queue before returning
back to PSM. Repeated kernel calls are slower than blocking.
For multi-rail processes, the driver will return to PSM as quick as
possible so PSM can feed packets to other rail. If all hardware
queues are full, PSM will buffer the remaining SDMA descriptors until
notified by interrupt that space is available.
This patch builds a red-black tree to track the number rails opened by
a particular PID. If the number is more than one, it is a multi-rail
PSM process, otherwise, it is a single-rail process.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Reviewed-by: John A Gregor <john.a.gregor@intel.com>
Reviewed-by: Mitko Haralanov <mitko.haralanov@intel.com>
Signed-off-by: CQ Tang <cq.tang@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
We cannot save the mapped length using the rdma max_page_list_len field
of the ib_fast_reg_page_list struct because the core code uses it. This
results in an incorrect unmap of the page list in c4iw_free_fastreg_pbl().
I found this with dma mapping debugging enabled in the kernel. The
fix is to save the length in the c4iw_fr_page_list struct.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Based on original work from Jay Hernandez <jay@chelsio.com>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Always release the neigh entry in rx_pkt().
Based on original work by Santosh Rastapur <santosh@chelsio.com>.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
find_route() must treat loopback as a valid egress interface.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
There is a four byte hole at the end of the "uresp" struct after the
->qid_mask member.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
These sizes should be unsigned so we don't allow negative values and
have underflow bugs. These can come from the user so there may be
security implications, but I have not tested this.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Fix the following warning for the mlx4 driver:
$ make M=drivers/infiniband C=2 CF=-D__CHECK_ENDIAN__
drivers/infiniband/hw/mlx4/qp.c:1885:31: warning: restricted __be16 degrades to integer
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
drivers/infiniband/hw/ocrdma/ocrdma_verbs.c: In function ‘_ocrdma_modify_qp’:
drivers/infiniband/hw/ocrdma/ocrdma_verbs.c:1299:31: error: ‘old_qps’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
status = ocrdma_mbx_modify_qp(dev, qp, attr, attr_mask, old_qps);
ocrdma_mbx_modify_qp() (and subsequent calls) doesn't appear to use old_qps
so it doesn't need to be passed on. Removing the variable results in the
warning going away.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Acked-by: Devesh Sharma (Devesh.sharma@emulex.com)
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
We don't need to test "ret" twice and also the white space is messed up.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
We already know "pusable" is non-zero, no need to check again.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
%pa format already prints in hexadecimal format, so remove the '0x' annotation
to avoid a double '0x0x' pattern.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
In case of error while accessing to userspace memory, function
nes_create_qp() returns NULL instead of an error code wrapped through
ERR_PTR(). But NULL is not expected by ib_uverbs_create_qp(), as it
check for error with IS_ERR().
As page 0 is likely not mapped, it is going to trigger an Oops when
the kernel will try to dereference NULL pointer to access to struct
ib_qp's fields.
In some rare cases, page 0 could be mapped by userspace, which could
turn this bug to a vulnerability that could be exploited: the function
pointers in struct ib_device will be under userspace total control.
This was caught when using spatch (aka. coccinelle)
to rewrite calls to ib_copy_{from,to}_udata().
Link: https://www.gitorious.org/opteya/ib-hw-nes-create-qp-null
Link: https://www.gitorious.org/opteya/coccib/source/75ebf2c1033c64c1d81df13e4ae44ee99c989eba:ib_copy_udata.cocci
Link: http://marc.info/?i=cover.1394485254.git.ydroneaud@opteya.com
Cc: <stable@vger.kernel.org>
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
In qib_create_ctxts() we allocate an array to hold recv contexts. Then attempt
to create data for those recv contexts. If that call to qib_create_ctxtdata()
fails then an error is returned but the previously allocated memory is not
freed.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Commit af061a644a0e4d4778 add some code in qib_ib_rcv() which
trigger a warning from coccicheck (coccinelle/spatch):
$ make C=2 CHECK=scripts/coccicheck drivers/infiniband/hw/qib/
CHECK drivers/infiniband/hw/qib/qib_verbs.c
drivers/infiniband/hw/qib/qib_verbs.c:679:5-32: code aligned with following code on line 681
CC [M] drivers/infiniband/hw/qib/qib_verbs.o
In fact, according to similar code in qib_kreceive(),
qib_ib_rcv() code is correct but improperly indented.
This patch fix indentation for the misaligned portion.
Link: http://marc.info/?i=cover.1394485254.git.ydroneaud@opteya.com
Cc: Mike Marciniszyn <mike.marciniszyn@intel.com>
Cc: infinipath@intel.com
Cc: Julia Lawall <julia.lawall@lip6.fr>
Cc: cocci@systeme.lip6.fr
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Tested-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Acked-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Commit c804f07248895ff9c moved qib_assign_ctxt() to
do_qib_user_sdma_queue_create() but dropped the braces
around the statements.
This was spotted by coccicheck (coccinelle/spatch):
$ make C=2 CHECK=scripts/coccicheck drivers/infiniband/hw/qib/
CHECK drivers/infiniband/hw/qib/qib_file_ops.c
drivers/infiniband/hw/qib/qib_file_ops.c:1583:2-23: code aligned with following code on line 1587
This patch adds braces back.
Link: http://marc.info/?i=cover.1394485254.git.ydroneaud@opteya.com
Cc: Mike Marciniszyn <mike.marciniszyn@intel.com>
Cc: infinipath@intel.com
Cc: Julia Lawall <julia.lawall@lip6.fr>
Cc: cocci@systeme.lip6.fr
Cc: stable@vger.kernel.org
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Tested-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Acked-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
The counters, unicast_xmit, unicast_rcv, multicast_xmit, multicast_rcv
are now maintained as percpu variables.
The mad code is modified to add a z_ latch so that the percpu counters
monotonically increase with appropriate adjustments in the reset,
read logic to maintain the z_ latch.
This patch also corrects the fact the unitcast_xmit wasn't handled
at all for UC and RC QPs.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
This patch replaces the dd->int_counter with a percpu counter.
The maintanance of qib_stats.sps_ints and int_counter are
combined into the new counter.
There are two new functions added to read the counter:
- qib_int_counter (for a particular qib_devdata)
- qib_sps_ints (for all HCAs)
A z_int_counter is added to allow the interrupt detection logic
to determine if interrupts have occured since z_int_counter
was "reset".
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
The debugfs init code was incorrectly called before the idr mechanism
is used to get the unit number, so the dd->unit hasn't been
initialized. This caused the unit relative directory creation to fail
after the first.
This patch moves the init for the debugfs stuff until after all of the
failures and after the unit number has been determined.
A bug in unwind code in qib_alloc_devdata() is also fixed.
Cc: <stable@vger.kernel.org>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Guard against a potential buffer overrun. The size to read from the
user is passed in, and due to the padding that needs to be taken into
account, as well as the place holder for the ICRC it is possible to
overflow the 32bit value which would cause more data to be copied from
user space than is allocated in the buffer.
Cc: <stable@vger.kernel.org>
Reported-by: Nico Golde <nico@ngolde.de>
Reported-by: Fabian Yamaguchi <fabs@goesec.de>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Guard against a potential buffer overrun. Right now the qib driver is
protected by the fact that the data structure in question is only 16
bits. Should that ever change the problem will be exposed. There is a
similar defect in the ipath driver and this brings the two code paths
into sync.
Reported-by: Nico Golde <nico@ngolde.de>
Reported-by: Fabian Yamaguchi <fabs@goesec.de>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Signed-off-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Fixes to enable the negotiation of the supported IRD/ORD sizes with
the peer when exchanging MPA v2 messages in connection establishment.
Signed-off-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
The current logic suffers from a slow response time to disable user DB
usage, and also fails to avoid DB FIFO drops under heavy load. This commit
fixes these deficiencies and makes the avoidance logic more optimal.
This is done by more efficiently notifying the ULDs of potential DB
problems, and implements a smoother flow control algorithm in iw_cxgb4,
which is the ULD that puts the most load on the DB fifo.
Design:
cxgb4:
Direct ULD callback from the DB FULL/DROP interrupt handler. This allows
the ULD to stop doing user DB writes as quickly as possible.
While user DB usage is disabled, the LLD will accumulate DB write events
for its queues. Then once DB usage is reenabled, a single DB write is
done for each queue with its accumulated write count. This reduces the
load put on the DB fifo when reenabling.
iw_cxgb4:
Instead of marking each qp to indicate DB writes are disabled, we create
a device-global status page that each user process maps. This allows
iw_cxgb4 to only set this single bit to disable all DB writes for all
user QPs vs traversing the idr of all the active QPs. If the libcxgb4
doesn't support this, then we fall back to the old approach of marking
each QP. Thus we allow the new driver to work with an older libcxgb4.
When the LLD upcalls iw_cxgb4 indicating DB FULL, we disable all DB writes
via the status page and transition the DB state to STOPPED. As user
processes see that DB writes are disabled, they call into iw_cxgb4
to submit their DB write events. Since the DB state is in STOPPED,
the QP trying to write gets enqueued on a new DB "flow control" list.
As subsequent DB writes are submitted for this flow controlled QP, the
amount of writes are accumulated for each QP on the flow control list.
So all the user QPs that are actively ringing the DB get put on this
list and the number of writes they request are accumulated.
When the LLD upcalls iw_cxgb4 indicating DB EMPTY, which is in a workq
context, we change the DB state to FLOW_CONTROL, and begin resuming all
the QPs that are on the flow control list. This logic runs on until
the flow control list is empty or we exit FLOW_CONTROL mode (due to
a DB DROP upcall, for example). QPs are removed from this list, and
their accumulated DB write counts written to the DB FIFO. Sets of QPs,
called chunks in the code, are removed at one time. The chunk size is 64.
So 64 QPs are resumed at a time, and before the next chunk is resumed, the
logic waits (blocks) for the DB FIFO to drain. This prevents resuming to
quickly and overflowing the FIFO. Once the flow control list is empty,
the db state transitions back to NORMAL and user QPs are again allowed
to write directly to the user DB register.
The algorithm is designed such that if the DB write load is high enough,
then all the DB writes get submitted by the kernel using this flow
controlled approach to avoid DB drops. As the load lightens though, we
resume to normal DB writes directly by user applications.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Based on original work by Anand Priyadarshee <anandp@chelsio.com>.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To activate RoCE/SRIOV, need to remove the following:
1. In mlx4_ib_add, need to remove the error return preventing
initialization of a RoCE port under SRIOV.
2. In update_vport_qp_params (in resource_tracker.c) need to remove
the error return when a RoCE RC or UD qp is detected.
This error return causes the INIT-to-RTR qp transition to fail
in the wrapper function under RoCE/SRIOV.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* Handle CM_SIDR_REQ_ATTR_ID and CM_SIDR_REP_ATTR_ID
in multiplex_cm_handler and demux_cm_handler.
* Handle Service ID Resolution messages and REQ messages
separately, for their formats are different.
Signed-off-by: Shani Michaeli <shanim@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since there is no connection between the MAC/VLAN and the GID
when using IP-based addressing, the proxy QP1 (running on the
slave) must pass the source-mac, destination-mac, and vlan_id
information separately from the GID. Additionally, the Host
must pass the remote source-mac and vlan_id back to the slave,
This is achieved as follows:
Outgoing MADs:
1. Source MAC: obtained from the CQ completion structure
(struct ib_wc, smac field).
2. Destination MAC: obtained from the tunnel header
3. vlan_id: obtained from the tunnel header.
Incoming MADs
1. The source (i.e., remote) MAC and vlan_id are passed in
the tunnel header to the proxy QP1.
VST mode support:
For outgoing MADs, the vlan_id obtained from the header is
discarded, and the vlan_id specified by the Hypervisor is used
instead.
For incoming MADs, the incoming vlan_id (in the wc) is discarded, and the
"invalid" vlan (0xffff) is substituted when forwarding to the slave.
Signed-off-by: Moni Shoua <monis@mellanox.co.il>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The IB side of RoCE requires the MAC table index of the
MAC address used by its QPs.
To obtain the real MAC index, the IB side registers the
MAC (increasing its ref count, and also returning the
real MAC index) during the modify-qp sequence.
This protects against the ETH side deleting or modifying
that MAC table entry while the QP is active.
Note that until the modify-qp command returns success,
the MAC and VLAN information only has "candidate" status.
If the modify-qp succeeds, the "candidate" info is promoted
to the operational MAC/VLAN info for the qp. If the modify fails,
the candidate MAC/VLAN is unregistered, and the old qp info
is preserved.
The patch is a bit complex, because there are multiple qp
transitions where the primary-path information may be
modified: INIT-to-RTR, and SQD-to-SQD.
Similarly for the alternate path information.
Therefore the code must handle cases where path information
has already been entered into the QP context by previous
qp transitions.
For the MAC address, the success logic is as follows:
1. If there was no previous MAC, simply move the candidate
MAC information to the operational information, and reset
the candidate MAC info.
2. If there was a previous MAC, unregister it. Then move
the MAC information from candidate to operational, and
reset the candidate info (as in 1. above).
The MAC address failure logic is the same for all cases:
- Unregister the candidate MAC, and reset the candidate MAC info.
For Vlan registration, the logic is similar.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The GIDs are statically distributed, as follows:
PF: gets 16 GIDs
VFs: Remaining GIDS are divided evenly between VFs activated by the driver.
If the division is not even, lower-numbered VFs get an extra GID.
For an IB interface, the number of gids per guest remains as before: one gid per guest.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This requires the following modifications:
1. Fix build_mlx4_header to properly fill in the ETH fields
2. Adjust mux and demux QP1 flow to support RoCE.
This commit still assumes only one GID per slave for RoCE.
The commit enabling multiple GIDs is a subsequent commit, and
is done separately because of its complexity.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently support only T10-DIF types of signature handover operations
(types 1|2|3).
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
This commit takes care of the generated signature error CQE generated
by the HW (if happened). The underlying mlx5 driver will handle
signature error completions and will mark the relevant memory region
as dirty.
Once the consumer gets the completion for the transaction, it must
check for signature errors on signature memory region using a new
lightweight verb ib_check_mr_status().
In case the user doesn't check for signature error (i.e. doesn't call
ib_check_mr_status() with status check IB_MR_CHECK_SIG_STATUS), the
memory region cannot be used for another signature operation
(REG_SIG_MR work request will fail).
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
This patch implements IB_WR_REG_SIG_MR posted by the user.
Baisically this WR involves 3 WQEs in order to prepare and properly
register the signature layout:
1. post UMR WR to register the sig_mr in one of two possible ways:
* In case the user registered a single MR for data so the UMR data segment
consists of:
- single klm (data MR) passed by the user
- BSF with signature attributes requested by the user.
* In case the user registered 2 MRs, one for data and one for protection,
the UMR consists of:
- strided block format which includes data and protection MRs and
their repetitive block format.
- BSF with signature attributes requested by the user.
2. post SET_PSV in order to set the memory domain initial
signature parameters passed by the user.
SET_PSV is not signaled and solicited CQE.
3. post SET_PSV in order to set the wire domain initial
signature parameters passed by the user.
SET_PSV is not signaled and solicited CQE.
* After this compound WR we place a small fence for next WR to come.
This patch also introduces some helper functions to set the BSF correctly
and determining the signature format selectors.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
get_umr_flags helper function might be used for types of access modes
other than ACCESS_MODE_MTT, such as ACCESS_MODE_KLM. So remove it from
helper, and callers will add their own access mode flag.
This commit does not add/change functionality.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
As a preliminary step for signature feature which will require posting
multiple (3) WQEs for a single WR, we break post_send routine WQE
indexing into begin and finish routines.
This patch does not change any functionality.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
If user requested signature enable we initialize relevant mlx5_ib_qp
members. We mark the qp as sig_enable and we increase the effective
SQ size, but still limit the user max_send_wr to original size
computed. We also allow the create_qp routine to accept sig_enable
create flag.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Support create_mr and destroy_mr verbs. Creating ib_mr may be done
for either ib_mr that will register regular page lists like
alloc_fast_reg_mr routine, or indirect ib_mrs that can register other
(pre-registered) ib_mrs in an indirect manner.
In addition user may request signature enable, that will mean that the
created ib_mr may be attached with signature attributes (BSF, PSVs).
Currently we only allow direct/indirect registration modes.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
This patch refactors the IB core umem code and vendor drivers to use a
linear (chained) SG table instead of chunk list. With this change the
relevant code becomes clearer—no need for nested loops to build and
use umem.
Signed-off-by: Shachar Raindel <raindel@mellanox.com>
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Bump all Mellanox driver versions.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
