| Age | Commit message (Collapse) | Author |
|---|
|
commit 59d92bfa5f0cdf57f82f5181b0ad6af75c3fdf41 upstream.
We've simply ignored this, which isn't too great. With this, interlaced
1080i works on my HDMI screen connected through sdvo. For no apparent
reason anything else still doesn't work as it should.
While at it, give these magic numbers in the dtd proper names and
add a comment that they match with EDID detailed timings.
v2: Actually use the right bit for interlaced.
Tested-by: Peter Ross <pross@xvid.org>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Chris Wilson dug out a hw erratum saying that there's noise on the
interrupt line on i945G chips. We also have a bug report from a i945GM
chip with an sdvo hotplug interrupt storm (and no apparent cause).
Play it safe and disable sdvo hotplug on all i945 variants.
Note that this is a regression that has been introduced in 3.1,
when we've enabled sdvo hotplug support with
commit cc68c81aed7d892deaf12d720d5455208e94cd0a
Author: Simon Farnsworth <simon.farnsworth@onelan.co.uk>
Date: Wed Sep 21 17:13:30 2011 +0100
drm/i915: Enable SDVO hotplug interrupts for HDMI and DVI
Cc: stable@kernel.org
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=38442
Reported-and-tested-by: Dominik Köppl <dominik@devwork.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
We seem to have a decent confusion between the output timings and the
input timings of the sdvo encoder. If I understand the code correctly,
we use the original mode unchanged for the output timings, safe for
the lvds case. And we should use the adjusted mode for input timings.
Clarify the situation by adding an explicit output_dtd to the sdvo
mode_set function and streamline the code-flow by moving the input and
output mode setting in the sdvo encode together.
Furthermore testing showed that the sdvo input timing needs the
unadjusted dotclock, the sdvo chip will automatically compute the
required pixel multiplier to get a dotclock above 100 MHz.
Fix this up when converting a drm mode to an sdvo dtd.
This regression was introduced in
commit c74696b9c890074c1e1ee3d7496fc71eb3680ced
Author: Pavel Roskin <proski@gnu.org>
Date: Thu Sep 2 14:46:34 2010 -0400
i915: revert some checks added by commit 32aad86f
particularly the following hunk:
diff --git a/drivers/gpu/drm/i915/intel_sdvo.c
b/drivers/gpu/drm/i915/intel_sdvo.c
index 093e914..62d22ae 100644
--- a/drivers/gpu/drm/i915/intel_sdvo.c
+++ b/drivers/gpu/drm/i915/intel_sdvo.c
@@ -1122,11 +1123,9 @@ static void intel_sdvo_mode_set(struct drm_encoder *encoder,
/* We have tried to get input timing in mode_fixup, and filled into
adjusted_mode */
- if (intel_sdvo->is_tv || intel_sdvo->is_lvds) {
- intel_sdvo_get_dtd_from_mode(&input_dtd, adjusted_mode);
+ intel_sdvo_get_dtd_from_mode(&input_dtd, adjusted_mode);
+ if (intel_sdvo->is_tv || intel_sdvo->is_lvds)
input_dtd.part2.sdvo_flags = intel_sdvo->sdvo_flags;
- } else
- intel_sdvo_get_dtd_from_mode(&input_dtd, mode);
/* If it's a TV, we already set the output timing in mode_fixup.
* Otherwise, the output timing is equal to the input timing.
Due to questions raised in review, below a more elaborate analysis of
the bug at hand:
Sdvo seems to have two timings, one is the output timing which will be
sent over whatever is connected on the other side of the sdvo chip (panel,
hdmi screen, tv), the other is the input timing which will be generated by
the gmch pipe. It looks like sdvo is expected to scale between the two.
To make things slightly more complicated, we have a bunch of special
cases:
- For lvds panel we always use a fixed output timing, namely
intel_sdvo->sdvo_lvds_fixed_mode, hence that special case.
- Sdvo has an interface to generate a preferred input timing for a given
output timing. This is the confusing thing that I've tried to clear up
with the follow-on patches.
- A special requirement is that the input pixel clock needs to be between
100MHz and 200MHz (likely to keep it within the electromechanical design
range of PCIe), 270MHz on later gen4+. Lower pixel clocks are
doubled/quadrupled.
The thing this patch tries to fix is that the pipe needs to be
explicitly instructed to double/quadruple the pixels and needs the
correspondingly higher pixel clock, whereas the sdvo adaptor seems to
do that itself and needs the unadjusted pixel clock. For the sdvo
encode side we already set the pixel mutliplier with a different
command (0x21).
This patch tries to fix this mess by:
- Keeping the output mode timing in the unadjusted plain mode, safe
for the lvds case.
- Storing the input timing in the adjusted_mode with the adjusted
pixel clock. This way we don't need to frob around with the core
crtc mode set code.
- Fixing up the pixelclock when constructing the sdvo dtd timing
struct. This is why the first hunk of the patch is an integral part
of the series.
- Dropping the is_tv special case because input_dtd is equivalent to
adjusted_mode after these changes. Follow-up patches clear this up
further (by simply ripping out intel_sdvo->input_dtd because it's
not needed).
v2: Extend commit message with an in-depth bug analysis.
Reported-and-Tested-by: Bernard Blackham <b-linuxgit@largestprime.net>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=48157
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: stable@kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
While fixing up a merge conflict with drm-next I've noticed that we
use the same audio drm connector property also for dp and sdvo
outputs.
So put the new enum to some good use and convert these paths, too. The
HDMI_AUDIO_ prefix is a bit a misnomer. But at least for sdvo it makes
sense (and you can also connect a hdmi monitor with a dp->hdmi cable),
so I've decided to stick with it.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Manually resolve the conflict between the new enum drm property
helpers in drm-next and the new "force-dvi" option that the "audio" output
property gained in drm-intel-next.
While resolving this conflict, switch the new drm_prop_enum_list to
use the newly introduced enum defines instead of magic values.
Conflicts:
drivers/gpu/drm/i915/intel_modes.c
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Signed-off-by: Peter Ross <pross@xvid.org>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Christopher Egert <cme3000@gmail.com>
Tested-by: Alfonso Fiore <alfonso.fiore@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
We have a pretty decent confusion about vertical timings of interlaced
modes. Peter Ross has written a patch that makes interlace modes work
on a lot more platforms/output combinations by doubling the vertical
timings.
The issue with that patch is that core drm _does_ support specifying
whether we want these vertical timings in fields or frames, we just
haven't managed to consistently use this facility. The relavant
function is drm_mode_set_crtcinfo, which fills in the crtc timing
information.
The first thing to note is that the drm core keeps interlaced modes in
frames, but displays modelines in fields. So when the crtc modeset
helper copies over the mode into adjusted_mode it will already contain
vertical timings in half-frames. The result is that the fixup code in
intel_crtc_mode_fixup doesn't actually do anything (in most cases at
least).
Now gen3+ natively supports interlaced modes and wants the vertical
timings in frames. Which is what sdvo already fixes up, at least under
some conditions.
There are a few other place that demand vertical timings in fields
but never actually deal with interlaced modes, so use frame timings
for consistency, too. These are:
- lvds panel,
- dvo encoders - dvo is the only way gen2 could support interlaced
mode, but currently we don't support any encoders that do.
- tv out - despite that the tv dac sends out an interlaced signal it
expects a progressive mode pipe configuration.
All these encoders enforce progressive modes by resetting
interlace_allowed.
Hence we always want crtc vertical timings in frames. Enforce this in
our crtc mode_fixup function and rip out any redudant timing
computations from the encoders' mode_fixup function.
v2-4: Adjust the vertical timings a bit.
v5: Split out the 'subtract-one for interlaced' fixes.
v6: Clarify issues around tv-out and gen2.
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Christopher Egert <cme3000@gmail.com>
Tested-by: Alfonso Fiore <alfonso.fiore@gmail.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Creating a range property is a common pattern, so create
a convenience function for this and use it where appropriate.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
This is a revert of 81a14b46846fea0741902e8d8dfcc6c6c78154c8.
We already set the mode polarity using the SDVO commands with struct
intel_sdvo_dtd. We have at least 3 bugs that get fixed with this patch.
The documentation, despite not clear, can also be interpreted in a way
that suggests this patch is needed.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=15766
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=42174
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=43333
Cc: stable@kernel.org
Reviewed-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
We were checking whether the supplied edid matched the connector it was
read from. We do this in case a DDC read returns an EDID for another
device on a multifunction or otherwise interesting card. However, we
failed to include LVDS as a digital device and so rejecting an otherwise
valid EDID.
Fixes the detection of the secondary SDVO LVDS panel on the Libretto
W105.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=39216
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
v2: add a CPT-specific macro, make code cleaner
v3: fix commit message
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=41272
Cc: stable@kernel.org
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
They need this to get all the EXPORT_SYMBOL variants and THIS_MODULE
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Well almost anyway. IVB has 3 planes, pipes, transcoders, and FDI
interfaces, but only 2 pipe PLLs. So two of the pipes must use the same
pipe timings (e.g. 2 DP plus one other, or two HDMI with the same mode
and one other, etc.).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-By: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-By: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
Signed-off-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
This is general TMDS detect, not HDMI specifically.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
I can't think of any sensible reason to limit this to a mask of 0x0f,
ie, SDVO_OUTPUT_{TMDS,RGB,CVBS,SVID}0.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
I have no evidence for this byte being used this way, and lots of
counterexamples. Restore the struct to its empirical definition and
patch up gmbus setup to match.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
|
|
I was seeing a nasty 5 frame glitch every 10 seconds, caused by the
poll for connection on DVI attached by SDVO.
As my SDVO DVI supports hotplug detect interrupts, the fix is to
enable them, and hook them in to the various bits of driver
infrastructure so that they work reliably.
Note that this is only tested on single-function DVI-D SDVOs, on two
platforms (965GME and 945GSE), and has not been checked against a
specification document.
With lots of help from Adam Jackson <ajax@redhat.com> on IRC.
Signed-off-by: Simon Farnsworth <simon.farnsworth@onelan.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
Various issues involved with the space character were generating
warnings in the checkpatch.pl file. This patch removes most of those
warnings.
Signed-off-by: Akshay Joshi <me@akshayjoshi.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
Make the audio property creation routine common and share the single
property between the connectors.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
The ddc proxy depends upon the underlying i2c bus being selected. Under
certain configurations, the i2c-adapter functionality is queried during
initialisation and so may trigger an OOPS during boot. Hence, we need to
reorder the initialisation of the ddc proxy until after we hook up the i2c
adapter for the SDVO device.
The condition under which it fails is when the i2c_add_adapter calls
into i2c_detect which will attempt to probe all valid addresses on the
adapter iff there is a pre-existing i2c_driver with the same class as
the freshly added i2c_adapter.
So it appears to depend upon having compiled in (or loaded such a
module before i915.ko) an i2c-driver that likes to futz over the
i2c_adapters claiming DDC support.
Reported-by: Mihai Moldovan <ionic@ionic.de>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
* 'intel/drm-intel-next' of ../drm-next: (755 commits)
drm/i915: Only wait on a pending flip if we intend to write to the buffer
drm/i915/dp: Sanity check eDP existence
drm/i915: Rebind the buffer if its alignment constraints changes with tiling
drm/i915: Disable GPU semaphores by default
drm/i915: Do not overflow the MMADDR write FIFO
Revert "drm/i915: fix corruptions on i8xx due to relaxed fencing"
drm/i915: Don't save/restore hardware status page address register
drm/i915: don't store the reg value for HWS_PGA
drm/i915: fix memory corruption with GM965 and >4GB RAM
Linux 2.6.38-rc7
Revert "TPM: Long default timeout fix"
drm/i915: Re-enable GPU semaphores for SandyBridge mobile
drm/i915: Replace vblank PM QoS with "Interrupt-Based AGPBUSY#"
Revert "drm/i915: Use PM QoS to prevent C-State starvation of gen3 GPU"
drm/i915: Allow relocation deltas outside of target bo
drm/i915: Silence an innocuous compiler warning for an unused variable
fs/block_dev.c: fix new kernel-doc warning
ACPI: Fix build for CONFIG_NET unset
mm: <asm-generic/pgtable.h> must include <linux/mm_types.h>
x86: Use u32 instead of long to set reset vector back to 0
...
Conflicts:
drivers/gpu/drm/i915/i915_gem.c
|
|
... and fixup some methods to accept the constant argument.
Now that constant module arrays are loaded into read-only memory, using
const appropriately has some benefits beyond warning the programmer
about likely mistakes.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
In order to prevent "crushed blacks" on TVs, the range of the RGB output
may be limited to 16-235. This used to be available through Xorg under
the "Broadcast RGB" option, so reintroduce support for KMS.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=34543
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
Grab the latest stabilisation bits from -fixes and some suspend and
resume fixes from linus.
Conflicts:
drivers/gpu/drm/i915/i915_drv.h
drivers/gpu/drm/i915/i915_irq.c
|
|
If the user changes the force-audio property and it no longer reflects
the current configuration, then we need to trigger a mode set in order
to update the registers.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
If we have an EDID for a digital panel, but we are probing a non-TMDS
connector then we know that this is a false detection, and vice versa.
This should reduce the number of bogus outputs on multi-function
adapters that report the same output on multiple connectors.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=34101
Reported-by: Sebastien Caty <sebastien.caty@mrnf.gouv.qc.ca>
Tested-by: Sebastien Caty <sebastien.caty@mrnf.gouv.qc.ca>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
|
|
Merge resume fixes from -fixes and an important fix for SDVO GMBUS.
|
|
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
We were not pausing after detecting the response was pending and so did
not allow the hardware sufficient time to complete before aborting. This
lead to transient failures whilst probing SDVO devices.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=30235
Reported-by: Knut Petersen <Knut_Petersen@t-online.de>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
Alex Fiestas reported an issue with his HDMI connector being misdetected
as DVI unless he had something connected upon boot. By moving the
decision as to whether to use HDMI or DVI encoding for the HDMI capable
output until we probe the monitor means that we should avoid sending a
HDMI signal to a DVI monitor and also correctly detect hardware like
Alex's.
However, to really determine what connector is soldered onto the wire we
need to inspect the VBT sdvo child devices - but can we trust it?
Reported-by: Alex Fiestas <alex@eyeos.org>
Tested-by: Alex Fiestas <alex@eyeos.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=32828
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
|
|
|
|
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=25012
Reported-by: Tõnu Raitviir <jussuf@linux.ee>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
This is even more important as those bits will be moved in future.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
BIOSes. Can't live without them (apparently), definitely can't live with
them.
Reported-by: Ben Gamari <bgamari@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=24312
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
Commit d09c23de intended to add a 30ms delay to give the ADD time to
detect any TVs connected. However, it used the sdvo->is_tv flag to do so
which is dependent upon the previous detection result and not whether the
output supports TVs.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
|
|
On a few devices, like the Mac Mini, the CRT DDC pins are shared between
the analog connector and the digital connector. In this scenario, rely
on the EDID to determine if a digital panel is connected to the digital
connector.
Reported-and-tested-by: Tino Keitel <tino.keitel@tikei.de>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
As we conflated intel_sdvo->is_hdmi with both having HDMI support on the
ADD along with having HDMI support on the monitor, we would attempt to
use HDMI encodings even if the interface did not support those commands.
Reported-by: Simon Farnsworth <simon.farnsworth@onelan.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Simon Farnsworth <simon.farnsworth@onelan.co.uk>
Reviewed-by: Simon Farnsworth <simon.farnsworth@onelan.co.uk>
|
|
This block is only used when detecting whether the connector is HDMI and
never again, so scope the variable to the detection routine.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
This patch enables the sending of AVI infoframes in
drivers/gpu/drm/i915/intel_hdmi.c.
My receiver currently loses sync when the HDMI output on my computer
(DG45FC motherboard) is switched from 800x600 (the BIOS resolution) to
1920x1080 as part of the boot. Fixable by switching inputs on the receiver
a couple of times.
With this patch, my receiver has not lost sync yet (> 40 tries).
Fourth version, now based on drm-intel-next from:
git://git.kernel.org/pub/scm/linux/kernel/git/ickle/drm-intel.git
Two questions still remain:
I'm assuming that the sdvo hardware also stores a header ECC byte in
the MSB of the first dword - is this correct?
Does the SDVOB and SDVOC handling in intel_hdmi_set_avi_infoframe()
look correct?
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
Allow the user to override the detection of the sink's audio capabilities
from EDID. Not all sinks support the required EDID level to specify
whether they handle audio over the display connection, so allow the user
to enable it manually.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
|
|
Besides a couple of bugs when writing more than a single byte along the
GMBUS, SDVO was completely failing whilst trying to use GMBUS, so use
bit banging instead.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
In the event that the external chipset doesn't implement the
GET_SUPPORTED_ENHANCEMENTS commands, gracefully treat it as having no
enhancments rather than bailing.
Reported-and-tested-by: Woody Suwalski <terraluna977@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=18342
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
We weren't unlinking the freed connector from the drm lists, and so
hit some use-after-free if we failed to initialise the connector.
Reported-and-tested-by: Woody Suwalski <terraluna977@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=18342
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
Avoid confusion between i965g meaning broadwater and the gen4+ chipset
families.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
Conflicts:
drivers/char/agp/intel-agp.c
drivers/gpu/drm/i915/intel_crt.c
|
|
Use the GMBUS interface rather than direct bit banging to grab the EDID
over DDC (and for other forms of auxiliary communication with external
display controllers). The hope is that this method will be much faster
and more reliable than bit banging for fetching EDIDs from buggy monitors
or through switches, though we still preserve the bit banging as a
fallback in case GMBUS fails.
Based on an original patch by Jesse Barnes.
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
